复合材料光弹性分析的工程方法

本文在推导均衡光弹性复合材料应力(应变)—光定律的基础上,导出了均衡光弹性复合材料的近似应变—光定律。然后加以推广,提出适用于一般光弹性复合材料的近似应变—光定律.精度分析及实验验证表明:作为工程计算,在采用本文推荐的参数时,光弹性复合材料可视作各向同性材料进行光弹性分析。     

正交异性动态光弹性方法的几个基本问题的研究

文章对适用于动态研究的正交异性光弹性复合材料进行了分析，详细说明了光弹性复合材料中残余双折射的确定方法；基于静态下Ｈｙｅｒ和Ｌｉｕ应力－光性定律，提出了正交异性动态应力－光性定律，并对正交异性材料的动态力学参数及动态光弹性常数给出了实用的标定方法；最后，利用三个单轴压缩试件（０°，９０°及４５°），采用动态应变测量方法，证实了单轴应力状态下正交异性动态应力－光性定律的正确性。     

复合材料光弹性分析的近似方法

本文提出了一种用于光弹性复合材料的简化应变——光学定律。按照这一简化定律。模型材料的主应变差和主应变方向只要利用光弹性实验测出的等差线与等倾线即可求得。些是一种正交异性光弹性分析的近似方法,这一方法所得结果与实验数据比较,最大误差在10％左右。由于采用简化应变——光学定律使得正交异性光弹性分析工作大为简便,因此它是一种适合于工程应用的近似方法。     

双轴应力状态下正交异性动态光弹性应力——光性定律研究

基于静态下Ｈｙｅｒ和Ｌｉｕ表述的正交异性应力－光性定律，在前文中，提出了正交异性光弹性复合材料的动态应力－光性定律并证明了其在单轴应力状态下的正确性。本文旨在进一步考察在双轴应力状态下正交异性动态应力－光性定律的适用性，采用的方法是对纤维增强光弹性复合材料制作的平板模型施加冲击荷载，加载方向与材料纤维方向分别成０°、９０°及４５°角，同时进行正交异性动态光弹性实验和动态应变测量，另外，对该模型进行相应的各向异性介质时域边界元计算。把动态应变测量推算出的应力分量以及时域边界元计算出的应力分量分别代入正交异性动态应力－光性定律，得到随时间变化的双折射条纹级数历程，将其与正交异性动态光弹性实验的结果进行比较。实验及计算结果表明，在三个加载方向下，由这三种方法得到的双折射条纹级数历程均吻合良好，从而证明了前文提出的正交异性动态应力－光性定律在双轴应力状态下的正确性。     

分离主应力的一种新方法—综合法

提出了从光弹性数据中分离主应力的一种新方法——综合法。该法简单实用,容易掌握,有足够的精度,不需单独测定材料条纹值,简化了实验步骤。     

正交异性光弹性应力分离的边界元法

本文对平面正交各向异性复合材料模型引入正应力线性和及边界上正应力线性和流的概念,提出从应力相容方程出发.用边界元法计算正交异性光弹性模型内任一点的正应力线性和位的方法,再与正交异性光弹性法中所给出的应力同的关系结合,即可进行正交异性光弹性应力的分离.最后,对边界元方法的精度进行了讨论.     

单层纤维复合材料的光弹模型初探

本文总结了用显微激光分析仪对一般纤维增强复合材料进行透射式光弹性研究的近期工作.针对纤维复合材料违反传统光弹理论的偏振光学行为,讨论了纤维,基体的双折射率不同及由纤维,基体界面两侧出射的光在Airy斑重叠区发生干涉等问题,从更一般的角度探讨了最近的文章中所提出的新光弹公式中所含两个滞后量的存在性.     

纤维复合材料透射式光弹性方法中的偏振光学问题

本文总结了用显微激光分析仪对一般纤维增强复合材料进行透射式光弹性研究的近期工作。针对纤维复合材料违反传统光弹理论的偏振光学行为,讨论了纤维、基体的双折射率不同以及由纤维与基体的界面两侧出射的光在Airy斑重叠区发生干涉等问题,从更一般的角度探讨了最近的文章中所提出的新光弹公式中所含两个滞后量的存在性。      

用光弹性法测定复合应力强度因子

工程结构裂纹尖端应力强度因子(SIF)由于形状、荷载的复杂性及边界条件的不确定性,难以用解析法得到,数值计算也有困难,而光弹性法弥补了上述方法的不足。本文用环氧树脂制作圆轴模型,采用机加工的方法制作圆轴模型裂纹,然后将加载模型进行应力冻结,通过光弹性实验研究分析了圆轴裂纹尖端应力分布。由于带环形裂纹的圆轴在弯扭组合变形时,离中性轴最远的裂纹尖端处于复合裂纹状态,而三维光弹性应力冻结法是测定复杂三维问题复合裂纹的有效方法。本文用双参数法测定I型应力强度因子,用切片逐次削去法测定Ⅲ型应力强度因子,实验误差较小。     

存在初应力时光弹性复合材料条纹值标定研究

详细研究了存在初应力时光弹性复合材料条纹值标定问题，提出了存在初应力时圆盘标定ｆＬＴ值的方法。分析用直条试件和圆盘试件进行了实例标定，两种标定结果一致，而且标定试验具有自检功能。     

Fractional moiré strain analysis using digital imaging techniques

A new method for analyzing low-order moiréfringe patterns of displacement fields is presented. This method adapts the techniques of half-fringe photoelasticity to moiré and extracts continuous displacement information in the regions between integral fringes. The effectiveness of the technique is illustrated with three examples: a uniform uniaxial field, a tapered specimen in tension, and a disk in diametral compression.     

On the stress-optic law for orthotropic-model materials in biaxial-stress fields

The stress-optic law for othotropic-model materials, proposed by Sampson on the basis of a simple analogy to the isotropic-model materials, is examined for biaxial-stress fields. The stress-optic law is reduced to a simple form for special cases. It is also shown that the zero-order isochromatic fringe corresponds to an isotropic state of stress only in the case of balanced laminates. A glass-fiber-reinforced plastic disk with the glass fibers in only one direction is examined under diametral compression photoelastically and by means of strain-gage rosettes, with the loading direction perpendicular and at 45 deg to the reinforcement direction. The fringe order along the horizontal diameter is computed from the simplified stress-optic law making use of stress values from strain-gage readings and compared with the observed fringe order. Based on a fairly good agreement of the fringe orders, it is shown that a circular-disk specimen can be used to calibrate an orthotropic-model material. The three independent material-fringe values,f _L ,f _T ,f _LT , can be found from measurements of the fringe order and the strains at the center of the disk for the three cases of loading perpendicular, parallel and at 45 deg to the reinforcement direction.     

压缩剪切测试中载荷传递行为的数字光弹性研究

结合光弹性四步彩色相移法,提出改进的六步相移法来计算全场剪应力,对径压缩圆盘实验证实了该方法的正确性,并进一步研究了同质材料连接结构在压缩剪切测试中的层间剪切行为。实验结果表明:全场等色线条纹级数和剪应力连续分布且随载荷而增加;中线附近剪应力趋于零,而条纹级数为峰谷。在连接界面上的条纹级数和剪应力出现峰值,特别是在连接界面端部为最高,在最大载荷下可分别达3.5级和2.4MPa,是导致连接界面脱粘开裂的危险区域。连接结构通过层间剪应力进行应力传递,在连接界面上剪应力与外载基本保持平衡。     

A full-field procedure for evaluating the elastic properties of advanced ceramics

In the present paper, a procedure is described whereby the elastic properties of a ceramic material are evaluated during a biaxial flexure test. The disk specimen is supported on three points and loaded by a uniform pressure on the opposite face. The whole displacement field undergone by the upper face, measured by a digital speckle interferometer, is approximated by a set of polynomials whose weights depend on the elastic properties. This dependence, previously determined by finite element analysis, is exploited to derive the values of the elastic properties from the displacement field experimentally detected. The procedure proposed was applied to a silicon carbide specimen.     

冲击载荷下炸药装药动态响应的有限元分析及热点形成机理的数值模拟

对稳态温度场中受冲击载荷作用的炸药药柱进行了弹粘塑性分析。在Ｐｅｒｚｙｎａ本 构模型的基础上，作了适当的补充和修正，将流动参数γ、弹性模量Ｅ均视为温度的函数，动态 有限元计算结果表明，计算曲线和实验曲线有很好的近似。为模拟材料中不均匀性的影响，在 药柱中心引入一孔洞，有限元计算结果给出含孔洞药柱的粘塑性动态响应、药柱网格变形图以 及药柱等温线，可以清楚看出在孔洞附近区域有局部高温产生。本文的本构模型和计算方法对 于研究冲击载荷下炸药装药的力学响应以及炸药装药中热点形成机理的数值模拟提供了良好 的基础。     

动态光弹性方法的主应力分离的研究

本文提出了动态光弹性、动态焦散线实验方法同边界元法结合的混合法，并用这种方法解决了动态光弹性主应力分离的问题，首先对现有的多火花高速摄影系统进行了改造，在动态实验过程中，成功地得到了不同瞬时的清晰的动态光弹性的等差线条纹和动态焦散线系列图像，这样，便可提取不同瞬时的边界应力值、全场主应力差值及边界上的外载。继而提出用Ｌａｐｌａｃｅ变换域上的边界元法来求解在冲击载荷作用下二维弹性模型全场的主应力和。最后，以受冲击载荷作用的圆盘为例，进行实验及边界元法计算，得到了分离的主应力场。     

Photoelastic analysis of frozen stressed specimens using spectral-contents analysis

The complete birefringence, or isochromatic fringe order, in stress-frozen photoelastic models has been found by measuring the spectral contents of idividual points. A calibration procedure is porposed. The effects of nonuniform birefringence and dispersion of birefringence are considered. The results are presented from the analysis of models of a plate with a central hole and a disk subject to three radial loads.     

Shrinkage Measurement in Concrete Materials using Cure Reference Method

This paper describes the details of using Cure Reference Method (CRM) to determine the shrinkage that develops in concrete materials. The technique involves the replication of diffraction grating on the concrete specimen during curing. After demolded, the specimen is stored in a chamber where a specific drying condition is maintained for 6 days. Every day in this period, the specimen is removed from the chamber and a set of the consecutive moiré fringe patterns are recorded with the help of a specially-designed stage. An automated fringe analysis program is developed to obtain the full-field displacement and strain information. Shrinkage as a function of location, time, and drying conditions is measured. A numerical method is developed in order to obtain material properties from the complex geometry used in the tests. The test in different drying condition and the ring test are performed, and their results are compared with FEA to validate the constructed model.     

Calibration of materials for photoelastoplastic models

Photoplasticity is a possible method of analyzing the plastic behavior in a structural member. Various problems attendant with this technique, however, especially those concerning the fundamental relationship between the fringe order and the stress, and the photoelastic material in the plastic range remain to be investigated. A few studies on this relationship in a uniaxial stress state have been presented, but no evaluations have been made in a biaxial stress state, which is considered essential for practical application of the technique. Applying the photoelastic and the moiré methods, the relationship is investigated in detail in this paper in both stress states using a tensile specimen with a central hole. It is revealed that in the plate of polycarbonate there is a linear relationship between the fringe order and the difference of principal strains in the plastic range. Paper was presented at the 1982 SESA/JSME Joint Conference on Experimental Mechanics held in Oahu and Maui, HI on May 23–29.