Thermal Energy Storage and Heat Transfer of Nano-Enhanced Phase Change Material (NePCM) in a Shell and Tube Thermal Energy Storage (TES) Unit with a Partial Layer of Eccentric Copper Foam

Thermal energy storage units conventionally have the drawback of slow charging response. Thus, heat transfer enhancement techniques are required to reduce charging time. Using nanoadditives is a promising approach to enhance the heat transfer and energy storage response time of materials that store heat by undergoing a reversible phase change, so-called phase change materials. In the present study, a combination of such materials enhanced with the addition of nanometer-scale graphene oxide particles (called nano-enhanced phase change materials) and a layer of a copper foam is proposed to improve the thermal performance of a shell-and-tube latent heat thermal energy storage (LHTES) unit filled with capric acid. Both graphene oxide and copper nanoparticles were tested as the nanometer-scale additives. A geometrically nonuniform layer of copper foam was placed over the hot tube inside the unit. The metal foam layer can improve heat transfer with an increase of the composite thermal conductivity. However, it suppressed the natural convection flows and could reduce heat transfer in the molten regions. Thus, a metal foam layer with a nonuniform shape can maximize thermal conductivity in conduction-dominant regions and minimize its adverse impacts on natural convection flows. The heat transfer was modeled using partial differential equations for conservations of momentum and heat. The finite element method was used to solve the partial differential equations. A backward differential formula was used to control the accuracy and convergence of the solution automatically. Mesh adaptation was applied to increase the mesh resolution at the interface between phases and improve the quality and stability of the solution. The impact of the eccentricity and porosity of the metal foam layer and the volume fraction of nanoparticles on the energy storage and the thermal performance of the LHTES unit was addressed. The layer of the metal foam notably improves the response time of the LHTES unit, and a 10% eccentricity of the porous layer toward the bottom improved the response time of the LHTES unit by 50%. The presence of nanoadditives could reduce the response time (melting time) of the LHTES unit by 12%, and copper nanoparticles were slightly better than graphene oxide particles in terms of heat transfer enhancement. The design parameters of the eccentricity, porosity, and volume fraction of nanoparticles had minimal impact on the thermal energy storage capacity of the LHTES unit, while their impact on the melting time (response time) was significant. Thus, a combination of the enhancement method could practically reduce the thermal charging time of an LHTES unit without a significant increase in its size.     

Thermal Charging Optimization of a Wavy-Shaped Nano-Enhanced Thermal Storage Unit

A wavy shape was used to enhance the thermal heat transfer in a shell-tube latent heat thermal energy storage (LHTES) unit. The thermal storage unit was filled with CuO–coconut oil nano-enhanced phase change material (NePCM). The enthalpy-porosity approach was employed to model the phase change heat transfer in the presence of natural convection effects in the molten NePCM. The finite element method was applied to integrate the governing equations for fluid motion and phase change heat transfer. The impact of wave amplitude and wave number of the heated tube, as well as the volume concertation of nanoparticles on the full-charging time of the LHTES unit, was addressed. The Taguchi optimization method was used to find an optimum design of the LHTES unit. The results showed that an increase in the volume fraction of nanoparticles reduces the charging time. Moreover, the waviness of the tube resists the natural convection flow circulation in the phase change domain and could increase the charging time.     

Computational study of a latent heat thermal energy storage system enhanced by highly conductive metal foams and heat pipes

Numerical simulations are performed to analyze the thermal characteristics of a latent heat thermal energy storage system with phase change material embedded in highly conductive porous media. A network of finned heat pipes is also employed to enhance the heat transfer within the system. ANSYS-FLUENT 19.0 is used to create a transient multiphase computational model to simulate the thermal behavior of the storage unit. Copper foam is the porous medium used to enhance the heat transfer and is impregnated with the phase change material, potassium nitrate (KNO₃). The effects of the porosity of the metal foam and the quantity of heat pipes on the thermal characteristics of storage unit have been investigated. The results indicated that increasing the quantity of the embedded heat pipes leads to drastic acceleration of both charging and discharging process. Impregnating the copper foam with potassium nitrate phase change material significantly affects the total charging and discharging times of the storage unit. It was shown that the porosity of the metal foam plays a key role in the thermal behavior of the system during the charging and discharging processes.

     

The Thermal Charging Performance of Finned Conical Thermal Storage System Filled with Nano-Enhanced Phase Change Material

A latent heat thermal energy storage (LHTES) unit can store a notable amount of heat in a compact volume. However, the charging time could be tediously long due to weak heat transfer. Thus, an improvement of heat transfer and a reduction in charging time is an essential task. The present research aims to improve the thermal charging of a conical shell-tube LHTES unit by optimizing the shell-shape and fin-inclination angle in the presence of nanoadditives. The governing equations for the natural convection heat transfer and phase change heat transfer are written as partial differential equations. The finite element method is applied to solve the equations numerically. The Taguchi optimization approach is then invoked to optimize the fin-inclination angle, shell aspect ratio, and the type and volume fraction of nanoparticles. The results showed that the shell-aspect ratio and fin inclination angle are the most important design parameters influencing the charging time. The charging time could be changed by 40% by variation of design parameters. Interestingly a conical shell with a small radius at the bottom and a large radius at the top (small aspect ratio) is the best shell design. However, a too-small aspect ratio could entrap the liquid-PCM between fins and increase the charging time. An optimum volume fraction of 4% is found for nanoparticle concentration.     

Next generation pseudocapacitor materials from sol–gel derived transition metal oxides

Capacitive energy storage is distinguished from other types of electrochemical energy storage by short charging times and the ability to deliver significantly more power than batteries. A key limitation to this technology is its low energy density and for this reason there is considerable interest in exploring pseudocapacitive charge storage mechanisms which offer the prospect of increasing energy density without compromising the power density of electrochemical capacitors. In this paper we review our recent work on using sol–gel synthesis methods to prepare nanostructured transition metal oxides which exhibit increased levels of pseudocapacitance and enhanced energy storage properties. Our work with TiO₂ nanoparticles and mesoporous films of TiO₂ and CeO₂ is highlighted as we use these studies to understand the role of crystallite size, nanoscale porosity and understanding the differences between pseudocapacitance and intercalation processes.     

Charging/discharging of Au (core)/silica (shell) nanoparticles as revealed by XPS

By recording XPS spectra while applying external voltage stress to the sample rod, we can control the extent of charging developed on core-shell-type gold nanoparticles deposited on a copper substrate, in both steady-state and time-resolved fashions. The charging manifests itself as a shift in the measured binding energy of the corresponding XPS peak. Whereas the bare gold nanoparticles exhibit no measurable binding energy shift in the Au 4f peaks, both the Au 4f and the Si 2p peaks exhibit significant and highly correlated (in time and magnitude) shifts in the case of gold (core)/silica (shell) nanoparticles. Using the shift in the Au 4f peaks, the capacitance of the 15-nm gold (core)/6-nm silica (shell) nanoparticle/nanocapacitor is estimated as 60 aF. It is further estimated that, in the fully charged situation, only 1 in 1000 silicon dioxide units in the shell carries a positive charge during our XPS analysis. Our simple method of controlling the charging, by application of an external voltage stress during XPS analysis, enables us to detect, locate, and quantify the charges developed on surface structures in a completely noncontact fashion.     

“One dimensional” double layer. The effect of size asymmetry of cations and anions on charge-storage in ultranarrow nanopores—an Ising model theory

We develop a statistical mechanical theory of charge storage in quasi-single-file ionophilic nanopores with pure room temperature ionic liquid cations and anions of different size. The theory is mapped to an extension of the Ising model exploited earlier for the case of cations and anions of the same size. We calculate the differential capacitance and the stored energy density per unit surface area of the pore. Both show asymmetry in the dependence on electrode potential with respect to the potential of zero charge, related to the difference in the size of the ions, which will be interesting to investigate experimentally. It also approves the increase of charge storage capacity via obstructed charging, which in these systems emerges for charging nanopores with smaller ions.     

高结构稳定性、低泄漏率三维铜@石墨烯复合相变材料的制备

由于能源消费需求的持续增长和传统化学燃料的日益枯竭,对可再生能源的需求日益迫切。以地热能、太阳能为代表的可再生能源脱颖而出。然而,这些能源的应用易受到天气、季节、地点和时间的影响,具有不稳定性、随机性、波动性和间歇性。储能技术是解决上述问题的有效途径,它可以在需要的时候储存或释放能量。在各种储能技术可选材料中,相变材料(PCMs)是智能热能管理和便携式热能领域的有力候选者。大多数相变材料都存在导热系数低、环境污染、熔点泄漏等问题,因此有必要将相变材料封装到支撑骨架材料中。事实上,支撑材料在应用中仍面临着一些重大挑战。首先,骨架材料应能抵抗相变材料在相变过程中的体积变化,即具有良好的结构稳定性。其次,还应具有较高的导热系数和较低的泄漏率。石墨烯气凝胶(GA)已被证明是提高相变材料形状稳定性的有效支撑骨架,但相变引起的泄漏和网络结构的脆性是制约其应用的关键问题。在此,我们提出了一种双脉冲电镀的强化策略,用于制备铜@石墨烯气凝胶(Cu@GA)作为相变储能骨架材料。这一结构设计中,石墨烯气凝胶上的石墨烯片层上均匀地镀上了铜层,且不同片之间被铜镀层所连接。这种铜增强石墨烯气凝胶网络结构赋予复合材料良好的导热性和坚固的骨架稳定性,有利于增强相变换热和抑制相变过程中的泄漏。此外,通过真空浸渍法将十八胺(ODA)封装在Cu@GA骨架中,获得了结构稳定性高、泄漏率低的复合相变材料(Cu@GA/ODA),保证了ODA在Cu@GA骨架材料中的均匀分散和填充。通过比较复合相变材料的重量变化,研究了不同骨架对复合相变材料泄漏率的影响。优化后的复合相变材料(CPCM)Cu@GA/ODA经20次储热、放热循环后,泄漏率降低至19.82% (w,质量分数),而GA/ODA和GOA/ODA为骨架的复合相变材料的泄漏率分别为80.31% (w)和72.99% (w)。为了探讨这种影响的原因,用扫描电子显微镜(SEM)观察了循环后骨架的形貌。铜/石墨烯气凝胶(Cu@GA)骨架材料没有明显的收缩或坍塌,仍可以保持完整的三维网络结构,而氧化石墨烯气凝胶(GOA)和石墨烯气凝胶(GA)的骨架材料三维结构不复存在,且在氧化石墨烯/石墨烯片能够观察到明显的裂隙。铜涂层可以提高骨架的微观结构稳定性,有利于提高结构稳定性,降低复合材料的泄漏率。同时,该研究为构建理想的金属增强石墨烯气凝胶复合骨架材料铺平了新的道路,该复合材料具有优异的综合性能,可用于未来的相变储能、多孔微波吸收和储能应用。     

A Redox-Active 2D Metal–Organic Framework for Efficient Lithium Storage with Extraordinary High Capacity

Metal–organic framework cathodes usually exhibit low capacity and poor electrochemical performance for Li-ion storage owing to intrinsic low conductivity and inferior redox activity. Now a redox-active 2D copper–benzoquinoid (Cu-THQ) MOF has been synthesized by a simple solvothermal method. The abundant porosity and intrinsic redox character endow the 2D Cu-THQ MOF with promising electrochemical activity. Superior performance is achieved as a Li-ion battery cathode with a high reversible capacity (387 mA h g⁻¹), large specific energy density (775 Wh kg⁻¹), and good cycling stability. The reaction mechanism is unveiled by comprehensive spectroscopic techniques: a three-electron redox reaction per coordination unit and one-electron redox reaction per copper ion mechanism is demonstrated. This elucidatory understanding sheds new light on future rational design of high-performance MOF-based cathode materials for efficient energy storage and conversion.     

A Redox‐Active 2D Metal–Organic Framework for Efficient Lithium Storage with Extraordinary High Capacity

Metal–organic framework cathodes usually exhibit low capacity and poor electrochemical performance for Li‐ion storage owing to intrinsic low conductivity and inferior redox activity. Now a redox‐active 2D copper–benzoquinoid (Cu‐THQ) MOF has been synthesized by a simple solvothermal method. The abundant porosity and intrinsic redox character endow the 2D Cu‐THQ MOF with promising electrochemical activity. Superior performance is achieved as a Li‐ion battery cathode with a high reversible capacity (387 mA h g^?1), large specific energy density (775 Wh kg^?1), and good cycling stability. The reaction mechanism is unveiled by comprehensive spectroscopic techniques: a three‐electron redox reaction per coordination unit and one‐electron redox reaction per copper ion mechanism is demonstrated. This elucidatory understanding sheds new light on future rational design of high‐performance MOF‐based cathode materials for efficient energy storage and conversion.     

Quantized Double‐Layer Charging of Iron Oxide Nanoparticles on a‐Si:H Controlled by Charged Defects in a‐Si:H

Sequential single‐electron charging of iron oxide nanoparticles encapsulated in oleic acid/oleyl amine envelope and deposited by the Langmuir‐Blodgett technique onto Pt electrode covered with undoped hydrogenated amorphous silicon film (a‐Si:H) is reported. Quantized double‐layer charging of nanoparticles is detected by cyclic voltammetry as current peaks and the charging effect can be switched on/off by the excess of negative/positive charged defect states in the a‐Si:H layer. The particular charge states in a‐Si:H are created by the simultaneous application of a suitable bias voltage and illumination before the measurement.     

锂离子电池三维多孔Cu6Sn5合金负极材料的制备及其性能

以三维多孔泡沫铜为基底, 通过直接电沉积的方法制备锂离子电池Cu6Sn5合金负极材料. 发现合金表面大量的微孔和“小岛”不仅增大电极的表面积, 而且显著缓解充放电过程中的体积变化. 测得三维多孔Cu6Sn5合金的初始放电(嵌锂)容量为620 mAh·g-1, 充电(脱锂)容量为560 mAh·g-1, 库仑效率达到90.3%, 具有较好的循环性能. 扫描电子显微镜(SEM)结果显示, 在泡沫铜基底上制备的Cu6Sn5合金电极具有比通常的铜片基底更好的结构稳定性, 经过50 周充放电循环后无明显的脱落现象.     

Interactions of hydrophilic silica nanoparticles and classical surfactants at non-polar oil-water interface

The interfacial and bulk properties of submicron oil-in-water emulsions simultaneously stabilised with a conventional surfactant (either lecithin or oleylamine) and hydrophilic silica nanoparticles (Aerosil?380) were investigated and compared with emulsions stabilised by either stabiliser. Emulsions solely stabilised with lecithin or oleylamine showed poor physical stability, i.e., sedimentation and the release of pure oil was observed within 3 months storage. The formation and long-term stability of silica nanoparticle-coated emulsions was investigated as a function of the surfactant type, charge, and concentration; the oil phase polarity (Miglyol?812 versus liquid paraffin); and loading phase of nanoparticles, either oil or water. Highly stable emulsions with long-term resistance to coalescence and creaming were formulated even at low lecithin concentrations in the presence of optimum levels of silica nanoparticles. The attachment energy of silica nanoparticles at the non-polar oil-water interface in the presence of lecithin was significantly higher compared to oleylamine in line with good long-term stability of the former compared to the sedimentation and release of oil in the latter. The attachment energy of silica nanoparticles at the polar oil-water interface especially in the presence of oleylamine was up to five-times higher compared to the non-polar liquid paraffin. The interfacial layer structure of nanoparticles (close-packed layer of particle aggregates or scattered particle flocs) directly related to the free energy of nanoparticle adsorption at both MCT oil and liquid paraffin-water interfaces.     

Nanoparticles as structural and functional units in surface-confined architectures

The nanoscale engineering of functional chemical assemblies has attracted recent research effort to provide dense information storage, miniaturized sensors, efficient energy conversion, light-harvesting, and mechanical motion. Functional nanoparticles exhibiting unique photonic, electronic and catalytic properties provide invaluable building blocks for such nanoengineered architectures. Metal nanoparticle arrays crosslinked by molecular receptor units on electrodes act as selective sensing interfaces with controlled porosity and tunable sensitivity. Photosensitizer/electron-acceptor bridged arrays of Au-nanoparticles on conductive supports act as photoelectrochemically active electrodes. Semiconductor nanoparticle composites on surfaces act as efficient light collecting systems, and nanoengineered semiconductor 'core-shell' nanocrystal assemblies reveal enhanced photoelectrochemical performance due to effective charge separation. Layered metal and semiconductor nanoparticle arrays crosslinked by nucleic acids find applications in the optical, electronic and photoelectrochemical detection of DNA. Metal and semiconductor nanoparticles assembled on DNA templates may be used to generate complex electronic circuitry. Nanoparticles incorporated in hydrogel matrices yield new composite materials with novel magnetic, optical and electronic properties.     

Physically and chemically bound H2O in the α-C2S hydrate structure

In this paper, a fundamental practical unit, namely the wedge-shaped enclosure, is proposed as a novel and efficient latent heat storage unit for thermal energy storage. The enthalpy–porosity method that treats the solid and liquid zones as a single domain is employed. Effect of the mushy zone constant C on melting is analyzed and a suitable value is obtained by comparing the numerical results with experimental data in the literature. A series of simulations are conducted to analyze the transient melting coupled with natural convection as well as the heat transfer process. Fourteen units those have different length ratios between top and bottom of the enclosures are investigated and compared by the analysis of transient temperature fields, vertical velocity distributions, and evolution of the melting fronts. It is found that the length ratio n dramatically affects the full melting time and heat transfer intensity. An enclosure of n = 5.5, which has the shortest completion time and the highest heat transfer intensity, is determined as the optimal unit. Compared with the base geometry (n = 1), charging time of the optimal unit (n = 5.5) decreased by 32.8 %, while the heat transfer intensity increased by 45.7 %. This is a significant improvement in the field of latent heat storage.     

Nanoparticle assembly on patterned "plus/minus" surfaces from electrospray of colloidal dispersion

Selective deposition of metal (Au) and oxide (SiO2) nanoparticles with a size range of 10-30 nm on patterned silicon-silicon oxide substrate was performed using the electrospray method. Electrical charging characteristics of particles produced by the electrospray and patterned area created by contact charging of the electrical conductor with non- or semi-conductors were investigated. Colloidal droplets were electrosprayed and subsequently dried as individual nanoparticles which then were deposited on substrates, and observed using field emission-scanning electron microscopy. The number of elementary charge units on particles generated by the electrospray was 0.4-148, and patterned area created by contact charging contained sufficient negative charges to attract multiple charged particles. Locations where nanoparticles were (reversibly) deposited depended on voltage polarity applied to the spraying colloidal droplet and the substrate, and the existence of additional ions such as those from a stabilizer.     

锂离子电池快充石墨负极研究与应用

相较于传统燃油汽车,电动汽车缓慢的充电速度始终制约了其进一步推广。为电动汽车实现“加油式”快速充电能够缓解充电桩的使用压力,增加电动汽车的应用场景和市场占有率。因此,亟需开发出具有快速充放电能力的高性能锂离子电池。石墨因其低廉的价格和优异的电化学性能已经在锂离子电池负极领域得到了广泛的商业化应用,然而其较低的嵌锂电位导致在快充过程中出现析锂,损害电化学性能的同时会带来安全隐患。因此,必须对石墨进行改良处理,以适应快充技术的需要。本文系统介绍了近年来石墨负极快充化改良领域的研究进展,从成分设计,形貌调控,结构优化,电解液适配等方面进行了评述,并总结了快充石墨面临的挑战,展望了其发展前景,为推动快充技术的商业化应用提供了借鉴。     

锂离子电池快充石墨负极研究与应用

Driven by the excessive environmental pollution caused by the over-use of non-renewable fossil-derived energy, renewable energy and electrochemical energy storage devices have made great progress in the past decades. Electrochemical energy storage devices, such as lithium-ion batteries, have the advantages of high capacity, long life cycle, and good safety performance; therefore, they have been used in various applications. For example, economical and environment-friendly electric vehicles have recently taken up increasing market share. However, when compared with vehicles propelled using fossil-derived energy, the slow charging speed of electric vehicles has always restricted their further promotion. The realization of rapid charging for electric vehicles can alleviate the high-pressure usage of charging piles as well as increase the application and market share of electric vehicles. Therefore, it is important to develop high-performance lithium-ion batteries with rapid charge and discharge capacities. The fast-charging capacity of lithium-ion batteries is limited by the slow migration of lithium ions in the electrode and the electrode/electrolyte interface. Therefore, the key to developing fast-charging lithium-ion batteries lies in the successful design of suitable electrode materials. Because of its low cost and excellent electrochemical performance, graphite has been widely used to develop the cathode of lithium-ion batteries. However, the migration of lithium ions in graphite is slow, resulting in large polarization during the high-current charge and discharge processes. In addition, the low lithium intercalation potential of graphite leads to lithium precipitation during fast charging, which can decrease the electrochemical performance and cause potential safety hazards. Therefore, graphite must be improved to meet the needs of such fast-charging devices. In this article, we systematically introduce the research progress made in recent years within the scope of rapid-charging improvement of graphite(-based) cathodes and then highlight the modification strategies for graphite with the goal of achieving functional coating, desired morphological and structural design, optimized electrolyte properties, and an improved charging protocol. Additionally, this article evaluates the advantages and disadvantages of the modification strategies as well as their application prospects. The scheme of functional coating for modifying graphite must simplify the process and improve production efficiency to meet the needs of industrial development. Morphology design should ensure satisfactory initial Coulomb efficiency, while the improvement of the electrolyte properties and optimization of the charging protocol need to consider the commercialization costs. Finally, this paper proposes further evaluation of the effects of the modification strategies based on soft-pack or cylindrical batteries to strengthen the commercialization prospect of the modification strategies.      

基于离子液体的超级电容在3 V及65 oC老化条件下的铝碳界面效应

相比于传统乙腈电解液体系的超级电容器,离子液体基超级电容器具有工作窗口电压高,能量密度大,不可燃等优点,适用于碳中和时代清洁但不稳定电力领域的大规模储能。然而,目前的工作主要集中在对纽扣型离子液体-超级电容器的研究上,有关软包式离子液体-超级电容器的长循环寿命评测的报道较少。构建可靠的超级电容器用于长时间测试或在高温下开展加速老化测试,应考虑集流体/电极界面的良好接触,以最小化电荷转移电阻。本文以包覆不同碳层的泡沫铝为集流体,研究了超级电容器新系统中的碳-铝界面效应。通过环氧树脂薄膜碳化得到的均匀无定形碳层,相比通过PVDF粘附石墨烯碳层,赋予了铝相和碳相更强的相互作用。此外,为了充分挖掘大离子尺寸的离子液体电解液的潜力,本文采用介孔碳电极实现离子在介孔间的快速扩散。因此,本工作首次制备了由介孔碳电极、离子液体电解液和覆碳三维泡沫铝集流体组成的新结构软包式超级电容器。以自制的容量为37 F的不同软包式超级电容器件,通过3 V、65 ^oC、500 h加速老化试验,研究了其时间依赖性的电化学性能,包括CV测试、恒流充放电测试、电容值、接触电阻、电化学阻抗谱等。相比石墨烯包覆的泡沫铝基器件,无定形碳层包覆的泡沫铝基器件表现出更高的电容保持率。此外,我们还对ESR进行了等效电路拟合,并深入分析了接触电阻、电荷转移电阻、韦伯电阻,研究了C-Al界面对高能量密度超级电容器的高性能和稳定性的影响。500小时老化测试前后的极片表征证实了上述结果。高温、高压条件使粘附石墨烯碳层的泡沫铝界面结构不可靠。而泡沫铝表面原位包覆的碳层在老化过程中表现出较强的相互作用和稳定的结构。这些坚实的数据为面向高能量密度、高功率密度和长循环寿命,进一步优化高窗口电压超级电容器提供了充足的信息。     

Achieving high electric energy storage in a polymer nanocomposite at low filling ratios using a highly polarizable phthalocyanine interphase

Polymer nanodielectrics have become attractive for practical applications such as electric energy storage and electromechanical actuation. However, to enhance the apparent dielectric constant of polymer nanodielectrics, a significant amount (>30 vol %) of spherical particles needs to be incorporated into the polymer matrix. As a consequence, melt-processing of polymer nanodielectrics into uniform thin films becomes difficult at such a high filler content, and electric breakdown strength will greatly decrease. In this work, we describe a three-phase composite approach towards high energy density nanodielectrics at low filling ratios. In this approach, a highly polarizable tetrameric metallophthalocyanine (TMPc) initiator is coated onto 68 nm BaTiO₃ nanoparticles, from which poly(methyl methacrylate) (PMMA) brushes are grafted using atom transfer radical polymerization for the nanoparticles to be uniformly dispersed in a poly(vinylidene fluoride-co-hexafluoropropylene) [P(VDF-HFP)] matrix. For comparison, two-phase P(VDF-HFP)/BaTiO₃ composites without the TMPc interfacial layer are also prepared. Owing to the high polarizability of the TMPc interface layer, the three-phase composite films exhibit higher dielectric constant and thus higher energy density than the two-phase composite films at volume-filling ratios below 5 vol %. Therefore, these high energy density three-phase nanodielectrics with a low filling ratio are promising for melt-processing into thin dielectric films. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1669–1680