燃料电池用聚乙烯醇基碱性聚合物电解质膜的制备及其性能

通过在不同浓度KOH溶液中进行掺杂,制备出了聚乙烯醇(PVA)、聚乙烯醇/聚乙烯吡咯烷酮(PVA/PVP)和聚乙烯醇/聚乙二醇二甲醚(PVA/PEGDE)碱性聚合物电解质膜详细考察了膜的外观形貌、微观结构、热稳定性、离子电导率和化学稳定性等.结果表明,PVA与PVP以及PEGDE具有很好的相容性,所制备的复合膜断面致密...     

聚乙烯醇/聚乙烯吡咯烷酮碱性复合膜的制备及其性能

通过在不同浓度KOH溶液中进行掺杂,制备出了聚乙烯醇/聚乙烯吡咯烷酮(PVA/PVP)碱性聚合物电解质膜.详尽考察了膜的组成、微观结构、热稳定性、离子电导率和甲醇吸收率.结果表明,PVA与PVP两者具有较好的相容性,当m(PVA)∶m(PVP)=1∶0.5时,膜断面致密、均匀,未发生大尺度相分离.PVP的混入可以极大提高复合膜的电导率和热稳定性.当m(PVA)∶m(PVP)=1∶1时,复合膜的电导率可达2.01×10-3 S.cm-1.PVA/PVP/KOH膜的甲醇吸收率随温度的升高没有明显变化,100℃时其甲醇吸收率仅为同条件下Nafion 115膜的1/4.这表明该复合膜有望作为一种新型的碱性直接甲醇燃料电池用固体电解质膜且可提高膜的使用温度.     

用于燃料电池的季铵基团的PVA/PAADDA碱性聚合物电解质膜的制备及稳定性

通过聚合物共混法成功地制备出了具有化学交联结构的聚乙烯醇/二甲基二烯丙基氯化铵和丙烯酰胺共聚物(PVA/PAADDA)碱性聚合物电解质膜。采用傅里叶红外分析（FTIR）、扫描电镜（SEM）、热重分析（TGA）和交流阻抗等方法详细考察了PVA/PAADDA膜的分子结构、微观形貌、热稳定性、耐碱稳定性、尺寸稳定性和电导率。红外分析结果表明,PAADDA成功地混入聚合物基体中。SEM分析结果表明,当m(PVA):m(PAADDA)=1:1时,膜可观察到明显的微相分离。TGA结果表明,混入PAADDA后膜的热稳定性没有明显降低,并且在210 oC之前能保持很好的热稳定性。PVA/PAADDA膜在经过高温、高浓度碱溶液（80 oC, 6 mol?L-1）处理后,仍表现出很好的耐碱稳定性。同时,由于膜内形成致密的内互交联网络结构,PVA/PAADDA膜在60 oC水中处理300 h后也能表现出优良的尺寸稳定性和电导率稳定性。此外,膜的甲醇吸收率随着温度的升高没有明显变化,90 oC时甲醇吸收率仅为同条件下Nafion115膜的1/5。     

用于聚合物镍氢电池的新型PVA/SiO2碱性微孔聚合物电解质

采用溶胶凝胶法,结合相转移法和碱液活化法制备了PVA/SiO2碱性微孔聚合物电解质,通过SEM、XRD、交流阻抗法和循环伏安法表征了电解质的结构与电化学性能.研究表明,PVA/5ωSiO2(ω为质量分数)共混膜上的微孔大小合适,聚合物电解质的离子电导率最大可达1.62×10-2 S·cm-1,电化学稳定窗口2V以上;将PVA/SiO2碱性微孔电解质组装成聚合物镁基镍氢电池,与传统镍氢电池相比,循环稳定性大大增加.     

用于聚合物镍氢电池的新型PVA/SiO2碱性微孔聚合物电解质（英文）

采用溶胶凝胶法,结合相转移法和碱液活化法制备了PVA/SiO2碱性微孔聚合物电解质,通过SEM、XRD、交流阻抗法和循环伏安法表征了电解质的结构与电化学性能.研究表明,PVA/5ωSiO2(ω为质量分数)共混膜上的微孔大小合适,聚合物电解质的离子电导率最大可达1.62×10-2 S cm-1,电化学稳定窗口2 V以上;将PVA/SiO2碱性微孔电解质组装成聚合物镁基镍氢电池,与传统镍氢电池相比,循环稳定性大大增加.     

PVA-膨润土-KOH-H2O复合碱性聚合物电解质的制备与表征

以聚乙烯醇(PVA)与膨润土(bentonite)和氢氧化钾为原料, 采用溶液浇铸法制备了PVA-膨润土-KOH-H2O复合碱性聚合物电解质膜. 运用X衍射(XRD)、扫描电镜(SEM)和循环伏安(CV)等技术对复合膜进行了表征, 分析了膨润土对聚合物膜电导率的影响. 结果表明, 膨润土对电解质的导电性能具有双重作用: 一方面膨润土本身会阻塞PVA内部结构中的部分离子通道, 导致复合电解质的电导率降低; 另一方面, 膨润土有助于体系中KOH含量的增加, 同时PVA-膨润土相界面高导电性缺陷层的形成有助于体系电导率的提高. 当体系水的质量分数较低时, 复合电解质体系电导率存在极大值; 当w(H2O)为65%时, 则观察到电导率的线性增加趋势; 电解质最高室温电导率达0.110 S·cm-1. XRD图谱显示适当配比的复合膜中PVA呈无定形态; SEM结果证实了适当配比的复合膜中存在大量微米级孔径的微孔通道. 循环伏安曲线表明PVA-膨润土-KOH-H2O碱性聚合物电解质膜有约2.0 V的较宽电化学稳定窗口.     

Gemini型碱性离子液体的制备及其在吡啶功能化PVA阴离子膜中的应用

通过两步法合成具有Gemini结构的碱性十二烷基吗啉离子液体([Nbmd]OH).并将制得的离子液体引入吡啶功能化聚乙烯醇(PVA-FP)为基质的阴离子交换膜制备过程中,通过流延法制备PVAFP/[Nbmd]OH复合膜.借助傅里叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)、X射线衍射(XRD)、交流阻抗(AC)、热重分析(TGA)及机械性能测试等对复合膜的结构及理化性能进行表征.结果表明,该系列复合膜形貌平整均一,吡啶基团的引入增强了PVA基质膜的热稳定性及耐碱稳定性.[Nbmd]OH离子液体的引入,在提供更多阳离子活性点位的同时,降低了复合膜结晶度,提高了电导率,改善了机械性能.其中,当质量比m(PVA)∶m([Nbmd]OH)=1∶2.5时,复合膜的热分解温度较PVA膜提高75oC;70oC时电导率达到4.42×10~(-2)S?cm~(-1);在80oC,6 mol/L KOH溶液中进行加速老化实验,浸泡400 h后电导率为初始电导率的1.6倍左右,表现出优异的耐碱稳定性;在30oC,3 mol/L甲醇溶液中甲醇透过率仅为Nafion~?-117膜的2.5%~5%,表现出很好的阻醇性能.     

PVA-CMC-KOH-H2O碱性聚合物电解质研究

由聚乙烯醇(PVA)与羧甲基纤维素钠(CMC)制备PVA-CMC-KOH-H2O碱性聚合物电解质膜,应用交流阻抗、循环伏安、差热分析和红外光谱等实验方法表征、研究其性能.结果表明,该碱性聚合物电解质的室温电导率可达到10-2S.cm-1数量级,在不锈钢惰性电极上的电化学稳定窗口约为1.6 V.另外,还研究了聚合物电解质膜中KOH、H2O和CMC对体系电导率的影响以及PVA-CMC-KOH-H2O碱性聚合物电解质在N i/MH电池中的初步应用.初步结果表明,由PVA-CMC-KOH-H2O聚合物电解质组装的N i/MH电池,其低倍率放电性能较好.     

用于燃料电池的聚乙烯醇/纤维素/聚乙二醇碱性阴离子交换复合膜的制备及性能

通过对聚乙烯醇(PVA)/季铵化羟乙基乙氧基纤维素(QHECE)共混膜进行聚乙二醇(PEG)聚塑化改性, 采用物理-化学交联联用法制备了PVA/QHECE/PEG碱性阴离子交换复合膜. 通过交流(AC)阻抗、 傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)、 热重分析(TGA)、 气相色谱(GC)和拉伸实验等手段考察了不同PEG添加量对膜的离子电导率、 分子结构、 微观形貌、 热稳定性、 力学强度、 甲醇渗透率和耐碱稳定性等性能. 结果表明, PEG的加入(除最小比例外)提高了膜的离子电导率和力学强度并使其柔韧性增大. 同时, 膜的热稳定性比未添加PEG时提高了40℃. 将PVA/QHECE/PEG膜在80℃, 6 mol/L KOH浓碱溶液中浸渍处理264 h, 膜的电导率从1.06×10^-3 S/cm提高到3.88×10^-3 S/cm, 而膜的外观和力学强度及含水率未发生明显变化, 表明该膜具有很好的耐碱化学稳定性. 此外, 以3 mol/L甲醇溶液为测试目标, 膜的甲醇渗透率<10^-7 cm²/s, 仅为商业用Nafion^®膜的1/20~1/40.     

化学交联聚乙烯醇改性纤维素碱性阴离子交换复合膜的制备与性能

高稳定性碱性阴离子交换膜的制备已成为碱性固体电解质膜研究领域的一大热点.本文通过聚乙烯醇化学交联改性制备出了季铵化羟乙基乙氧基纤维素碱性阴离子交换膜（PVA/QHECE）.采用傅里叶变换红外（FTIR）光谱、热重（TG）分析、交流（AC）阻抗等方法考察了复合膜的分子结构、热稳定性、耐碱稳定性及离子电导率等性能.详尽考察了交联时间、交联剂含量、聚合物组成对成膜力学强度、含水率以及OH^-电导率的影响.实验结果表明:随着交联时间的增加,膜的溶胀率降低,力学强度随之增强,而离子电导率随膜含水率的降低没有发生明显变化,室温下OH^-的电导率在3.26×10^-4-4.44×10^-4S·cm^-1范围内变化.热重分析结果显示:掺入42.9%的QHECE时,膜的热分解温度达260℃.此外,将PVA/QHECE膜在6 mol·L^-4 KOH浓碱溶液中80℃浸渍处理168 h,膜的电导率从4.90×10^-4S·cm^-1提高到9.68×10^-4S·cm^-1,而膜的外观和力学强度以及含水率未发生明显变化,这一结果表明该膜具有很好的耐碱化学稳定性,有望作为一种新型的碱性燃料电池用离子交换膜.     

Alkaline Zn-air and Al-air cells based on novel solid PVA/PAA polymer electrolyte membranes

High ionic conducting solid polymer electrolyte membranes (SPEM) had been successfully prepared from poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA). The solution casting method yielded highly hydrophilic membranes with uniform structure that were suitable for electrochemical applications. The room temperature ionic conductivity of the alkaline PVA/PAA polymer electrolyte membranes was in the range of 0.142–0.301 S cm⁻¹ depending on the composition. The cyclic voltammetry analysis was carried out using Zn|SPEM|Zn and Al|SPEM|Al cells. The analysis results revealed the excellent electrochemical stability of these newly developed alkaline solid PVA/PAA polymer electrolyte membranes. Metal-air fuel cells were also prepared from the alkaline solid PVA/PAA polymer electrolyte membranes. The electrochemical cell performance was evaluated based on Zn-air and Al-air cells at C/10 and C/5 discharge rates. The experimental results exhibited high percent of utilization for metal powders at room temperature. It was up to 90% for Zn-air cell when assembled with PVA:PAA = 10:7.5 polymer electrolyte membrane and discharged at C/10 rate. The power density could be as high as 50 mW cm⁻² at room temperature. However, the cell percent utilization was reduced to 73% with the same composition electrolyte membrane when C/5 discharge rate was tested.     

聚乙烯醇/纳米纤维素复合膜的渗透汽化性能及结构表征

将聚乙烯醇/纳米纤维素(PVA/NCC)复合膜应用于乙醇-水混合溶液的渗透汽化脱水过程,探讨了纳米纤维素对膜的溶胀性能、机械性能和渗透汽化性能的影响; 利用原子力显微镜(AFM)探测了纳米纤维素的形貌特征; 采用傅里叶变换红外光谱仪(FTIR)、扫描电镜(SEM)、差示扫描量热仪(DSC)和热重分析仪(TGA)对膜结构...     

High-performances membranes for pervaporation I. Poly(vinyl alcohol)–poly(N-vinyl pyrrolidone) blends

Dense membranes were prepared from poly(vinyl alcohol)–poly(N-vinyl pyrrolidone) (PVA–PVP) blends of different compositions and studied in swelling and dehydration by pervaporation of three organic solvents contaminated by 5 wt% water. The swelling generally increases with the PVP content. No extraction occurs in water–tetrahydrofuran (THF) and water–methyl ethyl ketone (MEK) mixtures. In ethanol containing 10 wt% of water, there is no extraction for blends containing less than 40 wt% PVP and an increasing extraction beyond this PVP content. The pervaporation flux of the water–ethanol mixture increases drastically at the same threshold whereas the water permselectivity falls to a low level. The values of the diffusion and permeability coefficients determined from transient permeation of the test water–ethanol mixture exhibit a similar sudden increase at the same PVP content threshold. This singular behavior of the blend membranes is interpreted by a strong affinity of the PVP component to ethanol, combined with a disappearance of crystallites in the blend at this threshold. Consequently the amorphous membrane can swell freely according to the affinity of the PVP component, leading to the observed behavior.     

氯化镁增塑改性聚乙烯醇

以氯化镁为增塑剂, 采用流延法制备了增塑改性聚乙烯醇(PVA). 研究了氯化镁与PVA的相互作用以及氯化镁增塑改性PVA的结晶性能、 热性能和机械性能. 研究结果表明, 氯化镁能与PVA大分子发生较强的相互作用, 从而破坏PVA分子链内和链间的氢键, 降低PVA的结晶度. 氯化镁对PVA的热性能影响显著, PVA在加入氯化镁后的热分解过程由纯PVA的两段失重过程转变成三段失重过程. 氯化镁可有效增塑PVA, 其玻璃化转变温度降低, 拉伸强度下降, 断裂伸长率上升, 储能模量下降.     

Poly(vinyl alcohol)/poly(methyl methacrylate) blend membranes for pervaporation separation of water + isopropanol and water + 1,4-dioxane mixtures

Pervaporation (PV) separation of water + isopropanol and water + 1,4-dioxane mixtures has been attempted using the blend membranes of poly(vinyl alcohol) (PVA) with 5 wt.% of poly(methyl methacrylate) (PMMA). These results have been compared with the plain PVA membrane. Both plain PVA and PVA/PMMA blend membranes have been crosslinked with glutaraldehyde in an acidic medium. The membranes were characterized by differential scanning calorimetry and universal testing machine. Pervaporation separation experiments have been performed at 30 °C for 10, 15, 20, 30 and 40 wt.% of feed water mixtures containing isopropanol as well as 1,4-dioxane. PVA/PMMA blend membrane has shown a selectivity of 400 for 10 wt.% of water in water + isopropanol feed, while for water + 1,4-dioxane feed mixture, membrane selectivity to water was 104 at 30 °C. For both the feed mixtures, selectivity for the blend membrane was higher than that observed for plain PVA membrane, but flux of the blend membrane was lower than that observed for the plain PVA membrane. Membranes of this study are able to remove as much as 98 wt.% of water from the feed mixtures of water + isopropanol, while 92 wt.% of water was removed from water + 1,4-dioxane feed mixtures at 30 °C. Flux of water increased for both the feed mixtures, while the selectivity decreased at higher feed water concentrations. The same trends were observed at 40 and 50 °C for 10, 15 and 20 wt.% of water mixtures containing isopropanol as well as 1,4-dioxane feed mixtures, which also covered their azeotropic composition ranges. Membrane performance was studied by calculating flux (J_p), selectivity (), pervaporation separation index (PSI) and enrichment factor (β). Permeation flux followed the Arrhenius trend over the range of temperatures investigated. It was found that by introducing a hydrophobic PMMA polymer into a hydrophilic PVA, the selectivity increased dramatically, while flux decreased compared to plain PVA, due to a loss in PVA chain relaxation.     

Modification and characterization of semi-crystalline poly(vinyl alcohol) with interpenetrating poly(acrylic acid) by UV radiation method for alkaline solid polymer electrolytes membrane

Semi-crystalline poly(vinyl alcohol) was modified by UV radiation with acrylic acid monomer to get interpenetrating poly(acrylic acid) modified poly(vinyl alcohol), PVAAA, membrane. The stability of various PVAAA membranes in water, 2 M CH₃OH, 2 M H₂SO₄, and 40 wt% KOH aqueous media were evaluated. It was found that the stability of PVAAA membrane is stable in 40 wt% KOH solution. The PVAAA membranes were characterized by differential scanning calorimetry, X-ray diffraction, and thermogravimetry analysis. These results show that (1) the crystallinity in PVAAA decreased with increasing the content of poly(acrylic acid) in the PVAAA membranes. (2) The melting point of the PVAAA membrane is reduced with increasing the content of poly(acrylic acid) in the membrane. (3) Three stages of thermal degradation were found for pure PVA. Compared to pure PVA, the temperature of thermal degradation increased for the PVAAA membrane. The various PVAAA membranes were immersed in KOH solution to form polymer electrolyte membranes, PVAAA-KOH, and their performances for alkaline solid polymer electrolyte were conducted. At room temperature, the ionic conductivity increased from 0.044 to 0.312 S/cm. The result was due to the formation of interpenetrating polymer chain of poly(acrylic acid) in the PVAAA membrane and resulting in the increase of charge carriers in the PVA polymer matrix. Compared to the data reported for different membranes by other studies, our PVAAA membrane are highly ionic conducting alkaline solid polymer electrolytes membranes.     

一种高电导率PVA聚合物电解质的制备与表征

A type of polymer-in-salt electrolyte composed of poly( vinyl alcohol), KOH and water was prepared by a solution casting method. X-ray diffraction proves that the high concentration of KOH in the electrolyte is in an amorphous state. The ionic conductivities of the PVA-KOH-H2O electrolytes increased as the concentration of KOH increased, and the alkaline electrolyte with PVA/KOH 1/3 (mass ratio) exhibited the highest ionic conductivity of 0. 15 S/cm at room temperature, as measured by electrochemical impedance spectroscopy. The temperature dependence of the conductivity is found to be in agreement with the Arrhenius equation. The potential stability window at the metal/electrolyte interface was of 1.4 V for the nickel electrode determined by cyclic voltammetry.