高效甲醇水蒸气重整制氢的SBA-15改性的Cu/ZnO/Al2O3催化剂

以介孔SBA-15为结构助剂, 制备出用于甲醇水蒸气重整制氢的新型高效氧化硅掺杂的Cu/ZnO/Al₂O₃催化剂, 并与传统Cu/ZnO/Al₂O₃催化剂在相同条件下的催化性能进行了比较. 结果表明, 添加适量介孔SBA-15可显著提高催化剂的催化活性和选择性, 在大幅度提高甲醇转化率的同时有效降低了重整产气中CO的含量. 原位XRD分析证实适量介孔SBA-15的添加对传统Cu/ZnO/Al₂O₃催化剂的微结构性质可产生重要的调控作用, 从而大大改善其催化活性和制氢选择性.     

高效甲醇水蒸气重整制氢的SBA-15改性的Cu/ZnO/Al2O3催化剂

以介孔SBA-15为结构助剂, 制备出用于甲醇水蒸气重整制氢的新型高效氧化硅掺杂的Cu/ZnO/Al₂O₃催化剂, 并与传统Cu/ZnO/Al₂O₃催化剂在相同条件下的催化性能进行了比较. 结果表明, 添加适量介孔SBA-15可显著提高催化剂的催化活性和选择性, 在大幅度提高甲醇转化率的同时有效降低了重整产气中CO的含量. 原位XRD分析证实适量介孔SBA-15的添加对传统Cu/ZnO/Al₂O₃催化剂的微结构性质可产生重要的调控作用, 从而大大改善其催化活性和制氢选择性.     

Ni基催化剂催化燃油重整耦合选择性催化还原NOx反应

分别以La₂O₂CO₃, CeO₂, ZrO₂和Al₂O₃为载体, 采用浸渍法制备了Ni基重整催化剂, 并以正十二烷模拟车载燃油进行催化重整反应以同时制备小分子碳氢化合物(HCs)和H₂, 考察了其在4wt%Ag/Al₂O₃上选择性催化还原(HC-SCR)氮氧化物(NO_x)的性能. 采用N₂吸附-脱附、X射线粉末衍射、H₂程序升温还原和热重等手段对Ni基催化剂进行了表征. 结果表明, 随着重整催化剂氧化还原性能增强, 产物中H₂浓度增加, 可参与SCR反应的HCs含量减少, 从而导致重整-SCR耦合体系上NO_x净化活性温度窗口向低温移动, NO_x最高转化率降低. Ni/ZrO₂+Ag/Al₂O₃耦合体系中H₂/HCs符合SCR反应所需的最优比例, 在柴油车典型排气温度范围内表现出良好的NO_x净化能力. 同时, 在Ni/ZrO₂+Ag/Al₂O₃耦合体系上考察了其燃油重整-SCR的活性稳定性. 结果显示, 重整催化剂的耐久性有待进一步提高.     

介孔Ni/MgO催化剂催化水蒸气重整生物质油制氢

采用水热法制备了介孔MgO作为催化剂的载体,并制备了介孔Ni/MgO催化剂。利用N_2吸附-脱附、XRD、H_2-TPR等对样品进行表征,并考察了介孔Ni/MgO催化水蒸气重整糠醛、生物质油模型物和两种商用生物质油制氢的活性。结果表明,在介孔Ni/MgO催化剂催化水蒸气重整糠醛制氢反应中,随着反应温度的提高,水蒸气重整糠醛中糠醛的转化率、氢气的产率和氢气的选择性,都呈现递增的趋势。在反应温度提高到600℃时,糠醛的转化率和氢气的产率分别达到94.9%和83.2%。Ni/MgO催化水蒸气重整二组分模拟生物质油,糠醛/乙酸、糠醛/羟基丙酮制氢的反应中,氢气的产率分别达到87.3%和86.8%,均高于水蒸气重整糠醛反应中氢气的产率。由此表明,乙酸或羟基丙酮的存在,提高了模拟生物质油中主要有机物组分糠醛的转化率,并相应地提高了氢气的产率。在水蒸气重整商用生物质油制氢反应中,随着反应物水碳比(S/C(molar ratio)=5、10、15、20、25)的提高,主要有机物的转化率、氢气的产率和选择性呈现出增加的趋势。在水碳比为20时,两种生物质油的主要有机物组分(糠醛、乙酸和羟基丙酮)的转化率均可达90%以上,氢气的产率也达到81.0%以上。由此可知,Ni催化剂对于水蒸气重整商用生物质油也具有较高的催化活性。     

高活性固体碱Na2O/Al2O3-MgO的合成与表征

过量NaOH易引起铝离子流失,造成以Al₂O₃-MgO为载体的催化剂性能不稳定,为此以NH₃为沉淀剂制备了Mg-Al共沉淀物,进而通过Na₂CO₃浸渍、老化、焙烧处置,制备了Na₂O/Al₂O₃-MgO催化剂,借助XRD、SEM、SEM-EDS、TG-DSC、N₂吸附-脱附等手段对其结构及形貌进行表征,以蒜头果油甲酯化率对其活性进行评价,结果表明：采用共沉淀-浸渍的处理方法可以获得类水滑石片层结构的催化剂前驱体,该前驱体主要分解温度在200~500℃之间,经高温煅烧处理后所得催化剂中有Na-Al及Na-Mg-Al氧化物形成。制备高活性Na₂O/Al₂O₃-MgO催化剂的条件为：镁铝离子比n_Mg/n_Al=3∶1~1∶3、老化时间12 h、焙烧温度550℃、焙烧时间5 h。以n_Mg/n_Al=1∶1时制备的催化剂进行验证实验发现,所得催化剂比表面积为30 m²·g^-1、平均孔径为8.8 nm,是一种介孔催化剂,该催化剂在蒜头果油甲酯化实验中表现出高的催化活性,蒜头果油甲酯化率最高达到96.4%。     

预处理方法对Ni-Co双金属催化剂性能与结构的影响

浸渍法制备了Ni-Co/La₂O₃-γ-Al₂O₃双金属催化剂, 经氢气还原预处理后, 再分别由一氧化碳、甲烷和二氧化碳进行再次预处理, 考察了预处理方法对该催化剂上沼气重整制氢性能的影响, 并运用X射线衍射(XRD)、热重-差示扫描量热(TG-DSC)、透射电子显微镜(TEM)等手段对催化剂进行了表征. 结果表明, 与传统氢气还原预处理相比, 经氢气与一氧化碳预处理后, 催化剂性能无明显变化; 经氢气与甲烷预处理后, 催化剂性能明显变差; 而经氢气和二氧化碳预处理后, 催化剂性能明显变优, 且能基本消除该催化剂上沼气重整反应的诱导期. 分析结果表明, 经氢气和二氧化碳预处理后, 催化剂中金属颗粒较小, 分布较均匀, 粒径分布范围较窄, 从而减少了催化剂表面碳的沉积, 增强了催化剂的抗积炭性能, 可延长催化剂的使用寿命.     

ZnFe2O4/CNFs钛网基对电极膜厚对染料敏化太阳能电池性能的影响

通过静电纺丝和简单的一步水热法合成了碳纳米纤维（CNFs）负载的ZnFe₂O₄纳米颗粒（ZnFe₂O₄/CNFs）,并将其刮涂在钛网基底上作为染料敏化太阳能电池（DSSCs）的对电极进行组装测试,电池表现出优异的电化学性能。我们着重研究了不同膜厚对电极对DSSCs光电性能的影响。经过反复测试结果表明,当ZnFe₂O₄/CNFs复合电极材料膜厚为12 μm时存在最高的光电转换效率8.60%。     

La促进水滑石衍生镍基催化剂的原位制备及其CO2甲烷化性能

采用原位生长法制备水滑石衍生Ni-La/Al₂O₃催化剂，并用于CO₂甲烷化反应，以研究La掺杂量对所得催化剂形貌结构及催化性能的影响。利用电感耦合等离子体发射光谱、X射线衍射、氢气程序升温还原、低温氮气吸附-脱附测试、扫描电镜和透射电镜对催化剂的形貌结构进行分析。结果表明，适宜的La掺杂量能够提高活性金属Ni在载体中的分散性，减弱Ni与载体的相互作用，并且改善催化剂的孔隙结构，提高催化剂的比表面积。CO₂甲烷化性能表明，当Ni负载量(质量分数)为30%、La掺杂量(质量分数)为10%时，催化剂30Ni-10La/Al₂O₃具有较优的催化性能； 350℃时其CO₂转化率及CH₄产率分别达到91.9%和91.5%，并且连续测试60 h后催化性能基本保持不变。     

Pt/Ce0.6Zr0.4O2催化剂催化氧化碳烟过程中活性氧对NO-NO2循环及表面含氧物种的分解作用简

通过在Ce_0.6Zr_0.4O₂载体上浸渍Pt（NO₃）₂制得Pt/Ce_0.6Zr_0.4O₂催化剂,该催化剂在松散接触条件下,于NO+O₂或O₂气氛中均表现出比Pt/Al₂O₃更好的碳烟氧化性能. 进一步研究表明,Pt/Ce_0.6Zr_0.4O₂催化剂中的Pt 与Ce_0.6Zr_0.4O₂存在相互作用,使得催化剂在一定温度范围内对活性氧的利用率大为提高,从而促进了气氛中NO↔NO₂的循环,乃至碳烟与NO₂的反应和碳烟表面含氧中间物种的生成;更重要的是,这部分活性氧本身可加速含氧中间物种的分解. 因此,在NO + O₂的气氛中,Pt/Ce_0.6Zr_0.4O₂催化剂的碳烟起燃温度比Pt/Al₂O₃降低了34 ℃.     

低负载量的双金属Au@Pt核壳催化剂催化氧化甲苯

采用液相氢气两步还原法制备了双金属Au@Pt核壳纳米粒子,通过直接吸附法将纳米粒子均匀地分散于载体上,制备出低负载量的双金属Au@Pt/Al₂O₃催化剂,并且评价了催化剂对甲苯的催化氧化性能。通过TEM、XRD、XPS、N₂吸附-脱附和H₂-TPR等对催化剂进行了表征。结果表明,与单金属Au和Pt催化剂相比,双金属Au@Pt核壳催化剂表现出更高的催化活性,具有很好的稳定性和选择性,在甲苯体积分数为1×10^-3,气体空速为18 L·g^-1·h^-1的条件下,Au₁@Pt₂/Al₂O₃核壳催化剂具有优异的催化氧化性能,其中甲苯实现98%的转化率的温度（T₉₈）为195℃。由XPS结果可知,在Au和Pt之间存在电子转移促进了Pt上活性氧物种的形成,催化剂的活性组分主要以Au⁰和Pt⁰的形式存在,并广泛分布在载体的表面上。Au@Pt纳米粒子与载体Al₂O₃之间的强相互作用也是提高甲苯催化氧化活性的重要因素。     

在Ni/HZSM-5催化剂上低温水蒸汽重整生物油制氢

We investigated high catalytic activity of Ni/HZSM-5 catalysts synthesized by the impregna-tion method, which was successfully applied for low-temperature steam reforming of bio-oil. The influences of the catalyst composition, reforming temperature and the molar ratio of steam to carbon fed on the stream reforming process of bio-oil over the Ni/HZSM-5 catalysts were investigated in the reforming reactor. The promoting effects of current passing through the catalyst on the bio-oil reforming were also studied using the electrochemical catalytic re-forming approach. By comparing Ni/HZSM-5 with commonly used Ni/Al₂O₃ catalysts, the Ni₂₀/ZSM catalyst with Ni-loading content of about 20% on the HZSM-5 support showed the highest catalytic activity. Even at 450 oC, the hydrogen yield of about 90% with a near complete conversion of bio-oil was obtained using the Ni₂₀/ZSM catalyst. It was found that the performance of the bio-oil reforming was remarkably enhanced by the HZSM-5 supporter and the current through the catalyst. The features of the Ni/HZSM-5 catalysts were also investigated via X-ray diffraction, inductively coupled plasma and atomic emission spectroscopy, hydrogen temperature-programmed reduction, and Brunauer-Emmett-Teller methods.     

Ni/Al2O3改性催化剂催化重整生物油模拟物制氢研究

制备了Ni/Al₂O₃、Ni-Cu/Al₂O₃、Ni-Co/Al₂O₃和Ni-Co-Cu/Al₂O₃催化剂,研究了Co和Cu对生物油水蒸气催化重整的影响。实验表明,Co 能促进水汽变换(WGS)反应,提高氢气的产率,Cu能抑制反应中焦炭的形成,提高催化剂的稳定性。对催化剂Ni-Co-Cu/Al₂O₃进行工艺条件考察,当900 ℃、水油比为6 g/g、质量空速(WHSV)为1 h^-1时,碳选择性达到87.5%,氢气产率达到84.2%,潜在氢气产率达到92.4%。     

Effects of Preparation Method on the Performance of Ni/Al2O3 Catalysts for Hydrogen Production by Bio-Oil Steam Reforming

Steam reforming of bio-oil derived from the fast pyrolysis of biomass is an economic and renewable process for hydrogen production. The main objective of the present work has been to investigate the effects of the preparation method of Ni/Al₂O₃ catalysts on their performance in hydrogen production by bio-oil steam reforming. The Ni/Al₂O₃ catalysts were prepared by impregnation, co-precipitation, and sol?Cgel methods. XRD, XPS, H₂-TPR, SEM, TEM, TG, and N₂ physisorption measurements were performed to characterize the texture and structure of the catalysts obtained after calcination and after their subsequent use. Ethanol and bio-oil model compound were selected for steam reforming to evaluate the catalyst performance. The catalyst prepared by the co-precipitation method was found to display better performance than the other two. Under the optimized reaction conditions, an ethanol conversion of 99% and a H₂ yield of 88% were obtained.     

Hydrogen Production by Catalytic Reforming of Liquid Hydrocarbons

In this review, we are reporting the catalytic reforming of liquid hydrocarbon fuels carried out in our research group, covering the catalytic reforming of iso-octane and toluene as surrogate of gasoline, gasoline fuel processor system and steam reforming of n-hexadecane and decahydronaphthalene, main constituents of diesel. The commercial ICI reforming catalyst is prone to be poisoned by sulfur contained in iso-octane. We investigated various supported transition metal formulations and developed Ni/Fe/MgO/Al₂O₃ (KIST-5) catalyst with prolonged catalytic stability (>760 h), higher activity and sulfur tolerance ability over commercial ICI and HT catalysts for ATR reaction of iso-octane. We found that the concentration of CO can be reduced to <1,800 ppm by the gasoline fuel processor system charged with KIST-5 reforming catalyst, commercial HTS catalyst and KIST Pt–Ni/CeO₂ LTS catalyst. The addition of Rh metal to spc-Ni/MgAl catalyst as promoter was found to be very effective in inhibiting the deactivation of spc-Ni/MgAl catalyst by sintering of reduced Ni metal at high temperature during steam reforming of n-hexadecane. A 0.3 wt% Rh loading on spc-Ni/MgAl catalyst was optimized to have the best performance for steam reforming of n-hexadecane among the prepared catalysts. The addition of Rh to spc-Ni/MgAl catalyst also restricted the deactivation of the catalyst due to carbon formation at high reaction temperature. In view point of prolonged stability and higher activity, these developed reforming catalysts have a good scope in the reforming process of gasoline and diesel for hydrogen station and fuel processor system applications.     

Catalytic steam reforming of model compounds of biomass pyrolysis liquids in fluidized bed reactor with modified Ni/Al catalysts

Catalytic steam reforming of acetic acid and hydroxyacetone (acetol) as model compounds of the aqueous fraction of bio-oil (biomass derived pyrolysis liquids) was studied in fluidized bed reactor over Ni/Al catalysts modified with calcium or magnesium. Attrition tests showed that the use of small quantities of these promoters improved the mechanical strength of the reforming catalyst. An optimum Ca/Al molar ratio of 0.12 and a Mg/Al molar ratio of 0.26 leaded to attrition rates of 0.22 and 0.27 wt%/h, respectively. Steam reforming experiments were performed at 650 °C and a steam to carbon molar ratio (S/C) of 5.58. The promoted catalysts showed different acetic acid steam reforming activities depending on the Ca/Al or Mg/Al molar ratios. Magnesium modified catalysts with a Mg/Al molar ratios of 0.26 and 0.50 showed good performances with almost no activity loss with time in contrast to the calcium modified catalysts that showed higher CO and CH₄ yields. The addition of calcium generated a NiO phase with less interaction with the support. The highest H₂ yield and carbon conversion in acetic steam reforming were obtained by a magnesium promoted catalyst with a Mg/Al ratio of 0.26, while the nonpromoted Ni/Al catalyst showed the best performance in acetol steam reforming. Then, the nature of the organic compound influenced the performance of the different catalysts.     

镍基催化剂上乙醇水蒸气重整反应的研究

考察了载体对Ni催化剂乙醇水蒸气重整制氢反应性能的影响。结果表明，Ni/CeO2催化剂具有较好的低温活性和氢气选择性。对Ni担载量和焙烧温度考察发现，400℃焙烧的15%NiCeO2催化剂具有较好的催化性能；继续升高焙烧温度引起NiO和CeO2粒子的显著增大,导致对氢气选择性的降低。较小的Ni和CeO2粒子有利于乙醇水汽重整反应的进行，而大的粒子倾向于乙醇的分解反应。 350℃时,在反应过程中分别添加CO、CO2和CH4的结果表明没有发生CO和CO2甲烷化反应,而发生了一定程度的CH4水汽重整反应。     

生物油水溶性组分的水蒸气催化重整制氢实验研究

利用固定床反应器对生物油水溶性组分重整制氢反应进行了考察,研究了温度、吸收剂的加入对反应过程的影响。结果表明,在常压条件下生物油水溶性组分的最佳重整温度为800℃,此时H2体积分数为60%、CO体积分数为10%。加入CO₂吸收剂后,H₂体积分数提高了25%,H₂产率提高了10%。在常压条件下,以CaO作为吸收剂时,最佳的反应温度为600℃,此时H₂体积分数最高可达85%。650℃时CaO对CO₂的吸收能力减弱导致其对生成H₂反应的促进作用急剧降低。     

Maximum Hydrogen Production by Autothermal Steam Reforming of Bio-oil With NiCuZnAl Catalyst

Autothermal steam reforming (ATR) of bio-oil, which couples the endothermic steam reform-ing reaction with the exothermic partial oxidation, offers many advantages from a technical and economic point of view. Effective production of hydrogen through ATR of bio-oil was performed at lower temperature with NiCuZnAl catalyst. The highest hydrogen yield from bio-oil reached 64.3% with a nearly complete bio-oil conversion at 600 oC, the ratio of steam to carbon fed (S/C) of 3 and the oxygen to carbon ratio (O/C) of 0.34. The reaction con-ditions in ATR including temperature, O/C, S/C and weight hourly space velocity can be used to control both hydrogen yield and products distribution. The comparison between the ATR and common steam reforming of bio-oil was studied. The mechanism of the ATR of bio-oil was also discussed.     

Ni/ZrO2催化剂上甲烷水蒸气重整反应的研究

研究了Ni/ZrO2催化剂对甲烷水蒸气重整制合成气的反应性能。考察了催化剂的还原温度、载体焙烧温度以及反应温度、原料配比和空速等对催化剂性能的影响。利用XRD、TEM、XPS等手段对催化剂的织构形貌进行了表征。研究表明，Ni/ZrO2催化剂用于甲烷水蒸气重整制合成气不仅具有较高的活性，也具有较好的稳定性。水蒸气比增加，CH4转化率增大、CO选择性下降。CH4转化率及CO选择性均随空速增大而下降。使用10%Ni/ZrO2催化剂，在650 ℃、空速1.984×104 h－1、原料气配比H2O∶CH4∶N2=2∶1∶2.67的条件下，获得CH4转化率85%、CO选择性70%的结果。     

Effect of ceria loading on the carbon formation during low temperature methane steam reforming over a Ni/CeO2/ZrO2 catalyst

The characterization and catalytic activity of a Ni/CeO₂/ZrO₂ catalyst for methane steam reforming at 600°C were investigated. The addition of ceria increased the surface area and basicity of the catalysts. The redox reaction capability of the ceria increased the hydrogen yield and carbon monoxide selectivity, and inhibited carbon formation.