1,4-丁炔二醇与4,4′-二乙炔联苯共聚物的合成及表征研究

本文用(Ph_3P)_2PdCl_2为催化剂,合成了1,4-丁炔二醇(BD)与4,4-二乙炔联苯(DEBP)共聚物。对用不同比例的两种单体得到的共聚物测定了比重(d_4~(25)、溶胀度(θ_D)、最良溶剂及相邻两交联点之间的平均分子量(M_c)。实验表明,在两种单体摩尔比中,DEBP用量越多,共聚物中泡状微孔越多,颜色越淡,溶胀度和比重越小,交联度越大;DEBP/BD(摩尔比)大于1/5时,共聚物的最良溶剂为苯,溶度参数为9.15卡~(0.5)·cm~(-1.5),是1/10时,其最良溶剂为乙醇,溶度参数是12.7卡~0.5·cm~(-1.5)。对共聚物还做了红外光谱表征。     

4,4′-二乙炔二苯甲烷与苯乙炔的共聚及共聚物的表征研究

 本文做了4,4′-二乙炔二苯甲烷的本体热均聚和催化均聚,并用(Ph₃P)₂PdCl₂为催化剂做了4,4′-二乙炔二苯甲烷与苯乙炔的共聚,对均聚和共聚物中的不溶不熔组分测定了密度、溶胀度、Huggins参数以及交联点间的平均分子量M_c。实验表明,该交联聚合物的最良溶剂是四氢呋喃,溶度参数为9.9ca1^0.5。cm^-1.5,当用四氢呋喃为溶剂时的Huggins参数为0.34,并且在单体摩尔比中4,4′-二乙炔二苯甲烷用量越多,溶胀度越小,交联度越大。红外光谱分析表明,所有均聚及共聚物都为反式结构。     

4,4′-二乙炔二苯甲烷与苯乙炔的共聚及共聚物的表征研究

本文做了4,4′-二乙炔二苯甲烷的本体热均聚和催化均聚,并用(Ph_3P)_2PdCl_2为催化剂做了4,4′-二乙炔二苯甲烷与苯乙炔的共聚,对均聚和共聚物中的不溶不熔组分测定了密度、溶胀度、Huggins参数以及交联点间的平均分子量(?)_c。实验表明,该交联聚合物的最良溶剂是四氢呋喃,溶度参数为9.9ca1~0.5。cm~(-1.5),当用四氢呋喃为溶剂时的Huggins参数为0.34,并且在单体摩尔比中4,4′-二乙炔二苯甲烷用量越多,溶胀度越小,交联度越大。红外光谱分析表明,所有均聚及共聚物都为反式结构。     

一种新型物理交联型凝胶聚合物电解质的制备与表征

以甲氧基聚乙二醇甲基丙烯酸酯(MPEGM)和十六烷基聚乙二醇甲基丙烯酸酯(HPEGM)为单体, 三乙二醇二甲醚(TEGDME)为增塑剂, 与锂盐(高氯酸锂, LiClO₄)和光引发剂(安息香二甲醚, DMPA)复合制成光敏体系, 经紫外(UV)固化得到物理交联型凝胶聚合物电解质(GPE)薄膜. 用红外(IR)光谱、差热分析(DSC)、拉伸测试和交流阻抗(AC) 等方法对聚合物基体和电解质的性能进行了研究.结果表明: 当共聚物P(MPEGM-co-HPEGM)中HPEGM含量为50%(w)时, 十六烷基链段(C₁₆)在聚氧化乙烯(PEO)链段静电斥力的作用下发生聚集, 自组装形成了物理交联, 提高了共聚物的空间稳定性; 温度和电解质中各组分的含量对电导率均有较大的影响, 综合性能较好的电解质在30℃时电导率可达0.87×10^-3 S·cm^-1; 采用循环伏安法测得该电解质的电化学窗口为0~4.5 V (vs. Li/Li⁺), 可以满足锂离子电池的应用要求; 组装成的LiFePO₄/GPE/Li电池, 在30℃下以0.1 C和0.2 C倍率进行充放电测试, 首次放电容量分别为154.7和148.0 mAh·g^-1.     

硼氢化稀土-二乙基锌-甘油三元体系催化环氧丙烷与 CO2 共聚反应

 由硼氢化稀土、二乙基锌和甘油制备了三元体系 Ln(BH₄)₃•3THF-ZnEt₂-Gly (甘油) 用于催化环氧丙烷 (PO) 与 CO₂ 共聚反应, 详细考察了催化剂组成、不同稀土元素和溶剂性质对聚合反应的影响. 通过正交试验优化的催化剂组成和聚合条件为: Y(BH₄)₃•3THF-ZnEt₂-Gly (摩尔比 = 3:60:20) 催化剂, 乙二醇二甲醚溶剂, PO/Y 摩尔比 1000, [Y] = 6.67 mmol/L, p(CO₂) = 3.0 MPa, 80^oC, 6 h. 最高催化效率可达 4908 g /(mol•h); 碳酸酯含量为 95.7%, 数均分子量为 6.97x10⁴.     

二(2-吡啶甲酸)二(邻氟苄基)锡和一维链状4-吡啶甲酸三(邻氟苄基)锡的合成和晶体结构

μ-氧-双[三(邻氟苄基)锡]与2-吡啶甲酸或4-吡啶甲酸在苯溶剂中反应合成有机锡配合物二(2-吡啶甲酸)二(邻氟苄基)锡(1)和一维链状4-吡啶甲酸三(邻氟苄基)锡(2)，经X射线衍射方法测定了新化合物的晶体结构。配合物(1)属四方晶系，空间 群为I4₁/a，晶体学参数：a=1.562 0(3) nm，b=1.562 0(3) nm，c=1.984 7(4) nm，α=β=γ=90°，V=4.842 4(16) nm³，Z=8,D_c=1.594 Mg·m^-3， μ(Mo Kα)=11.06 cm^-1，F(000)=2 320，R₁=0.024 3，wR=0.062 5。配合物(2)属单斜晶系，空间群为P2₁/n，晶体学参数：a=0.869 8(3) nm，b=1.880 5(7) nm，c=1.475 1(5) nm，β=90.937(6)°，V=2.412 3(15) nm³，Z=4，D_c=1.564 Mg·m^-3，μ(Mo Kα)=11.07 cm^-1，F(000)=1 136，R₁=0.028 8，wR₂=0.057 9；配合物1为单体结构，中心锡为六配位畸变八面体构型。配合物2通过4-吡啶甲酸配体氮原子的桥联，形成五配位三角双锥型的链状结构。     

一维链状μ-氯(氧)-三苄基锡的合成和结构研究

合成了两种具有新型结构的苄基锡化合物：一维链状μ-氯-三苄基锡(1)和一维链状μ-氧-三苄基锡(2)，经X-射线方法测定了化合物的晶体结构。晶体结构(1)属正交晶系，空间群为P2₁2₁2₁，晶体学参数：a=0.855 3(3) nm，b=1.081 4(4) nm，c=1.968 1(7) nm，V=1.820 4(11) nm³，Z=4，D_c=1.560 g·cm^-3，μ(Mo Kα)=15.47 cm^-1，F(000)=856，R₁=0.059 7，wR₂=0.141 5。晶体结构(2)属正交晶 系，空间群为P2₁2₁2₁，晶体学参数：a=1.982 3(4) nm，b=1.089 1(2) nm，c=0.861 1(17) nm，V=1.859 0(6) nm³，Z=4，D_c=1.458 g·cm^-3， μ(Mo Kα)=13.76 cm^-1，F(000)=820，R₁=0.032 7，wR₂=0.064 8。配合物中锡原子均呈五配位畸变三角双锥构型。     

N，N′-双(2-吡啶乙基)二硫代草酰胺根桥联的三核铜(Ⅱ)配合物的合成及性质

Two Trinuclear copper(Ⅱ) complexes bridged with N,N′-Bis(2-pyridylethyl)-Dithiooxamidate, [Cu₃L₂](ClO₄)₂ (1) and [Cu₃L₂](NO₃)₂ (2) (H₂L=N,N′-Bis(2-pyridylethyl)-Dithiooxamide), have been synthesized, and characterized by elemental analyses, IR, UV-Visible spectra, conductance and EPR spectra. The variable temperature magnetic susceptibility for complex 1 has been measured in the temperature range of 1.5～298 K. Experimental data of magnetic susceptibility are successfully fit to theoretical value based on the spin Hamiltonian operator：(?), S₁=S₂=S₃=1/2, giving the magnetic exchange parameters of 2J=-221.6 cm^-1 and 2j=-15.8 cm^-1. This result indicates the presence of a strong antiferromagnetic spin exchange interaction between the Cu(Ⅱ) ions.     

纳米银对铕-吡啶-2,6-二羧酸配合物荧光增强效应的研究

研究了纳米银对分别以水、重水、乙醇和二甲基甲酰胺为溶剂的铕-吡啶-2,6-二羧酸(Eu(Ⅲ)DPA)配合物溶液的荧光增强效应. 研究结果表明,Eu(Ⅲ)DPA溶液中加入纳米银,电偶极跃迁(⁵D₀→⁷F₂)和磁偶极跃迁(⁵D₀→⁷F₁)发射强度先增强而后逐渐下降,⁵D₀→⁷F₂的荧光增强效率高于⁵D₀→⁷F₁的荧光增强效率. 在乙醇溶剂中纳米银对Eu(Ⅲ)DPA溶液的荧光增强效应最大. 在水或重水或乙醇溶剂中,Eu(Ⅲ)DPA的不对称率明显提高,而在二甲基甲酰胺溶剂中几乎不变. 分析认为,纳米银对Eu(Ⅲ)DPA溶液荧光的影响与纳米银表面等离子体共振与激发态荧光中心强烈耦合以及表面等离子体再吸收有关.     

以5-(6-羧酸-2-萘基)-间苯二羧酸为配体构筑的两个镉的金属-有机骨架化合物的合成、晶体结构及荧光性质

在溶剂热条件下,以不对称三羧酸5-(6-羧酸-2-萘基)-间苯二羧酸(H₃L)为配体合成了2个镉的金属-有机骨架化合物:{[Cd₃L₂(H₂O)₃]·6DMF}_n(1)和{[Cd₃L₂(H₂O)₄]·3DMA}_n(2)。通过X射线单晶衍射,粉末衍射,热重和红外光谱进行了结构表征。结构分析表明,1和2形成3,6-连接的三维结构,其拓扑符号分别为:(4⁵.6⁴.8⁶)(4³)₂和(6¹².8³)(6³)₂。此外,还对2个化合物进行了荧光分析。     

SYNTHESIS OF THE COPOLYMERS OF p-DIETHYNYLBENZENE WITH OTHER ACETYLENIC DERIVATIVE S INITIATED BY (Ph_3P)_2 PdCl_2

The copolymerization of p-diethynylbenzene (PDEB) with phenylacetylene (PhA), 4, 4'-diethynylbiphenyl (DEBP)or m-diethynylbenzene (MDEB) are studied by varying mole ratios of monomers. When the mole ratios of PDEB/PhA are less or equal to 1/5, the copolymers are soluble and fusible, but the other copolymers are insoluble and infusible. The results show that the good solvent of cross-linked copolymers is benzene and their solubility parameter is 9.15 cal~(0.5).cm(-1.5). And their swellability (θ_p), Huggins parameter (χ), density (d_4~(25)) and the average molecular weights between crosslinks (c) are measured. It is found that θp and c of copolymers are greater but d_4~(25) is less than that of respective homopolymers. IR spectra show that the copolymers have transoid configuration and small number of unreacted ethynyl groups exist in the copolymers. The mechanism about the polymerization or acetylenic derivatives initiated by (Ph_3P)_2PdCl_2 is discussed.     

1,4-丁炔二醇的均聚及与苯乙炔的共聚研究

<正> 炔类聚合物由于具有长链π体系的结构特点,理论上可作为结构型导电聚合物,这一领域的研究工作正在迅速展开。 1,4-丁炔二醇(BD)可用PdCl_2,ZnCl_2,(Ph_3P)_2PdCl_2等多种催化剂催化聚合,得到长链共轭的聚(1,4-丁炔二醇)(PBD)。苯乙炔(PA)可用热聚合,光聚合、电聚合、自由基聚合、等离子体聚合、催化聚合等聚合方法,得到长链共轭的聚苯乙炔     

苯乙烯－乙烯共聚物的合成及其结构性能的研究

用负载型钛系催化剂ＭｇＣｌ２／ＴｉＣｌ４，ＮｄＣｌ３／ＡｌＥｔ３（ＳＮ－１催化剂）制备出组份比例变化的苯乙烯－乙烯共聚产物，共聚产物通过溶剂萃取分离，＾１３Ｃ－ＮＭＲ，ＩＲ，动态粘弹谱进行表征，并初步进行了与聚苯乙烯共混作用的研究。结果表明，ＳＮ－１催化剂能有效地催化苯乙烯与乙烯共聚合，共聚产物为含有均聚聚苯乙烯的共聚复合物，其中约２５ｍｏｌ％的苯乙烯参加了共聚。共聚产物与ａＰＳ共混可明显提高ａＰ     

13C-NMR研究丁二烯-异戊二烯共聚合的竞聚率和共聚物的序列分布

 用¹³C-NMR方法研完了不同配料比的丁二烯-异戊二烯本体共聚和溶液共聚物的结构,定量计算出了共聚物二元组的浓度和数均序列长度,采用T(?)DO″S法计算出了本体共聚和溶液共聚的竞聚率,并证明各种共聚产物的序列分布都服从一级Markov统计模型。     

STUDIES ON THE REGULAR COPOLYMERS OF POLY (1, 4-PHENYLENETEREPHTHALAMIDE)

Two types of the regular copolymer of poly (1, 4-phenyleneterephthalamide) were synthesized by the low temperature solution polycondensation in NMP-CaCl_2 solvent system, using the piperazine or 2,5-dimethylpiperazine as the third components introduced in the main chain of poly (1, 4-phenyleneterephthalamide). The properties of copolymers were characterized by IR, SEM, X-RAY diffraction, polarizing microscopy, TGA and solubilities.Experimental results showed that the copolymers had good solubility and thermal stability, the concentrated sulfuric acid (～98% ) solution of regular PPTA copolymers had liquid crystalline proper-     

SUBSTITUENT CHEMICAL SHIFT (SCS) AND THE SEQUENCE STRUCTURE OF ETHYLENE-VINYL ALCOHOL COPOLYMERS

Three ethylene-vinyl alcohol copolymers were studied by means of the substituent chemical shift (SCS) method. The SCS parameters of hydroxy (-OH) in two different solvents were obtained: in deuterium oxide/phenol (20/80 W/W ) the parameters are S_1 = 42.77±0.08ppm, S_2 = 7.15±0.06 ppm, S_3 (s)= -4.08±0.02ppm, S_3 (t) =-3.09±0.20ppm,S_4 = 0.48±0.03ppm, S_5 = 0.26±0.05ppm. In o-dichloro-benzen-d_4 S_1(s)=44.79±0.61ppm, S_2=7.40±0.00ppm, S_3(s)=-4.51±0.17ppm, S_3(t)=-3.13 ±0.00 ppm, S_4 =0.63±0.04ppm, S_5=0.36±0.00ppm.Simultaneously the ~(13)CNMR spectra of EVA copolymers were assigned by using the SCS parameters obtained.     

ACID DISSOCIATION BEHAVIOR OF 2, 3- AND 2, 3, 9,lO-METHYL- OR CYCLOHEXYL-SUBSTITUTED CYCLAMS,THEIR COMPLEXATION BEHAVIOR WITH COPPER@) AND THE AXIAL SOLVENT SPECTRUM OF THEIR COMPLEXESINTERACTION EFFECT ON THE LIGAND-FIELD

Abstract

Stability constants of Cu(Il)-complexes for 1, 4, 8, 11-tetra-azacyclotetradecane (cyclam) analogs with periphery substituted [14]aneN₄-ring, 2, 3-tetramethyl-, 2, 3, 9, 10-octamethyl-, 2, 3-cyclohexyl, and 2, 3, 9, 10-dicyclohexyl-cyclams have been determined at 25°C in aqueous solution. The UV-Vis absorption spectra of their complexes, ([Cu(L)] (C1O₄)₂), were measured in water and some typical organic solvents (methanol, acetone, propylene carbonate, formamide, N, N-dimethylformamide, and dimethylsulfoxide). A good linear relationship was found between the stability constant logK_CuL) and the difference between the wavenumber of maximum absorption in water and in the organic solvents (δλ_max ^?1 (W-S)). The value of logK_CuL at δλ_max ^?1(W-S) = 0 not only shows a linear relation to solvent parameters, donor number and dielectric constant, but also to the enthalpy of transfer of ClO₄ ^? from water to the organic solvents. The value is proposed as a new solvent parameter ‘Kλlue’ to be used as an index for solvent-effects on Cu(II)-complexes of cyclam analogs. The increasing order of the new parameter (log scale) is as follows; DMF(27.24)>DMSO(27.14)>FA(26.82)>MeOH(26.27)>PC(25.75)>AC(24.71). Another meaning of the new parameter is assumed from connection of the potentiometric data with spectrometric data. The solvent effects on stability and the UV-Vis spectra are assumed to be caused by perturbation of the D_{4 h} or axially-elongated ligand field through axial approach of solvent to the Cu(II)-complexes and by formation of a solvent-separated ion pair between a solvated Cu(lI)-complex cation and counter anion (ClO₄)     

NON-LINEAR LEAST SQUARE CURVE FITTING OF COPOLYMERIZATION MODELS TO THE ALTERNATING TRIAD FRACTION OF COPOLYMERS OF STYRENE AND CITRACONIC ANHYDRIDE,AND COPOLYMERS OF STYRENE AND MALEIC ANHYDRIDE PREPARED IN N,N-DIMETHYLFORMAMIDE

Copolymers of styrene (ST) and citraconic anhydride (α-methylmaleic anhydride) (CA) were prepared in a very polar solvent, N,N-dimethylformamide (DMF), at 50.0°C with AIBN. The monomer unit triad fractions were determined by ¹³C NMR in acetone-d ₆ solution. Non linear least square (NLLS) curve fitting was performed for the copolymerization models of the terminal model, the penultimate unit effect model, the complex participation model, the complex dissociation model, and the so-called comppen model. The theoretical equations for the ST-centered alternating triad mole fraction were fitted by NLLS minimization routine to the triad fraction data of the ST-CA copolymers and that of the ST-maleic anhydride (MA) copolymers prepared in identical polymerization conditions. It was found that for rigidly alternating copolymers of ST-MA, the difference among the copolymerization models disappeared and all models merged together. The difference among the copolymerization models were somewhat more apparent for less alternating copolymers of ST-CA copolymers. The sum of squares values indicated that the copolymerization models, which involved some complex participation, fit the data better with the comppen model. This was a combination of a complex participation and penultimate unit effects, which performed best.