新型锂离子电池CaSnO3负极材料的湿化学制备与电化学性能

采用湿化学方法合成了具有钙钛矿结构的CaSnO₃，将其作为锂离子电池的负极活性物质，研究了其电化学性能。结果表明，湿化学方法制备的锡酸钙，粒度分布集中、平均粒径在500 nm左右，在0～1.0 V之间以0.1 C倍率充放电时，其可逆容量达到469 mAh·g^-1，而且循环性能良好。经80次循环后的容量衰减率只有0.57%。从首次放电容量和可逆容量来看，锡酸钙的储锂机制与锡基氧化物材料相似，即:首先是结构的还原并形成金属锡；然后金属锡与锂发生可逆的合金化与去合金化过程。锡酸钙的可逆容量、循环性能都比文献报道的块状锡氧化物或者是无定型锡基复合氧化物好，这说明钙钛矿结构和钙离子的存在可能对改善锡基负极材料的性能是有益的。     

新型锂离子电池CaSnO_3负极材料的湿化学制备与电化学性能

采用湿化学方法合成了具有钙钛矿结构的CaSnO3,将其作为锂离子电池的负极活性物质,研究了其电化学性能。结果表明,湿化学方法制备的锡酸钙,粒度分布集中、平均粒径在500nm左右,在0￣1.0V之间以0.1C倍率充放电时,其可逆容量达到469mAh·g-1,而且循环性能良好。经80次循环后的容量衰减率只有0.57%。从首次放电容量和可逆容量来看,锡酸钙的储锂机制与锡基氧化物材料相似,即:首先是结构的还原并形成金属锡;然后金属锡与锂发生可逆的合金化与去合金化过程。锡酸钙的可逆容量、循环性能都比文献报道的块状锡氧化物或者是无定型锡基复合氧化物好,这说明钙钛矿结构和钙离子的存在可能对改善锡基负极材料的性能是有益的。     

锂离子电池锡基复合氧化物负极材料的研究

采用共沉淀法制备了SnSbO2.5和SnGeO3两种锡基复合氧化物粉末.XRD分析表明,这两种锡基复合氧化物的共同特点是在27°～28°处有波峰,属无定型结构.将其分别作为锂离子电池负极材料的活性物质,利用恒电流电池测试仪研究它们的电化学性能.实验表明,这两种锡基复合氧化物都有较高的电化学容量,SnSbO2.5的可逆容量为1200mA·h/g,SnGeO3的可逆容量为750mA·h/g.这两种锡基复合氧化物的电化学容量远高于碳材料(石墨的理论容量为372mA·h/g),因此,这两种锡基复合氧化物可以作为锂离子电池负极材料的候选材料.     

微乳液法合成LiFePO4 / C正极材料及其电化学性能

本文采用微乳液方法合成了纳米LiFePO₄ / C正极材料。制备样品分别用XRD和SEM进行表征，充放电测试其电化学性能。600 ℃制备样品为单一物相，平均粒径90 nm，在室温2.0～4.0 V (vs Li) 放电电压范围和15 mA·g^-1放电速率下，首次放电容量达到159 mAh·g^-1。制备样品同样展现良好的循环性能。在15 mA·g^-1速率下40次循环后，制备样品放电容量仍保持首次放电容量的98.9%。优异的电化学性能得益于样品颗粒的纳米尺寸、均匀分布以及表面碳层包覆提高了活性材料的电子电导率。     

锂离子蓄电池正极材料LiMn2-x-y-zTlxAlyMzO4(M=Co、Cr、Ni)的合成及电化学性能研究

采用同时掺杂Tl、Al和M(M=Co、Cr和Ni)三种金属原子和改进固相反应的方法合成了复合尖晶石正极材料 LiMn_2-x-y-zTl_xAl_yM_zO₄，并采用XRD、SEM、TEM、循环伏安和电化学测试考察了它的物理性质和电化学性能。结果表明，所合成的正极材料具有与母体LiMn₂O₄尖晶石同样完整的尖晶石结构，规则的形貌和均匀的粒径分布。当M为Co和Cr时，目标材料的平均粒径约800nm，且具有良好的电化学性能，其首次充电容量分别为123.70mAh·g^-1和121.30mAh·g^-1，首次放电容量分别为117.30mAh·g^-1和115.70mAh·g^-1。当M为Ni时，材料的电化学性能相对较差。循环伏安和充放电曲线表明该正极材料的充放电分别为两步脱锂和插锂机理。当Li掺杂量较小时，目标材料在充放电过程中均各有两个平台。随着Li掺杂量的增加，充放电平台有由两个逐渐转变为一个的趋势。当M为Co或Cr时，该正极材料不仅拥有较高的比容量和常温循环稳定性能，而且还具有较优良的高温循环稳定性能，这可能主要归因于三种金属的协同作用使目标材料的结构更加稳定，这也使该材料有可能成为电动车电池的较佳正极材料。     

新合成方法制备的LiCoO2正极材料的结构和电化学性能研究

采用新合成方法制备了锂离子二次电池正极材料LiCoO₂。通过ICP-AES、XRD、SEM、电化学方法等测试分析了所合成材料的物理性质和电化学性能，并与商品LiCoO₂材料作了对比研究。同时分别以国产MCMB和石墨作负极活性物质、合成的LiCoO₂作正极活性物质做成锂离子电池，对其电化学性能进行了测试。实验结果表明，所合成的LiCoO₂材料的电化学性能优于其它两种商品LiCoO₂材料，其初始放电容量为155.0 mAh·g^-1，50次循环后的容量保持率达95.3%，而且以此为正极的锂离子电池也表现出优良的电化学性能。计时电位分析结果还表明，合成的材料在充放电循环过程中发生了三次相转变过程，但相变过程具有良好的可逆性。     

锰源对尖晶石LiMn2O4高温性能的影响

为考察不同锰源对所制备尖晶石LiMn₂O₄(LMO)电化学性能的影响(特别是高温性能),采用沉淀法制备前驱体,通过不同煅烧温度制备得到最常用的锰氧化物(MnO₂、Mn₂O₃和Mn₃O₄)为锰源,经相同条件制备得到LMO正极材料,通过考察所得LMO形貌及电化学性能来研究锰源与LMO电化学性能的关系。研究结果表明,相同的前驱体在不同煅烧温度下可以得到不同的锰氧化物,且各自具有不同的形貌结构。由这些锰氧化物都可以得到高纯度的LMO,但产物形貌结构以及材料中的八面体晶体含量和尺寸不同。由Mn₂O₃制备得到的LMO材料中的八面体晶体含量最多,且尺寸最均匀,在3种LMO中容量性能、倍率性能和循环性能最好：0.2C(1C=148 mA·g^-1)下首次放电比容量为131.8 mAh·g^-1;3C下还有100.4 mAh·g^-1的放电比容量。其对应半电池在0.5C下循环100次后,放电比容量还有116.0 mAh·g^-1,容量保持率为93.9%,电化学储能性能远远优于其他2种LMO。即使是在高温55 ℃下,由Mn₂O₃得到的LMO也表现出明显优于其他2种材料的高倍率性能和抗衰减性能。     

熔盐法合成电化学性能优异的富锂层状正极材料Li1.5Ni0.25Mn0.75O2.5

采用氢氧化物共沉淀和熔盐法相结合的方法制备得到了电化学性能优异的富锂锰基Li_1.5Ni_0.25Mn_0.75O_2.5正极材料。借助X射线衍射（XRD）分析、扫描电镜（SEM）、感应耦合等离子体原子发射光谱（ICP-AES）、X射线光电子能谱（XPS）、电化学阻抗谱（EIS）和恒电流充放电测试等表征手段对材料的颗粒形貌、晶体结构和电化学性能进行了系统研究。XRD结果表明该材料具有完善的α-NaFeO₂层状结构（空间群为R3m）和较低的Li⁺/Ni²⁺阳离子混排。电化学性能测试表明该材料的首次不可逆容量损失较小,且倍率性能和循环稳定性能十分优异。具体而言,在2.0~4.8 V,0.1C时的首次不可逆容量损失为50 mAh·g^-1（首次库伦效率84%）;在10C时的放电比容量还能达到102 mAh·g^-1;在0.5C下循环100次后,放电比容量为205 mAh·g^-1（容量保持率90%）。     

纳米锡锌复合氧化物贮锂材料的合成和性质

用液相沉淀-热解法合成了一系列结构和组成不同的锂离子电池纳米锡锌复合氧化物贮锂材料, 通过XRD、TEM和电化学测试对材料进行了表征. 测试结果表明, 非晶态ZnSnO3负极材料的初始可逆贮锂容量为844 mA·h/g, ZnO·SnO2负极材料的初始可逆贮锂容量为845 mA·h/g, SnO2·Zn2SnO4复合物负极材料初始可逆贮锂容量为758 mA·h/g, 循环10周后, 三者的充电容量分别为695, 508和455 mA·h/g, 表明非晶态结构的锡锌复合氧化物具有较好的电化学性质, 随着样品中晶体的形成, 该类型负极材料的贮锂性能下降.     

LiFePO4/C正极材料的液相合成及电化学性能研究

尝试对共沉淀法进行改进, 利用自制的加料装置合成了橄榄石型LiFePO₄/C复合正极材料. 应用X射线衍射(XRD)、扫描电镜(SEM)、X射线能谱(EDS)、循环伏安(CV)以及恒电流充放电测试等方法对目标材料进行了结构表征和电化学性能测试. 实验结果表明采用该法得到的样品具有单一的橄榄石结构, 样品形貌规则, 粒径细小均匀. 改性后的材料具有较高的首放容量及良好的循环稳定性能. 0.1C倍率下充放电测试表明, 其首次放电比容量超过145 mAh•g^－1, 50次循环后, 容量没有明显衰减. 0.2C和0.5C倍率下的平均放电容量分别为130及120 mAh•g^－1, 循环过程中样品表现出较好的循环稳定性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.