4,4′-二乙炔二苯甲烷与苯乙炔的共聚及共聚物的表征研究

本文做了4,4′-二乙炔二苯甲烷的本体热均聚和催化均聚,并用(Ph_3P)_2PdCl_2为催化剂做了4,4′-二乙炔二苯甲烷与苯乙炔的共聚,对均聚和共聚物中的不溶不熔组分测定了密度、溶胀度、Huggins参数以及交联点间的平均分子量(?)_c。实验表明,该交联聚合物的最良溶剂是四氢呋喃,溶度参数为9.9ca1~0.5。cm~(-1.5),当用四氢呋喃为溶剂时的Huggins参数为0.34,并且在单体摩尔比中4,4′-二乙炔二苯甲烷用量越多,溶胀度越小,交联度越大。红外光谱分析表明,所有均聚及共聚物都为反式结构。     

1,4-丁炔二醇与4,4′-二乙炔联苯共聚物的合成及表征研究

 本文用(Ph₃P)₂PdCl₂为催化剂,合成了1,4-丁炔二醇(BD)与4,4-二乙炔联苯(DEBP)共聚物。对用不同比例的两种单体得到的共聚物测定了比重(d₄²⁵、溶胀度(θ_D)、最良溶剂及相邻两交联点之间的平均分子量(M_c)。实验表明,在两种单体摩尔比中,DEBP用量越多,共聚物中泡状微孔越多,颜色越淡,溶胀度和比重越小,交联度越大;DEBP/BD(摩尔比)大于1/5时,共聚物的最良溶剂为苯,溶度参数为9.15卡^0.5·cm^-1.5,是1/10时,其最良溶剂为乙醇,溶度参数是12.7卡^0.5·cm^-1.5。对共聚物还做了红外光谱表征。     

1,4-丁炔二醇与4,4′-二乙炔联苯共聚物的合成及表征研究

本文用(Ph_3P)_2PdCl_2为催化剂,合成了1,4-丁炔二醇(BD)与4,4-二乙炔联苯(DEBP)共聚物。对用不同比例的两种单体得到的共聚物测定了比重(d_4~(25)、溶胀度(θ_D)、最良溶剂及相邻两交联点之间的平均分子量(M_c)。实验表明,在两种单体摩尔比中,DEBP用量越多,共聚物中泡状微孔越多,颜色越淡,溶胀度和比重越小,交联度越大;DEBP/BD(摩尔比)大于1/5时,共聚物的最良溶剂为苯,溶度参数为9.15卡~(0.5)·cm~(-1.5),是1/10时,其最良溶剂为乙醇,溶度参数是12.7卡~0.5·cm~(-1.5)。对共聚物还做了红外光谱表征。     

耐高温交联侧基苯乙炔封端酰亚胺预聚体

合成了含有苯乙炔基的二胺单体 3,5-二氨基-4'-苯乙炔苯甲酮(DPEB), 并与3,3',4,4'-联苯四酸二酐(s-BPDA)和1,4-双(4'-氨基苯氧基)-2-(苯基)苯(p-TPEQ)进行了缩聚反应, 以4-苯乙炔苯酐作为封端剂, 合成了交联侧基苯乙炔封端酰亚胺预聚体(n=4). DSC测试结果表明, 引入交联侧基后预聚体依然保持着较宽的加工窗口. 利用所合成的预聚体在370℃热压1 h制备了热固性薄膜. DMA测试结果表明, 引入交联侧基的预聚体树脂具有更高的玻璃化转变温度, 并且其储存模量在玻璃化转变后有很好的保持.     

纳米Cu2O催化二苯甲烷二氨基甲酸苯酯无溶剂热分解制备二苯甲烷二异氰酸酯

研究了无溶剂条件下纳米Cu₂O催化二苯甲烷二氨基甲酸苯酯(MDPC)热分解制备二苯甲烷二异氰酸酯(MDI),考察了纳米Cu₂O的制备条件与反应条件对MDPC热分解反应性能的影响.结果表明,水解法制备的纳米Cu₂O在Ar中于300℃焙烧2h,其催化性能最佳;最佳的反应条件为Cu₂O用量为原料总重的0.06%,反应温度220℃,反应压力0.6kPa,反应时间12min,此时MDPC转化率达到99.8%,MDI选择性86.2%.     

4-苯乙炔苯酐封端聚酰亚胺树脂的合成与性能研究

使用3,3′,4,4′-二苯醚四酸二酐(ODPA)、3,3′,4,4′-联苯四酸二酐(BPDA)、1,3-双(4-氨基苯氧基)苯(1,3,4-APB)、3,4′-二氨基二苯醚(3,4′-ODA)和反应性封端剂4-苯乙炔苯酐(4-PEPA)合成了设计分子量为5000的系列苯乙炔基封端的聚酰亚胺低聚物,并使用XRD、DSC、TGA、FT-IR、DMA和流变仪等对低聚物的化学结构、热性能和熔体性能,固化后树脂的热性能和力学性能进行了测试.研究结果表明基于ODPA的低聚物具有低的熔体粘度和良好的熔体粘度稳定性,固化后的树脂具有很高的热失重温度,较高的玻璃化转变温度以及良好的力学性能尤其是高的断裂伸长率(>10%);基于BPDA的低聚物具有一定的结晶性,其结晶熔融温度与苯乙炔基固化交联温度相近,影响了材料的成型工艺性能.     

稀土络合催化苯乙炔直接成膜聚合 Ⅴ.苯乙炔在钕、铁混合络合催化体系中的直接成膜聚合

 乙酰丙酮(AA)、苯酰丙酮(BA)为配体的钕(Nd)、铁(Fe)混合催化剂与三异丁基铝[Al(i-Bu)₃]组成络合催化体系,能使苯乙炔在甲苯/己烷混合溶剂中直接聚合成膜。研究了其聚合反应规律及动力学行为,并对聚苯乙炔膜进行了全面表征,揭示了钕、铁两组分催化剂具有协同催化效应。     

苯乙炔封端的BTDA系列酰亚胺预聚体的研究

合成了具有苯侧基的二胺单体1,4-双(4'-氨基苯氧基)-2-(苯基)苯(p-TPEQ), 并与3,3',4,4'-苯酮四羧酸二酐(BTDA)进行缩聚反应, 分别以4-苯乙炔苯酐(PEPA)和4-苯乙炔-1,8-萘二甲酸酐(PENA)作为封端剂, 合成了两个系列的苯乙炔封端的酰亚胺预聚体. DSC测试结果表明, 此类预聚体具有比PETI-5更宽的加工窗口; 利用所合成的预聚体制成了具有较高热分解温度热固性交联PI薄膜. 结果表明, PI预聚体加工性能良好, 其交联后具有优异的力学和热学性能; 同时PEPA封端的预聚体树脂具有比PENA封端的树脂更为优异的综合性能.     

二氯二茂钛引发二苯乙炔聚合的研究

在高温下 ,二氯二茂钛受光照引发二苯乙炔聚合 ,得到结晶度为 95 %的聚二苯乙炔 .经红外、质谱、热分析、X光衍射、元素分析等方法 ,确定其结构为顺顺式螺旋刚性棒状结构 ,形成假六方晶系堆积 ,螺旋柱直径即螺旋轴间距为 1 46nm ,其特征红外吸收峰位于 1179cm-1和 115 6cm-1.在聚合引发阶段中止反应 ,分离出聚合中间体六苯基苯 .根据不同温度时聚合转化率与时间的关系曲线 ,测得聚合活化能为 2 6× 10 5J/mol.热分析表明 ,结晶聚二苯乙炔在 493K至 5 73K比较稳定 ;在 713K的吸热峰显示出破坏晶格的能量 .根据聚合反应诱导期长、中间体和聚合物的结构以及阻聚反应 ,推断聚合过程中二氯二茂钛受光照产生二氯化钛 ,催化二苯乙炔进行均相定向聚合 .结晶聚二苯乙炔电导率小于 10 -12 (Ωcm) -1.     

对苯醌二亚胺与对苯乙炔共聚物的金属配合物催化法合成与表征

在金属配合物的存在下,通过N,N′-二氯对苯醌二亚胺与1,4-二炔基-2,5-二（烷氧基）苯共聚,得到了一系列新型交替共聚物聚[N,N′-对苯醌二亚胺-1,4-二炔基-2,5-二（烷氧基）苯]（PAn-PPE）。采用FT-IR、1H-NMR、GPC、XRD、UV-Vis、PL、TGA等测试手段对共聚物的化学结构和性能进...     

Ligand‐free palladium‐catalyzed tandem pathways for the synthesis of 4,4‐diarylbutanones and 4,4‐diaryl‐3‐butenones under microwave conditions

Two efficient Pd‐catalyzed tandem pathways for the synthesis of 4,4‐diaryl‐2‐butanones and 4,4‐diaryl‐3‐buten‐2‐ones were elaborated. The first step in both procedures was the Heck coupling of methyl vinyl ketone (MVK) and various aryl iodides leading to 4‐aryl‐3‐buten‐2‐one with the yield of up to 92% in 1 hr. The second step performed with the same catalyst and a new portion of aryl iodide in the presence K₂CO₃ as a base produced 4,4‐diaryl‐3‐buten‐2‐ones in high yield. Reaction selectivity changed completely to saturated 4,4‐diaryl‐2‐butanones, reductive Heck products, when a tertiary amine was used instead of K₂CO₃. Due to the application of microwave irradiation (MW), the desired products were obtained in high yield in a short time (4 hr), using 0.5 mol% of the Pd (OAc)₂ catalyst without additional ligands.     

水溶性热塑性结晶高聚物聚环氧乙烷的合成及其性能的研究

环氧乙烷于双金属氧联醇盐或i-Bu_3Al-H_3PO_4-H_2O-二甲基苯胺(DMA)四元催化剂作用下在甲苯中呈均相聚合。二种催化剂均显示出高度活性,但前一体系的聚合速度较后一体系平缓。产物分子量可高达一百万。如用石油醇醚为溶剂,则转化率及分子量均下降。四元催化剂的最佳组成比为i-Bu_3Al:H_3PO_4:H_2O:DMA=1:0.17:0.17:0.10。产物溶于水并能模压成型。扯断强度随分子量增加而增加,可达100公斤/厘米~2。     

Catalyst‐Controlled Regiodivergent CH Borylation of Multifunctionalized Heteroarenes by Using Iridium Complexes

The regiodivergent C?H borylation of 2,5‐disubstituted heteroarenes with bis(pinacolato)diboron was achieved by using iridium catalysts formed in situ from [Ir(OMe)(cod)]₂/dtbpy (cod=1,5‐cyclooctadiene, dtbpy: 4,4′‐di‐tert‐butyl‐2,2′‐bipyridine) or [Ir(OMe)(cod)]₂/2 AsPh₃. When [Ir(OMe)(cod)]₂/dtbpy was used as the catalyst, borylation at the 4‐position proceeded selectively to afford 4‐borylated products in high yields (dtbpy system A). The regioselectivity changed when the [Ir(OMe)(cod)]₂/2 AsPh₃ catalyst was used; 3‐borylated products were obtained in high yields with high regioselectivity (AsPh₃ system B). The regioselectivity of borylation was easily controlled by changing the ligands. This reaction was used in the syntheses of two different bioactive compound analogues by using the same starting material.     

STUDIES OF MECHANISM OF 2-METHYLTHIOPHENE AND THIOPHENE FORMATION FROM N-PENTANE AND HYDROGEN SULPHIDE USING 14C

Abstract

The mechanism of 2-methylthiophene formation from n-pentane and hydrogen sulphide over Cr-containing oxide catalyst is studied by using the Kinetic-Isotope method. The experiments were carried out in pulse system in He as a carrier gas (535° and 3 atm.) using ¹⁴C-labelled pentene and n-pentane. The reaction products were analyzed by radiochromatography. It is shown the 2-methylthiophene formation from n-pentane and hydrogen sulphide proceeds largely via consecutive dehydrogenation of n-pentane to pentenes, pentadiene followed by interaction with hydrogen sulphide. Thiophene is largely as a result of C₄-hydrocarbon interaction with hydrogen sulphide. A general scheme of the mechanism of 2-methylthiophene and thiophene formation is suggested.     

Bipyridine‐Assisted Assembly of Au Nanoparticles on Cu Nanowires To Enhance the Electrochemical Reduction of CO2

We report a new strategy to prepare a composite catalyst for highly efficient electrochemical CO₂ reduction reaction (CO₂RR). The composite catalyst is made by anchoring Au nanoparticles on Cu nanowires via 4,4′‐bipyridine (bipy). The Au‐bipy‐Cu composite catalyzes the CO₂RR in 0.1 m KHCO₃ with a total Faradaic efficiency (FE) reaching 90.6 % at ?0.9 V to provide C‐products, among which CH₃CHO (25 % FE) dominates the liquid product (HCOO^?, CH₃CHO, and CH₃COO^?) distribution (75 %). The enhanced CO₂RR catalysis demonstrated by Au‐bipy‐Cu originates from its synergistic Au (CO₂ to CO) and Cu (CO to C‐products) catalysis which is further promoted by bipy. The Au‐bipy‐Cu composite represents a new catalyst system for effective CO₂RR conversion to C‐products.     

BINUCLEAR METAL CHELATES OF BISACETYLACETONE BIPHENYLDIHYDRAZONE

Abstract

Reaction of bihenyl-4,4′-tetrazonium ion with 2,4-pentanedione leads to 3,3′-(4,4′-biphenyldihydrazoni)bis-(2,4-pentanedione).The compound exists in the intramolecularly hydrogen bonded dihydrazone state. Copper(II), nickel(II) and palladium(II) complexes having the composition M₂L₂ have been synthesised and characterised. Ir, ¹H and ¹³C nmr and mass spectroscopic data clearly indicate the binucleating nature of the chelates in which the hydrogen bonded carbonyls and one of the hydrazono nitrogens of each pentanedione group are involved in bonding with the metal ion.     

Poly(Ether sulfone)s made from 4,4′-dihydroxystilbene and 4,4′-difluorodiphenylsulfone: Synthesis,crosslinking, and epoxidation with hydrogen peroxide

High molecular weight polymers from trans-4,4′-dihydroxystilbene, bisphenols, and 4,4′-difluorodiphenylsulfone were synthesized by a nucleophilic displacement reaction using DMAc as solvent in the presence of potassium carbonate. Characterization and crosslinking studies of these polymers were carried out by DSC, TGA, TMA, x-ray diffraction, and solution and solid NMR. It was found that all polymers can be crosslinked to some extent on heating to 350°C. We also studied the epoxidation of these polymers with hydrogen peroxide in the presence of methyltrioctylammonium tetrakis (diperoxotungsto) phosphate (3—) as the catalyst in a biphasic system. The epoxidized polymers are thermally cross-linkable. Very efficient crosslinking was obtained by heating the epoxidized polymers at 350°C under nitrogen. © 1995 John Wiley & Sons, Inc.     

A Water-Soluble Iridium Photocatalyst for Chemical Modification of Dehydroalanines in Peptides and Proteins

Dehydroalanine (Dha) residues are attractive noncanonical amino acids that occur naturally in ribosomally synthesised and post-translationally modified peptides (RiPPs). Dha residues are attractive targets for selective late-stage modification of these complex biomolecules. In this work, we show the selective photocatalytic modification of dehydroalanine residues in the antimicrobial peptide nisin and in the proteins small ubiquitin-like modifier (SUMO) and superfolder green fluorescent protein (sfGFP). For this purpose, a new water-soluble iridium(III) photoredox catalyst was used. The design and synthesis of this new photocatalyst, [Ir(dF(CF₃)ppy)₂(dNMe₃bpy)]Cl₃, is presented. In contrast to commonly used iridium photocatalysts, this complex is highly water soluble and allows peptides and proteins to be modified in water and aqueous solvents under physiologically relevant conditions, with short reaction times and with low reagent and catalyst loadings. This work suggests that photoredox catalysis using this newly designed catalyst is a promising strategy to modify dehydroalanine-containing natural products and thus could have great potential for novel bioconjugation strategies.