CuCl2和HY分子筛的表面反应及Cu/Y分子筛的制备及其催化甲醇氧化羰基化

以CuCl₂为前驱物与HY分子筛进行固相离子交换制备了Cu/Y催化剂,采用热重方法研究了CuCl₂与HY分子筛的表面固相离子交换反应,结合活性测试表明催化剂中高度分散的CuCl和离子交换形式的Cu⁺物种是甲醇氧化羰基化合成碳酸二甲酯的催化活性中心。X射线光电子能谱表征和元素分析结果表明,活性金属Cu主要以CuCl形式存在于分子筛外表面,而在分子筛笼内则以交换的Cu⁺和少量吸附的CuCl形式存在。与以CuCl为交换铜源所制催化剂相比,以CuCl₂为铜源制备的催化剂Cu含量低,催化活性更高。     

CuY制备方法对其催化甲醇氧化羰基化活性中心的影响

以Cu(NO₃)₂为铜源,以NaY和HY分子筛为载体,通过溶液离子交换法和等体积浸渍法制备了不同的无氯CuY催化剂,并进行了气相甲醇氧化羰基化催化活性研究。通过浸渍法制备的催化剂Cu含量为10%,而以NaY和铜氨溶液离子交换制备的催化剂Cu含量只有6.3%,但其催化活性和选择性均较好。通过催化剂的Cu元素分析、低温氮吸附-脱附、XRD、H₂-TPR、XPS和TPD等表征表明,溶液离子交换法制备的催化剂,Cu物种以离子的形式高度分散于分子筛骨架结构中,较好地保持了分子筛晶体结构,并对甲醇有较强的吸附能力,催化活性较高,而将等体积浸渍Cu(NO₃)₂溶液后的HY或NaY分子筛,在400 ℃焙烧过程中,发生了固体离子交换反应,形成了连接于分子筛骨架的Cu²⁺,但以HY为载体更容易进行固体离子交换,未交换的铜物种以CuO的形式分散到分子筛表面。在600 ℃高温活化中,催化剂中Cu²⁺可部分还原为活性物质Cu⁺,但以NaY和铜氨溶液离子交换制备的催化剂Cu²⁺自还原能力最大。     

NO2对Cu/SAPO-34分子筛催化剂上NH3选择性催化还原NO性能的影响

主要考察了NO₂对Cu/SAPO-34 分子筛催化剂在整个温度范围内（100-500 ℃）NH₃选择性催化还原（SCR）NO性能的影响. 研究所使用样品为新鲜Cu/SAPO-34 催化剂在750 ℃下水热处理4 h 的稳定期样品.通过X射线衍射（XRD）和扫描电子显微镜（SEM）对样品的结构以及形貌进行表征,采用SCR活性评价、动力学实验以及原位漫反射傅里叶变换红外光谱（in situ-DRIFTS）表征催化剂的性能以及催化剂表面物种的变化. 活性评价实验结果表明,NO₂会抑制催化剂的低温（100-280 ℃）活性,但其存在会提高催化剂的高温（280 ℃以上）活性. 与此同时,随着反应物中NO/NO₂的摩尔比例减少,由于NH₄NO₃物种的分解,副产物（N₂2O）的浓度增大. 动力学结果表明,Cu/SAPO-34 催化剂上快速SCR反应的表观活化能（E_a=64.02 kJ·mol^-1）比标准SCR反应的表观活化能（E_a=48.00 kJ·mol^-1）更大. In situ-DRIFTS实验结果表明NO比NO₂更容易在催化剂表面形成硝酸盐,并且NO₂更容易与吸附在Brønsted 酸性位上的NH₃物种反应生成NH₄NO₃. 低温下,催化剂表面的NH₄NO₃物种会覆盖SCR反应的活性位,造成活性降低,但在高温时,形成的NH₄NO₃物种一部分会被NO还原为N2,而另一部分会直接热分解为N₂O,造成催化剂的选择性降低.     

Mo 和 Cu 助剂对 FeK/SiO2 催化剂费托合成性能的影响

 研究了 Mo 和 Cu 助剂对 FeK/SiO₂ 催化剂的性质及费托 (F-T) 合成性能的影响. 采用 N₂ 物理吸附、H₂ 程序升温还原、X 射线衍射、穆斯堡尔谱和 X 射线光电子能谱技术对催化剂进行了表征. 结果表明, Mo 加入后与 Fe 产生了较强的相互作用, 抑制了催化剂的还原和碳化; Cu 助剂的加入促进了催化剂的还原和碳化; 当 Mo 和 Cu 共同加入后, 催化剂的还原和碳化行为与单独加入 Cu 助剂时相似. 催化剂 F-T 合成性能在固定床上于 280 ^oC, 1.5 MPa, 2 000 h^-1, H₂/CO = 2.0 的合成气中测试. 结果表明, Mo 的加入降低了催化剂活性, 但提高了重质烃 (C₅₊) 的选择性; Cu 的添加提高了催化剂的活性, 但对稳定 C₅₊选择性作用不明显. Mo 和 Cu 共同加入后, 催化剂既表现出较为稳定的 C₅₊选择性, 同时其活性也没有降低.     

Cu的负载方法对CuSAPO-34脱除柴油车尾气中NOx的影响

采用X射线衍射、扫描电镜、原子吸收、程序升温还原、X射线吸收近边吸收谱、X射线光电子能谱、氮吸附等手段对水热合成(HS)、等体积浸渍(PVI)与离子交换(IE)法制备的CuSAPO-34样品进行了表征,并评价了老化前后催化剂上C₃H₆-SCR与NH₃-SCR脱除模拟柴油车尾气中NO_x的反应活性.结果表明,IE法制得的催化剂活性最高,尤其在C₃H₆-SCR低温阶段;PVI法制得的催化剂活性最差.制备方法影响CuSAPO-34催化剂的比表面积、孔径分布和活性组分价态从而改变其催化活性.各催化剂均存在Cu⁺和Cu²⁺,但比例明显不同.HS样品以Cu²⁺为主,另两种样品则含较多的Cu⁺.老化不仅部分破坏了分子筛的形貌、降低了分子筛的比表面积,尤其是表面Cu含量,而且有部分Cu生成了CuSO₄,使得老化后催化剂的脱硝活性降低.PVI法制得的催化剂老化后活性下降幅度最小,表明该分子筛抗老化能力较强.     

CuFe-SAPO-34分子筛的结构和催化性能研究

采用一步水热合成法,通过调变初始凝胶中的硅铁比,制备系列铜铁含量不同的CuFe-SAPO-34催化剂用于NH₃选择性催化还原NO_x反应（NH₃-SCR）,并采用ICP、XRD、SEM、BET、H₂-TPR等方法对其结构进行表征.结果表明,CuFe-SAPO-34催化剂具有典型的CHA结构,Cu和Fe均处于分子筛载体的离子交换位.当初始凝胶SiO₂/Fe₂O₃=10时,Cu_2.5Fe_3.1-SAPO-34催化剂具有最大的比表面积和孔容.掺杂适量的Fe,可提高活性物种Cu²⁺的比例及其氧化还原性能,显著降低Cu物种的聚集程度.NH₃-SCR反应结果表明,Cu_2.5Fe_3.1-SAPO-34催化剂具有最宽的反应温度窗口.与Cu-SAPO-34相比,Fe的掺杂显著提高了其高温段的催化活性和低温抗水能力,提高了Cu-CHA催化剂在实际应用中的稳定性.     

CO2在纳米SiO2/TiO2悬浮体系中的光催化还原

用水热法合成了氧化硅改性的具有高比表面积、高催化活性的锐钛型二氧化钛, 并在其悬浮体系中将CO₂光催化还原合成甲醇. 采用XRD, TEM, 物理吸附, UV-Vis吸收光谱和FTIR等表征手段对催化剂结构特征进行了研究. 结果表明: 添加氧化硅后, 氧化硅和二氧化钛之间形成Si—O—Ti键, 抑制了TiO₂晶粒生长, 提高了锐钛型TiO₂的比表面积, 且随着含硅量的增加, SiO₂/TiO₂的UV吸收逐步蓝移, 禁带宽度增加. 还原反应结果表明: SiO₂/TiO₂具有光催化还原活性, 且随着含硅量的增加先增加后减小, 当SiO₂质量分数为3.5%时, SiO₂/TiO₂复合催化剂反应活性最强, 5 h内甲醇产量可达到21.0 mg/L, 并有少量甲醛生成.     

硅烷化对NH3选择性催化还原NOx催化剂CuCe/BEA水热稳定性的促进作用

采用硅烷化改性NH₃选择性催化还原NO_x催化剂CuCe/BEA,以提高催化剂的水热稳定性。X射线衍射、扫描电子显微镜和²⁷Al核磁共振谱图等研究证实,硅烷化改性明显抑制BEA分子筛骨架中Si-O-Al键的水解,保持其结构完整,从而有效提高水热处理后CuCe/BEA的催化活性。氨气-程序升温脱附和原位漫反射傅里叶变换红外光谱研究结果表明,硅烷化改性的催化剂由于保持更完整的骨架结构能够形成更多的酸性位点。此外,氢气-程序升温还原和X射线光电子能谱测试表明,硅烷化改性有利于提高活性铜物种的分散性。因此,相比于CuCe/BEA催化剂,硅烷化改性的CuCeSi/BEA催化剂具有更多的酸性位点和高度分散的Cu物种,共同促进了催化剂的水热稳定性。     

KCl对Cu-K-La/γ-Al2O3催化剂上HCl氧化反应性能的影响

采用等体积浸渍法制备了Cu-K-La/γ-Al₂O₃催化剂,考察了KCl对该催化剂催化HCl氧化制Cl₂反应性能的影响. 当KCl的负载量为5 wt%时,Cu-K-La/γ-Al₂O₃催化剂表现出较好的催化活性和稳定性,可在较大的原料气空速变化范围内使用. 在0.1 MPa,360 ℃,空速450 L/（kg-cat·h）和HCl/O₂摩尔比为2：1的反应条件下,Cu-K-La/γ-Al₂O₃催化剂上HCl转化率在100 h内保持85%以上. 表征结果表明,Cu,K和La物种均高度分散于γ-Al₂O₃载体表面;一定量KCl的加入可降低Cu²⁺ → Cu⁺的还原温度,从而提高Cu²⁺活性中心的催化活性.     

碱性CeO2载体对Ru/CeO2催化剂氨合成活性的影响

钌基催化剂因其在低温低压下具有比常规的铁基催化剂更具活性的特点成为合成氨催化剂的理想选择.我们研究了CeO₂载体表面碱性对Ru基合成氨催化剂的影响.通过调节KOH沉淀剂的量来制备具有不同碱性位点的CeO₂载体（pH=10/11/12）,证明了催化剂适当碱性位点密度提高了合成氨催化活性.催化性能测试结果表明,1.25% Ru/CeO₂-11催化剂在3.8 MPa,450℃,H₂/N₂=3（60 mL·min^-1）下表现出优异的氨合成活性（7040 μmol·g^-1·h^-1）.CeO₂-11的碱性位点增强了载体的电子给予能力,这有利于电子向活性金属Ru转移,从而促进了N₂的活化.碱金属和碱土金属的引入提高了活性金属Ru的还原能力.4% Cs-1.25% Ru/CeO₂-11（12 000 μmol·g^-1·h^-1）催化剂具有更多的氧空位,这增加了Ru周围的电子密度并促进了N≡N的裂解.通过XRD,BET,SEM,CO₂-TPD,H₂-TPR和XPS分析了不同碱性CeO₂载体对合成氨催化反应的影响.     

Highly dispersed Cu supported on mesoporous Al-KIT-6 for oxidative carbonylation of methanol to dimethyl carbonate

Microporous NaY zeolite is a common support of Cu catalysts for oxidative carbonylation of methanol, but the dispersion of Cu species on NaY is usually subjected to its micropore size. Here, ordered mesoporous KIT-6 was employed as the support for Cu catalyst and Al was incorporated into its framework to increase the surface acidity, which eventually improves the surface exchange capacity and Cu dispersion. The evolution of the state of Cu species on KIT-6 was analyzed combined with control of Cu loading. The physicochemical properties of the supports and corresponding catalysts were characterized by N₂ adsorption–desorption, X-ray diffraction, ammonia temperature programmed desorption, Fourier transform infrared spectra, transmission electron microscopy, hydrogen temperature programmed reduction, and X-ray photoelectron spectroscopy. It was found that mesoporous KIT-6 showed better Cu dispersion than microporous NaY zeolite. Agglomerated CuO, dispersed CuO, and Cu²⁺ are the major Cu species observed on the catalyst surface. The increased surface acidic sites of KIT-6 by Al incorporation promoted the formation of Cu²⁺ and dispersion of CuO. With the increase in Cu loading, the Cu²⁺ content in the catalyst was decreased gradually along with increase in the bulk CuO. It was speculated that some exchanged Cu²⁺ could be transformed into highly dispersed CuO and even bulk CuO after calcination at a high Cu loading. Combined with the catalyst evaluation results, it was deduced that highly dispersed Cu²⁺ and CuO particles play significant roles in catalytic activity. The catalyst Cu/Al-K-10 achieved the highest space time yield of dimethyl carbonate of 135.4 mg/(g·h), which is 2.7 times the Cu/K-10 owing to its more dispersed Cu species. This laid the basis for preparing highly dispersed Cu species on mesoporous silica supports.     

Cu_xCo_(1-x)/Al_2O_3/FeCrAl整体式催化剂上甲苯催化燃烧(英文)

以FeCrAl合金薄片为基底,Al2O3浆料为过渡胶体,不同摩尔比的Cu、Co为催化活性组分,制备了一系列CuxCo1-x/Al2O3/FeCrAl(x=0-1)新型整体式催化剂.采用X射线粉末衍射(XRD),扫描电子显微镜(SEM),X光电子能谱(XPS)和程序升温还原(TPR)等手段对催化剂的结构进行了表征.在微型固定床反应器上评价了催化剂的催化甲苯燃烧性能.研究结果表明:在所制备的整体式催化剂上,当Cu含量比较低时,形成了Cu-Co-O固溶体;当Cu含量比较高时,可以测得CuO的衍射峰.催化剂表面颗粒大小和形貌与Cu、Co摩尔比密切相关.在催化剂表面,Co以Co2+和Co3+价态存在,而Cu主要以Cu2+价态存在.催化剂中的Cu可以改善Co的氧化还原性,从而有利于催化剂活性的提高.在所制备的催化剂中,Cu0.5Co0.5/Al2O3/FeCrAl催化剂具有最好的活性,甲苯在374oC可以完全催化燃烧消除.     

Cu-loaded dealuminated Y zeolites active in selective catalytic reduction of nitric oxide with ammonia

The selective catalytic reduction of NO with ammonia in the presence of oxygen has been carried out on Cu-loaded dealuminated Y zeolite catalysts. Copper was introduced by the usual ion-exchange procedure with an aqueous solution of cupric acetate. On deeply dealuminated USY zeolites, Cu²⁺ was supported in the amount larger than 2Cu/Al = 2, resulting in the formation of CuO fine particles in addition to the isolated and dimer Cu²⁺ species. The specific catalytic activity per surface copper on the CuO particles was very high compared with these Cu²⁺ species. NO adsorption measurement revealed the higher dispersion of CuO on the deeply dealuminated USY than on SiO₂, which made Cu/USY a better catalyst for the reduction of NO. The reaction intermediates were investigated through the IR spectra of adsorbed species.     

Cu-loaded dealuminated Y zeolites active in selective catalytic reduction of nitric oxide with ammonia

The selective catalytic reduction of NO with ammonia in the presence of oxygen has been carried out on Cu-loaded dealuminated Y zeolite catalysts. Copper was introduced by the usual ion-exchange procedure with an aqueous solution of cupric acetate. On deeply dealuminated USY zeolites, Cu²⁺ was supported in the amount larger than 2Cu/Al=2, resulting in the formation of CuO fine particles in addition to the isolated and dimer Cu²⁺ species. The specific catalytic activity per surface copper on the CuO particles was very high compared with these Cu²⁺ species. NO adsorption measurement revealed the higher dispersion of CuO on the deeply dealuminated USY than on SiO₂, which made Cu/USY a better catalyst for the reduction of NO. The reaction intermediates were investigated through the IR spectra of adsorbed species.     

Furfural Hydrogenation on Nickel‐promoted Cu‐containing Catalysts Prepared from Hydrotalcite‐Like Precursors

The nickel‐promoted Cu‐containing catalysts (Cu_xNi_y‐MgAlO) for furfural (FFR) hydrogenation were prepared from the hydrotalcite‐like precursors, and characterized by X‐ray powder diffraction, inductively‐coupled plasma atomic emission spectroscopy, N₂ adsorption‐desorption, UV‐Vis diffuse reflectance spectra and temperature‐programmed reduction with H₂ in the present work. The obtained catalysts were observed to exhibit a better catalytic property than the corresponding Cu‐MgAlO or Ni‐MgAlO samples in FFR hydrogenation, and the CuNi‐MgAlO catalyst with the actual Cu and Ni loadings of 12.5 wt% and 4.5 wt%, respectively, could give the highest FFR conversion (93.2%) and furfuryl alcohol selectivity (89.2%). At the same time, Cu⁰ species from the reduction of Cu²⁺ ions in spinel phases were deduced to be more active for FFR hydrogenation.     

Study of nano‐Cu/SiO2 catalysts for highly selective hydrogenation of acetophenone

Hydrogenation of acetophenone over nano‐Cu/SiO₂ catalysts was investigated. The catalysts, prepared by a liquid precipitation method using various precipitating agents, were characterized using low‐temperature nitrogen adsorption, X‐ray diffraction, temperature‐programmed desorption of ammonia, hydrogen temperature‐programmed reduction, transmission electron microscopy and X‐ray photoelectron spectroscopy. It was found that the catalysts prepared by a homogeneous precipitation method had better activity and stability than those prepared by a co‐precipitation method. The catalyst prepared using urea as precipitating agent had well‐dispersed copper species, high surface area and abundant pore structure. The catalytic performance and mechanism of the Cu/SiO₂ catalysts were further studied. It was found that the activity and stability of the catalysts could be improved by adjusting the proportion of Cu⁺/(Cu⁺ + Cu⁰). The sample prepared using urea as precipitating agent presented higher activity and selectivity. Also, the catalyst prepared using urea maintained a high catalytic performance while being continuously used for 150 h under the optimal reaction conditions.     

铁铜双金属催化剂选择性催化氧化氨为氮气

固定铜铁的总质量不变, 采用共浸渍法制备铜铁双金属催化剂. 为了更好地了解催化剂的性质, 分别用N₂吸附-脱附、H₂-程序升温还原(H₂-TPR)、NH₃-程序升温脱附(NH₃-TPD)、X射线衍射(XRD)和X射线光电子能谱(XPS)方法对制备的催化剂进行表征. 研究发现在100000 h^-1空速下, 铜铁双金属催化剂呈现出好的活性和氮气选择性. 在低温区, 随着铜含量的增加, 活性和氮气的选择性增加, 然而在高温区氮气的选择性直接和铁的含量相关. 其中催化剂Fe_0.25Cu_0.75/ZSM-5, 在350℃氨的转化率达到最高, 在300℃氮气的选择性上升到97%. Fe_0.75Cu_0.25/ZSM-5 在500 ℃有很高的氮气选择性甚至可以达到98%. 并且所有的催化剂均产生很少的N₂O副产物. 表征结果显示催化剂的酸量和铜物种的含量可以影响催化剂的活性, 并且高的还原能力和铁含量有助于高温氮气选择性的提高.     

Effect of copper precursors on the catalytic activity of Cu/ZSM-5 catalysts for selective catalytic reduction of NO by NH<Subscript>3</Subscript>

The Cu/ZSM-5 catalysts prepared by different copper precursors were used for the selective catalytic reduction (SCR) of NO _x with NH₃. The Cu/ZSM-5 catalyst prepared by the copper nitrate (Cu/ZSM-5-N) presented the best performance among the Cu/ZSM-5 catalysts and showed above 90 % NO _x conversion at 225–405 °C. The average particle size of CuO was 5.82, 9.20, and 11.01 nm over Cu/ZSM-5-N, Cu/ZSM-5-S (prepared by copper sulfate), and Cu/ZSM-5-C (prepared by copper chloride), respectively. The Cu/ZSM-5-N catalyst showed the highly dispersed copper species, the strong surface acidity, and the excellent redox ability compared with the Cu/ZSM-5-C and Cu/ZSM-5-S catalysts. The Cu⁺ and Cu²⁺ existed in the Cu/ZSM-5 catalysts and the abundant Cu⁺ over Cu/ZSM-5-N might be responsible for the superior SCR activity.     

Al2O3-TiO2 SOL-GEL MIXED OXIDES AS SUITABLE SUPPORTS FOR THE REDUCTION OF NO BY CO

Sol–Gel alumina-titania supports were prepared by the co-gelling aluminum tri-sec-butoxide and titanium isopropoxide (10 wt.% TiO₂) at pH 3 and pH 9. Supports showed specific surface areas higher than 250 m²/g, and Lewis acidity was observed by FTIR pyridine adsorption. Cu°, Cu¹⁺ and Cu²⁺species on impregnated Cu/Al₂O₃-TiO₂catalysts were identified by means of FTIR-CO adsorption. A correlation between Cu⁺/Cu²⁺ abundance and the activity for NO reduction by CO is reported.     

Pyrrolidone ligand improved Cu‐based catalysts with high performance for acetylene hydrochlorination

A series of Cu‐pyrrolidone/spherical activated carbon (SAC) catalysts were prepared via a simple incipient wetness impregnation method and then assessed in acetylene hydrochlorination, and the catalytic evaluation result indicated that the 1‐methyl‐2‐pyrrolidinone (NMP) ligand was found to be the most effective one to significantly improve the activity and stability of Cu catalyst. The catalyst with the optimal molar ratio of NMP/Cu = 0.25 showed 94.2% acetylene conversion at 180°C and an acetylene gas hourly space velocity of 180 h^?1. Moreover, the acetylene conversion of Cu‐0.25NMP/SAC remained stable over 99.1% for about 220 h under the industrial condition. Transmission electron microscopy (TEM) analyses proved that NMP ligand improved the dispersion of Cu species. In addition, hydrogen temperature‐programmed reduction (H₂‐TPR), X‐ray photoelectron spectra (XPS), thermogravimetric analysis (TGA), and Brunner–Emmet–Teller (BET) indicated that the additive of NMP was preferential to stabilize the catalytic active Cu⁺ and Cu²⁺ species and inhibit the reduction of Cu^α+ to Cu⁰ during the preparation process and reaction, hence restraining the coke deposition. Furthermore, the steady coordination structure between Cu and NMP was confirmed by Fourier‐transform infrared spectra (FT‐IR) and Raman combining with density functional theory (DFT) calculation, which could effectively lower the adsorption energy of catalyst for C₂H₂ and inhibit the serious carbon deposition caused by excessive acetylene self‐accumulation. Our findings suggest that the efficient, well‐stabilized cost‐effective, and environmentally friendly Cu catalyst has great potential in acetylene hydrochlorination.