二阶导数光度法同时测定微量镍和铜的研究

用２－（２－噻唑偶氮）－５－二甲氨基苯甲酸作为显色剂，在ｐＨ５．６，波长在６２０ｎｍ和５９０ｎｍ处，用于阶导数光度法，同时测定微量镍和铜。回收率镍为１００％￣１０２％，铜在９２％￣１０５％，Ｎｉ＾２＋、Ｃｕ＾２＋在０￣１６μｇ／２５ｍｌ均呈线性关系。     

硫化物的快速分光光度法测定

提出了测定微量硫化物的快速亚甲蓝分光光度法，实验结果表明，在硫酸溶液中，Ｋ２Ｃｒ２Ｏ７＋对二甲氨基苯胺＋Ｓ＾－２迅速显色反应形成亚甲蓝，表现摩尔吸收系数为４．０６×１０＾４Ｌ．ｍｏｌ＾－１．ｃｍ＾－１；最大吸收波长为６６４ｎｍ；线性范围为０～０．８ｍｇ／Ｌ，实验了采用全差示光度法直接测定水中硫化物的条件，用于某江水中２１．６μｇ／Ｌ硫化物测定时，相对标准偏差为３．２％（ｎ＝６）；试样的标准加入回收     

间氯偶氮安替比林流动注射分析测定药物及水中钙

基于间氯偶氮安替比林可与钙在碱性介质中形成灵敏的兰色络合物这一显色反应，本文在自行组装的带微型计算机的流动注射分析仪上，以分光光度计作检测器，建立了测定微量钙的流动注射分光光度法。最佳显色反应条件：０．０８ｍｏｌ／Ｌ ＮａＯＨ－０．０１２％显色剂２．０％三乙醇胺溶液，测定波长为６３０ｎｍ。以三乙醇胺为掩蔽剂，方法选择性较高。钙的线性范围为１．０￣１５．０μｇ／ｍｌ，检测限０．５μｇ／ｍｌ，进样频率     

荧光光度法测定环境水中微量甲基对硫磷

研究了荧光分光光度法测定环境水中甲基对硫磷的一。在吲哚丙酮溶液０．２５％，过硼酸钠溶液０．２５％溶液中，温度５℃、λｅｘ／λｅｍ＝４１０ｎｍ／４９０ｎｍ，检出限５．０（５．２）μｇ／Ｌ，线性范围０－２．０（２．６）ｍｇ／Ｌ，回收率达９８－１０２％，结果满意。     

卡尔曼滤波析相光度法同时测定锰铁铜锌镉的研究——5—Br—PA…

运用卡尔曼滤波递推法，以２－（５－溴－２－吡啶偶氮）－５－二乙氨基苯酚（５－Ｂｒ－ＰＡＤＡＰ）为显色剂，建立了同时测定锰，铁，铜，锌，镉析相光度法，在ｐＨ９．０硼酸－氢氧化钠介质中，胶束溶液在９５℃加热１ｈ，配合物被ＴｒｉｔｏｎＸ－１００相完全富集，最大吸收峰分别为锰５６６ｎｍ，铁５５６ｎｍ，铜５６０ｎｍ锌５６２ｎｍ镉５５７ｎｍ，工作曲线范围除镉为０～８μｇ／５ｍｌ外，其余均为０～１０μｇ／５ｍｌ     

双波长分光光度法同时测定贵金属钯和锇

本文提出了在对羟基苯基荧光酮和溴化十六烷基三甲烷基甲胺存在下，双波长分光光度法同时测定微量和锇的新方法，在ｐＨ＝７．６～８．０的磷酸盐介质中，钯和锇的对羟基苯基荧光酮－ＣＴＭＡＢ配合物吸收光谱相互重叠，选择测定钯配合物的波长对为５８０．５ｎｍ与５３０．５ｎｍ，测定锇配合物的波长对为５５３．５ｎｍ与６０４．５ｎｍ，钯含量在０～７．０μｇ／１０ｍＬ范围内，锇含量在０～９．０μｇ／ｍＬ范围内，与ΔＡ值呈     

荧光光度法直接测定环境水中苯酚和十二烷基苯磺酸钠的含量

本文研究了用荧光分光光度法直接测定环境水中苯酚和十二烷基苯磺酸钠（ＳＤＢＳ）二种水中污染物。在ｐＨ〉１１直接测定ＳＤＢＳ含量，波长为λｅｘ／λｅｍ＝２３０／２９５ｎｍ，检出限４．４ｎｇ／ｍＬ，线性范围０￣２．２μｇ／ｍｌ。在ｐＨ＝６，波长为λｅｘ／λｅｍ＝２３０／２９５ｎｍ，测得二者合量，从合量中减去ＳＤＢＳ含量即得苯酚含量，检出限４．０ｎｇ／ｍｌ，线性范围０￣０．８５μｇ／ｍＬ，回收率达９９％￣     

双显色剂双波长系数补偿法同时测定铝和铁的研究

本文提出了一种双显色双波长系数补偿法测定食品中微量铝、铁的新方法，在ｐＨ＝６．２缓冲液中，以络天青Ｓ为显色剂选择６２２／５０６ｎｍ波长对测定铝，以５－Ｂｒ－ＰＡＤＡＰ为显色剂选择５６０／６６０ｎｍ波长对测定铁，不经分离可直接测定样品中的铝、铁，铝量在０．２～５．０μｇ／２５ｍｌ、铁量在１．０～１５．０μｇ／２５ｍｌ符合朗伯比耳定律。本法应用于食品中铝、铁测定，得到较满意结果。     

一阶导数吸光光度法同时测定纯硅中铁和铝的研究

提出了用一阶导数光光度法同时测定铁和铝的方法，在ｐＨ６．５乙二胺缓冲溶液中，乳化剂ＯＰ存在下，Ｆｅ＾３＋Ａｌ＾３＋与络天青Ｓ形成Ｆｅ＾３＋，Ａｌ＾３＋－ＣＡＳ－ＯＰ三元络合物，络合物一阶导数光谱等吸收点分别在６０６．２，６３８．０ｎｍ记录混合体系在两波长处一阶导数数值可以分别测定铝，铁含量，互不影响，铁，铝含量分别在１．０～１６μｇ／２５ｍｌ，０．３～１０μｇ／２５ｍｌ范围内呈良好线性，用于测定纯     

饮料食品中Ge－132和Ge~（4＋）含量测定研究

本文报告了在０．０１ｍｏｌ／ＬＣＴＡＢ体系中，以Ｆ－为掩蔽剂、苯芴酮显色、用分光光度法测定饮料食品中Ｇｅ－１３２含量，最低检测限０．０５４μｇ／ｍＬ；线性范围０．５４～２７．１４μｇ／ｍＬ；回收率９６．３％～１０１．５％，并确定了Ｇｅ－１３２摩尔吸收系数（ε）３．３９×１０４。用本法测定了康寿茶、矿泉水和博士奶中Ｇｅ－１３２含量，灵敏度高、重现性和准确度好。用盐酸化本体系，研究了二氧化锗（Ｇｅ~（４＋））的含量测定，其最低检测限０．０２１μｇ／ｍＬ；线性范围１．０～２１．０μｇ／ｍｌ；回收率９５．８％～１０２．８％，Ｇｅ－１３２不干扰。饮料食品中同时存在Ｇｅ－１３２和Ｇｅ（４＋）时，本体系可分别测定两者含量。     

Determination of lamivudine and zidovudine in binary mixtures using first derivative spectrophotometric, first derivative of the ratio-spectra and high-performance liquid chromatography-UV methods

Three methods are presented for the simultaneous determination of lamivudine and zidovudine. The first method depends on first derivative UV spectrophotometry, with zero-crossing and peak-to-base measurement. The first derivative amplitudes at 265.6 and 271.6 nm were selected for the assay of lamivudine and zidovudine, respectively. The second method depends on first derivative of the ratio-spectra by measurements of the amplitudes at 239.5 and 245.3 nm for lamivudine and 225.1 and 251.5 nm for zidovudine. Calibration graphs were established for 1-50 μg/ml for lamivudine and 2-100 μg/ml for zidovudine. In the third method (HPLC), a reversed-phase column with a mobile phase of methanol:water:acetonitrile (70:20:10 (v/v/v)) at 0.9 ml/min flow rate was used to separate both compounds with a detection of 265.0 nm. Linearity was obtained in the concentration range of 0.025-50 μg/ml for lamivudine and 0.15-50 μg/ml for zidovudine. All of the proposed methods have been extensively validated. These methods allow a number of cost and time saving benefits. The described methods can be readily utilized for analysis of pharmaceutical formulations. There was no significant difference between the performance of all of the proposed methods regarding the mean values and standard deviations. The described HPLC method showed to be appropriate for simultaneous determination of lamivudine and zidovudine in human serum samples.     

Spectrophotometric and spectrodensitometric determination of paracetamol and drotaverine HCl in combination

Thin-layer chromatography, first derivative, ratio spectra derivative spectrophotometry and Vierordt's method have been developed for the simultaneous determination of paracetamol and drotaverine HCl. TLC densitometric method depends on the difference in Rf values using ethyl acetate:methanol:ammonia (100:1:5 v/v/v) as a mobile phase. The spots of the two drugs were scanned at 249 and 308 nm over concentration ranges of 60-1200 microg/ml and 20-400 microg/ml with mean percentage recovery 100.11%+/-1.91 and 100.15%+/-1.87, respectively. The first derivative spectrophotometric method deals with the measurements at zero-crossing points 259 and 325 nm with mean percentage recovery 99.25%+/-1.08 and 99.45%+/-1.14, respectively. The ratio spectra first derivative technique was used at 246 and 305 nm with mean percentage recovery 99.75%+/-1.93 and 99.08%+/-1.22, respectively. Beer's law for first derivative and ratio spectra derivative methods was obeyed in the concentration range 0.8-12.8 and 0.4-6.4 microg/ml of paracetamol and drotaverine HCl, respectively. Vierordt's method was applied to over come the overlapping of paracetamol and drotaverine HCl in zero-order spectra in concentration range 2-26 and 2-40 microg/ml respectively. The suggested methods were successfully applied for the analysis of the two drugs in laboratory prepared mixtures and their pharmaceutical formulation. The validity of the methods was assessed by applying the standard addition technique. The obtained results were statistically agreed with those obtained by the reported method.     

Rapid and Accurate Determination of Acetaminophen and Phenprobamate in Binary Mixtures by Derivative-Differential UV Spectrophotometry and Ratio-Spectra Derivative Spectrophotometry

ABSTRACT

Derivative-Differential UV spectrophotometry and ratio-spectra first derivative spectrophotometry are presented for the simultaneous determination of analgesic and myorelaxan mixtures, namely acetaminophen (A)- phenprobamate (P). Derivative-Differential UV spectrophotometry is based on pH changes. The other method depends on the application ratio-spectra first derivative spectrophotometry to resolve the interference due to spectral overlapping.

The proposed methods were applied to the determination of this compound in synthetic mixtures and in pharmaceutical preparations. The proposed methods, which give thoroughly comparable data, are simple and rapid, and allow one to obtain precise and accurate results.     

Application of Derivative and Ratio Spectra Derivative Spectrophotometry for the Determination of Pseudoephedrine Hydrochloride and Acrivastine in Capsules

Abstract

Two new spectrophotometric methods are used for the determination of acrivastine and pseudoephedrine hydochloride in their mixture without previous chemical separation. In the first, second derivative spectrophotometry, the measurements are made at 288.0 nm for acrivastine and at 270.2 nm for pseudoephedrine hydrochloride in the second derivative spectra of their solution in 0.1M NaOH. In the second, ratio spectra derivative spectrophotometry, the amplitudes are measured at 276.0 nm and 298.5 nm corresponding to two maximums for acrivastine, and at 252.6 nm and 268.3 nm corresponding to a maximum and a minumum, respectively, for pseudoephedrine hydrochloride in first derivative of their ratio spectra plotted by using of their solutions as divisor. The methods were successfully applied for the determination of these drugs in a commercial pharmaceutical formulation capsule.     

Derivative and Derivative Ratio Spectrophotometric Analysis of Antihypertensive Ternary Mixture of Amiloride Hydrochloride,Hydrochlorothiazide and Timolol Maleate

Two simple, rapid and reliable spectrophotometric methods are described for the resolution of the three‐component mixture of amiloride hydrochloride (AMD), hydrochlorothiazide (HCT) and timolol maleate (TIM). The first method involves the use of derivative spectrophotometry with the zero‐crossing technique where AMD was easily determined using its ⁰D and ¹D(Δλ = 6) amplitudes at 365 and 385 nm, respectively, while HCT and TIM were determined by measuring the ³D(Δλ = 6) amplitude at 265 nm and the ¹D(Δλ = 8) amplitude at 315.4 nm, respectively. The second method involves the application of the ratio‐spectra zero‐crossing first and second derivative spectrophotometry where two points have been used for the quantification of each compound. For the determination of AMD, HCT was used as divisor and the ¹DD (Δλ = 4) and ²DD (Δλ = 6) values at 299.4 and 311 nm, respectively, were plotted against AMD concentration; while — by using TIM as divisor — the ²DD (Δλ = 6) amplitudes at 264.2 and 290 nm were found to be proportional to HCT concentration. TIM was assayed in the mixture using its ¹DD (Δλ = 6) amplitudes at 289.8 nm (Divisor was AMD) and 314.8 nm (Divisor was HCT). Synthetic mixtures of different proportions and laboratory‐made tablets were assayed by the proposed methods and the results revealed good accuracy and repeatability of the developed methods.     

Analysis of Metal Ions in Environmental Samples - III Synergistic Determination of Vanadium (V) As its Mixed Complex with N-0-Methoxyphenyl-2-Thenohydroxamic Acid and 3-(0-Carboxyphenyl)-1-Phenyltriazine-N-0Xide

Abstract

A highly sensitive, selective, and rapid method for the spectrophotometry determination of vanadium(V) at trace levels is described. The method is based on the selective extraction of vanadium(v) from strongly acidic (3–6 M hydrochloric acid) met ium with solution of N-0-methoxyphenyl-2- thenohydroxamic acid (0MTHA) in chloroform. The extract is then equilibrated with 3-(0-carboxyohenyl)-1-phenyltriazine-N-oxide(CPPTNO) at pH ? 1.5 and the resulting colour is measured at 445 nm. The colour system obeys Beer's law over the range 0–20 -μg/ml of vanadium; the molar absorptivityat the wavelength of maximum absorption (445 nm), and the Sandell sensitivity of the method are 1.1 × 10⁴1. mole^?1 cm^?1 and 0.005 μg/ml respectively.     

A comparative study on various spectrometries with thin layer chromatography for simultaneous analysis of drotaverine and nifuroxazide in capsules

Three spectrophotometric methods including Vierordt's method, derivative, ratio spectra derivative, and thin layer chromatography (TLC)-UV densitometric method were developed for simultaneous determination of drotaverine HCl (DRT) and nifuroxazide (NIF) in presence of its impurity, 4-hydroxybenzohydrazide (4-HBH). In Vierordt's method, (E(1 cm)(1%)) values were calculated at 227 and 368 nm in the zero-order spectra of DRT and NIF. By derivative spectrophotometry, the zero-crossing method, drotaverine HCl was determined using the second derivative at 245 nm and the third derivative at 238 nm, while nifuroxazide was determined using the first derivative at 399 nm and the second derivative at 411 nm. The ratio spectra derivative spectrophotometry is basedon the measure of the amplitude at 459 nm for DRT and at 416 nm for NIF in the first derivative of the ratio spectra. Calibration graphs of the three spectrophotometric methods were plotted in the range 1-10 mug/ml of DRT and 2-20 mug/ml of NIF. TLC-UV densitometric method was achieved on silica gel plates using ethyl acetate : methanol : ammonia 33% (10 : 1 : 0.1 v/v/v) as the mobile phase. The Rf values were 0.74, 0.50, 0.30+/-0.01 for DRT, NIF and 4-HBH, respectively. On the fluorescent plates, the spots were located by fluorescence quenching and the densitometrical area were measured at 308 and 287 nm with linear range 0.2-4 mug/spot and 0.6-12 mug/spot for DRT and NIF, respectively. The proposed methods have been successfully applied to the commercial pharmaceutical formulation without any interference of excipients. Mean recoveries, relative standard deviations and the results of the proposed methods were compared with those obtained by applying the alternate methods.     

Simultaneous Determination of Caffeine and Meclizine Dihydrochloride in Sugar-Coated Tablets

Abstract

In this study, simultaneous determination of caffeine and meclizine dihydrochloride in their binary mixture was conducted by two spectrophotometric methods. In the first method, derivative spectrophotometry, the quantification of caffeine and meclizine dihydrochloride was performed by reading the dA/dλ values at 286.2 nm and 243.4 nm respectively in the first derivative spectra of their mixture in methanol. The relative standard deviation of the method was 0.54% for caffeine and 0.67% for meclizine dihydrochloride. In the second, selective precipitation + derivative spectrophotometry, determination of meclizine dihydrochloride was carried out by precipitation with potassium ferricyanide at pH 2 selectively, then measuring the absorbance of its solution in methanol at 420.8 nm, and determination of caffeine was succeeded by reading the dA/dλ values at 260.6 nm in the first derivative spectra of the remaining solution after precipitation. Relative standard deviation of the method was found to be 0.56% for caffeine and 1.85% for meclizine dihydrochloride. These two methods were applied successfully to a sugar-coated tablet containing these drugs.     

Derivative spectrophotometric analysis of benzophenone (as an impurity) in phenytoin

ABSTRACT: Three simple and rapid spectrophotometric methods were developed for detection and trace determination of benzophenone (the main impurity) in phenytoin bulk powder and pharmaceutical formulations. The first method, zero-crossing first derivative spectrophotometry, depends on measuring the first derivative trough values at 257.6 nm for benzophenone. The second method, zero-crossing third derivative spectrophotometry, depends on measuring the third derivative peak values at 263.2 nm. The third method, ratio first derivative spectrophotometry, depends on measuring the peak amplitudes of the first derivative of the ratio spectra (the spectra of benzophenone divided by the spectrum of 5.0 μg/mL phenytoin solution) at 272 nm. The calibration graphs were linear over the range of 1-10 μg/mL. The detection limits of the first and the third derivative methods were found to be 0.04 μg/mL and 0.11 μg/mL and the quantitation limits were 0.13 μg/mL and 0.34 μg/mL, respectively, while for the ratio derivative method, the detection limit was 0.06 μg/mL and the quantitation limit was 0.18 μg/mL. The proposed methods were applied successfully to the assay of the studied drug in phenytoin bulk powder and certain pharmaceutical preparations. The results were statistically compared to those obtained using a polarographic method and were found to be in good agreement.     

Non-Extractive Simultaneous Spectrophotometric Determination of Trace Quantities of Palladium(II) and Tungsten(VI)

A second order derivative spectrophotometric method has been developed for the simultaneous determination of Palladium(II) and Tungsten(VI) using 3,4-dihydroxybenzaldehyde isonicotinoylhydrazone (3,4-DHBINH) as a new complexing agent. The Pd(II) reacts with 3,4-DHBINH in the pH range from 3 to 7 to form green colored solution. The absorbance calibration curves were constructed for palladium(II) at 362 nm (0.53～6.40 μg/ml) and tungsten(VI) at 374 nm (0.92～11.40 μg/ml). The metal ions interfere with each other in determination of zero order as well as the first order spectrophotometry. The optimum condition for maximum color development and other analytical parameters were evaluated. The method was applied successfully for the determination of palladium in hydrogenation catalyst and tungsten in industrial waste water samples.