CMC和CTAB双模板法合成具有稳定结构的MCM-41中孔分子筛

以羧甲基纤维素和十六烷基三甲基溴化铵为双模板,制备出了具有更高稳定性并且具有高度有序二维六方结构的MCM-41介孔分子筛.透射电镜和X射线衍射结果表明,以双模板制备的MCM-41介孔分子筛具有高度有序的二维六方(p6mm)孔道结构.此外,以双模板制备的MCM-41介孔分子筛焙烧前后的X射线衍射结果表明,在焙烧过程中其晶胞收缩比例为3.1%.与以纯表面活性剂为模版制备的MCM-41介孔分子筛(晶胞收缩比例为9.7%)相比,双模板制备的MCM-41介孔分子筛具有更高的稳定性能. MCM-41介孔分子筛稳定性能的提高可能是由于在硅物种、表面活性剂以及羧甲基纤维素在自组装过程中,羧甲基纤维素表面丰富的羟基与硅物种Si-(OH)x的相互作用促进了Si-(OH)x的缩聚.     

(Dy,Mn)MCM-41介孔分子筛的合成与表征

在碱性条件下, 以十六烷基三甲基溴化铵为模板剂, Na2Si3O7为硅源, 用水热法合成了双金属介孔分子筛(Dy, Mn)MCM-41. 并用XRD, FT-IR, SEM, X射线荧光分析法、紫外漫反射等对样品进行表征. 实验结果证实所合成的产物为(Dy,Mn)MCM-41.     

Pd/NH2C3H6-MCM-41催化水介质中的碘苯Ullmann反应

 采用室温共缩聚法合成了胺基改性MCM-41杂化材料(NH2C3H6-MCM-41), 并以此材料为载体制备了负载型Pd催化剂 (Pd/NH2C3H6-MCM-41). 采用X射线衍射、核磁共振、红外光谱、透射电镜、X射线光电子能谱和N2吸附等方法对催化剂进行了表征. 结果表明,催化剂仍保持有MCM-41的孔结构,但其有序度随着 NH2C3H6-基团和Pd含量的增加而降低. 催化剂在以水为溶剂的碘苯偶联反应(Ullmann反应)中显示出优良的催化性能,联苯收率可达63%, 有望为清洁有机合成提供高效非均相催化剂. 胺基修饰的促进作用可归因于催化剂Pd分散度的提高和表面化学性质的改变.     

纳米MCM-41组装DBC-偶氮胂的研究

以纳米MCM-41孔道为模版,组装制备了二溴对氯偶氮胂(DBC-ASA)纳米簇合物。采用化学分析、粉末X-射线衍射、77 K N2吸附-解吸附、红外光谱、固体扩散漫反射光谱及发光光谱表征了制备的(MCM-41)-(DBC-ASA)主-客体纳米复合材料。结果表明,DBC-ASA成功地组装在了主体MCM-41中,并且处于主体分子筛材料的纳米孔道中。(MCM-41)-(DBC-ASA)纳米复合材料具有作为发光材料的应用前景。     

以CTMABr和CTMAOH为共模板剂合成MCM-41

采用共模板剂水热合成了MCM-41.分别用X射线粉末衍射(XRD)、固体核磁共振(²⁷AlMASNMR)和N₂吸附等温线技术考察了用该方法和传统方法所制备的Si-MCM-41和Al-MCM-41样品的晶相结构、孔结构以及Al在分子筛中的化学环境.结果表明,用共模板剂方法合成的MCM-41样品,其纯度和孔径均一性显著提高,特别是当样品中Al含量较高时,仍可保证Al原子以四配位结合在MCM-41的硅骨架上.还就采用共模板剂的理论依据进行了讨论.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

Pt对Ni2P/MCM-41催化剂加氢脱硫性能的影响

以MCM-41为载体, 采用程序升温还原法制备了含有少量Pt的Ni-P/MCM-41催化剂, 并用氢气程序升温还原(H₂-TPR)、 X射线衍射(XRD)、 N₂吸附比表面积、 X射线光电子能谱(XPS)和透射电子显微镜(TEM)对催化剂的结构和性能进行了表征. 考察了P/Ni摩尔比及Pt含量对Ni-P/MCM-41催化剂催化二苯并噻吩(DBT)加氢脱硫(HDS)性能的影响. 结果表明, Pt能降低Ni₂P催化剂的还原温度, 并有助于Ni₂P相的生成, 抑制团聚现象, 提高催化剂的HDS活性. 当Pt的质量分数为0.6%, P/Ni摩尔比为2时, 催化剂具有最佳加氢脱硫活性, 在340 ℃, 3.0 MPa, 氢油体积比为500, 质量空速(WHSV)为2.0 h^-1的条件下, 二苯并噻吩转化率为100%, 且催化剂加氢脱硫活性在120 h内基本保持稳定.     

Pt-Al/MCM-41催化剂的制备及催化合成有机硅增效剂

以介孔硅MCM-41为载体,Al Cl_3为促进剂,制备了负载型Pt-Al/MCM-41催化剂。利用傅里叶红外光谱(FTIR)、N_2吸附-脱附、X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、电感耦合等离子体发射光谱(ICP)对催化剂的结构、形貌以及金属间作用力进行了表征,着重探讨了不同Al加入量对催化剂结构和金属间作用力的影响,系统考察了Pt-Al/MCM-41用于催化聚乙二醇烯丙基醚和七甲基三硅氧烷合成有机硅增效剂。结果表明,Al的加入量对催化剂的结构和有序度有一定的影响,其比表面积、孔容和有序度随着Al用量的增加而逐步降低。此外,加入一定量的Al有利于提高Pt晶粒的分散度,减小其粒径。Pt_1Al_2/MCM-41催化剂具有良好的重复使用性,使用6次无明显失活,其转化率仍大于90%。合成有机硅增效剂的最佳工艺为:n_(PGAE)/n_(MDHM)=1.1,反应时间为4 h,反应温度为100℃,催化剂用量为0.5%,其转化率达94.1%。     

Co掺杂ZnO/MCM-41分子筛的制备及对异戊醇的催化氧化性能

以Co掺杂的介孔分子筛MCM-41为载体, 采用等体积浸渍法制备了系列5%ZnO/xCo-MCM-41催化剂, 并用于催化分子氧氧化异戊醇合成异戊醛的反应. 通过X射线衍射(XRD), 傅里叶变换红外光谱(FTIR), 紫外-可见漫反射光谱(UV-Vis DRS), 扫描电子显微镜(SEM), 氨气程序升温脱附(NH₃-TPD), 氢气程序升温还原(H₂-TPR)和氮气吸附-脱附等手段对样品进行表征, 并考察了Co掺杂量对分子筛结构和催化性能的影响. 结果表明, 随着Co掺杂量的增大, 样品的比表面积和孔体积均减小, 而其平均孔径呈先增大后减小的趋势. 当Co掺杂量为0.05时, 5%ZnO/0.05Co-MCM-41仍保持了MCM-41高度有序的六方介孔结构, 具有高比表面积(989 m²/g)、较大孔径(2.88 nm)和孔体积(0.88 cm³/g), 引入的Co主要以孤立态钴离子[Single-site Co(Ⅱ)]形式存在于MCM-41骨架, MCM-41骨架中的Co可以有效提高ZnO微粒的分散度, 适度降低5%ZnO/MCM-41的表面酸性, 并大幅度提高5%ZnO/MCM-41的氧化还原性. 与5%ZnO/MCM-41相比, 5%ZnO/0.05Co-MCM-41可使异戊醛的选择性提高28.3%.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶.凝胶法将TiO2担载在介孔MCM-41分子筛上,制备了不同TiO2含量的系列TiO2/MCM-41复合材料,利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征.TiO2的晶型为锐钛矿相,复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小,TiO2的平均粒径随其担载量的增加而增大.以罗丹明B的光催化降解为探针反应,评价了TiO2/MCM-41复合材料的光催化降解活性.结果表明,在紫外光照射下,罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学,复合材料对罗丹明B的光催化降解活性明显高于商用TiO2(P-25),复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

Evidence of nanoconfinement effects of MCM-41 on propylene polymerization catalyzed by MCM-41 supported metallocene catalyst in the presence and absence of beta-cyclodextrin

Propylene polymerization was carried out with MCM-41 supported rac-Et(Ind)2ZrCl2 catalysts, in the presence and absence of beta-cyclodextrin. The resultant PP was studied by X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, and differential scanning calorimetry. Through comparison of the results, it was found that the channels of MCM-41 could act as a nanoreactor of propylene polymerization and the polypropylene (PP) contained in the channels had noncrystal structure. However, the PP could grow out of the channels and form some crystals after the active sites on the surface of MCM-41 were destroyed. This showed that the channels of MCM-41 had great confinement effects on propylene polymerization.     

镍(II)配合物官能化的MCM-41催化分子氧环氧化苯乙烯

制备了镍(II)席夫碱配合物官能化的MCM-41多相催化剂MCM-41-Ni.利用X射线粉末衍射、氮气物理吸附脱附、红外光谱、热重、电感耦合等离子体原子发射光谱、元素分析和透射电镜等方法对催化剂进行了表征.以氧气为氧化剂,MCM-41-Ni在催化环氧化苯乙烯的反应中表现出较高的催化活性;苯乙烯的转化率为95.2%,环氧苯乙烷的选择性为66.7%.系统地研究了反应温度、催化剂用量、溶剂以及反应时间对反应性能的影响.催化剂经过4次循环仍然表现出较好的稳定性和催化活性.     

Synthesis of MCM-41 supported amino-palladium complex and its catalytic performance for heck reaction

Using MCM-41 as the supporter, a series of MCM-41 supported amino-palladium complexes has been prepared and characterized by XRD (X-ray diffraction) and XPS (X-ray photoelectron spectroscopy), etc. The XRD and XPS results indicate that the Pd coordinates with the -NH₂ groups on the MCM-41 surface, and the structure of MCM-41 has been not damaged. Its catalytic performance for Heck arylation of alkene with aryl iodide shows that the catalysts have high activity and stereoselectivity in 70–90°C. The product of Heck reaction is in E form. And the effect of the preparation condition of catalyst on the catalytic performance was examined. Translated form Chinese Journal of Organic Chemistry, 2008, 28(5) (in Chinese)     

负载型磷化镍催化剂的空气表面改性法制备及其加氢脱氧性能

以MCM-41为载体,采用先前驱体氢气低温(673 K)还原、空气表面改性的方法制备了高活性的Ni2P/M CM-41催化剂,并采用XRD、BET、SEM、TEM、XPS和CO吸附等手段对催化剂进行了表征。以苯并呋喃(BF)加氢脱氧(HDO)为探针反应,考察了空气表面改性对Ni2P/M CM-41催化剂结构和HDO性能的影响。结果表明,空气表面改性得到的催化剂,活性相为单一的Ni2P;空气表面改性能够降低催化剂表面P物种的集聚,有助于小尺寸、高分散的Ni2P活性相的生成。在573 K、3.0 M Pa、质量空速为4.0 h-1、H2/油体积比为500的条件下,Ni2P/M CM-41催化剂上BF转脱氧产物收率高达88%,较程序升温还原法制备的催化剂高50%。     

A Novel Method for the Synthesis of Mesoporous Molecular Sieve MCM-41

Using glycerol, glycol and water as solvent, cetyltrimethylammonium bromide (CTAB) as template, tetraethyl orthosilicate (TEOS) as silica source, ethylenediamine (EDA) as base source, mesoporous molecular sieve MCM-41 has been synthesized at room temperature, characterized by X-ray power diffraction and N2 adsorption. Compared with the samples synthesized by glycol and water, the samples synthesized by glycerol have larger pore diameter and high surface areas. Thus glycerol is an efficient solvent for preparing larger pore mesoporous MCM-41.     

Influence of the pore structure of MCM-41 and SBA-15 silica fibers on atomic layer chemical vapor deposition of cobalt carbonyl

Mesoporous high surface area MCM-41 and SBA-15 type silica materials with fibrous morphology were synthesized and used as support materials for the ALCVD (atomic layer chemical vapor deposition) preparation of Co/MCM-41 and Co/SBA-15 catalysts. Co/MCM-41 and Co/SBA-15 catalysts were prepared by deposition of Co2(CO)8 from the gas phase onto the surfaces of preheated support materials in a fluidized bed reactor. For both silica materials, two different kinds of preparation methods, direct deposition and a pulse deposition method, were used. Pure silica supports as well as supported cobalt catalysts were characterized by various spectroscopic (IR) and analytical (X-ray diffraction, Brunauer-Emmett-Teller, elemental analysis) methods. MCM-41 and SBA-15 fibers showed considerable ability to adsorb Co2(CO)8 from the gas phase. For MCM-41 and SBA-15 silicas, cobalt loadings of 13.7 and 12.1 wt % were obtained using the direct deposition method. The cobalt loadings increased to 23.0 and 20.7 wt % for MCM-41 and SBA-15 silicas, respectively, when the pulse deposition method was used. The reduction behavior of silica-supported cobalt catalysts was found to depend on the catalyst preparation method and on the mesoporous structure of the support material. Almost identical reduction properties of SBA-15-supported catalysts prepared by different deposition methods are explained by the structural properties of the mesoporous support and, in particular, by the chemical structure of the inner surfaces and walls of the mesopores. Pulse O2/H2 chemisorption experiments showed catalytically promising redox properties and surface stability of the prepared MCM-41- and SBA-15-supported cobalt catalysts.     

Readily accessible mesoporous silica nanoparticles supported chiral urea-amine bifunctional catalysts for enantioselective reactions

The main objective of this study is to develop readily accessible and recyclable solid catalysts for enantioselective reactions. To achieve this, magnetic MCM-41 and non-magnetic SBA-15 mesoporous supports were prepared, then mesoporous silica supported chiral urea-amine bifunctional catalysts were synthesized by grafting of chiral urea-amine ligand onto SBA-15 and magnetic MCM-41. The magnetic and non-magnetic supports and so-prepared solid catalysts were characterized by using different methods such as N₂ sorption measurements, Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscope-energy dispersive X-ray analysis (FESEM-EDX), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Results showed that (1R, 2R) or (1S, 2S)-1,2-diphenylethane-1,2-diamine was successively immobilized onto magnetic MCM-41 and SBA-15 pores. The heterogeneous chiral solid catalysts and their homogenous counterparts exhibited high activities both enantioselective transfer hydrogenation reaction (up to 99% conversion and 65% ee) and enantioselective Michael reaction (up to 98% conversion and 26% ee). Moreover, the SBA-15 supported solid catalysts were separated from the reaction mixture by simple filtration, whereas the magnetic MCM-41 supported solid catalysts were separated by simple magnetic decantation and reused in three consecutive catalytic experiments.     

PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价, 并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3, PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能. 发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性. 实验结果表明, 纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原, 导致铂金属分散度和催化剂的丙烷脱氢活性较低. 用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用, 提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性. 并且, 积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度, 故具有较高的丙烷脱氢反应稳定性. PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能可能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关, 而且与Al2O3/MCM-41载体的介孔结构有关.     

Preparation, characterization and optical properties of lanthanum-(nanometer MCM-41) composite material

Nanometer MCM-41 molecular sieve was prepared under a base condition by using cetyltrimethylammonium bromide as template and tetraethyl orthosilicate as silica source by means of hydrothermal method. Lanthanum(III) was incorporated into the nanometer MCM-41 by a liquid phase grafting method. The prepared nanocomposite materials were characterized by means of powder X-ray diffraction, spectrophotometric anaylsis, Fourier transform infrared spectroscopy, low temperature nitrogen adsorption-desorption technique, solid diffuse reflectance absorption spectra and luminescence. The powder X-ray diffraction studies show that the nanometer MCM-41 molecular sieve is successfully prepared. The highly ordered mesoporous two-dimensional hexagonal channel structure and framework of the support MCM-41 is retained intact in the prepared composite material La-(nanometer MCM-41). The spectrophotometric anaylsis indicates that lanthanum exists in the prepared nanocomposite materials. The Fourier transform infrared spectra indicate that the framework of the MCM-41 molecular sieve still remains in the prepared nanocomposite materials and some framework vibration peaks show blue shifts relative to those of the MCM-41 molecular sieve. The low temperature nitrogen adsorption-desorption indicates that the guest locates in the channel of the molecular sieve. Compared with bulk lanthanum oxide, the guest in the channel of the molecular sieve has smaller particle size and shows a significant blue shift of optical absorption band in solid diffuse reflectance absorption spectra. The observed blue shift in the solid state diffuse reflectance absorption spectra of the lanthanum-(nanometer MCM-41) sample show the obvious stereoscopic confinement effect of the channel of the host on the guest, which further indicates the successful encapsulation of the guest in the host. The La-(nanometer MCM-41) sample shows luminescence.