纳米金/3-氨丙基-三乙氧基硅烷修饰传感器电化学检测NO-2

将3-氨丙基-三乙氧基硅烷（ATS）修饰在玻碳电极表面,再自组装一层纳米金,制备了一种新型NO2^-的电化学传感器。该修饰电极对NO2^-有较好的催化作用。在pH为3时,NO2^-的氧化峰电流与其浓度在5．0×10^-7～1．0×10^-3mol／L范围内呈良好的线性关系,检出限可达2．0×10^-7mol／L。方法具有较高的灵敏度和较好的重现性。     

诺必擂停的电化学性质研究及示差脉冲伏安法测定

研究了抗癌药物诺必擂停在玻碳电极上的电化学行为及其反应机理,建立了一种灵敏的测定诺必擂停的分析方法。实验结果表明,在pH 2.0的磷酸盐缓冲溶液中,诺必擂停在-0.905 V电位处产生灵敏的还原峰,该还原峰电流与诺必擂停的浓度在8.21×10^-6-1.09×10^-4mol/L范围内呈现良好的线性关系（r=0.9923）,检出限为5.47×10^-6mol/L。该法已用于人血清中诺必擂停的测定,回收率在94.5%-104.4%之间。     

布美他尼在玻碳电极上伏安行为的研究

用微分脉冲伏安（DPV）法研究了利尿剂类药物布美他尼在玻碳电极上的电化学行为。在pH2.87的B-R缓冲液中,布美他尼在＋0.896V（vs.SCE）电位处产生一个阳极氧化峰,其峰电流与布美他尼的浓度在6.0×10^-8—2.5×10^-5mol／L的范围内呈良好的线性关系,检出限（3σ／K）为2.4×10^-8mol／L。将该法应用于布美他尼实际药片及模拟尿样的测定,结果令人满意。初步探讨了布美他尼的电化学机理。     

电化学法研究橙黄Ⅳ和溶菌酶的相互作用

在pH 11.00的NH3-NH4Cl缓冲溶液中,橙黄Ⅳ与溶菌酶能形成一种橙黄色的超分子复合物。用线性扫描二阶导数极谱法对该体系进行了研究,复合物的形成使橙黄Ⅳ的还原峰电位不变,峰电流下降,并且该峰电流的下降值同所加的溶菌酶的浓度在一定范围内呈线性关系。用于溶菌酶的测定,在1.6×10^-9-1.0×10^-8mol/L,1.0×10^-8-8.0×10^-8mol/L,9.0×10^-8-1.6×10^-7mol/L三段范围内呈线性关系,检出限为4.0×10^-10mol/L,进而对模拟样品进行分析,并对结合反应机理进行初步的探讨。     

基于纳米MnO2的免标记型DNA电化学生物传感器用于大肠杆菌的测定

以室温固相合成法制备纳米MnO2,通过壳聚糖（CHIT）的成膜效应将纳米MnO2固定在玻碳电极表面。DNA在MnO2/CHIT膜上的固定和杂交通过循环伏安和电化学交流阻抗进行表征。以电化学阻抗免标记法检测目标DNA,固定于电极表面的DNA探针与目标DNA杂交后使电极表面的电子传递电阻增大,以此作为检测信号可以高灵敏度地测定目标DNA。电化学阻抗谱检测大肠杆菌基因片段的线性范围为2.0×10^-11 ～2.0×10^-6mol/L,检出限为1.0×10^-12mol/L。     

5-HIAA在MWNT-Nation修饰电极上的伏安行为

研究了在磷酸盐缓冲溶液（pH7．0）中，5-羟基吲哚乙酸（5-HIAA）在MWNT-Nafion修饰电极上的电化学行为。5-HIAA在MWNT-Nafion修饰电极上出现一个灵敏的氧化峰。与裸玻碳电极相比，MWNT—Nation修饰电极提高5-HIAA的氧化峰电流。优化了各项测定参数，建立了一种直接测定HIAA的电分析方法。富集电位为-0．5V，富集时间为300s，氧化峰电流与5-HIAA的浓度在9．95×10^-5～7．98×10^-3mol／L之间有良好的线性关系。检出限为2．5×10^-6 mol／L。     

米托蒽醌分子印迹聚邻氨基酚敏感膜传感器的研制

在弱酸性条件下,在金电极上以邻氨基酚为单体和交联剂,米托蒽醌为模板分子,用循环伏安法电聚合成米托蒽醌分子印迹聚邻氨基酚敏感膜传感器。该传感器对米托蒽醌具有良好的选择性和敏感度,米托蒽醌浓度分别在2.0×10^-7—1.0×10^-5mol／L及1.0×10^-5—5.0×10^-5mol／L范围内与峰电流减小量呈线性关系,检出限为1.2×10^-7mol／L。本文同时对分子印迹膜的结构和性能进行了探讨与研究。     

一种基于碳纳米管的色氨酸传感器

研究了色氨酸(tryptophan即Trp)在多壁碳纳米管修饰玻碳电极(MWNTs/GC)上的电化学行为。MWNTs/GC电极对Trp具有良好的电催化作用,相对于GC电极,Trp在MWNTs/GC上峰电位负移128 mV,峰电流约为GC电极上氧化峰电流的31倍。在1.0 mol/L H2SO4中清洗能更新电极表面,消除产物吸附带来的影响。MWNTs/GC电极在含1.0×10-4mol/L Trp的缓冲溶液中闭路富集2 min时电流达到稳定值。研究了不同pH值影响的结果表明,参与电极反应的质子数和电子数相等。在pH=2.2时,Trp的氧化电流最大。利用LSV研究了电流与扫描速率的关系,结果表明,Trp在修饰电极上的氧化过程为扩散控制过程。在环境温度低于45℃时,随着温度增加,氧化电流逐渐增大。温度在16~35℃范围内,传感器的响应电流与温度成线性关系,温度系数为0.695μA/℃,说明此传感器在实测过程中因温度波动带来的测量误差很小。利用LSV研究了氧化峰电流与Trp的浓度关系的结果显示,峰电流与Trp的浓度在1.00×10-6~1.00×10-4mol/L范围内呈良好线性关系,检出限为1.82×10-7mol/L(S/N=3)。该电极具有良好的灵敏度、选择性和稳定性,放置7 d后,碳纳米管的峰电流仍能达到最初电流的98%。     

酸性大红3R的电化学研究及应用

采用循环伏安法和方波伏安法考察了酸性大红3R在碳糊电极上的伏安行为和反应机理。当扫描速率为0.1 V/s时,在pH 1的0.05 mol/L H2SO4支持电解液中,酸性大红3R有一对峰电位分别是0.74 V和0.72 V（vs.饱和甘汞电极）的氧化峰和还原峰,并且显示吸附控制的2电子单质子的准可逆氧化还原过程。在最佳实验条件下,酸性大红3R的方波氧化峰峰电流与其浓度在2.12×10^-5-3.39×10^-4mol/L范围内呈线性关系,检出限为8.35×10^-6mol/L,由此建立测定酸性大红3R含量的方波伏安法。该方法可用于计算酸性大红3R常规染羊毛与蚕丝的上染率,测定结果与分光光度法一致。     

己硫醇二茂铁复合金纳米粒子修饰电极对多巴胺的催化性能研究

将自行合成的己硫醇二茂铁自组装于金纳米粒子表面,获得己硫醇二茂铁复合金纳米粒子（Au@S（CH2）6Fc）。采用滴涂法将制备的复合纳米粒子固定于玻碳电极表面,制备Au@S（CH2）6Fc修饰电极,采用循环伏安法对修饰电极的电化学性能进行考察。将制备的修饰电极用于对神经递质多巴胺（DA）的催化氧化性能研究。结果表明,该修饰电极对DA具有显著的催化氧化作用,线性范围为1.0×10^-6-2.6×10^-3mol/L,检出限为3.0×10^-7mol/L。     

pMB/MWNTs/GC电极对水体中苯二酚异构体的同时测定

通过在多壁碳纳米管修饰玻碳电极上电聚合亚甲基蓝,制备了聚亚甲基蓝/碳纳米管/玻碳电极(pMB/MWNTs/GC)。用循环伏安法研究了3种苯二酚异构体在该电极上的电化学行为,结果表明,在pH7.0的磷酸盐缓冲溶液中,该修饰电极对苯二酚异构体的氧化表现出优异的电催化性能和选择性,对苯二酚、邻苯二酚和间苯二酚的氧化峰分别为0.104、0.203、0.609 V(vs.SCE),峰电位差值分别为99、406 mV。基于苯二酚异构体在pMB/MWNTs/GC修饰电极上的伏安行为,建立了苯二酚3种异构体同时分析的新方法。考察了各影响因素对测定的影响,最优实验条件下,在5.0×10-6~1.5×10-4mol.L-1范围内,3种苯二酚异构体的阳极峰电流与其浓度存在线性关系,检出限均为1.0×10-6mol.L-1。将该法用于水体及冲洗废液中苯二酚异构体含量的测定,结果满意。     

Multi-walled carbon nanotubes modified glass carbon electrode and its electrocatalytic activity towards oxidation of paracetamol

Multi-walled carbon nanotubes (MWNTs) modified glassy carbon electrode (GCE) was simply and conveniently fabricated. The electrochemical properties of paracetamol (PCT) at the prepared modified electrode were investigated by cyclic voltammetry (CV). Based on this, an ultrasensitive and rapid electrochemical method was developed for the determination of PCT. The result indicated that the oxidation of PCT was greatly improved at the MWNTs-modified GC (MWNTs/GC) electrode as compared with the bare GC electrode, with relatively high sensitivity, stability and life time. Good linear relationship between the oxidation peak current and the PCT concentration in the range of 1 × 10⁻⁷ to 1 × 10⁻³ M (r = 0.996) was obtained in phosphate buffer solution (PBS) with pH 6.5, the detection limit was 2 × 10⁻⁸ M (S/N = 3) by use of modified electrode. The proposed method was successfully applied to the PCT determination in tablets.     

多巴胺和抗坏血酸在十六烷基三甲基溴化铵/碳纳米管电极上的检测

研究了十六烷基三甲基溴化铵(CTMAB)/多壁碳纳米管修饰玻碳电极的制备以及多巴胺和抗坏血酸在该修饰电极上的电化学行为。在CTMAB和多壁碳纳米管的协同作用下,该修饰电极对多巴胺和抗坏血酸均具有显著的催化氧化作用,多巴胺和抗坏血酸的氧化峰电位分别为223mV和15mV,实现了在抗坏血酸共存时测定多巴胺。在pH7.0的磷酸盐缓冲溶液中,多巴胺和抗坏血酸的线性范围分别为2.0×10-6～2.0×10-3mol/L和4.0×10-5～1.0×10-2mol/L,检出限分别为6.0×10-7mol/L和1.0×10-5mol/L。     

Electrocatalytic oxidation of NADH by rutin in biomembrane-like films on glassy carbon electrode

Stable lipid film was made by casting dipalmitoylphosphatidylcholine (DPPC) and rutin onto the surface of a glassy carbon (GC) electrode. The electrochemical behavior of rutin in the DPPC film was studied. The modified electrode coated with rutin gave quasi-reversible reduction-oxidation peak on cyclic voltammogram in the phosphate buffer (pH 7.4). The peak current did not decrease apparently after stored at 4°C for 8 hours in refrigerator. This model of biological membrane was used to investigate the oxidation of dihydronicotinamide adenine dinucleotide (NADH) by rutin. Rutin in the film acts as a mediator. The modified electrode shows a great enhancement and the anodic peak potential was reduced by about 220 mV in the oxidation of 5×10⁻³ mol L⁻¹ NADH compared with that obtained at a bare glassy carbon electrode.     

Sensitive voltammetric determination of tyrosine using multi-walled carbon nanotubes/4-aminobenzeresulfonic acid film-coated glassy carbon electrode

A chemically modified electrode is constructed based on the multi-walled carbon nanotubes (MWNTs)/4-aminobenzeresulfonic acid (4-ABSA) film-coated glassy carbon electrode. The electrocatalytic oxidation of tyrosine (Tyr) is investigated on the surface of the MWNTs/4-ABSA-modified electrode using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The prepared modified electrode shows voltammetric responses with high sensitivity and selectivity for Tyr in optimal conditions, which makes it very suitable for sub-micromolar detection of Tyr. A sensitive oxidation peak at +0.64 V is employed to determine Tyr. Good linear relationship between the oxidation peak current and the Tyr concentration in the range of 1 × 10⁻⁷ to 5 × 10⁻⁵ mol/L is obtained in phosphate buffer solution with pH 7.0. By use of modified electrode, the voltammetric detection limit for Tyr in DPV measurements is 8 × 10⁻⁸ mol/L (S/N = 3). Good sensitivity, selectivity and stability of the low-cost modified electrode make it very suitable for the determination of trace amounts of Tyr in pharmaceutical and clinical preparations.     

Low-potential nicotinamide adenine dinucleotide detection at a glassy carbon electrode modified with toluidine blue O functionalized multiwall carbon nanotubes.

The toluidine blue O (TBO) functionalized multiwall carbon nanotubes (MWNTs) nanomaterials (TBO-MWNTs) were prepared by assembling TBO onto the surface of a MWNTs modified glassy carbon (GC) electrode. Also TBO-MWNTs modified GC electrodes exhibiting a strong and stable electrocatalytic response toward beta-nicotinamide adenine dinucleotide (NADH) were described. Compared with a bare GC electrode, the TBO-MWNTs modified GC electrodes could decrease the oxidization overpotential of NADH by 730 mV, with a peak current at 0.0 V, since there was a positively synergistic electrocatalytic effect between the MWNTs and TBO toward NADH. Furthermore, the TBO-MWNTs modified GC electrodes had perfect performances, such as a low detection limit (down to 0.5 microM), being very stable (the current diminutions is lower than 6% in a period over 35 min), a fast response (within 3 s), and a wide linear range (from 2.0 microM to 3.5 mM). Such an ability of TBO-MWNTs to promote the NADH electron-transfer reaction suggests great promise for dehydrogenase-based amperometric biosensors.     

NAD+在多壁碳纳米管修饰电极上电化学催化还原的研究

The cyclic voltammetric (CV) behaviors of NAD^ were studied with a multi-walled carbon nanotubes (MWNTs) modified glassy carbon (GC) electrode. In 0.05 mol/L tris(hydroxymethyl)aminomethane-HCl (Tris-HCl) buffer solution (pH=6.9), the MWNTs modified electrode showed high electrocatalytic activity toward reduction of NAD^ .The electroreduction of NAD^ was an irreversible diffusion controlled process. The cathodic peak current increased linearly with increasing the concentration of NAD^ . The influences of scan rate, temperature and concentration were also investigated.     

Voltammetric Determination of Uric Acid with a Glassy Carbon Electrode Coated by Paste of Multiwalled Carbon Nanotubes and Ionic Liquid

The voltammetric behavior of uric acid (UA) has been studied at a multiwalled carbon nanotube‐ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium hexafluorophosphate, BMIMPF₆) paste coated glassy carbon electrode (MWNTs‐BMIMPF₆/GC). It is found that UA can effectively accumulate at this electrode and cause a sensitive anodic peak at about 0.49 V (vs. SCE) in pH 4.0 phosphate buffer solutions. Experimental parameters influencing the response of the electrode, such as solution pH and accumulation time, are optimized for uric acid determination. Under the optimum conditions, the anodic peak current is linear to UA concentration in the range of 1.0×10^?8 M to 1.0×10^?6 M and 2.0×10^?6 M to 2.0×10^?5 M. The detection limit is 5.0×10^?9 M for 180 s accumulation on open circuit. The electrode can be regenerated by successively cycling in a blank solution for about 3 min and exhibits good reproducibility. A 1.0×10^?6 M UA solution is measured for eight times using the same electrode regenerated after every determination, and the relative standard deviation (RSD) of the peak current is 3.2%. As for different electrodes fabricated by the same way the RSD (i.e., the electrode to electrode deviation) is 4.2%(n=9). This method has been applied to the determination of UA in human urine samples, and the recoveries are 99%–100.6%. In addition, comparison is made between MWNTs‐BMIMPF₆/GC and MWNTs/GC. Results show that the MWNTs‐BMIMPF₆/GC exhibits higher sensitivity, selectivity and ratio of peak current to background current.     

Electrochemical determination of nitrite using a gold nanoparticles-modified glassy carbon electrode prepared by the seed-mediated growth technique.

Seed-mediated growth of gold nanoparticles on glassy carbon (GC) surfaces was developed. The field emission scanning electron microscopy (FE-SEM) and electrochemical characterization confirmed the effective attachment of gold nanoparticles on GC surface with such a wet-chemical method. The as-prepared gold nanoparticles attached glassy carbon electrode (Au/GCE) presented excellent catalytic ability toward the oxidation of nitrite. Compared with bare GCE and planar gold electrode, the Au/GCE obviously decreased the overpotential of nitrite oxidation and improved the peak current. The catalytic current was found to be linearly proportional to the nitrite concentration in the range of 1 x 10(-5) - 5 x 10(-3) M, with a detection limit of 2.4 x 10(-6) M. The Au/GCE was successfully applied to the electrochemical determination of nitrite in a real wastewater sample, showing excellent stability and anti-interference ability.     

吲哚美辛在单壁碳纳米管修饰电极上的电化学行为

运用伏安法研究了吲哚美辛在单壁碳纳米管修饰电极上的电化学行为.在0.1 mol/L HAc-NaAc缓冲溶液(pH 4.5)中,吲哚美辛于0.91 V (vs.SCE)电位处有一个峰形很好的氧化峰.与裸玻碳电极相比,吲哚美辛在修饰电极上的电位正移了约30 mV,峰电流增加了近10倍,表明该修饰电极对吲哚美辛有较强的电催化作用.搅拌条件下开路富集2 min,氧化峰电流与吲哚美辛在5.5×10-7～1.1×10-5 mol/L浓度范围内呈良好的线性关系,检出限为1.1×10-7 mol/L.该方法可用于药剂中吲哚美辛的分析.