Ni2+在γ-Al2O3上的分散状态及负载型Ni/γ-Al2O3催化剂的α-蒎烯加氢活性

用X-射线衍射(XRD)、紫外-可见漫散射光谱(UV-Vis DRS)、程序升温还原(TPR)、CO化学吸附和微反测试等方法研究了Ni²⁺在γ-Al₂O₃上的分散状态和负载型Ni/γ-Al₂O₃催化剂的α-蒎烯加氢催化活性。结果表明，当Ni²⁺负载量远低于其在γ-Al₂O₃载体表面分散容量时，Ni²⁺优先嵌入载体表面四面体空位，随着Ni²⁺负载量的增加，嵌入载体表面八面体空位Ni²⁺的比例增大。由于八面体Ni²⁺易被还原为金属态Ni⁰，NiO/γ-Al₂O₃样品的还原度随Ni²⁺负载量的增加而大幅度地增加，经氢还原所得Ni/γ-Al₂O₃催化剂的CO吸附量和α-蒎烯加氢催化活性大幅度增加。对La₂O₃助剂的作用进行了研究，结果表明分散在γ-Al₂O₃上的La³⁺物种可阻止Ni²⁺嵌入γ-Al₂O₃表面四面体空位，增大了八面体Ni²⁺物种所占比例，提高了催化剂的还原度，故Ni-La₂O₃/γ-Al₂O₃催化剂催化活性高于Ni/γ-Al₂O₃催化剂。     

预处理气氛对CuO/CeO2/γ-Al2O3催化剂表面性质及“NO+CO”反应性能的影响

用不同的预处理气氛制备了CeO₂/γ-Al₂O₃载体以调节表面Ce的价态,并以Cu(CH₃COO)₂为前驱体制备了CuCeAl催化剂。XRD和H₂-TPR的结果表明在还原气氛下处理的CeO₂/γ-Al₂O₃载体具有更多的活性氧原子,因此相应的CuCeAl催化剂表面有更多分散态的Cu²⁺/Cu⁺物种。NO+CO反应的结果表明分散态的Cu²⁺/Cu⁺是NO转化的活性物质,而Cu⁰在低温下具有较好的N₂选择性。因此,同时含有分散态Cu²⁺/Cu⁺和少量晶相Cu⁰的催化剂具有最好的催化性能。     

CO预处理对CuO/γ-Al2O3催化剂性能的影响

采用XRD，TPR，CO吸附in-situ IR，CO氧化反应等对CuO/γ-Al₂O₃催化剂经CO处理前后的结构、组成和催化性能进行了研究。结果表明，经CO在250 ℃下处理1 h后CuO/γ-Al₂O₃催化剂中出现了分散态Cu⁺物种，该物种的产生使催化剂的活性明显提高。     

Cu/SO42-/La2O3-ZrO2-Al2O3催化剂的制备及其对C3H6选择还原NO的催化性能

以Al₂O₃为基质，添加ZrO₂和La₂O₃，制成La₂O₃-ZrO₂-Al₂O₃复合载体，然后采用SO₄^2-进行改性，再负载上Cu²⁺，制备了铜基SO₄^2-改性的复合载体催化剂(Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃)。考察了它在富氧条件下对丙烯选择还原NO的催化性能，并借助XRD、SEM、TG、Py-IR、NH₃-TPD、FTIR和TPR等方法研究了Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃的结构和性能的关系。结果表明，ZrO₂的加入主要有利于提高催化剂的低温活性；La₂O₃的加入则主要有利于提高催化剂的热稳定性和还原性能；SO₄^2-能够与Zr形成螯合双配位结构，大幅度促使催化剂表面酸量增加并且酸性增强；因此，有效地提高了Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃在富氧条件下对丙烯选择还原NO的催化活性和水热稳定性。在无水条件下，Cu/SO₄^2-/La₂O₃-ZrO₂-Al₂O₃能使NO的最大转化率高达84.3%，即使在275 ℃ 10%水蒸气存在的情况下，仍能使NO的转化率高达81.2%。     

α-Fe2O3、γ-Al2O3、SiO2混合体系的表面配位反应

运用自动电位滴定技术分别研究了纳米α-Fe₂O₃、γ-Al₂O₃、SiO₂单一体系及三组分混合体系中氧化物表面的酸碱性质和对重金属离子Cu²⁺、Pb²⁺、Zn²⁺的吸附行为. 依据表面配位理论恒电容模式(CCM), 计算了相应的表面酸碱配位常数. 结果表明: α-Fe₂O₃/γ-Al₂O₃/SiO₂三组分混合体系的表面化学反应并非是单一体系的简单叠加, 而是存在着不同矿物表面间复杂的交互作用. 三组分表面酸碱反应平衡式和相应的酸碱反应平衡常数分别为: ≡XOH₂⁺?≡XOH+H⁺ (lgK_a1=-4.23), ≡XOH?≡XO^-+H⁺(lgK_a2=-8.41). 根据重金属离子Cu²⁺、Pb²⁺、Zn²⁺在α-Fe₂O₃/γ-Al₂O₃/SiO₂混合体系表面的吸附行为, 计算得到Cu²⁺、Pb²⁺、Zn²⁺在混合体系表面配位反应及其平衡常数如下: ≡XOH＋M²⁺?≡XOM⁺+H⁺; lgK=-2.20, -1.90, -3.20 (M=Cu, Pb, Zn).     

Al2O3催化剂结构对催化臭氧化活性的影响

以Al₂O₃为催化剂催化臭氧化处理邻苯二甲酸二甲酯. 通过XRD、比表面积、孔结构、FTIR和活性评价等方法对催化剂的物化性质及催化活性进行了研究, 考察了焙烧温度、成型粒径对催化剂活性的影响. 结果表明, Al₂O₃催化剂对臭氧化降解邻苯二甲酸二甲酯具有很高的催化活性, 反应120 min后, 总有机碳(TOC)的去除率从单独臭氧氧化的23.9%提高到55.1%; 焙烧温度对催化剂的活性具有很大的影响, 600 ℃催化剂催化活性最高; 随着焙烧温度的升高, Al₂O₃晶型经历了从γ-Al₂O₃到θ-Al₂O₃到α-Al₂O₃的转变, 催化剂的比表面积、焙烧得到的孔容逐渐变小, 晶体粒径变大, 表面•OH数量减少, 催化活性下降. Al₂O₃成型粒径的减小, 提高了催化剂的外比表面积, 减小了内部传质扩散的影响, 从而提高了催化活性.     

自组装型Pt/γ-Al2O3催化剂用于低温去除挥发性有机物

分别通过自组装法(AS)和浸渍法(WI)制备得到纳米催化剂Pt/γ-Al₂O₃-AS和Pt/γ-Al₂O₃-WI, 并用于评价甲苯、异丙醇、丙酮、乙酸乙酯等易挥发性有机物(VOCs)的氧化性能. 通过各种表征手段探究了催化剂形态、结构及表面性质与催化剂氧化活性的关系. 结果表明, Pt/γ-Al₂O₃-AS在低温下即可实现VOCs的完全氧化. 在气体浓度(体积分数)为1000×10^-6, 空速为18000 mL·g^-1·h^-1的条件下, 甲苯、异丙醇、丙酮、乙酸乙酯被Pt/γ-Al₂O₃-AS催化剂完全氧化的温度分别为130、135、145、215℃, 展现出了优异的氧化性能, 且具有很好的稳定性. 该催化剂较高的比表面积、较小的Pt纳米粒径、较好的Pt纳米颗粒分散度、更好的低温还原效果及丰富的表面羟基是具有较高催化活性的重要因素.     

溶剂化金属原子浸渍法制备Pd-Cu/γ-Al2O3低温CO氧化催化剂

Nano-particle Pd/γ-Al₂O₃ monometallic and Pd-Cu/γ-Al₂O₃ bimetallic catalysts were prepared by solvated metal atom impregnation (SMAI) method. The results of XRD measurement indicated that Pd- Cu alloy was formed in the bimetallic catalysts and the crystalline particle size of the alloy increased as Cu contents increased with av-erage diameters < 6.0nm for all the samples. XPS and Auger spectra showed that Pd was in zero- valent state, Cu existed mainly in zero- valent state and partially in monovalent state Cu⁺. The Pd/γ-Al₂O₃ and Pd-Cu/γ-Al₂O₃ catalysts exhibited higher activity for CO oxidation at low temperature. The activity of Pd-Cu/γ-Al₂O₃ bimetallic catalyst was higher than that of Pd/γ-Al₂O₃ monometallic catalyst. The Pd-Cu/γ-Al₂O₃ catalyst with Pd/Cu atomic ratio of 1∶1 showed the highest activity.     

γ-Al2O3表面原位合成Ni-Al-CO3LDHs研究

Ni-Al-CO₃LDHs/γ-Al₂O₃have been prepared using an in-situ synthesis technique. NH₃·H₂O was chosen as activation agent of Al on the γ-Al₂O₃surface as well as precipitant. Ni-Al-CO₃LDHs/γ-Al₂O₃was synthesized by controlling the reaction conditions such as temperature, concentration of Ni²⁺ and initial pH. The crystalline structure, chemical composition and porous structure were characterized by means of XRD, FT-IR, TG-DTA, ²⁷Al MAS-NMR and N₂ adsorption-desorption. The resulting sample of Ni-Al-CO₃LDHs/γ-Al₂O₃possesses higher specific area and narrower pore distribution, in which Ni-Al-CO₃LDHs are located on the surface of γ-Al₂O₃and share the same Al-O bonds with the γ-Al₂O₃lattice. Finally a possible structural model was proposed to account for the porous characters of Ni-Al-CO₃LDHs/γ-Al₂O₃.     

Effect of kcl on cucl2/γ-al2o3 catalyst for oxychlorination of ethane

Summary Effect of KCl on the structure and the catalytic properties of CuCl₂/γ-Al₂O₃ catalyst for ethane oxychlorination has been studied by means of solubility test, UV-vis spectroscopy, XRD, TPR, TEM and catalytic reaction. Addition of KCl decreases the interaction between active species CuCl₂ and γ-Al₂O₃ and increases the catalytic properties by accelerating the Cu(II) → Cu(I) reduction step.     

Surface Structure and Catalytic Performance of CuCl/SiO2-Al2O3 Catalysts for Methanol Oxidative Carbonylation

Aluminum was doped into amorphous silica gel to modify its surface structure. The obtained SiO₂-Al₂O₃ support was used to prepare the CuCl/SiO₂-Al₂O₃ catalyst by solid-state ion exchange, and the catalyst activity for liquid-phase oxidative carbonylation of methanol to dimethyl carbonate was investigated. The results showed that the prepared SiO₂-Al₂O₃ support kept the amorphous structure of the silica gel. The BET specific surface area of the silica gel was decreased to 200 m²/g, and the surface acid sites (including Brønsted acid sites) were increased. In the CuCl/SiO₂-Al₂O₃ catalyst, CuCl was not only dispersed on surface but also was ion exchanged with surface Brønsted acid sites of the SiO₂-Al₂O₃ support to form Cu⁺ species, which resulted in a decrease in BET specific surface area to 148 m²/g. These two kinds of Cu⁺ species on the catalyst surface were both active centers for the oxidative carbonylation of methanol to dimethyl carbonate. When the catalyst was prepared with Si/Al molar ratio of 5 and was calcined at 500 °C, the selectivity and space-time yield of dimethyl carbonate reached 74% and 1.27 g/(g·h), respectively.     

PdCl2-CuCl2/Al2O3催化剂低温催化CO氧化的失活机理

采用X射线衍射、N₂吸-脱附、X射线光电子能谱分析、氢气-程序升温还原和原位红外漫反射等方法对新鲜和失活的PdCl₂-CuCl₂/Al₂O₃低温催化CO氧化催化剂进行表征,研究了高相对湿度(100%)下催化剂的失活机理.结果表明,催化剂表面沉积的水使得活性铜物种容易从催化剂表面向载体孔道内部迁移,由于Pd、Cu相互作用弱化从而减弱了Pd与Cu物种间的相互作用,使得催化剂的氧化还原性能受到影响,抑制了Pd⁰再氧化为Pd²⁺的过程,从而因CO氧化反应中催化剂氧化还原循环受阻而导致失活.     

TiO2-Al2O3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO₂-Al₂O₃复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H₂原位还原法制备. 通过N₂吸附（BET）、X射线衍射（XRD）、透射电镜（TEM）、程序升温还原（TPR）,X射线光电子能谱（XPS）和等离子体发射光谱（ICP-AES）表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能. 结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al₂O₃的孔特征,具有较大的比表面积和较宽的孔分布,TiO₂主要以表面富集的形式分散在管状的γ-Al₂O₃表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni₂P和Ni₁₂P₅;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO₂趋于在块状的Al₂O₃表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni₂P. 不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n（Ti）/n（Al）=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340 ℃,3 MPa,氢油体积比500,液时空速3 h^-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

Study of CO2 Hydrogenation to Methanol over Cu-V/γ-Al2O3 Catalyst

The effect of vanadium addition to CU/γ-Al2O3 catalyst used in the hydrogenation of CO2 to produce methanol was studied. It was found that the catalytic performance of the Cu-based catalyst improved after V addition. The influence of reaction temperature, space velocity and the molar ratio of H2 to CO2 on the performance of 12%Cu-6%V/γ-Al2O3 catalyst were also studied. The results indicated that the best conditions for reaction were as follows: 240℃, 3600 h-1 and a molar ratio of H2 to CO2 of 3:1. The results of XRD and TPR characterization demonstrated that the addition of V enhanced the dispersion of the supported CuO species, which resulted in the enhanced catalytic performance of CU-V/γ-Al2O3 binary catalyst.     

α-Fe2O3/SiO2纳米颗粒混合体系表面的酸碱性质及其对重金属离子的吸附行为

以Fe(NO₃)₃·9H₂O和正硅酸乙酯(TEOS)为原料, 通过溶胶-凝胶法和辅助模板法分别制备了纳米α-Fe₂O₃和SiO₂, 并对所合成样品进行了粉末X射线衍射(XRD)和BET表征. 使用自动电位滴定仪测定了α-Fe₂O₃/SiO₂纳米颗粒混合体系的表面酸碱性质. 研究了在不同pH下α-Fe₂O₃/SiO₂混合体系对Cu²⁺、Pb²⁺、Zn²⁺离子的吸附行为. 基于上述实验数据, 用WinSGW软件计算了α-Fe₂O₃/SiO₂混合体系表面酸碱配位常数, 并得出结论: α-Fe₂O₃/SiO₂混合体系表面反应为单一脱质子反应≡XOH ⇔ ≡XO^-+ H⁺(lg K = -8.19±0.15), 明显区别于同时具有加质子和脱质子反应的α-Fe₂O₃/SiO₂/γ-Al₂O₃, α-Fe₂O₃/γ-Al₂O₃和SiO₂/γ-Al₂O₃等纳米颗粒混合体系. 在此基础上拟合得到α-Fe₂O₃/SiO₂混合体系吸附重金属离子Cu²⁺、Pb²⁺、Zn²⁺的表面络合反应平衡常数分别为:
≡XOH + M²⁺ ⇔ ≡XOM⁺+ H⁺ [lg K = -3.1, -3.6, -3.8 (M = Cu, Pb, Zn)].
≡XOH＋M²⁺＋H₂O ⇔≡XOMOH＋2H⁺[lg K = -8.8, -8.0, -10.5 (M = Cu, Pb, Zn)]     

Ternary [Al2O3–electrolyte–Cu] species: EPR spectroscopy and surface complexation modeling

Cu²⁺ binding on γ-Al₂O₃ is modulated by common electrolyte ions such as Mg²⁺, , and in a complex manner: (a) At high concentrations of electrolyte ions, Cu²⁺ uptake by γ-Al₂O₃ is inhibited. This is partially due to bulk ionic strength effects and, mostly, due to direct competition between Mg²⁺ and Cu²⁺ ions for the SO⁻ surface sites of γ-Al₂O₃. (b) At low concentrations of electrolyte ions, Cu²⁺ uptake by γ-Al₂O₃ can be enhanced. This is due to synergistic coadsorption of Cu²⁺ and electrolyte anions, and _. This results in the formation of ternary surface species (SOH₂SO₄Cu)⁺, (SOH₂PO₄Cu), and (SOH₂HPO₄Cu)⁺ which enhance Cu²⁺ uptake at pH < 6. The effect of phosphate ions may be particularly strong resulting in a 100% Cu uptake by the oxide surface. (c) EPR spectroscopy shows that at pH  pH_PZC, Cu²⁺ coordinates to one SO⁻ group. Phosphate anions form stronger, binary or ternary, surface species than sulfate anions. At pH  pH_PZC Cu²⁺ may coordinate to two SO⁻ groups. At pH  pH_PZC electrolyte ions and are bridging one O-atom from the γ-Al₂O₃ surface and one Cu²⁺ ion forming ternary [γ-Al₂O₃/elecrolyte/Cu²⁺] species.     

SO2对La0.8K0.2Cu0.05Mn0.95O3钙钛矿催化剂氧化碳烟的影响

采用柠檬酸配位法制备K、Cu掺杂的Lu0.8K0.2Cu0.05Mn0.95O3钙钛矿催化剂,运用程序升温氧化(TPO)考察在不同浓度SO2气氛下La0.8K0.2Cu0.05Mn0.95O3催化剂催化氧化模拟碳黑的性能,并用XRD、FFIR和XPS等进行表征.结果表明,催化剂在0～0.1%的SO2气氛中呈现出不同活性,φSO2≤0.05%的气氛可促进催化剂催化氧化碳黑的活性,当φSO2=0303%,催化剂活性最高;引入φSO2≥0.06%时催化剂活性明显下降.XPS说明表面活性氧的增加是低浓度的SO2促进催化活性的原因,同时XRD、FTIR结果表明高浓度的SO2所产生的大量SO42-是抑制催化剂活性的原因.     

Cu/La2O3-ZrO2-Al2O3催化剂的制备及其对NO选择性还原的催化性能

采用将Al(NO3)3、La(NO3)3和ZrOCl2的混合液滴入沉淀剂(NH4)2CO3中的共沉淀法制备La2O3-ZrO2-Al2O3复合载体,然后负载上Cu2+,制成Cu/La2O3-ZrO2-Al2O3催化剂。考察了该催化剂在富氧条件下对C3H6选择还原NO的催化性能,并借助扫描电子显微镜（SEM）、X射线衍射（XRD）、比表面积测定（BET）、吡啶吸附红外光谱（Py-IR）、程序升温还原（TPR）和热重分析（TG）等方法研究催化剂制备方法与结构、性能的关系。实验结果表明,采用将Al(NO3)3滴入(NH4)2CO3制得的γ-Al2O3能有效地增大催化剂的比表面积,加入La2O3能提高催化剂的热稳定性,加入ZrO2能大幅度增加催化剂表面L酸和B酸的酸量。因此,采用共沉淀法制备的La2O3-ZrO2-Al2O3复合载体能够使Cu/La2O3-ZrO2-Al2O3催化剂具有良好的催化性能,最佳催化活性温度为300℃,NO最大转化率高达88.9%,在有10%水蒸气存在的情况下,仍可达81.9%。