Temperature-programmed hydrogenation (TPH) and in situ Mössbauer spectroscopy studies of carbonaceous species on silica-supported iron Fischer-Tropsch catalysts

Carbonaceous surface species and bulk iron carbides formed under realistic Fischer-Tropsch synthesis (FTS) conditions on moderately dispersed, active silica-supported iron catalysts (Fe/SiO2, FePt/SiO2, and FePtK/SiO2) were characterized. Bulk iron phase compositions were determined by M?ssbauer spectroscopy and phase transformations of carbonaceous species during pretreatment with CO, H2, or H2/CO and following reaction were characterized using temperature-programmed hydrogenation (TPH). Isothermal transient rates of FTS were also measured for catalysts after different pretreatments. Six surface and bulk carbonaceous species were quantitatively identified from combined TPH and M?ssbauer spectra of the FePtK catalyst. They include, in order of decreasing reactivity, (a) adsorbed, atomic carbon; (b) amorphous, lightly polymerized hydrocarbon or carbon surface species; (c) bulk epsilon' and chi carbides (Fe(2.2)C and Fe(2.5)C); and (d) disordered and moderately ordered graphitic surface carbons. A correlation between the amount of reactive alpha-carbon (C(alpha)) and initial catalytic activity was established. The method of Li et al. for measuring irreversible chemisorption of CO does not appear to provide quantitative measurements of active site densities on silica-supported iron. Models, based on this and previous work, are proposed for iron phase and carbon phase transformations in silica-supported iron during pretreatment, FTS, and postreaction passivation/oxidation.     

甲烷氧化偶联含锂多元复合氧化物催化剂的失活机理

对甲烷氧化偶联反应活性较高的多元复合氧化物催化剂（Ｌｉ－Ｔｉ－Ｌａ，Ｌｉ－Ｍｎ－Ｌａ，Ｌｉ－Ｎｉ－Ｌａ）的稳定性和失活机理进行了初步探讨，利用ＸＲＤ，ＩＲ，ＸＰＳ和Ｏ２－ＴＰＤ等方面对催化剂进行了表征，结果表明，催化剂在高温及反应气氛的作用下，表面锂的流失，使体相晶格中的锂向表面扩散，导致含锂活性相结构的分解（或部分分解），从而减少了体相相氧空位和生氧种的数量，降低了晶格氧的活动性，致使催化剂活必     

硅对铁基费-托合成催化剂的影响

用共沉淀法制备了一系列不同硅含量的铁基催化剂,采用N2吸附和原位X射线衍射对催化剂进行了表征,在固定床反应器中考察了催化剂的费-托合成反应活性、选择性和稳定性.结果表明,含硅的催化剂具有较大的比表面积和较小的平均孔径,在CO还原及费-托合成反应中生成的碳化铁物种的稳定性比不含硅的催化剂高.在费-托合成反应中,不含硅的催化剂具有较高的初始活性,但易失活;含硅的催化剂具有较低的初始活性,但稳定性较高.Fe7C3是活性最高的碳化铁物种.随着硅含量的增加,催化剂的费-托合成反应更易生成低碳数产物.     

Kinetics studies of nano-structured iron catalyst in Fischer-Tropsch synthesis

Kinetic parameters of nano-structured iron catalyst in Fischer-Tropsch synthesis (FTS) were studied in a wide range of synthesis gas conversions and compared with conventional catalyst. The conventional Fe/Cu/La catalyst was prepared by co-precipitation of Fe and Cu nitrates in aqueous media and Fe/Cu/La nanostructure catalyst was prepared by co-precipitation in a water-in-oil micro-emulsion. Nano-structured iron catalyst shows higher FTS activity. Kinetic results indicated that in FTS rate expression, the rate constant (k) increased and adsorption parameter (b) decreased by decreasing the catalyst particle size from conventional to nano-structured. Since increasing in the rate constant and decreasing in the adsorption parameter affected the FTS rate in parallel direction, the particle size of catalyst showed complicated effects on kinetic parameters of FTS reaction.     

Fischer-Tropsch synthesis by nano-structured iron catalyst

Effects of nanoscale iron oxide particles on textural structure, reduction, carburization and catalytic behavior of precipitated iron catalyst in Fischer-Tropsch synthesis (FTS) are investigated. Nanostructured iron catalysts were prepared by microemulsion method in two series. Firstly, Fe2O3, CuO and La2O3 nanoparticles were prepared separately and were mixed to attain Fe/Cu/La nanostructured catalyst (sep-nano catalyst); Secondly nanostructured catalyst was prepared by co-precipitation in a water-in-oil microemulsion method (mix-nano catalyst). Also, conventional iron catalyst was prepared with common co-precipitation method. Structural characterizations of the catalysts were performed by TEM, XRD, H2 and CO-TPR tests. Particle size of iron oxides for sep-nano and mix-nano catalysts, which were determined by XRD pattern (Scherrer equation) and TEM images was about 20 and 21.6 nm, respectively. Catalyst evaluation was conducted in a fixed-bed stainless steel reactor and compared with conventional iron catalyst. The results revealed that FTS reaction increased while WGS reaction and olefin/paraffin ratio decreased in nanostructured iron catalysts.     

STUDIES OF MULTICOMPONENT COMPLEX OXIDE CATALYST FOR OXIDATIVE COUPLING OF METHANE Ⅷ.DEACTIVATION OF Li-DOPED Li-Me-La (Me=Ti,Mn,Ni)MULTICOMPONENT OXIDE CATALYST

The deactivation of highly active multicomponent oxide Li-La-Me(Me=Ti,Mn,Ni)catalyst at high reaction temperature has been studiedThe surface and bulk structure of the catlysts were characlerized by meansof XRD.IR.XPS.BET.O_2-TPD.etc The results show that the deactivationof the catalyst at high reaction temperature is mainly due to the loss ofsurface lithium As a result the ditfusion of lithium from bulk to surfaceleads to the decomposition of the active phase containing lithium whichlowers the number of oxygen yaeanctes and decreases the mobility of latticeoxygen.     

Effect of Manganese Incorporation Manner on an Iron-Based Catalyst for Fischer-Tropsch Synthesis

A systematic study was undertaken to investigate the effects of the manganese incorpo- ration manner on the textural properties,bulk and surface phase compositions,reduction/carburization behaviors,and surface basicity of an iron-based Fischer-Tropsch synthesis(FTS)catalyst.The cata- lyst samples were characterized by N_2 physisorption,X-ray photoelectron spectroscopy(XPS),H_2(or CO)temperature-programmed reduction(TPR),CO_2 temperature-programmed desorption(TPD),and M(?)ssbauer spectroscopy.The FTS performance of the catalysts was studied in a slurry-phase continuously stirred tank reactor(CSTR).The characterization results indicated that the manganese promoter incor- porated by using the coprecipitation method could improve the dispersion of iron oxide,and decrease the size of the iron oxide crystallite.The manganese incorporated with the impregnation method is enriched on the catalyst's surface.The manganese promoter added with the impregnation method suppresses the reduction and carburization of the catalyst in H_2,CO,and syngas because of the excessive enrichment of manganese on the catalyst surface.The catalyst added manganese using the coprecipitation method has the highest CO conversion(51.9%)and the lowest selectivity for heavy hydrocarbons(C_(12 )).     

醋酸仲丁酯加氢反应中Cu/B/Ca/Al_2O_3催化剂的失活及再生

Cu/B/Ca/Al2O3催化剂在长达1 118 h的催化醋酸仲丁酯加氢反应中出现了明显的失活.经过对比分析反应前、后和再生催化剂的组成、形貌和结构,发现金属铜粒子在长时间反应后无明显聚集,醋酸仲丁酯加氢反应中部分氧化钙向醋酸钙转变而引起催化剂结构的改变以及有机物种在催化剂表面的沉积是其失活的根本原因.失活后的催化剂经过350℃空气焙烧再生能够有效消除表面沉积的醋酸钙和有机物种,基本恢复催化剂的结构及其催化醋酸仲丁酯加氢反应的性能.     

低温高活性熔铁催化剂上的超临界相费托合成反应

在固定床反应器中超临界相条件下研究了熔铁催化剂上的费托合成反应,发现在超临界介质中反应物和产物更容易扩散,较好地抑制了催化剂表面非活性碳的沉积,从而提高了费托合成反应中的CO转化率和烯烃选择性,增加了链增长因子,降低了甲烷选择性.同时,考察了超临界介质、反应温度、压力、H2/CO比和空速等条件对费托合成反应的影响.结果表明,C5-8正构烷烃在催化剂活性温度下都是适宜的超临界介质.当温度和压力都在介质的临界点以上时,介质表现出较好的传质与传热性能,可改善费托合成反应性能.     

还原温度对Fe-Mo催化剂性质及F-T合成性能的影响

研究了还原温度对Fe-Mo催化剂性质及费托(F-T)合成性能的影响。采用N₂物理吸附、X射线衍射、穆斯堡尔谱和H₂程序升温脱附技术对催化剂进行了表征。结果表明,随还原温度升高,金属铁晶粒粒径增大,金属铁上的H₂吸附量先升后降;催化剂还原度提高,反应态催化剂碳化铁含量递增。催化剂F-T合成性能在280 ℃、1.5 MPa、2 000 h^-1、合成气H₂/CO比为2.0条件下在固定床反应器中测试。反应结果表明,随还原温度提高,催化剂接近稳态时的活性和重质烃选择性(C₅⁺)先升后降,而甲烷选择性则先降后升。350 ℃还原催化剂具有最佳F-T合成反应性能。     

CO2加氢合成甲醇Cu/ZrO2催化剂的失活因素

采用低温氮气吸脱附、X射线衍射(XRD)、电镜(TEM)以及热重差热(TG-DSC)等手段,对不同反应时间下Cu/ZrO₂催化剂的物理结构、微观形貌以及积炭情况进行了表征,分析了催化剂的失活原因。结果表明,造成催化剂失活的主要因素是活性组分烧结;其次,表面积炭覆盖其活性中心也造成催化剂活性在一定程度上的降低;而催化剂比表面积对其活性的影响较小。     

Stability and reactivity of ϵ-χ-θ iron carbide catalyst phases in Fischer-Tropsch synthesis: controlling μ(C)

The stability and reactivity of ?, χ, and θ iron carbide phases in Fischer-Tropsch synthesis (FTS) catalysts as a function of relevant reaction conditions was investigated by a synergistic combination of experimental and theoretical methods. Combined in situ X-ray Absorption Fine Structure Spectroscopy/X-ray Diffraction/Raman Spectroscopy was applied to study Fe-based catalysts during pretreatment and, for the first time, at relevant high pressure Fischer-Tropsch synthesis conditions, while Density Functional Theory calculations formed a fundamental basis for understanding the influence of pretreatment and FTS conditions on the formation of bulk iron carbide phases. By combining theory and experiment, it was found that the formation of θ-Fe(3)C, χ-Fe(5)C(2), and ?-carbides can be explained by their relative thermodynamic stability as imposed by gas phase composition and temperature. Furthermore, it was shown that a significant part of the Fe phases was present as amorphous carbide phases during high pressure FTS, sometimes in an equivalent amount to the crystalline iron carbide fraction. A catalyst containing mainly crystalline χ-Fe(5)C(2) was highly susceptible to oxidation during FTS conditions, while a catalyst containing θ-Fe(3)C and amorphous carbide phases showed a lower activity and selectivity, mainly due to the buildup of carbonaceous deposits on the catalyst surface, suggesting that amorphous phases and the resulting textural properties play an important role in determining final catalyst performance. The findings further uncovered the thermodynamic and kinetic factors inducing the ?-χ-θ carbide transformation as a function of the carbon chemical potential μ(C).     

在Co/SiO2作催化剂的Fischer-Tropsch反应中温度对合成气吸附行为及稳定性的影响

考察了反应温度对Co/SiO2催化剂在Fischer-Tropsch(F-T)合成中合成气吸附行为及稳定性的影响. 采用FTIR, TPSR, XRD, BET, HTPD和TPR等手段对催化剂进行了表征. 结果表明, CO在催化剂表面的吸附为活化吸附, 在270 ℃仍稳定存在, 随着反应温度的升高, 催化剂上发生的主反应由CO加氢链增长反应向Boudouard反应转化, 当反应温度≥350 ℃时, 以Boudouard反应为主. 另外, 随反应温度升高, 金属钴的烧结现象变得明显, 并伴随着硅酸钴或水合硅酸钴物种的生成. 在催化剂的失活因素中, 烧结为主要原因.     

Kinetics of the water-gas shift reaction in Fischer-Tropsch synthesis over a nano-structured iron catalyst

Based on formate and direct oxidation mechanisms, three Langmuir-Hinshelwood-Hougen-Watson (LHHW) kinetic models of the water-gasshift (WGS) reaction over a nano-structured iron catalyst under Fischer-Tropsch synthesis (FTS) reaction conditions were derived and compared with those over the conventional catalyst. The conventional and nanostructured Fe/Cu/La/Si catalysts were prepared by co-precipitation of Fe and Cu nitrates in aqueous media and water-oil micro-emulsion, respectively. The WGS kinetic data were measured by experiments over a wide range of reaction conditions and comparisons were also made for various rate equations. WGS rate expressions based on the formate mechanism with the assumption that the formation of formate is rate determining step were found to be the best.     

完全液相法与溶胶-凝胶法制备Cu-Zn-Al双功能催化剂对浆态床一步法合成二甲醚的催化性能比较

采用完全液相法和溶胶-凝胶法分别制备了组成完全相同的Cu-Zn-Al双功能催化剂,用XRD、氮气吸附-脱附实验和XPS等手段对催化剂的性质进行表征,考察了催化剂对浆态床一步法合成二甲醚反应的催化性能.结果表明,两种方法制备的Cu基催化剂中Cu组分的物相和表面Cu含量明显不同,而催化剂的织构性质基本相同.完全液相法制备的...     

Mo/HZSM-5上甲烷芳构化的诱导期钼物种的部分还原和碳物种的沉积

在无氧条件下,Mo/HZSM-5催化剂表现出良好的催化甲烷芳构化性能.采用脉冲反应,TPSR,TPR,UV Raman,XRD和BET等手段研究了反应的诱导期.BET和XRD结果表明,钼物种较好地分散于分子筛的外表面和孔道内.TPSR和TPR结果表明,在苯产生之前催化剂上至少有两种不同形式的高价钼物种被部分还原.参照MoO3/Al2O3的TPR结果,认为这两种高价钼物种可能是以多聚酸盐和微晶形式存在的MoO3.UV Raman光谱表明,催化剂表面确实存在八面体配位的多聚酸盐铝物种;而XRD没有检测到微晶铝物种的存在.脉冲反应结果表明,预还原可以缩短反应诱导期,而某种类型积碳的存在对缩短反应诱导期更为有利.根据以上结果,认为诱导期是反应活性相逐渐形成的过程,包括高价钼物种的部分还原和碳物种的沉积,而后者可能对反应更为重要.     

甲苯完全氧化反应中含铬催化剂的TPR研究

甲苯完全氧化反应中含铬催化剂的ＴＰＲ研究单绍纯，封雷，孙鸣鸣，伏义路（中国科学技术大学近代化学系，合肥２３００２６）关键词甲苯氧化，三氧化二铬，程序升温还原我们发现，不少非贵金属氧化物催化剂虽然有较好的反应活性，但却不能维持长久，因而影响了其开发应用...     

还原温度与时间对铁基催化剂浆态床F-T合成性能的影响

在浆态床反应器中考察了未还原催化剂以及在240℃和270℃的还原温度下还原时间对Fe/Cu/K/SiO2催化剂F-T合成反应性能的影响,采用Mssbauer谱研究了还原和反应后催化剂的物相组成。结果表明,在240℃延长还原时间或将还原温度升高到270℃均有利于催化剂的还原,270℃还原的催化剂的活性和稳定性明显高于未还原和240℃还原的催化剂,催化剂的运行稳定性与催化剂在反应过程中的流失量有密切关系。催化剂高温还原时烃产物分布倾向于生成低碳数的烃类,在相同的还原温度下,烃产物选择性随还原时间的延长向轻组分方向偏移。     

助剂MgO、CaO对甲烷水蒸气重整Ni/γ-Al_2O_3催化性能的影响

采用固定床装置,考察了以共浸方式引入的助剂MgO、CaO对Ni/γ-Al2O3催化剂在甲烷水蒸气催化重整中的催化反应性能的影响。结果表明,在H2O/CH4/N2的摩尔比为2.86/1/3.28,GHSV为1 800 h-1,反应温度为700℃下,催化剂Ni-CaO/Al2O3催化性能最好;反应初期甲烷转化率可达到96.95%、CO选择性可达68.93%、H2收率可达73.58%。XRD和H2-TPR结果表明,CaO的存在使催化剂中的活性NiO组分增多,还原性和分散性能较好。利用热分析技术对积炭进行考察发现反应10 h后的Ni-CaO/Al2O3催化剂上并未出现导致催化剂失活的炭物种。     

铁/活性炭催化剂上费-托合成反应产物分布的非Anderson-Schulz-Flory特性

 在浆态反应釜中研究了铁／活性炭催化剂上费－托合成（Fischer－Tropschsynthesis,FTS）反应产物分布和链增长几率（Anderson－Schulz－Flory（ASF）链增长几率和本征链增长几率）．产物分布通常在C1处和C2处偏离ASF分布,呈现C1处偏高而C2处偏低的情况．本征链增长几率的研究结果表明,以活性炭为载体的铁基费－托合成催化剂上存在烯烃的再吸附二次反应,使产物分布偏离ASF分布．铁／活性炭催化剂上同时伴随水煤气变换（watergasshift,WGS）反应．XRD检测到铁／活性炭催化剂上存在FexC和Fe3O4两种物相．