用于燃料电池的聚乙烯醇/纤维素/聚乙二醇碱性阴离子交换复合膜的制备及性能

通过对聚乙烯醇(PVA)/季铵化羟乙基乙氧基纤维素(QHECE)共混膜进行聚乙二醇(PEG)聚塑化改性, 采用物理-化学交联联用法制备了PVA/QHECE/PEG碱性阴离子交换复合膜. 通过交流(AC)阻抗、 傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)、 热重分析(TGA)、 气相色谱(GC)和拉伸实验等手段考察了不同PEG添加量对膜的离子电导率、 分子结构、 微观形貌、 热稳定性、 力学强度、 甲醇渗透率和耐碱稳定性等性能. 结果表明, PEG的加入(除最小比例外)提高了膜的离子电导率和力学强度并使其柔韧性增大. 同时, 膜的热稳定性比未添加PEG时提高了40℃. 将PVA/QHECE/PEG膜在80℃, 6 mol/L KOH浓碱溶液中浸渍处理264 h, 膜的电导率从1.06×10^-3 S/cm提高到3.88×10^-3 S/cm, 而膜的外观和力学强度及含水率未发生明显变化, 表明该膜具有很好的耐碱化学稳定性. 此外, 以3 mol/L甲醇溶液为测试目标, 膜的甲醇渗透率<10^-7 cm²/s, 仅为商业用Nafion^®膜的1/20~1/40.     

分光光度法测定大气降水中过氧化氢

在磷酸介质中,过氧化氢氧化I^-形成I₃^-络阴离子;在脂肪醇聚氧乙烯醚硫酸钠（AOES）中I₃^-进一步与亚甲基蓝作用形成离子缔合物,最大吸收波长位于530 nm处。过氧化氢浓度与吸光度呈线性关系,据此建立了分光光度法测定大气降水中过氧化氢含量的方法。过氧化氢的浓度在1.7×10^-6～2.5×10^-5mol·L^-1范围内遵守比耳定律,表观摩尔吸光率为4.12×10⁴ L·mol^-1·cm^-1,方法的检出限（3s/k）为2.1×10^-7 mol·L^-1。方法用于大气降水中过氧化氢的测定,加标回收率在94.3%～105%之间,测定值的相对标准偏差（n=5）在1.4%～3.2%之间。     

基于铕离子-四环素-草甘膦荧光增强体系结合分子印迹固相萃取测定环境样品中草甘膦的残留量

提出了基于铕离子-四环素-草甘膦荧光增强体系结合分子印迹固相萃取测定环境样品中草甘膦残留量的方法。以正硅酸乙酯为溶胶-凝胶功能单体,在pH 1.0的硅溶胶-凝胶体系中制备了草甘膦分子印迹固相萃取膜,用于环境水和土壤样品的前处理。将前处理后的样品溶液与1.5×10^-2 mol·L^-1 EuCl₃溶液、3.0×10^-3 mol·L^-1四环素溶液和100 mmol·L^-1硼酸盐缓冲溶液(pH 10.0)按照一定比例混合,静置反应3 min;以403 nm为激发波长,根据体系在615 nm发射波长处的荧光强度增加值ΔF计算草甘膦的含量。结果表明：在较强碱性条件下,草甘膦的加入使体系在615 nm处的荧光强度显著增强;草甘膦浓度的对数在5.0×10^-8～1.5×10^-4 mol·L^-1内与体系ΔF值呈线性关系,检出限(3s/k)为1.0×10^-8 mol·L^-1     

自交联聚乙烯亚胺-聚砜高温质子交换膜研究

为了制备出兼具高电导率和优异力学性能的高温质子交换膜,本工作采用化学自交联的方法将含氮功能基团聚乙烯亚胺（PEI,平均分子量200）接枝到氯甲基化聚砜（CMPSF）高分子链上制备磷酸掺杂型高温质子交换膜的基膜（PEI-PSF）.其中,PEI上的含氮功能基团既作为磷酸吸附位点,使高温质子交换膜获得高的质子传导率,同时又作为交联位点与CMPSF高分子链上的苄氯基团发生自交联反应,使聚合物膜具有优良的力学性能.傅里叶变换红外光谱和X-射线光电子能谱测试结果表明,CMPSF高分子链上的苄氯基团与PEI上的含氮功能基团发生完全反应,且随着聚砜氯甲基化程度的增加,膜中引入的PEI含量相应增加,进而提升了PEI-PSF膜的磷酸掺杂水平.氯甲基化程度为58%的PEI-PSF膜（PEI-PSF-58）磷酸吸附量达到122 wt%,在180℃无水条件下质子电导率达到3.4×10^-2 S·cm^-1,同时该复合膜拉伸强度达到30 MPa.基于磷酸掺杂的PEI-PSF-58复合膜的高温质子交换膜燃料电池在150℃干气条件下的输出峰功率达到200 mW·cm^-2,并且在78 h的测试时间内展示出了良好的稳定性.     

SIFSIX-3-Ni膜的制备及氢气分离性质

利用(NH₄)₂SiF₆修饰大孔玻璃基底后, 在溶剂热条件下制备了SIFSIX-3-Ni膜, 并研究了温度和浓度对制备SIFSIX-3-Ni膜的影响. 能谱分析(XPS)结果表明大孔玻璃表面引入了氟元素. SIFSIX-3-Ni膜的粉末X射线衍射(PXRD)峰位置和模拟结果一致, 表明成功制备出SIFSIX-3-Ni膜. 从扫描电子显微镜(SEM)照片中观察到膜连续均匀, 厚度约为20 μm. 热重分析(TGA)结果表明, 活化前的膜没有客体分子. 单组分测试结果表明, 膜的H₂, CO₂和N₂渗透量分别为6.83×10 ^-6, 7.42×10 ^-7和8.89×10 ^-7 mol·m ^-2·s ^-1·Pa ^-1, H₂/CO₂和H₂/N₂的理想分离比分别为9.20和7.68. 在连续测试5 h后, H₂, CO₂和N₂渗透量基本保持不变, 表明SIFSIX-3-Ni膜具有很好的稳定性.     

铁(Ⅲ)-硫氰酸根-乙基罗丹明B缔合体系微乳液分光光度法测定铝合金中铁

提出了微乳液分光光度法测定铝合金中铁含量的方法。在比色管中,先后加入0.5 mol·L^-1硫酸溶液3.00 mL、铁（Ⅲ）标准溶液,2 mol·L^-1硫氰酸钾溶液3.00 mL、5 g·L^-1阿拉伯树胶溶液0.8 mL、微乳液0.70 mL及1×10^-3 mol·L^-1乙基罗丹明B溶液3.00 mL使反应生成铁与硫氰酸盐的络阴离子和乙基罗丹明B的缔合物。微乳液和阿拉伯树胶对此显色体系具有显著的增溶作用。铁（Ⅲ）的质量浓度在0.026～0.36 mg·L^-1范围内与其吸光度呈线性关系。反应体系的吸收峰位于波长620 nm处,在此波长条件下测定其表观摩尔吸光率为1.08×10⁵ L·mol^-1·cm^-1。方法用于测定铝合金试样中铁量,测定值的相对标准偏差（n=5）小于2%。     

分子凝胶电解质的电导率研究

凝胶因子4,4'-二(硬脂酰胺基)二苯醚(BSDE)在水和非水介质(如二甲基甲酰胺、二甲基亚砜、碳酸丙烯酯等)中利用非共价键相互作用自组装成有序的三维纤维网络结构,使介质凝胶化.该凝胶被称之为分子凝胶.同样,BSDE也能使锂盐溶液凝胶化,制备一种新型分子凝胶电解质.水分子凝胶锂离子电解质的室温离子电导率达到10^-1～10^-2S·cm^-1,碳酸丙烯酯分子凝胶锂离子电解质的室温离子电导率也能达到10^-2～10^-3S·cm^-1.分子凝胶的离子电导率研究表明,锂盐在凝胶中的行为和其在溶液中的行为相似.在-35℃的低温下,分子凝胶的电导率与其溶液相比约低1～2个数量级.     

双(三氟甲基磺酰)亚胺钠基聚合物电解质在固态钠电池中的性能

采用简单的溶液浇铸法制备出由双（三氟甲基磺酰）亚胺钠（NaTFSI）/聚氧乙烯（PEO）构筑的固态聚合物电解质（SPE）,并针对其相转变、结晶性、热稳定性、电导率以及电化学稳定性等基础理化及电化学性质进行了系统表征。结果表明,NaTFSI/PEO（[EO]/[Na⁺]=15）SPE具有相对高的电导率（σ ≈ 10^-3 S·cm^-1,80℃）、高的耐氧化能力（4.86 V vs Na⁺/Na）和热稳定性高达350℃。电池测试结果表明,该NaTFSI基SPE不仅对金属钠电极能够呈现出优异的界面稳定性,而且在Na|SPE|NaCu_1/9Ni_2/9Fe_1/3Mn_1/3O₂电池中展现出良好的循环和倍率性能。     

Temperature effect on the kinetics of persulfate oxidation of p-chloroaniline

The kinetics of heat-facilitated persulfate oxidation of p-chloroaniline（PCA） in aqueous solutions was measured at five different temperature conditions and at four different oxidant concentrations.The PCA degradation was found to follow a pseudo-first-order decay model when the persulfate was excessive.The pseudo-first-order rate constants of PCA degradation by persulfate（50 mmol/ L） at pH 7.0 are 0.12×10^-4,0.28×10^-4,0.43×10^-4,0.83×10^-4,1.32×10^-4 s^-1 at 10,20,30,40 and 50℃,respectively. Under the above reaction conditions,the reaction has activation energy of 49.97 kJ/mol.The observed rate was found to be function of temperature and oxidant concentration.Raising temperature and increasing persulfate concentration can significantly accelerate the PCA degradation.     

介孔SiO2孔道内Gemini分子有序自组装构筑正相胶束辅助传递OH-离子

利用Gemini型阳离子表面活性剂(顺丁烯二酸二乙酯撑基双[辛烷基二甲基氯/溴化铵], G_8-2-8)在有机反离子水杨酸根(Sal^-)的诱导作用下, 于介孔SiO₂孔道内有序组装, 构筑表面带有季铵基团的正相蠕虫胶束. 胶束外表面有序排布的季铵基团与介孔SiO₂孔道内壁布满的硅羟基共同作用形成环形保水腔室, 即构筑了OH^-传递的有序通道. 通过对G_8-2-8/NaSal 胶束体系的流变学性质研究, 结果表明, 胶束网络结构已经形成. 将G_8-2-8/NaSal胶束网络形成过程引入聚砜(PSF)体系中, 制备出有序OH^-迁移通道的高耐碱性的阴离子导电膜. 相关性能测定结果表明, 随着G_8-2-8质量分数的增加, 电导率、 含水率及离子交换量均呈现上升趋势, 特别是在离子交换量和含水率均较低的情况下, OH^-的迁移效率得到明显提升. 经过400 h的耐碱性测试, 结果表明, 该系列膜的电导率降幅仅为1.5%左右, 且外观形貌无明显变化, 表现出优异的耐碱稳定性.     

碱性固体燃料电池碱性聚合物电解质膜的最新研究进展

最近,碱性聚合物电解质膜燃料电池（APEMFC）因具有电极反应动力学快以及不依赖于贵金属铂催化剂等诸多优点而成为一个热门话题. 作为其中一个关键部件,碱性聚合物电解质膜直接影响燃料电池的性能和成本.然而,迄今为止,仍然没有令人满意的碱性电解质膜材料. 为此,大量研究被开展和报道. 本文综述了近三年内文献中关于燃料电池碱性聚合物电解质膜的最新研究进展：包括各种各样的合成策略,构效关系,水管理以及非原位或原位稳定性测试等等. 尤其是一些新的金属离子基阴离子交换膜和冠醚基阴离子交换膜首次被提及和评论.此外,还进一步预测了将来的发展趋势.     

碱性固体燃料电池碱性聚合物电解质膜的最新研究进展

最近,碱性聚合物电解质膜燃料电池（APEMFC）因具有电极反应动力学快以及不依赖于贵金属铂催化剂等诸多优点而成为一个热门话题. 作为其中一个关键部件,碱性聚合物电解质膜直接影响燃料电池的性能和成本.然而,迄今为止,仍然没有令人满意的碱性电解质膜材料. 为此,大量研究被开展和报道. 本文综述了近三年内文献中关于燃料电池碱性聚合物电解质膜的最新研究进展：包括各种各样的合成策略,构效关系,水管理以及非原位或原位稳定性测试等等. 尤其是一些新的金属离子基阴离子交换膜和冠醚基阴离子交换膜首次被提及和评论.此外,还进一步预测了将来的发展趋势.     

Comb-shaped 2-Methylimidazolium Poly(arylene ether sulfone) Anion Exchange Membranes with High Alkaline Stability

A series of comb-shaped poly(arylene ether sulfone)s containing pendant 2-methyl-3-alkylimidazolitun group(ImPAES-Cx,x=1,6,10)was prepared and characterized as novel anion exchange membranes.These Im-PAES-Cx membranes were obtained by benzylic bromination and imidazolium functionalization.The characteristic nano-phase separation structure was formed in membranes with longer alkyl side chains,as confmned by small-angle X-ray scattering.The nano-phase separation structures endowed ImPAES-Cx membranes with improved ionic conductivity,dimensional stability(at least 60% decrease water uptake and swelling ratio at 60℃)and mechanical properties,together with excellent alkaline stability.Especially,ImPAES-C6 membranes possessed enhanced hydroxide conductivity and chemical stability simultaneously.These results suggest that it is a feasible strategy to introduce appropriate length of alkyl side chains into anion exchange membranes(AEMs)to improve the performance.     

碱性固体燃料电池碱性聚合物电解质膜的最新研究进展

最近,碱性聚合物电解质膜燃料电池(APEMFC)因具有电极反应动力学快以及不依赖于贵金属铂催化剂等诸多优点而成为一个热门话题.作为其中一个关键部件,碱性聚合物电解质膜直接影响燃料电池的性能和成本.然而,迄今为止,仍然没有令人满意的碱性电解质膜材料.为此,大量研究被开展和报道.本文综述了近三年内文献中关于燃料电池碱性聚合物电解质膜的最新研究进展:包括各种各样的合成策略,构效关系,水管理以及非原位或原位稳定性测试等等.尤其是一些新的金属离子基阴离子交换膜和冠醚基阴离子交换膜首次被提及和评论.此外,还进一步预测了将来的发展趋势.     

PVA碱性凝胶聚合物电解质薄膜电化学稳定性研究

应用溶解—铸膜法制备聚乙烯醇(polyvinylalcohol,PVA)碱性凝胶聚合物电解质(gelpolymerelectrolyte,GPE)薄膜.交流阻抗(EIS)测试表明,随着KOH含量的增加,该薄膜的离子电导率表现为先增大而后减小的变化趋势,当KOH含量为42%(bymass,下同)时,电导率达到最大值,为2.01×10-3S/cm.X射线衍射(XRD)结果表明,当膜中KOH含量大于20%时,晶态的PVA就逐渐转变为非晶态结构.又当KOH含量增加到一定值后,由于体系中未电离的非晶态KOH量的增多而导致离子电导率下降.循环伏安(CV)和拉曼光谱(Raman)结果表明,该薄膜具有很好的电化学稳定性,可应用于碱性二次电池.     

季铵盐阴离子交换膜研究进展

近年来,阴离子交换膜燃料电池的发展受到了广泛关注。开发具有碱稳定性能优异,电导率高的阴离子交换膜(AEMs)材料成为了研究的热点。AEMs主要由聚合物骨架和阳离子基团组成,这两者是影响膜碱稳定性和电导率的重要因素。本文综述了季铵盐类阴离子交换膜聚合物骨架结构中含有醚氧键和不含醚氧键的烷基季铵盐AEMs、N-螺环季铵盐AEMs和环季铵盐AEMs的碱稳定性、电导率等性能;总结了不同骨架结构季铵盐AEMs碱稳定性的差异;分析了季铵盐的降解机理。同时对于含有季铵盐阳离子交换基团的AEMs的结构设计进行了分析和展望。     

Modification and characterization of semi-crystalline poly(vinyl alcohol) with interpenetrating poly(acrylic acid) by UV radiation method for alkaline solid polymer electrolytes membrane

Semi-crystalline poly(vinyl alcohol) was modified by UV radiation with acrylic acid monomer to get interpenetrating poly(acrylic acid) modified poly(vinyl alcohol), PVAAA, membrane. The stability of various PVAAA membranes in water, 2 M CH₃OH, 2 M H₂SO₄, and 40 wt% KOH aqueous media were evaluated. It was found that the stability of PVAAA membrane is stable in 40 wt% KOH solution. The PVAAA membranes were characterized by differential scanning calorimetry, X-ray diffraction, and thermogravimetry analysis. These results show that (1) the crystallinity in PVAAA decreased with increasing the content of poly(acrylic acid) in the PVAAA membranes. (2) The melting point of the PVAAA membrane is reduced with increasing the content of poly(acrylic acid) in the membrane. (3) Three stages of thermal degradation were found for pure PVA. Compared to pure PVA, the temperature of thermal degradation increased for the PVAAA membrane. The various PVAAA membranes were immersed in KOH solution to form polymer electrolyte membranes, PVAAA-KOH, and their performances for alkaline solid polymer electrolyte were conducted. At room temperature, the ionic conductivity increased from 0.044 to 0.312 S/cm. The result was due to the formation of interpenetrating polymer chain of poly(acrylic acid) in the PVAAA membrane and resulting in the increase of charge carriers in the PVA polymer matrix. Compared to the data reported for different membranes by other studies, our PVAAA membrane are highly ionic conducting alkaline solid polymer electrolytes membranes.     

Synthesis and properties of hydroxide conductive polymers carrying dense aromatic side-chain quaternary ammonium groups

A series of hydroxide conductive polymers QTBMs carryingdense aromatic side-chain quaternary ammonium groups has been synthesized by using a new monomer of 3,3′-di(3′′,5′′-dimethylphenyl)-4,4′-difluorodiphenyl sulfone and other commercial monomers via polycondensation reaction, and subsequent bromination, quaternization and alkalization.The chemical structures of the ionomers were confirmed by ~1H-and ~(13)C-NMR spectroscopy. Water uptake, swelling ratio, hydroxide conductivity, the number of bonded water per ammonium group(λ), volumetric ion exchange capacity(IEC_(Vwet)), mechanical and thermal properties, and chemical stability were systematically evaluated for the series of QTBMs membranes. QTBMs showed IECs ranging from1.02 meq·g~(-1)to 2.11 meq·g~(-1); in particular, QTBM-60 membrane with the highest IEC(2.11 meq·g~(-1)) had very high hydroxide ion conductivity of 131.9 m S·cm~(-1) at 80 °C, which was attributed to the well assembled nano-channels with distinct phase separation evidenced by small-angle X-ray scattering(SAXS). It was found that the hydrated QTBMs membranes were mechanically stable with moderate water uptakes and swelling ratios, high chemical stability under the harsh alkaline conditions. This work provides a facile way to prepare anion exchange membranes(AEMs) with high performances for the application in alkaline fuel cells.     

Preparation of alkaline anion exchange membranes based on functional poly(ether-imide) polymers for potential fuel cell applications

A novel poly(ether-imide)-based alkaline anion exchange membrane with no free base has been prepared and characterized for its ionic conductivity in water, which is a critical metric of its applicability in a liquid-fed direct methanol fuel cell. The poly(ether-imide)-based membranes were prepared by chloromethylation, quaternization and alkalization of commercial poly(ether-imide) and the derivatives were characterized by NMR. The chemical and thermal stabilities were investigated by measuring changes of ionic conductivities when the membranes were placed in various alkaline concentrations and temperatures for 24 h. The membranes were stable at all concentrations of KOH at room temperature, but not at elevated temperatures. The membranes were stable in 1.0 M KOH solution up to 80 °C without losing membrane integrity. The measured conductivity of the formed membrane ranged from 2.28 to 3.51 × 10⁻³ S/cm at room temperature. This preliminary study indicates that functionalized poly(ether-imide) has suitable conductivity suggesting that it can be used as an alkaline anion exchange membrane in fuel cell applications.