Photocatalytic behavior of heavy La-doped TiO2 films deposited by pulsed laser deposition using non-sintered target

We have investigated the control of photocatalytic behavior under deposited conditions of non-sintered target of different molar ratios with TiO₂ and La₂O₃ from 1:0 to 1:2 for heavily La doping, and post-annealing temperature from 600 °C to 1000 °C for crystallizing by pulsed laser deposition. We have successfully crystallized heavily La-doped TiO₂ films with post-annealing temperature over 800 °C and with molar ratio of TiO₂:La₂O₃ over 1:1 on a quartz substrate. Heavily La-doped TiO₂ films are observed the decomposition of methylene blue and a water-splitting reaction in photocatalytic behavior under Xe light irradiation. When stoichiometric La-doped TiO₂ (TiO₂:La₂O₃ = 1: 1) is synthesized with heat-treatment at 900 °C, the best results are obtained under photocatalytic behavior and pure La₂Ti₂O₇ crystalline were obtained.     

Aerosol-assisted flow synthesis of WxTi1−xO2 solid solution spheres with enhanced photocatalytic activity

In this paper, W_xTi_1−xO₂ solid solutions (x = 0.000, 0.005, 0.010, 0.015, and 0.020) microspheres were synthesized with an aerosol-assisted flow synthesis method. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen sorption, UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the as-prepared catalysts were measured by the degradation of rhodamine B (RhB) under visible light irradiation (λ ≥ 420 nm). All the solid solutions exhibited higher photocatalytic activities than pure TiO₂ and the W_0.015Ti_0.985O₂ solid solution possessed the highest photocatalytic activity. The degradation constant of RhB on W_0.015Ti_0.985O₂ solid solution catalyst was about 15 times of that of the pure TiO₂ and 25 times of that of Degussa P25, respectively. This study provides an effective method to prepare visible light photocatalysts on a large scale.     

Enhanced optical activation of Er in Er-doped Al2O3 powders by Y codoping in a sol-gel method

Enhanced photoluminescence (PL) mechanism of Er³⁺-doped Al₂O₃ powders by Y³⁺ codoping at wavelength 1.53 μm has been investigated through PL measurements of 0.1 mol% Er³⁺- and 0-20 mol% Y³⁺-codoped Al₂O₃ powders prepared at a sintering temperature of 900 °C in a non-aqueous sol-gel method. PL intensity and lifetime of Er³⁺-Y³⁺-codoped Al₂O₃ powders composed of γ-(Al,Er,Y)₂O₃ and θ-(Al,Er,Y)₂O₃ phases increased with increasing Y³⁺-codoping concentration. The 10-20 mol% Y³⁺ codoping in 0.1 mol% Er³⁺-doped Al₂O₃ powders intensified the PL intensity by about 20 times, with a PL lifetime prolonged from 3.5 to 5.8 ms. A maximal increase of the optical activity of Er³⁺ in 0.1 mol% Er³⁺-Y³⁺-codoped Al₂O₃ powders about one order was achieved by 10-20 mol% Y³⁺ codoping. It is found that the improved PL properties for Er³⁺-Y³⁺-codoped Al₂O₃ powders are mainly attributed to enhanced optical activation of Er³⁺ in the Al₂O₃ by Y³⁺ codoping, and to the slightly increased radiative quantum efficiency of Er³⁺ in the Al₂O₃.     

Spectral properties of Nd-doped Sr3Ga2Ge4O14 crystal

Neodymium doped strontium gallogermanate crystals were grown successfully by the Bridgman technique. The linear thermal expansion coefficients for the c- and a-axes were measured as 5.8 × 10⁻⁶ °C⁻¹ and 6.5 × 10⁻⁶ °C⁻¹. Absorption spectra, and fluorescence spectra, as well as fluorescence decay curves of Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal, have been recorded at room temperature and used to calculate the absorption and stimulated emission cross-sections. Based on the Judd-Ofelt theory, three intensity parameters were obtained. The luminescent quantum efficiency of the ⁴F_3/2 level was determined to be approximately 73.8% for this material. Compared with other Nd³⁺-doped laser crystals, Nd³⁺-doped Sr₃Ga₂Ge₄O₁₄ crystal displays special laser properties due to its disorder structure.     

The effect of additional doping with Nb, Al or Cu on ferromagnetism and conductivity in V-doped TiO2 powders

Rutile Ti_0.94V_0.06O₂ and Ti_0.93V_0.06M_0.01O₂ (M=Nb, Al, and Cu) polycrystalline powders are synthesized by the standard solid-state reaction method. The room-temperature saturation magnetization and resistivity of Ti_0.94V_0.06O₂ powders are 2.5×10⁻³ emu/g (≈0.60×10⁻³μ_B/V) and above 10⁷ Ω cm, respectively. The ferromagnetism weakens remarkably, and the conductivity enhances after additional doping with Nb or Al in V-doped rutile TiO₂ powders. The room-temperature magnetization and resistivity of Ti_0.93V_0.06Cu_0.01O₂ powders are 2.1×10⁻³ emu/g and 1.26×10⁶ Ω cm, respectively. Based on analysis for chemical valence of dopants by the x-ray photoelectron spectroscopy spectra, and using the bound magnetic polaron model, the microscopic mechanisms of ferromagnetism in V-doped rutile TiO₂ powders with or without additional dopants are discussed in detail.     

Influence of postdeposition annealing on structural properties and electrical characteristics of thin Tm2O3 and Tm2Ti2O7 dielectrics

We describe the structural properties and electrical characteristics of thin thulium oxide (Tm₂O₃) and thulium titanium oxide (Tm₂Ti₂O₇) as gate dielectrics deposited on silicon substrates through reactive sputtering. The structural and morphological features of these films were explored by X-ray diffraction, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and atomic force microscopy, measurements. It is found that the Tm₂Ti₂O₇ film annealed at 800 °C exhibited a thinner capacitance equivalent thickness of 19.8 Å, a lower interface trap density of 8.37 × 10¹¹ eV⁻¹ cm⁻², and a smaller hysteresis voltage of ∼4 mV than the other conditions. We attribute this behavior to the Ti incorporated into the Tm₂O₃ film improving the interfacial layer and the surface roughness. This film also shows negligible degrees of charge trapping at high electric field stress.     

Stabilization of a very high-k crystalline ZrO2 phase by post deposition annealing of atomic layer deposited ZrO2/La2O3 dielectrics on germanium

The impact of the ZrO₂/La₂O₃ film thickness ratio and the post deposition annealing in the temperature range between 400 °C and 600 °C on the electrical properties of ultrathin ZrO₂/La₂O₃ high-k dielectrics grown by atomic layer deposition on (1 0 0) germanium is investigated. As-deposited stacks have a relative dielectric constant of 24 which is increased to a value of 35 after annealing at 500 °C due to the stabilization of tetragonal/cubic ZrO₂ phases. This effect depends on the absolute thickness of ZrO₂ within the dielectric stack and is limited due to possible interfacial reactions at the oxide/Ge interface. We show that adequate processing leads to very high-k dielectrics with EOT values below 1 nm, leakage current densities in the range of 0.01 A/cm², and interface trap densities in the range of 2-5 × 10¹² eV⁻¹ cm⁻².     

Effect of concentration on the luminescence of Eu ions in nanocrystalline La2O3

Nanocrystalline powders with various Eu³⁺ concentration (from 1 to 10 mol %) doped La₂O₃ were prepared via a combustion route. Their structure and morphology were characterized using X-ray diffraction (XRD) and High-resolution transmission electron microscopy. The emission spectra of the as-synthesized samples show that the strongest emission position is centered at 626 nm corresponding to ⁵D₀→⁷F₂ transition of Eu³⁺ ions and the intensity change of 626 nm emission is considered as a function of ultraviolet (240 nm) irradiation time. The excitation spectra at 626 nm monitoring indicate that the charge transfer state band is varies with different Eu³⁺ ion concentration. These results are attributed to the surface defects of the nanocrystals.     

Low voltage electron induced cathodoluminescence degradation and surface characterization of Sr3(PO4)2:Tb phosphor

Tb³⁺-doped Sr₃(PO₄)₂ phosphor was prepared by a sol-gel combustion method. A trigonal structure having Sr and O atoms occupying two different lattice sites were obtained. Scanning Auger nanoprobe was used to analyze the morphology of the particles. Photoluminescence (PL) and cathodoluminescence (CL) properties of Sr₃(PO₄)₂:Tb powder phosphors were evaluated and compared. In addition, the CL intensity degradation of Sr₃(PO₄)₂:Tb was evaluated when the powders were irradiated with a beam of electrons in a vacuum chamber maintained at an O₂ pressure of 1 × 10⁻⁶ Torr or a background pressure of 1 × 10⁻⁸ Torr O₂. The surface chemical composition of the degraded powders, analyzed by X-ray photoelectron spectroscopy (XPS), suggests that new compounds (metal oxides) of strontium and phosphorous were formed on the surface. It is most likely that these compounds contributed to the CL intensity degradation of the Sr₃(PO₄)₂:Tb phosphors. The CL properties and possible mechanism by which the new metal oxides were formed on the surface due to a prolonged electron beam irradiation are discussed.     

Reasons for the deactivation of Pt/TiO2 photocatalyst treated by inert gas N2

The effect of N₂ treatment on the photocatalytic activity of Pt⁰/TiO₂ was investigated. The results showed that after treatment at 500 °C in N₂, 70% of the photocatalytic activity of 1.0 wt.% Pt⁰/TiO₂ was lost by the evaluation of photocatalytic oxidation reaction of C₃H₆. Transmission electron microscopy (TEM) and Ar⁺ ion sputtering tests revealed that in the course of high-temperature N₂ treatment, the size of Pt⁰ particles on TiO₂ increases and a strong interaction between metal and support, i.e. Pt⁰ particles encapsulated by Ti_xO_y, happens, which are the reasons for the deactivation of Pt⁰/TiO₂ photocatalyst treated by high-temperature N₂.     

Preparation and characterization of visible light responsive Fe2O3-TiO2 composites

In this study we present the effects of iron oxide (Fe₂O₃) on titanium dioxide (TiO₂) in synthesising visible-light reactive photocatalysts. A Fe₂O₃-TiO₂ composite photocatalyst was synthesized from Fe₂(SO₄)₃ and Ti(SO₄)₂ by a ethanol-assisted hydrothermal method. The preparation conditions were optimized through the investigation of the effects of hydrothermal temperature and time as well as molar ratio of Ti to Fe on the photocatalytic activity. The visual, physical and chemical properties of the Fe₂O₃-TiO₂ composites were investigated. The results showed that α-Fe₂O₃ and anatase TiO₂ were present in the composites. The Fe₂O₃-TiO₂ synthesized under optimum condition consisted of mesoporous structure with an average pore size of 4 nm and a surface area of 43 m²/g. Under visible and solar light irradiation, the photocatalytic activity of optimized sample was significantly higher than that of pure TiO₂. This sample led to a photodegradation efficiency of 90% and 40% of auramine under visible light and solar light, respectively.     

Synthesis and characterization of wire-like and near-spherical Eu2O3-doped Y2O3 phosphors by solvothermal reaction

Eu₂O₃-doped yttrium oxide (3 mol%) [Y₂O₃:Eu(3 mol%)] with wire-like and near-spherical morphologies were prepared by a solvothermal treatment using water, ethanol, ethylene glycol and glycerol as reaction media followed by calcination. The powders prepared in water and ethanol possessed wire structure, where the powder treated in water showed high aspect ratio and that in ethanol showed low aspect ratio. The powders prepared in ethylene glycol and glycerol possessed well-dispersed near-spherical powders, which showed almost the same level of photoluminescence emission intensity as that of submicron particles prepared without solvothermal treatment.     

TiO2 thick films supported on reticulated macroporous Al2O3 foams and their photoactivity in phenol mineralization

TiO₂ thick films deposited on macroporous reticulated Al₂O₃ foams with pore size of 10 ppi and 15 ppi were prepared using dip coating from slurries of Aeroxide^® P25 nanopowder and precipitated titania. All prepared films have sufficiently good adhesion to the surface of the substrate also in case of strongly cracked films. No measurable release of deposited TiO₂ after repeated photocatalytic cycles was observed. The photocatalytic activity was characterized as the rate of mineralization of aqueous phenol solution under irradiation of UVA light by TOC technique. The best activity was obtained with Aeroxide^® P25 coated Al₂O₃ foam with the pore size of 10 ppi, annealed at 600 °C. The optimal annealing temperature for preparation of films from precipitated titania could be determined at 700 °C. Films prepared by sol-gel deposition technique were considerably thinner compared to coatings made of suspensions and their photocatalytic activity was significantly smaller.     

Electrical properties of La2O3 thin films grown on TiN/Si substrates via atomic layer deposition

The electrical as well as the structural properties of La₂O₃ thin films on TiN substrates were investigated. Amorphous stoichiometric La₂O₃ thin films were grown at 300 °C via atomic layer deposition technique by using lanthanum 2,2,6,6-tetramethyl-3,5-heptanedione [La(TMHD)₃] and H₂O as precursors. Post-annealing of the grown film induced dramatic changes in structural and the electrical properties. Crystalline phases of the La₂O₃ film emerged with the increase of the post-annealing temperature. Metal-insulator-metal (MIM) capacitor was fabricated to measure the electrical properties of the grown film. The dielectric constant of the La₂O₃ thin films increased with annealing temperature to reach the value of 17.3 at 500 °C. The leakage current density of the film post-annealed at 400 °C was estimated to be 2.78 × 10⁻¹⁰ and 2.1 × 10⁻⁸ A/cm² at ±1 V, respectively.     

Synthesis of Gd2Ti2O7:Eu, V phosphors by sol-gel process and its luminescent properties

A red-emitting phosphor material, Gd₂Ti₂O₇:Eu³⁺, V⁴⁺, by added vanadium ions is synthesized using the sol-gel method. Phosphor characterization by high-resolution transmission electron microscopy shows that the phosphor possesses a good crystalline structure, while scanning electron microscopy reveals a uniform phosphor particle size in the range of 230-270 nm. X-ray photon electron spectrum analysis demonstrates that the V⁴⁺ ion promotes an electron dipole transition of Gd₂Ti₂O₇:Eu³⁺ phosphors, causing a new red-emitting phenomenon, and CIE value shifts to x=0.63, y=0.34 (a purer red region) from x=0.57, y=0.33 (CIE of Gd₂Ti₂O₇:Eu³⁺). The optimal composition of the novel red-emitting phosphor is about 26% of V⁴⁺ ions while the material is calcinated at 800  °C. The results of electroluminescent property of the material by field emission experiment by CNT-contained cathode agreed well with that of photoluminescent analysis.     

Influence of Lu2O3 on electrical and microstructural properties of CaCu3Ti4O12 ceramics

In this work, the influence of Lu₂O₃ doped on the dielectric and electrical properties of CaCu₃Ti₄O₁₂ was reported. Lu₂O₃-doped CCTO was prepared by a conventional solid state technique using CuO, TiO₂, and CaCO₃ as starting materials. The samples were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM); dielectric measurements were measured in the 10² Hz–10⁷ Hz frequency range at room temperature; and the nonlinear behavior of all samples was measured. The doping of Lu₂O₃ resulted in an increase in the dielectric constant of CCTO, but decreased the stability of the frequency dependence. Increasing concentrations of Lu₂O₃ resulted in decreasing nonlinear coefficients.     

Ferroelectric properties of bilayer structured Pb(Zr0.52Ti0.48)O3/SrBi2Ta2O9 (PZT/SBT) thin films on Pt/TiO2/SiO2/Si substrates

Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films with large remanent polarization and SrBi₂Ta₂O₉ (SBT) thin films with excellent fatigue-resisting characteristic have been widely studied for non-volatile random access memories, respectively. To combine these two advantages_, bilayered Pb(Zr_0.52Ti_0.48)O₃/SrBi₂Ta₂O₉ (PZT/SBT) thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates by chemical solution deposition method. X-ray diffraction patterns revealed that the diffraction peaks of PZT/SBT thin films were completely composed of PZT and SBT, and no other secondary phase was observed. The electrical properties of the bilayered structure PZT/SBT films have been investigated in comparison with pure PZT and SBT films. PZT/SBT bilayered thin films showed larger remanent polarization (2P_r) of 18.37 μC/cm² than pure SBT and less polarization fatigue up to 1 × 10⁹ switching cycles than pure PZT. These results indicated that this bilayered structure of PZT/SBT is a promising material combination for ferroelectric memory applications.     

Photooxidation of different organic dyes (RB, MO, TB, and BG) using Fe(III)-doped TiO2 nanophotocatalyst prepared by novel chemical method

The nano-structured Fe(III)-doped TiO₂ photocatalysts with anatase phase have been developed for the oxidation of non-biodegradable different organic dyes like methyl orange (MO), rhodamine B (RB), thymol blue (TB) and bromocresol green (BG) using UV-Hg-lamp. The different compositions of Fe_xTi_1−xO₂ (x = 0.005, 0.01, 0.05, and 0.1) nanocatalysts synthesized by chemical method (CM), have been characterized by X-ray diffraction (XRD), UV-vis diffuse reflectance spectra, specific surface area (BET), transmission electronic microscopy (TEM) analysis, XPS, ESR and zeta potential. From XRD analysis, the results indicate that all the compositions of Fe(III) doped in TiO₂ catalysts gives only anatase phase not rutile phase. For complete degradation of all the solutions of the dyes (MO, RB, TB, and BG), the composition with x = 0.005 is more photoactive compared all other compositions of Fe_xTi_1−xO₂, and degussa P25. The decolorization rate of different dyes decreases as Fe(III) concentration in TiO₂ increases. The energy band gap of Fe(III)-doped TiO₂ is found to be 2.38 eV. The oxidation state of iron has been found to be 3+ from XPS and ESR show that Fe³⁺ is in low spin state.     

Design and fabrication of a TiO2/nano-silicon composite visible light photocatalyst

Nano-silicon (nc-Si) was utilized as the charges generator to promote the photocatalytic and super-hydrophilic reactivity of TiO₂ film under visible light irradiation. The photocatalytic ability of TiO₂/nc-Si composite photocatalyst was evaluated by a set of experiments to photodecompose 100 ppm methylene blue (MB) in aqueous solution. And the super-hydrophilic property was characterized by measuring the water droplet contacts angle, under visible light irradiation in atmospheric air and at room temperature. Under 100 mW/cm² visible light irradiation, the droplet contact angles were reduced to 0° within 4 h with nc-Si charge generator. Additionally, the rate constant of MB photo-degradation was promoted 6.6 times.     

Preparation, characterization and photocatalytic activity of polycrystalline Bi2O3/SrTiO3 composite powders

Bi₂O₃/SrTiO₃ composite powders have been prepared and their photocatalytic activities were investigated by photooxidation of methanol. These powders were characterized by UV-Visible diffuse reflectance spectra, SEM and X-ray diffraction (XRD). The results revealed that all the Bi₂O₃/SrTiO₃ composite powders exhibited higher photocatalytic activity than pure SrTiO₃, Bi₂O₃ and TiO₂ (P25) under visible light irradiation (λ>440 nm). The effects of the Bi₂O₃ contents on the photocatalytic activities of the composite powders were examined, the photocatalytic activities increased with the content of Bi₂O₃ increasing to a maximum of 83% and then decreased under visible light irradiation. The effects of the calcination temperatures on the photocatalytic activities of the composite powders were also investigated.