添加镝的Nd-Fe-B纳米晶单相合金的微结构与磁性能研究

采用单辊快淬法制备了Nd12.3-xDyxFe79.7Zr0.8Nb0.8Cu0.4B6.0(x=0,0.5,1.5,2.5)合金纳米晶单相永磁薄带,研究了合金薄带晶化处理后,成分、组织结构与磁性能之间的关系.X射线衍射分析(XRD)表明,淬态合金主要由非晶相和Nd2Fe14B相组成,完全晶化后由Nd2Fe14B相和少量α-Fe组成.高分辨透射电镜(HRTEM)分析表明,经充分退火后,Nd2Fe14B晶体完整,晶粒间几乎没有边界相.随着Dy含量增加,晶粒尺寸细化,矫顽力大幅提高.x=0.5合金综合磁性能最佳,经过700℃晶化处理10min后,其磁性能为Jr=1.09 T,Hci=1048kA·m-1,(BH)max=169.5 kJ·m-3.     

钇对Nd-Fe-Al-Ni非晶合金热稳定性与晶化行为的影响

采用差示扫描量热法（DSC）、X射线衍射（XRD）和透射电镜（TEM）研究了Y对Nd-Fe-Al-Ni非晶合金热稳定性和晶化行为的影响。结果表明,淬火态的Nd60Fe20Al10Ni10-xYx（x=0,2）合金基本为非晶组织同时还含有少量的淬态相,Y的加入抑制了淬态相的析出。加入Y后,非晶合金的晶化开始温度和晶化峰值温度都向高温方向移动,证明其热稳定性提高。Y的加入改变了合金的晶化方式和最终晶化产物,使非晶基体中析出的晶化相更加弥散圆整细小。并且Y具有在化学上钝化氧杂质的作用,从而抑制了氧的有害作用。利用Kissinger方程获得了Nd60Fe20Al10Ni8Y2非晶合金的晶化开始和晶化峰值激活能分别为1.21和1.16 eV。     

Mg-Cu-Nd贮氢合金的微观组织结构及贮氢性能研究

采用熔体快淬法制备了(Mg72.2Cu27.8)90Nd10的非晶贮氢合金带,用DSC差热分析仪测定了非晶合金带的热稳定性和非晶形成能力,采用透射电镜TEM和X射线衍射仪表征了不同结晶程度的贮氢合金带的微观组织结构.结果表明:非晶(Mg72.2Cu27.8)90Nd10贮氢合金的晶化过程分为3个步骤:首先在170℃生成平均晶粒尺寸为5～10nm Mg2Cu相;当回火处理温度升高至210℃时,非晶(Mg72.2Cu27.8)90Nd10贮氢合金发生了第二步晶化反应,生成了α-Mg相;当回火处理温度升高到335℃以后,非晶贮氢合金已经完全晶化,生成了稳定的Mg2Cu,α-Mg和Cu5Nd相,晶化后的颗粒尺寸有50～80nm.对不同组织结构的(Mg72.2Cu27.8)90Nd10合金的贮氢性能测试表明:完全非晶状态的(Mg72.2Cu27.8)90Nd10合金具有最快的吸氢速率和最高的贮氢量(3.2%(质量分数)).     

载体γ-Al2O3和钐对非晶态NiB合金热稳定性的影响

用化学还原法制备了NiB、NiB/Al2O3和NiBSm/Al2O3三种催化剂，它们都呈非晶结构.用等离子耦合发射光谱仪(ICP)对催化剂组分进行了分析，采用差示扫描量热法（DSC）对三种催化剂进行了热稳定性分析.结果表明，载体的引入使非晶态NiB合金的体相组成中B的含量降低.将非晶态NiB合金负载到γ-Al2O3上,可以明显改善非晶态合金的热稳定性，少量Sm可以进一步提高晶化温度.晶化激活能数据亦表明了载体和Sm对非晶结构具有良好的稳定作用.载体和Sm可能通过不同的作用提高了非晶态合金的热稳定性.     

Er对Al-Ni-Er-Zr非晶合金动力学特性的影响

采用单辊旋淬法首次制备了Al85Ni10ErxZr5-x(x=3,4,5)非晶合金,利用X射线衍射(XRD)证明Al85Ni10ErxZr5-x(x=4,5)结构为完全非晶态,Al85Ni10Er3Zr2合金为部分非晶。应用差示热分析法(DTA)测定该合金的热学参量,分析了其晶化过程。利用Kissinger法计算了非晶合金的晶化激活能。研究了Er的增加对于Al-Ni-Er-Zr系合金非晶形成能力和热稳定性的影响。结果表明:Er的增加提高了该合金体系非晶形成能力和热稳定性。     

非晶Nd8Fe86B6合金快速晶化过程中的组织变化与磁性能

利用高频感应加热,对熔体快淬Nd8Fe86B6非晶薄带进行了快速晶化退火,并对退火后薄带的微观组织及磁学性能进行了分析.结果表明,快速加热可使非晶带迅速晶化.加热速度强烈地影响薄带的组织和磁性能.不同的加热速度下,都有一个最佳的得到较高磁学性能的加热时间与它相配合.当加热工艺为 加热电压5 kV,加热时间10 s时,晶化后的薄带磁性能可达(BH)max=105 kJ·m-3,Br=0.93 T,Hci=258 kA·m-1.     

Nd60Fe20Al8Co10B2大块非晶合金晶化过程中的结构及磁性能变化

利用吸铸的方法制备了Nd60Fe20Al8Co10B2大块非晶合金。采用示差扫描量热法(DSC)，X射线衍射(XRD)，扫描电子显微镜(SEM)和振动样品磁强计(VSM)研究了Nd60Fe20Al8Co10B2大块非晶合金在晶化过程中的微观结构及磁性能的变化情况。Nd60Fe20Al8Co10B2大块非晶合金在低于723K退火时，富Nd相和富Fe相的析出对于合金的矫顽力影响不大。但是，富Fe相的长大使合金的饱和磁化强度和剩磁下降明显。合金完全晶化后，硬磁性迅速消失。     

NiB和NiP超细非晶合金的退火晶化行为及催化性能

 采用X射线吸收精细结构（XAFS）,X射线衍射（XRD）和差热分析（DTA）等方法研究了以化学还原法制备的NiB和NiP超细非晶态合金催化剂在退火过程中的结构变化．XRD结果表明,在300℃下退火时,NiB超细非晶态合金晶化生成纳米晶Ni3B亚稳物相,NiP超细非晶态合金则主要晶化生成金属Ni和部分晶态Ni3P的混合物相;在500℃退火且近于完全晶化的条件下,大部分超细非晶态合金都晶化为金属Ni．XAFS结果定量地说明,对于NiB和NiP初始样品,第一近邻Ni－Ni配位的平均键长Rj分别为0.274和0.271nm,其结构无序度σS很大,分别为0.033和0.028nm,其热无序度σT分别为0.0069和0.0060nm．300℃退火后,晶化生成的Ni3B的Ni－Ni配位的σS降低到初始样品的33％,仅为0.011nm．500℃退火后,NiB样品的结构参数与金属Ni基本一致,但NiP样品的Ni－Ni配位的σS还远大于σT,仍为0.0125nm,表明NiB和NiP超细非晶态合金的退火晶化行为有很大的差别．纳米晶Ni3B催化苯加氢反应的转化率比超细Ni－B非晶态合金或多晶金属Ni更高,表明纳米晶Ni3B中的Ni与B原子组成了苯加氢催化反应的活性中心．     

Nd60Fe20Al10Co10非晶粉末晶化过程及动力学研究

利用机械合金化制备出Nd60Fe20Al10Co10非晶粉末,采用示差扫描量热仪(DSC),X射线衍射(XRD)和振动样品磁强计(VSM)考察了Nd60Fe20Al10Co10非晶的晶化转变过程及其对磁性能的影响规律,用Kissinger方程计算了Nd60Fe20Al10Co10的晶化激活能,从晶化动力学的角度讨论了玻璃形成能力与晶化反应速率常数的关系。结果表明,Nd60Fe20Al10Co10合金的晶化过程为:非晶+α Fe→非晶+α Fe+Nd→非晶+α Fe+Nd+未知相Mx→α Fe+Nd+未知相Mx+Co2Nd+AlCo。晶化激活能E约为173kJ·mol-1。非晶相的的弛豫无序结构是Nd60Fe20Al10Co10具有硬磁性的原因。完全晶化后硬磁性迅速消失。     

Al89Gd7Ni3Fe非晶粉加压成块合金的组织结构与力学性能

研究了Al89Gd7Ni3Fe非晶粉末经不同温度热挤压成块后的组织形貌和相结构，分析了非晶的晶化过程，并考察了该合金的弯曲强度和疲劳性能。结果表明，不同温度热挤压成块合金组织均由面心立方的α-Al、二元金属间化合物Al3Gd和少量三元金属间化合物τ1相组成，α-Al晶粒细小，Al3Gd相呈等轴颗粒状，τ1相呈杆状分布，提高热挤压温度，有利于Al3Gd相的析出，不利于τ1相的形成。与普通沉淀硬化型Al合金相比，热挤压成块Al89Gd7Ni3Fe合金具有极高的强度和优良的抗疲劳性能，不同温度热挤压成块Al89Gd7Ni3Fe合金的弯曲强度均超过1000MPa，提高热挤压温度，合金的强度和疲劳性能也因金属间化合物Al3Gd相含量增加而改善。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.