混合金属络合物羟基镍铝交联蒙托土的表面酸性及催化性能

用NH_3-TPD,IR技术研究了混合金属络合物羟基镍铝交联蒙托土的表面羟基和表面酸性。考察了制备方法、Al/Ni比对其表面酸性的影响,同时用异丙苯裂解反应表征了其催化性能。结果表明,交联蒙托土存在L酸和B酸,其中以L酸为主。表面酸性可能来源于柱子和表面羟基,柱子的热稳定性对表面羟基,表面酸性均有较大影响。Ni的引入增加了L酸和B酸,取代法制备的样品具有比共聚法的样品更强的酸性。交联蒙托土具有较好的异丙苯裂解性能,Ni的引入使其活性有较大的增加。     

含过渡金属离子的交联蒙托土交联柱中Keggin结构的作用

利用Keggin结构可以发生同晶取代的性质,合成了含过渡金属离子铬、镍的羟基铝交联蒙托土,并运用XRD、~(27)Al-NMR、UV-DRS、XPS、TPR等方法研究了Keggin结构的作用。结果表明,铬、镍都可以和铝生成具有Keggin骨架结构的羟基共聚体,并以此作柱子支撑着蒙托土的层间。铬的取代反应比镍容易发生。共聚法合成出的羟基镍铝交联蒙托土中镍存在两种状态;过量的金属离子对Keggin结构有较大地破坏;Keggin结构的存在增加了交联蒙托土的热稳定性。     

混合金属络合物羟基铬铝交联蒙托土的合成

用取代法和共聚法合成了不向Cr/Al比的混合金属络合物羟基铬铝交联蒙托土,用XRD、DTA考察了其热稳定性,用~(27)Al-NMR、UV、ESR等技术对柱化溶液中铬和铝的状态进行了研究。结果表明,两种方法均合成出结构相近且底面间距d(001)为1.90～2.49nm的羟基铬铝交联蒙托土。发现Cr/Al比对羟基铬铝聚合物的结构、d(001)值、比表面热稳定性均有较大影响;随Cr/Al比的增加,d(001)逐渐增加,热稳定性下降,但在惰性气氛下热稳定性较好(>500℃)。     

混合金属络合物羟基镍铝交联蒙托土的合成

用取代法和共聚法合成了一系列羟基镍铝交联蒙托土。(27)~Al-NMR,UV谱表明两种合成方法都可以得到具有Kessin结构的羟基镍铝柱。取代法合成的交联蒙托土具有均一的(001)面衍射(d_(001)约1.80nm),而共聚法的样品有两种羟基镍铝柱支撑着层间,分别在1.80nm和1.55nm附近产生复合(001)面衍射。用高温老化处理可改善交联蒙托土的热稳定性。经过处理的样品在700℃焙烧后仍可保持稳定,与不经处理的样品相比,热稳定性提高200℃以上。     

羟基铝溶液及铝交联蒙脱土的研究

本文用(27)~Al NMR法和8-羟基喹啉萃取法分别研究了羟基铝溶液中十三聚铝含量的变化规律,还用X-射线衍射法研究了铝交联蒙脱土d_(001)的变化。研究结果表明,铝离子的聚合情况主要由羟铝比决定,而浓度影响不大。随着羟铝比的增加,溶液中单核铝离子含量减少,十三聚铝离子相对含量增加,所得铝交联蒙脱土的d_(001)也随之增大。参照这些变化规律、控制羟基铝溶液的组成,可以制备各种层柱状铝交联蒙脱土复合物。     

交链蒙托土的孔结构及烃类在其颗粒上扩散性能的研究

交链蒙托土是近年来引人瞩目的新型催化材料,但有关其孔结构和烃类分子的吸附与扩散研究的报导甚少.我们采用低温氮吸附容量法研究了中国黑山蒙托土(钙型原土)及Ni,Al,Zr交链蒙托土(Ni-CLB,Al-CLB,Zr-CLB)的孔结构;以石英弹簧作为吸附量探测器的静态重量吸附装置,测定了正辛烷、正癸烷、1,3,5-三甲苯在这些样品上的扩散速率.获得了了解交链蒙托土的孔特性与催化动力学行为的有意义信息.     

表面活性剂改性的铝交联粘土的表征及其水蒸汽减活动力学研究

以聚乙烯醇（ＰＶＡ）为支撑前体合成出改性的铝交联蒙脱土与铝交联累托土。采用ＸＲＤ、Ｎ２低温吸附脱附法、ＩＲ等手段对它们进行了表征，并研究了它们在不同时间与温度条件下的水蒸汽减活动力学。研究结果表明，ＰＶＡ的改性有助于铝交联粘土层间距与比表面积的增大及热稳定性与水热稳定性的提高，粘土基质对其热稳定性与水热稳定性有显著影响，该类催化材料的水蒸汽减活动力学遵循一级衰减反应方程式，其减活速率常数与温度的函数关系可用一个指数函数的经验式表示。     

表面活性剂改性的铝交联累托土的表征及催化性能

用ＸＲＤ，低温Ｎ２吸附／脱附，骨架振动红外光谱等手段对以聚乙烯醇为支撑前体合成的一类新型的表面活性剂改性的铝交联累托土进行了表征，同时对它们进行了柴油催化转化为汽油的微反活性测试，结果表明其热稳定性与催化活性比以传统制备方法合成的铝交联累托土都有明显提高。     

介孔铁铝/蒙脱土复合材料：解离柱撑制备、结构及催化羟基化性能

利用极稀悬浮液中蒙脱土的解离作用并结合柱化技术过程，制备了介孔结构的铝铁/蒙脱土复合材料(Fe-Al/mmt)；并采用粉末X射线衍射、氮等温吸脱附、傅立叶红外光谱、紫外可见光漫反射光谱及苯酚催化羟基化反应表征了其结构和性能。结果显示，铁铝聚合前驱液中铁/铝比影响复合材料中蒙脱土的解离程度，且仅当低铁/铝比时(即Fe/(Fe+Al)物质的量的比介于0.05～0.3)，嵌入解离的蒙脱土片层间的混合铁铝物种呈现能耐温350 ℃的热稳定性；氮等温吸脱附分析反映出这种解离的蒙脱土堆积结构呈现介孔特征，孔径分布窄，介于2.0～2.3 nm；红外分析表明材料表面具有L酸和B酸位，并且L酸位量与嵌入解离的蒙脱土结构中的混合铁铝物种相关；由于结构中混合铁铝物种的存在及相应的Si-O → Fe、Al-O → Fe间的电子跃迁，Fe-Al/mmt材料在紫外区呈现宽泛的能量吸收特征。这些结果说明，由于混合铁铝物种嵌入于解离的蒙脱土片层堆积结构中，形成了“卡片屋”式介孔结构。实验条件下，Fe/(Fe+Al)物质的量的比为0.3的Fe-Al/mmt呈现较佳的催化羟基化性能，苯酚转化率为36.7%，二酚产物选择性32.3%；并且初步表明铝掺杂后，通过铁铝比和表面酸性的调整，材料的部分选择氧化性能可以得到改善。     

Al_2O_3-交联蒙脱土的合成及其对甲苯丙烯烷基化的催化性能

本文研究了蒙脱土在交联前后的面间距、比表面及酸性的变化,并与甲苯丙烯烷基化制伞花烃(Cymene,IPT)的催化活性和关联。当原土经Al_2O_3处理成Al_2O_3交联蒙脱土后,其层间距扩大到0.89nm,比表面增加七倍,酸量增加四倍,成为甲苯丙烯烷基化反应较好的催化剂。在连续进料及常压、低温(50～70℃)的温和条件下,甲苯转化率为～46％,IPT选择率为～68％。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.