Adsorption and structural properties of channel-like and cage-like organosilicas

Channel-like and cage-like mesoporous silicas, SBA-15 (P6mm symmetry group) and SBA-16 (Im3m symmetry group), were modified by introducing single ureidopropyl surface groups, mixed ureidopropyl and mercaptopropyl surface groups, and single bis(propyl)disulfide bridging groups. These hexagonal and cubic organosilicas were prepared under acidic conditions via co-condensation of tetraethyl orthosilicate (TEOS) and proper organosilanes using poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) amphiphilic block copolymer templates, P123 (EO₂₀PO₇₀EO₂₀) and F127 (EO₁₀₆PO₇₀EO₁₀₆). The modified SBA-15 and SBA-16 materials were synthesized by varying the molar ratio of organosilane to TEOS in the initial synthesis gel. The removal of polymeric templates, P123 and F127, was performed with ethanol/hydrochloric acid solution. In the case of SBA-15 the P123 template was fully extracted, whereas this extraction process was less efficient for the removal of F127 template from the SBA-16-type organosilicas; in the latter case a small residue of F127 was retained. The adsorption and structural properties of the resulting materials were studied by nitrogen adsorption-desorption isotherms at −196^∘C (surface area, pore size distribution, pore volumes), powder X-Ray diffraction, CHNS elemental analysis and high-resolution thermogravimetry. The structural ordering, the BET specific surface area, pore volume and pore size decreased for both channel-like and cage-like mesoporous organosilicas with increasing concentration of incorporated organic groups.     

Synthesis of large-pore SBA-15 silica using poly(ethylene oxide)-poly(methyl acrylate) diblock copolymers

Poly(ethylene oxide)-poly(methyl acrylate) diblock copolymers with narrow molecular weight distributions were synthesized using atom transfer radical polymerization. The copolymers were used as micellar templates for the synthesis of mesoporous silicas. The products were characterized using small-angle X-ray scattering, transmission electron microscopy (TEM) and nitrogen adsorption. The obtained silicas exhibited two-dimensional hexagonal structures of cylindrical mesopores, and thus can be classified as SBA-15 silicas. In some cases, the size of ordered domains was very small. The (100) interplanar spacings were 13–17 nm, depending on the size of the diblock copolymer used and on the synthesis conditions. Nitrogen adsorption showed that the silicas exhibited specific surface areas of 350–800 m² g⁻¹, pore volumes ∼1 cm³ g⁻¹, and narrow pore size distributions. The BJH (nominal) pore diameters were up to ∼20 nm, but actual diameters of cylindrical pores are expected to be somewhat smaller. In many cases, the mesopores exhibited constrictions.     

Synthesis of FDU-1 silica with narrow pore size distribution and tailorable pore entrance size in the presence of sodium chloride

Ordered silicas with large (9-15 nm), uniform, cagelike mesopores were synthesized under acidic aqueous conditions from tetraethyl orthosilicate in the presence of sodium chloride using poly(ethylene oxide)-poly(butylene oxide)-poly(ethylene oxide) triblock copolymer B50-6600 (EO39BO47EO39, Dow Chemicals) as a supramolecular template. Except for the use of NaCl in our case, the synthesis mixture composition was the same as that originally reported by Zhao et al. for the synthesis of FDU-1 silica, which was later shown to exhibit a cubic close-packed (Fm3m) structure with stacking faults related to the occurrence of hexagonal close-packed stacking sequences. The copolymer-templated silicas were formed at room temperature and in most cases were subjected to the hydrothermal treatment at 373 or 393 K. The calcined materials were characterized using small-angle X-ray scattering (SAXS) and nitrogen and argon adsorption at 77 K. SAXS patterns were generally similar to those reported for FDU-1 silica, indicating the cubic close-packed (Fm3m) structure, but the presence of stacking faults characteristic of a hexagonal close-packed structure cannot be precluded. The addition of the salt was found to significantly narrow the pore size distributions and to improve the uniformity of entrances to the cagelike mesopores, whereas the pore diameter, specific surface area, and pore volume were similar (in most cases slightly lower) to those for FDU-1 silicas obtained in the absence of NaCl. The materials synthesized in the presence of NaCl also appeared to have better resolved SAXS patterns. The feasibility of tailoring the pore cage diameter (from approximately 9.5 to 14.5 nm) and pore entrance diameter (from below 4 to approximately 8 nm) simply by adjusting the hydrothermal treatment temperature and time was demonstrated, indicating that these simple and convenient ways of structural design of cagelike mesopores are operative in the case of syntheses in the presence of inorganic salts.     

Facile method to synthesize platelet SBA-15 silica with highly ordered large mesopores

Highly ordered mesoporous SBA-15 silica with large pore diameter of 18 nm (nominal BJH pore diameter ~22 nm) and short pore length (~500 nm) was synthesized using a micelle expander 1,3,5-triisopropylbenzene in the absence of ammonium fluoride by employing short initial stirring time at 17 °C followed by static aging at low temperature. Scanning and transmission electron microscopies revealed that the material comprised of platelet particles in which large mesopores were nearly flawlessly arranged within uniform domains up to 3 μm in size. The platelet SBA-15 had the (100) interplanar spacing of 17 nm, high surface area (~470 m(2) g(-1)) and large pore volume (~1.6 cm(3) g(-1)). The hydrothermal treatment at 130 °C for 2 days was employed to eliminate constrictions from the pore channels. The control experiment showed that a sample prepared with prolonged stirring had very similar mesoporous properties, but the particle size was smaller and the domains were irregular, proving that the static conditions facilitate the formation of SBA-15 with platelet particle morphology. The absence of ammonium fluoride was also critical in attaining the platelet particle shape.     

Ordered mesoporous silica with large cage-like pores: structural identification and pore connectivity design by controlling the synthesis temperature and time

FDU-1 silicas with large cage-like pores (diameter about 10 nm) were synthesized under acidic conditions from tetraethyl orthosilicate in the presence of a poly(ethylene oxide)-poly(butylene oxide)-poly(ethylene oxide) triblock copolymer template B50-6600 (EO(39)BO(47)EO(39)). High-resolution transmission electron microscopy and small-angle X-ray scattering provided strong evidence that FDU-1 silica synthesized under typical conditions is a face-centered cubic Fm3m structure with 3-dimensional hexagonal intergrowth and is not a body-centered cubic Im3m structure, as originally reported. Samples synthesized in a wide range of conditions (initial temperatures from 298 to 353 K; hydrothermal treatment at 333-393 K) exhibited similar XRD patterns and their nitrogen adsorption isotherms indicated a good-quality cage-like pore structure. The examination of low-pressure nitrogen adsorption isotherms for FDU-1 samples, whose pore entrance diameters were evaluated using an independent method, allowed us to conclude that low-pressure adsorption was appreciably stronger for samples with smaller pore entrance sizes. This prompted us to examine low-pressure adsorption isotherms for a wide range of samples and led us to a conclusion that the FDU-1 pore entrance size can be systematically enlarged from about 1.3 nm (perhaps even lower) to at least 2.4 nm without an appreciable loss of uniformity by increasing the temperature of the hydrothermal treatment or the initial synthesis. Further enlargement of pore entrance size was achieved for sufficiently long hydrothermal treatment times at temperatures of 373 K or higher, as seen from the shape of nitrogen desorption isotherms. This allowed us to obtain samples with uniform pore sizes, high adsorption capacity, and with pore entrances enlarged so much that their size was similar to the size of the pore itself, resulting in a highly open porous structure. However, in the latter case, there was evidence that the pore entrance size distribution was quite broad.     

Highly-controlled grafting of mono and dicationic 4,4'-bipyridine derivatives on SBA-15 for potential application as adsorbent of CuCl(2) from ethanol solution

Ultra-large-pore FDU-12 (ULP-FDU-12) silica with face-centered cubic structure (Fm3m type) of spherical mesopores was synthesized using Pluronic F127 triblock copolymer (EO(106)PO(70)EO(106)) and ethylbenzene as a new micelle expander at initial temperature of 14 °C. Ethylbenzene was identified on the basis of its reported extent of solubilization in poly(ethylene oxide)-poly(propylene oxide)-type surfactant micelles, which was similar to that of xylene, the latter having been shown earlier to afford ULP-FDU-12. The unit-cell parameter of as-synthesized ULP-FDU-12 was 55 nm, which is similar to the highest value reported when xylenes (mixture of isomers) were used and larger than that achieved with trimethylbenzene. The unit-cell parameter of calcined ULP-FDU-12 reached 52 nm. For the obtained materials, the nominal pore cage diameter calculated from nitrogen adsorption reached 32 nm, whereas the actual pore cage diameter calculated using the geometrical relation was 36 nm. The pore entrance size was below 5 nm before the acid treatment, but was greatly enlarged as a result of the treatment. The sample prepared without hydrothermal treatment was converted to ordered closed-pore silica at as low as 400-450 °C. Our study confirms the ability to select micelle expanders on the basis of data on solubilization of compounds in micelle solutions.     

Adsorption properties of ordered mesoporous silicas synthesized in the presence of block copolymer Pluronic F127 under microwave irradiation

Ordered mesoporous silicas (OMSs) were prepared at different temperatures by using tetraethyl orthosilicate (TEOS) as a silica source, poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymer (Pluronic F127) as a structure directing agent and sodium chloride as an additive under acidic conditions and microwave irradiation. The small angle X-ray diffraction patterns of these samples indicate the presence of ordered mesopores, while adsorption studies show that they possess high volumes of pores, bimodal pore size distributions and large pore sizes. There is an interesting change in the hysteresis loop of nitrogen adsorption isotherms with increasing temperature of hydrothermal treatment; a delayed desorption characteristic for cage-like mesostructures is observed for the OMS samples treated at 100 and 120?°C, while the hydrothermal treatment at 140 and 160?°C leads to the samples having hysteresis loops characteristic for channel-like materials.     

"Nanocasting": using SBA-15 silicas as hard templates to obtain ultrasmall monodispersed gamma-Fe2O3 nanoparticles

This work describes the use of mesoporous SBA-15 silicas as hard templates for the size-controlled synthesis of oxide nanoparticles, with the pores acting as nanoscale reactors. This fundamental work is mainly aimed at understanding unresolved issues concerning the occurrence and size dependence of phase transitions in oxide nanocrystals. Aqueous solutions of Fe(NO3)3*9H2O are deposited inside the pores of SBA-15 silicas with mesopore diameters of 4.3, 6.6, and 9.5 nm. By calcination, the nitrate salt transforms into FeOx oxides. The XRD peaks of nanocrystals are broad and overlapping, resulting in ambiguities attributed to a given allotropic variety of Fe2O3 (alpha, epsilon, or gamma) or Fe3O4. The association of XRD, SAED, and Raman information is necessary to solve these ambiguities. The metastable gamma-Fe2O3 variety is selectively formed at low Fe/Si atomic ratio (ca. 0.20) and when a low calcination temperature is used (773 or 873 K followed by quenching to room temperature once the targeted temperature is reached). The small size dispersion of the patterned nanoparticles, suggested on a local scale by TEM, is confirmed statistically by magnetic measurements. The nanoparticles have a superparamagnetic behavior around room temperature. Their magnetic moments (from 220 to 370 mB), their sizes (from 4.0 to 4.8 nm), and their blocking temperatures (from 36 to 58 K) increase with the silica template mesopore diameter. Their magnetic properties are compared to those of standard gamma-Fe2O3 nanoparticles of similar size, obtained by coprecipitation in water and stabilized by a citrate coating.     

Effect of pore structure in mesoporous silicas on VOC dynamic adsorption/desorption performance

The dynamic adsorption/desorption behavior of volatile organic compounds (VOCs) such as toluene (C7H8) and benzene (C6H6) was evaluated for three kinds of mesoporous silicas of SBA-15, all having almost the same mesopore size of ca. 5.7 nm, and a MCM-41 silica with a smaller pore size of 2.1 nm using a continuous three-step test. The fiberlike SBA-15 silica exhibited exceptionally good breakthrough behavior, a higher VOC capacity, and easier desorption. The fiberlike silica was composed through the catenation of rodlike particles. The rodlike silicas, by comparison, were proven to be less useful in dynamic adsorption processes because of lower dynamic VOC capacities despite having comparative porous parameters with the fiberlike silica. The large dynamic VOC capacity of the fiberlike silica was attributed to the presence of a bimodal pore system consisting of longer, one-dimensional mesopore channels connected by complementary micropores.     

A family of ordered mesoporous carbons derived from mesophase pitch using ordered mesoporous silicas as templates

A variety of ordered mesoporous carbons (OMCs) were synthesized using ordered mesoporous silicas (OMSs) as hard templates and the mesophase pitch (MP) as a carbon precursor. The synthesis included the mixing of OMS with MP, the infiltration of OMS with MP at 450–550?°C and the carbonization of MP in OMS/MP composite followed by the dissolution of the OMS template. OMCs with structures of two-dimensional hexagonal arrays of nanorods and three-dimensional arrays of nanospheres were obtained through the replication of silica templates, including large-pore SBA-15, KIT-6, large-pore FDU-12 and SBA-16. In particular, 2-D hexagonal array of carbon nanorods (CMK-3 carbon) with (100) interplanar spacing of ～13 nm as well as an array of carbon nanospheres arranged in the face-centered cubic structure with the unit-cell parameter of 33 nm were successfully prepared. The specific surface areas of the resulting carbons were up to 400 m²/g, and the total pore volumes were up to 0.43 cm³/g, with the highest values achieved when the MP infiltration temperature was 500?°C. The OMCs exhibited narrow mesopore size distributions. As inferred from XRD, the frameworks of OMCs featured semi-graphitic structures even though moderate carbonization temperature (850?°C) was employed.     

Mechanism of freezing of water in contact with mesoporous silicas MCM-41, SBA-15 and SBA-16: role of boundary water of pore outlets in freezing

The freezing mechanism of water contacted with mesoporous silicas with uniform pore shapes, both cylindrical and cagelike, was studied by thermodynamic and structural analyses with differential scanning calorimetry (DSC) and X-ray diffraction (XRD) together with adsorption measurements. In the DSC data extra exothermic peaks were found at around 230 K for water confined in SBA-15, in addition to that due to the freezing of pore water. These peaks are most likely to be ascribed to the freezing of water present over the micropore and/or mesopore outlets of coronas in SBA-15. Freezing of water confined in SBA-16 was systematically analysed by DSC with changing the pore size. The freezing temperature was found to be around 232 K, close to the homogeneous nucleation temperature of bulk water, independent of the pore size when the pore diameter (d) < 7.0 nm. Water confined in the cagelike pores of SBA-16 is probably surrounded by a water layer (boundary water) at the outlets of channels to interconnect the pores and of fine corona-like pores, which is similar to that present at the outlet of cylindrical pores in MCM-41 and of cylindrical channels in SBA-15. The presence of the boundary water would be a key for water in SBA-16 to freeze at the homogeneous nucleation temperature. This phenomenon is similar to those well known for water droplets in oil and water droplets of clouds in the sky. The XRD data showed that the cubic ice I(c) was formed in SBA-16 as previously found in SBA-15 when d < 8.0 nm.     

Mechanism for the formation of tin oxide nanoparticles and nanowires inside the mesopores of SBA-15

The formation of polycrystalline tin oxide nanoparticles (NP) and nanowires was investigated using nanocasting approach included solid-liquid strategy for insertion of SnCl₂ precursor and SBA-15 silica as a hard template. HR-TEM and XRD revealed that during the thermal treatment in air 5 nm tin oxide NP with well defined Cassiterite structure were formed inside the SBA-15 matrix mesopores at 250 °C. After air calcination at 700 °C the NP assembled inside the SBA-15 mesopores as polycrystalline nanorods with different orientation of atomic layers in jointed nanocrystals. It was found that the structure silanols of silica matrix play a vital role in creating the tin oxide NP at low temperature. The pure tin chloride heated in air at 250 °C did not react with oxygen to yield tin oxide. Tin oxide NP were also formed during the thermal treatment of the tin chloride loaded SBA-15 in helium atmosphere at 250 °C. Hence, it is well evident that silanols present in the silica matrix not only increase the wetting of tin chloride over the surface of SBA-15 favoring its penetration to the matrix pores, but also react with hydrated tin chloride according to the proposed scheme to give tin oxide inside the mesopores. It was confirmed by XRD, N₂-adsorption, TGA-DSC and FTIR spectra. This phenomenon was further corroborated by detecting the inhibition of SnO₂ NP formation at 250 °C after inserting the tin precursor to SBA-15 with reduced silanols concentration partially grafted with tin chloride.     

Towerlike SBA-15: base and (10)-specific coalescence of a silicate-encased hexagonal mesophase tailored by nonionic triblock copolymers

Hydrothermal templating of mesoporous molecular sieves by nonionic triblock copolymers [poly(oxyethylene)-poly(oxypropylene)-poly(oxyethylene) (PEO-PPO-PEO)] at specific block lengths of EO(20)PO(70)EO(20) and selected 2 M HCl dosage (pH -0.3) caused the formation of micrometer-sized SBA-15 hexagons with well-ordered hexagonal pore channels (pore size and wall thickness of approximately 6 nm and pore-to-pore distance of approximately 12 nm) after template removal. For a beneficial lower surface energy, these {10} laterally coalesced hexagons tend to stack imperfectly over the base into towerlike entities, leaving dislocations and faults within the single domain thus formed. Evidence for the mechanism of Brownian motion/coalescence of the hexagonal-mesophase particulates, previously suggested for MCM-41 accretion in the presence of cationic surfactant, is more clearly identifiable in the present low-pH case of amphiphilic block copolymer templates and linear silica oligomers.     

Understanding effect of wall structure on the hydrothermal stability of mesostructured silica SBA-15

Mesostructured silica SBA-15 materials with different structural parameters, such as pore size, pore volume, and wall thickness, etc., were prepared by varying the postsynthesis hydrothermal treatment temperature and adding inorganic salts. The hydrothermal stabilities of these materials in steam (100% water vapor) were systematically investigated using a variety of techniques including powder X-ray diffraction, transmission electron microscopy, nitrogen sorption, and (29)Si solid-state NMR. The effect of the pore size, microporosity or mesoporosity, and wall thickness on the stability was discussed. The results show that all of the SBA-15 materials have a good hydrothermal stability under steam of 600 degrees C for at least 24 h. N(2) sorption measurements show that the Brumauer-Emmett-Teller surface area of SBA-15 materials is decreased by about 62% after treatment under steam at 600 degrees C for 24 h. The materials with thicker walls and more micropores show relatively better hydrothermal stability in steam of 600 degrees C. Interestingly, we found that the microporosity of the mesostructured silica SBA-15 is a very important factor for the hydrothermal stability. To the materials with more micropores, the recombination of Si-O-Si bonds during the high-temperature steam treatment may not cause direct destruction to the wall structure. As a result, SBA-15 materials with more micropores show better stability in pure steam of 600 degrees C. Nevertheless, these materials are easily destroyed in steam of 800 degrees C for 6 h. Two methods to effectively improve the hydrothermal stability are introduced here: one is a high-temperature treatment, and another is a carbon-propping thermal treatment. Thermal treatment at 900 degrees C can enhance the polymerization degree of Si-O-Si bonds and effectively improve the hydrothermal stability of these SBA-15 materials in 800 degrees C steam for 12 h. But, this approach will cause very serious shrinkage of the mesopores, resulting in smaller pore diameter and low surface area. A carbon-propping thermal treating method was employed to enhance the polymerization of Si-O-Si bonds and minimize the serious shrinkage of mesopores at the same time. It was demonstrated to be an effective method that can greatly improve the hydrothermal stability of SBA-15 materials in 800 degrees C steam for 12 h. Furthermore, the SBA-15 materials obtained by using the carbon-propping method possess larger pores and higher surface area after the steam treatment at 800 degrees C compared to the materials from the direct thermal treatment method after the steam treatment.     

Improvement of the Kruk-Jaroniec-Sayari method for pore size analysis of ordered silicas with cylindrical mesopores

In this work, the X-ray diffraction structure modeling was employed for analysis of hexagonally ordered large-pore silicas, SBA-15, to determine their pore width independently of adsorption measurements. Nitrogen adsorption isotherms were used to evaluate the relative pressure of capillary condensation in cylindrical mesopores of these materials. This approach allowed us to extend the original Kruk-Jaroniec-Sayari (KJS) relation (Langmuir 1997, 13, 6267) between the pore width and capillary condensation pressure up to 10 nm instead of previously established range from 2 to 6.5 nm for a series of MCM-41 and to improve the KJS pore size analysis of large pore silicas.     

介孔氧化硅孔径尺寸对Eu(Ⅲ)配合物的影响

分别以十六烷基三甲基溴化铵(CTAB)和聚乙氧基-聚丙氧基-聚乙氧基三嵌段共聚物(P123)为模板剂、正硅酸乙酯(TEOS)为硅源，采用水热法合成了有序介孔分子筛MCM-41和SBA-15。选择Eu(DBM)₃phen为客体，有序介孔氧化硅MCM-41和SBA-15为载体，分别在氯仿中进行分子组装，制备出具有较强发光性能的介孔复合材料Eu(DBM)₃phen/APTES-MCM-41(EAM)和Eu(DBM)₃phen/APTES-SBA-15(EAS)。采用XRD、TEM、N₂吸附-脱附和荧光光谱等对产物的结构与性能进行了分析。结果表明，Eu(DBM)₃phen组装进有序介孔氧化硅的孔道中后，发光纯度提高。而且孔径越小，发光纯度越高。选用较大孔径的SBA-15为载体，在不显著影响发光纯度的同时，可以获得较高的发光强度。     

Epoxy-functionalized large-pore SBA-15 and KIT-6 as affinity chromatography supports

Mesoporous silica supports are proposed as an alternative to polymeric stationary phases for fast affinity chromatography due to their better mechanical strength compared to polymers. Ideal supports should combine high surface area and large pore size to allow a high loading capacity of large molecules, such as proteins, and favor their accessibility. Increasing the pore size of large-surface area micelle-templated silicas (SBA-15, KIT-6) has been achieved by swelling the micelles by the addition of organic molecules and increasing synthesis time and temperature. The pore size of hexagonal silica mesostructured SBA-15 has been increased up to 35 nm. These materials could find therefore application as affinity chromatography for immunoextraction.     

Pyrolysis of mesoporous silica-immobilized 1,3-diphenylpropane. Impact of pore confinement and size

Mesoporous silicas such as SBA-15 and MCM-41 are being actively investigated for potential applications in catalysis, separations, and synthesis of nanostructured materials. A new method for functionalizing these mesoporous silicas with aromatic phenols is described. The resulting novel hybrid materials possess silyl aryl ether linkages to the silica surface that are thermally stable to ca. 550 degrees C, but can be easily cleaved at room temperature with aqueous base for quantitative recovery of the organic moieties. The materials have been characterized by nitrogen physisorption, FTIR, NMR, and quantitative analysis of surface coverages. The maximum densities of 1,3-diphenylpropane (DPP) molecules that could be grafted to the surface were less than those measured on a nonporous, fumed silica (Cabosil) and were also found to decrease as a function of decreasing pore size (5.6-1.7 nm). This is a consequence of steric congestion in the pores that is magnified at the smaller pore sizes, consistent with parallel studies conducted using a conventional silylating reagent, 1,1,3,3-tetramethyldisilazane. Pyrolysis of the silica-immobilized DPP revealed that pore confinement leads to enhanced rates and altered product selectivity for this free-radical reaction compared with the nonporous silica, and the rates and selectivities also depended on pore size. The influence of confinement is discussed in terms of enhanced encounter frequencies for bimolecular reaction steps and pore surface curvature that alters the accessibility and resultant selectivity for hydrogen transfer steps.     

Periodic mesoporous organosilicas with multiple bridging groups and spherical morphology

Bi- and trifunctional periodic mesoporous organosilicas (PMOs) with phenylene, thiophene, and ethane bridging groups were synthesized using 1,2-bis(triethoxysilyl)ethane (BTEE), 1,4-bis(triethoxysilyl)benzene (BTEB), and 2,5-bis(triethoxysilyl)thiophene (BTET) organosilica precursors and a poly(ethylene oxide)-poly(D,L-lactic acid-co-glycolic acid)-poly(ethylene oxide) (PEO-PLGA-PEO) triblock copolymer template under low acidic conditions. The PMO samples with different concentrations of organic bridging groups were obtained in the form of spherical particles having average diameters of 2-3 mum and 2D hexagonal (p6m) mesostructure with pore diameters of 7.3-8.4 nm. The particle morphology and chemistry of pore walls were tailored using different mixtures of organosilica precursors. Adsorption and structural properties of the aforementioned PMOs have been studied by nitrogen adsorption and small-angle X-ray scattering, whereas their framework chemistry was quantitatively analyzed by solid-state 13C and 29Si MAS NMR.     

Synthesis of chiral mesoporous silicas with oligo(saccharide) surfaces and their use in separation of stereoisomers

Novel chiral mesoporous silicas (SBA-15 motif) with chemically bonded oligo(saccharides) (1, 3, and 7 glucose units) were obtained through the cocondensation of organosilicon derivatives of the oligo(saccharides) and silica precursors in the presence of polymer surfactant template under mild acidic conditions. The pore order and structure of the materials prepared were characterized by transmission electron microscopy and nitrogen adsorption. The direct application of the oligo(saccharide)-grafted SBA-15 stationary phases in the HPLC separations of stereoisomers was demonstrated for the first time.