氨基功能化SBA-15的直接合成及其对CO_2的吸附性能研究

通过直接法合成了氨基功能化SBA-15介孔材料。使用X-射线粉末衍射法(XRD),N2吸-脱附,透射电子显微(TEM)等技术对氨基功能化材料进行了表征。实验结果表明:当反应原料中nAPTES/(nAPTES+nTEOS)≤0.20时,APTES功能化的材料都具有典型的介孔SBA-15结构;但当nAPTES/(nAPTES+nTEOS)≥0.225时,由于氨基对SBA-15结构的副作用导致SBA-15介孔结构坍塌。在氟离子辅助合成下可以获得高含量氨基(反应原料中nAPTES/(nAPTES+nTEOS)的比值为0.25)功能化的SBA-15材料,且此材料中的介孔孔径和BET比表面积都较大。CO2吸附结果表明,随着反应原料中APTES含量提高,所合成的材料对CO2的吸附量相应增加,同时在101kPa和25℃下,通过氟离子辅助合成的材料对CO2的吸附量远远优于无氟离子辅助合成材料的。本研究还对后嫁接法和直接合成法获得氨基功能化SBA-15介孔材料的优缺点进行了讨论。     

TEPA功能化SBA-15的CO_2吸附性能

以正硅酸乙酯(TEOS)为硅源,P123为模板剂,通过加入适量HAc及调整反应体系pH方式,采用水热及萃取法合成表面羟基含量较高的介孔SBA-15材料.以不同含量四乙烯五胺(TEPA)对SBA-15进行功能化,获得氨基功能化介孔SBA-15材料.利用X射线衍射(XRD)、N2吸-脱附、傅里叶红外光谱(FT-IR)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、元素分析等手段对材料结构性能进行表征.以不同含量TEPA功能化介孔SBA-15为吸附剂,对CO_2进行吸附,考察了吸附温度、CO_2浓度、水等对吸附效率的影响.实验结果表明,常温、常压下30%TEPA功能化介孔SBA-15的CO_2吸附量最高,且重复使用性能良好.     

氨基功能化介孔吸附剂的一步合成及其重金属吸附性能

以聚甲基含氧硅氧烷(PMHS)、正硅酸乙酯(TEOS)和氨丙基三甲氧基硅烷(APTMS)作为反应前驱体,在无需传统结构导向剂的溶胶-凝胶体系中制备了介孔结构发达的氮基功能化凝胶吸附剂,并采用元素分析、固体核磁共振、傅里叶红外光谱、低温氮气吸附/脱附、透射电镜和热重分析等手段对产物结构性能进行了表征.氮气吸附和透射电镜测...     

HCl对有序介孔氧化硅结构与形貌的影响

以三嵌段共聚物P123为有机模板导向剂、正硅酸乙酯TEOS为无机硅源, 在HCl存在的强酸性环境下, 采用水热法合成了有序介孔分子筛SBA-15. 采用XRD、SEM、TEM、N2吸附-脱附等手段对产物的结构与形貌进行了分析, 考察了HCl用量对有序介孔材料结构及形貌的影响. 结果表明, 在合成有序介孔氧化硅时, HCl发挥了催化和中间离子的双重作用, 促使棒状胶束形成六方有序排列, 降低SBA-15中微孔的数量, 而且对合成有序介孔氧化硅SBA-15的形貌有显著影响. 适宜的HCl用量对形成“珍珠链状”形貌的、热稳定性优良的SBA-15介孔材料具有重要作用.     

表面高巯基功能化介孔材料的制备及对Hg~(2+)的吸附性能

在酸性条件下,以三嵌段非离子表面活性剂P123为模板剂,四氧基硅烷(TEOS)预水解后与3-巯基丙基三乙基硅(MPTES)共聚,合成了具有不同巯基官能团比例x[n(MPTES)/n(TEOS+MPTES)]的功能化介孔材料(SBA-SH-x),其结构和性能经FT-IR,元素分析,SEM,TEM,小角X-ray和N2吸附-脱附表征。结果表明:x10%,SBA-SH-x为六方p6mm介观结构;10%x15%,SBA-SH-x为立方Ia3d介孔结构;x20%,SBA-SH-x为无序结构。SBA-SH-x在水溶液中吸附Hg2+的研究结果表明:SBA-SH-10和SBA-SH-15对Hg~(2+)吸附性能较好。     

可用于色谱固定相的介孔氧化硅球材料的合成

采用非离子型嵌段高分子表面活性剂EO₂₀PO₃₀EO₂₀ (P65)为结构导向剂, 正硅酸乙酯为硅源, 在酸性介质中, 静置法制备了微米级介孔氧化硅球. 通过改变合成温度、反应时间或者无机盐KCl的加入量, 可以调节介孔氧化硅球的直径(9.0～17.6 μm); 加入1,3,5-三甲苯(TMB)或者调节水热温度, 可以调节介孔氧化硅球的孔径(2.3～4.8 nm). 采用X射线衍射(XRD)、N₂吸附-脱附、扫描电镜(SEM)、激光散射粒度分布和对溶菌酶的吸附等方法, 对介孔氧化硅球的结构、孔性质、形貌、吸附性质等进行了表征. 实验发现, 孔径较小的介孔氧化硅球(≤4.3 nm)对溶菌酶的吸附不明显(≤42 mg/g), 而孔径(4.8 nm)大于溶菌酶直径的材料对溶菌酶有较大的吸附量(192 mg/g), 说明孔径均匀可调的介孔氧化硅球材料可以很好地用作体积排阻色谱柱的固定相.     

有机功能化介孔氧化硅的制备和表征

有机功能化的介孔氧化硅在催化领域、吸附分离、生物化学和电子学等领域有广泛的应用前景。本文综述了近年来有机功能化介孔氧化硅的研究进展,主要介绍了有机功能化的介孔氧化硅的制备方法、种类和表征手段,并对其未来发展前景进行了展望。有机功能化的介孔氧化硅的制备方法主要有接枝法、共缩聚法、有序介孔有机硅法和自模板法,常用的表征方法有粉末X-射线衍射分析、低温N₂吸附-脱附、透射电镜、红外光谱、热重分析、元素分析和²⁹Si、¹³C交叉极化和魔角旋转核磁共振等。     

介孔NH_2-Ce-Pr-O合成及其可见光催化性能EI北大核心CSCD

以P123(聚环氧乙烷-聚环氧丙烷-聚环氧乙烷三嵌段共聚物)为模板剂,Ce(NO_3)_3,Pr(NO_3)_3为原料,采用水热反应制备前驱物,经萃取除去P123后既得表面羟基含量较高的Ce-Pr-O介孔材料。利用氨基硅烷与表面羟基间的缩合作用,合成了氨基功能化介孔Ce-Pr-O。利用XRD,N_2吸脱附,Raman,FT-IR,XPS等技术对合成样品结构性能进行了表征。结果表明:以25%Pr(NO_3)_3掺杂所获得的Ce-Pr-O结构性能较好;该样品氨基功能化后,除孔径、表面积及孔容变小外,其他性能基本保持不变。以酸性红14(AR14)为探针分子,对合成材料的光催化性能进行评价。结果表明:由于Pr掺杂后形成氧缺位,提高了样品的可见光吸收强度;此外,通过嫁接氨基,提高AR14的吸附量。因此,所合成的氨基功能化介孔Ce-Pr-O在可见光作用下,能较彻底地催化降解溶液中的AR14。     

以十六烷基三甲基溴化铵为模板剂合成MCM-41/ZSM-5复合分子筛的研究

采用阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)为模板剂、以ZSM-5为晶种,在水热晶化条件下合成了同时具有微孔和介孔的MCM-41/ZSM-5复合分子筛;并考察了陈化温度、陈化时间、晶化时间及模板剂用量等条件对合成复合分子筛的影响.通过X射线衍射、扫描电镜、高分辨率透射电镜、红外光谱及N2静态吸附法等手段对合成样...     

介孔NH_2-Ce-Pr-O合成及其可见光催化性能

以P123(聚环氧乙烷-聚环氧丙烷-聚环氧乙烷三嵌段共聚物)为模板剂,Ce(NO_3)_3,Pr(NO_3)_3为原料,采用水热反应制备前驱物,经萃取除去P123后既得表面羟基含量较高的Ce-Pr-O介孔材料。利用氨基硅烷与表面羟基间的缩合作用,合成了氨基功能化介孔Ce-Pr-O。利用XRD,N_2吸脱附,Raman,FT-IR,XPS等技术对合成样品结构性能进行了表征。结果表明:以25%Pr(NO_3)_3掺杂所获得的Ce-Pr-O结构性能较好;该样品氨基功能化后,除孔径、表面积及孔容变小外,其他性能基本保持不变。以酸性红14(AR14)为探针分子,对合成材料的光催化性能进行评价。结果表明:由于Pr掺杂后形成氧缺位,提高了样品的可见光吸收强度;此外,通过嫁接氨基,提高AR14的吸附量。因此,所合成的氨基功能化介孔Ce-Pr-O在可见光作用下,能较彻底地催化降解溶液中的AR14。     

介孔SiO2的改性及对诺维信漆酶的交联固定化

采用十六烷基三甲基溴化铵(CTAB)为模板剂,四乙氧基硅烷(正硅酸乙酯,TEOS)为硅源,硝酸为催化剂来制备介孔SiO2,并采用后嫁接法对介孔SiO2进行氨基化改性。利用红外光谱(IR),X射线粉末衍射(XRD),差热-热重分析(DTA-TG),扫描电镜(SEM),元素分析,微电泳法及N2吸附-脱附方法对改性前后的产物进行表征。结果表明氨基已成功嫁接到介孔SiO2孔道中,改性后的介孔SiO2有序度有所下降,但仍为介孔材料;改性之后介孔材料的孔径、比表面积、孔体积均变小。等电点由原来的2.74变为4.75。本文还以氨基修饰的介孔SiO2为载体,通过交联剂戊二醛固定诺维信(Novozymes)工业级漆酶,并采用正交设计法对固定化条件进行了优化。研究表明漆酶经固定化后,其操作稳定性比游离酶高。     

基于长链离子液体模板合成Fe(Co、Ni)-MCM-48

以两亲长链离子液体(氯化-1-十六烷基-3-甲基咪唑)为模板剂,采用水热合成方法,分别合成了含铁、钴和镍的立方介孔分子筛MCM-48。通过XRD、TEM、ICP-AES、FTIR、UV-Vis和N₂吸附/脱附实验对其结构和形态进行了表征,并考察了钴掺杂量和模板剂用量对合成立方相结构的影响。结果表明,用该方法合成的试样具有较高的比表面积和规则的立方介孔孔道结构等特征;相对于铁和镍的掺杂试样,钴物种能以四面体的结构稳定地存在于立方介孔分子筛骨架中。     

Robust Amino-Functionalized Mesoporous Silica Hollow Spheres Templated by CO2 Bubbles

Hollow-structured mesoporous silica has wide applications in catalysis and drug delivery due to its high surface area, large hollow space, and short diffusion mesochannels. However, the synthesis of hollow structures usually requires sacrificial templates, leading to increased production costs and environmental problems. Here, for the first time, amino-functionalized mesoporous silica hollow spheres were synthesized by using CO₂ gaseous bubbles as templates. The assembly of anionic surfactants, co-structure directing agents, and inorganic silica precursors around CO₂ bubbles formed the mesoporous silica shells. The hollow silica spheres, 200–400 nm in size with 20–30 nm spherical shell thickness, had abundant amine groups on the surface of the mesopores, indicating excellent applications for CO₂ capture, Knoevenagel condensation reaction, and the controlled release of Drugs.     

含过渡金属HMS的合成和催化性能

利用中性伯胺（十二胺）作模板剂,合成了过渡金属Ｃｕ、Ｔｉ、Ｃｏ、Ｆｅ取代的ＨＭＳ中孔材料,ＸＲＤ和ＦＴ＝ＩＲ表征表明,Ｃｕ、Ｔｉ能有效地嵌入ＨＭＳ骨架壁中而不会造成其中孔有序度的下降;而Ｃｏ、Ｆｅ的嵌入会明显降低表面活性剂的模板组装作用,从而造成中孔结晶有序度的显著下降,催化实验结果表明：Ｃｕ－ＨＭＳ、Ｆｅ－Ｓｉｌｉｃａ是苯要不要羟基化的有效催化剂,而Ｔｉ－ＨＭＳ则是苯乙烯环氧化的有效催化剂。     

Synthesis, amino-functionalization of mesoporous silica and its adsorption of Cr(VI)

Mesoporous silica materials with a centered rectangular symmetry (cmm) have been synthesized through a facile direct-templating method using tetraethylorthosilicate (TEOS) and amphiphilic block co-polymers Pluronic P123 under acidic conditions. The amino groups have been grafted to as-synthesized mesoporous silica by [1-(2-amino-ethyl)-3-aminopropyl]trimethoxysilane (AAPTS). Thus obtained amino-functionalized mesoporous silica (denoted as NN-silica) was used for sequestration of Cr(VI) from aqueous solution. After sequestration of Cr(VI), the sample was denoted as Cr(VI)-silica. The parent mesoporous silica, NN-silica and Cr(VI)-silica were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and N(2) adsorption-desorption isotherms. XRD and TEM results confirm that the structure of these samples is centered rectangular symmetry (cmm). N(2) adsorption-desorption isotherms show that there is a remarkable decrease in surface area and pore volume for NN-silica (S(BET)=54.5 m(2)g(-1), V(P)=0.09 cm(3)g(-1)) and Cr(VI)-silica (S(BET)=53.2 m(2)g(-1), V(P)=0.07 cm(3)g(-1)) compared to the parent mesoporous silica (S(BET)=444.0 m(2)g(-1), V(P)=0.71 cm(3)g(-1)). The BJH desorption average diameter of NN-silica, Cr(VI)-silica and the parent mesoporous silica is 4.40 nm, 4.07 nm and 5.11 nm, respectively. The results reveal the channels of as-synthesized mesoporous silica are essentially grafted with abundant amino groups and loaded with Cr(VI). The adsorption experiment results show that the functionalized mesoporous silica materials possess an increased Cr(VI) adsorption capacity and the maximum Cr(VI) loadings at 25, 35 and 45 degrees C can reach 2.28, 2.86 and 3.32 mmol/g, respectively.     

聚乙烯亚胺修饰的氧化硅纳米管基吸附剂的制备及其CO_2吸附应用

以P123为模板,1,2-二(三甲氧基硅基)乙烷(BTME)为硅源合成了介孔氧化硅纳米管(E-SNTs).将ESNTs经过聚乙烯亚胺(PEI)修饰后制得吸附剂用于捕捉CO2.对吸附剂进行了透射电镜(TEM)、物理吸附、傅里叶变换红外(FTIR)光谱、热重分析(TGA)等表征.E-SNTs-PEI吸附剂的最佳CO2吸附温度为75°C.吸附剂的CO2吸附量随着PEI负载量的增加呈现先增大后减小的趋势,其中50%为最佳负载量,此时吸附剂的吸附量最大为3.32 mmol·g-1.相比较SBA-15基吸附剂,E-SNTs基吸附剂具有更优异的吸附性能.在有水汽的存在下,吸附剂E-SNTs-50的CO2吸附量达到3.75 mmol·g-1.经过四次循环吸脱附实验测试E-SNTs-PEI吸附剂的稳定性能,结果表明其CO2吸附量基本不变,该吸附剂表现出较好的稳定性和可再生能力.     

Photochromic ordered mesoporous hybrid materials based on covalently grafted polyoxometalates

Novel polyoxometalate (POM)-grafting mesoporous hybrid silicas, XW(11)/MHS (X=P, Si) and TBAPW(11)Si(2)/MHS, have been prepared respectively by co-condensation and post-synthesis routes based on the employment of Keggin-type monovacant XW(11) or a Si-substituted compound TBAPW(11)Si(2) as POM precursors. Upon characterization of the samples by FT-IR, XRD, ICP-AES, TEM and N(2) adsorption-desorption measurement, it was found that Keggin units were retained perfectly in ordered hexagonal mesopore channels with SBA-15 architecture and immobilized by covalent linkages on the mesopore wall. These materials, especially the co-condensed samples, exhibited stable and reversible photochromic properties under UV irradiation although no special organic component was supplied additionally as an electron donor. An investigation of the photochromism revealed that the photochromic response depended on the centre atom of the POM species (i.e., the redox potential of the POM), the content of the POM and the synthetic route of the sample, while the bleaching process was correlated not only to the redox potential but also to the pore size of the sample. The photochromic mechanism was also studied in detail by cyclic voltammetry, ESR, FT-IR and XPS techniques. It was found that the remaining P123 template acted as a reducing agent and was oxidized during the photochromic process accompanied by the reduction of the POM to heteropolyblue. Thus, a close contact between the POM and the remaining P123 chain in the sample is necessary. Low close-contact degree results in poor photochromic behavior of the post-synthesized sample and impregnated samples.     

Utilization of Environmentally Benign Dicyandiamide as a Precursor for the Synthesis of Ordered Mesoporous Carbon Nitride and its Application in Base‐Catalyzed Reactions

Assisted by a new dissolution procedure, dicyandiamide (DCDA), an environmentally benign and cheap precursor, has been employed for the synthesis of mesoporous carbon nitride (CN) materials through a nanocasting approach. The synthesized mesoporous materials possessed high specific surface areas (269–715 m² g^?1) with narrow pore‐size distributions (about 5 nm) and faithfully replicated the mesostructures of the SBA‐15 and FDU‐12 templates. Several characterization techniques, including XRD, SAXS, TEM, Raman and FTIR spectroscopy, XPS, and CO₂‐TPD, were used to analyze the physicochemical properties of these materials and the results showed that the mesoporous CND materials had graphitic‐like structures and consisted of CN heterocycles, as well as amino groups. In a series of Knoevenagel condensation reactions, as exemplified by the reaction of various aldehydes and nitriles, these mesoporous CND materials demonstrated high and stable catalytic activities, owing to an abundance of basic sites.     

源自密胺基多孔聚合物的富氮微孔炭及选择性吸附CO_2

以间苯二甲醛和三聚氰胺为原料,通过Schiff碱缩合反应合成了密胺基多孔聚合物(POP),经高温炭化后得到富氮微孔炭(NMC).利用N2吸脱附和傅里叶变换红外(FTIR)光谱表征了POP和炭化后产物NMC的结构和组成,与POP相比,NMC的官能团数量减少,比表面积和微孔孔容大幅增加.元素分析表明NMC含氮量高达12.5%(w).采用体积法测定了CO2、CH4和N2在NMC上的单组分吸附平衡等温线,NMC展示出良好的CO2吸附性能,298 K、100 kPa下CO2平衡吸附量可达2.34 mmol·g-1.双位Langmuir(DSL)模型和单位Langmuir(SSL)模型分别较好地描述了CO2、CH4和N2在NMC上的吸附平衡数据,在此基础上,应用理想吸附溶液理论(IAST)预测了双组分混合气在NMC上的吸附等温线,结果表明NMC对CO2-N2和CO2-CH4有非常高的CO2吸附选择性,分别为144.9和12.8.