丁二酸二异辛酯磺酸钠(AOT)/TritonX-100混合反胶束体系中纤维素酶降解纤维素的研究

对于底物不溶于水的纤维素降解反应而言,为了增强纤维素酶的活性,在丁二酸二异辛酯磺酸钠(AOT)/异辛烷反胶束体系中加入非离子表面活性剂TritonX-100进行纤维素降解实验.结果表明,在AOT中加入非离子表面活性剂TritonX-100可以使纤维素酶的活性提高,非离子表面活性剂TritonX-100与AOT的最佳物质的量之比是0.20.考察了水与表面活性剂的物质的量之比(Wo)、不同酸度(pH)和不同温度(T)等其他反应条件对纤维素降解反应的影响.研究结果表明,反应的最佳条件是:Wo为3.3,T为315.11K,pH为5.10.     

NPES/AOT反胶束增溶体系及性质研究

该文以壬基酚聚氧乙烯醚硫酸钠(NPES)与琥珀酸二(2-乙基己基)酯磺酸钠(AOT)复配体系为主表面活性剂,正丁醇为助表面活性剂,以柴油为油相,研究了反胶束增溶体系的粘度和电导率等物理化学性质;利用脉冲核磁共振图谱中水的T2弛豫时间分布曲线,研究了反胶束溶液中水的结合状态和分布,采用正规溶液理论计算了NPES/AOT的相互作用参数β值(-7.78),研究结果表明二者存在较强的协同效应,从理论上解释了二者在反胶束溶液中的最佳比例和协同增效作用.     

染料敏化太阳能电池用琼脂糖基磁性聚合物电解质的电化学性能

以琼脂糖为聚合物基质,N-甲基吡咯烷酮为溶剂,磁性纳米粒子四氧化三铁为无机纳米颗粒添加剂制备了用于染料敏化太阳能电池(DSSC)的磁性聚合物电解质.通过研究不同小分子表面活性剂,聚乙二醇(PEG200)、曲拉通(TritonX-100)、乙酰丙酮和三者混合的表面活性剂对掺杂有1%(w)Fe3O4的磁性聚合物电解质离子电导率的影响,发现PEG200的加入可有效提高琼脂糖基磁性聚合物电解质的离子电导率.同时,对不同PEG200浓度添加下的电解质进行离子电导率测试研究发现:当PEG200加入量为61.8%(w)时,电解质具有最佳的离子电导率(2.88×10-3S·cm-1);对染料敏化太阳能电池进行电化学交流阻抗谱(EIS)测试的结果表明:染料敏化太阳能电池的电子寿命和复合电阻随着PEG200浓度的增加是先增大后减小,最大的电子寿命和复合电阻出现在PEG200浓度为68.3%(w)处.     

高压CO~2对反胶束溶解蛋白质性质的影响

在308.15K下,研究了表面活性剂琥珀酸二(2-乙基己基)酯磺酸钠(Aerosol-Ot,简称AOT)的浓度和水的含量不同时,溶解的CO~2对反胶束溶解牛血清蛋白(BSA)的性质和异辛烷中AOT反胶束稳定性的影响。实验表明,在适当条件下,CO~2可以使反胶束溶液中的蛋白质全部析出。本研究对有关机理进行了初步分析。     

有机盐对水/AOT/醇反相微乳体系电导行为的影响

用二(2-乙基己基)琥珀酸酯磺酸钠(AOT)为表面活性剂研究了以正构醇(己醇、庚醇、辛醇、癸醇)为连续相的微乳体系的电导行为, 结果表明只有水/AOT/癸醇体系有水诱导的电导渗滤现象. 研究了有机盐(胆酸钠、水杨酸钠)及温度对电导行为的影响, 发现庚醇、辛醇体系电导率随胆酸钠浓度的增加而减小, 而癸醇体系电导率不受影响; 庚醇、癸醇体系的电导率随水杨酸钠浓度的增加而增大; 在5～40 ℃范围内lnσ(电导率的自然对数)与温度成很好的线性关系, 无论有机盐存在与否都没有温度诱导的渗滤现象. 根据Arrhenius-type公式估算了体系的电导活化能.     

AHOT/异辛烷反胶束体系制备铁酸钴纳米粒子

分别以阴离子表面活性剂二(2-乙基己基)丁二酸酯磺酸钠(AOT)和新型表面活性剂二(2-乙基己基)羟基丁二酸酯磺酸钠(AHOT)与异辛烷/水构建的反胶束体系为微反应器,合成了CoFe2O4纳米粒子;利用TGA,XRD,TEM等手段对产物进行了表征;讨论了两种表面活性剂构建的反胶束体系对产物合成过程及纳米粒子形貌和尺寸的影响.     

阴离子与非离子表面活性剂复配体系反胶团的电导研究

在SDS/Tween60/正己醇/环己烷/水形成的反胶团复配体系中,电导率(κ)与水和表面活性剂的摩尔比(W0)关系曲线上存在最大值,随着复配体系中SDS的摩尔分数(xSDS)增大,最大增溶水量(W0,max)向W0值更大的方向移动.xSDS≤0.5时,随着xSDS的增大,W0,max所对应的电导率值增大;xSDS≥0.5时,其电导率值减小.在AOT/Tween60/环己烷/水体系中,出现了与SDS/Tween60/正己醇/正己烷/水体系类似的现象,但W0,max所对应的电导率值,随着xAOT的增大而增大,不会出现极大值,两者的差异主要是由于助表面活性剂醇的影响.在SDS/TritionX-100/正己醇/环己烷/水体系中也印证了该结论.     

亚铁氰化钾电催化氧化L-半胱氨酸的电化学行为研究

研究了在0.10 mol/L Na2SO4溶液中K4Fe(CN)6在玻碳电极(GCE)上电催化氧化L-半胱氨酸(L-Cys)的电化学行为。在-0.2~0.6 V的电位窗口内,L-Cys在GCE上的直接电化学氧化过程迟缓,不易直接发生氧化反应。在K4Fe(CN)6作用下,在0.23 V处出现一个不可逆的氧化峰,且氧化峰电流明显增大。研究结果表明,K4Fe(CN)6对L-Cys的氧化具有良好的电催化作用。电催化氧化峰电流Ipa随扫描速度的增大而增大,且与扫描速率平方根(v1/2)呈线性关系,表明该电催化氧化反应是受扩散控制的电化学过程。催化氧化峰电流与L-Cys浓度在4×10-5~2×10-3mol/L范围内呈良好的线性关系(R=0.9966)。该催化反应过程中电子转移系数α=0.5568,运用计时电流法(CA)得到该电催化氧化的速率常数k为(7.19±0.05)×102(mol/L)-1.s-1。     

AOT/Triton X-100混合反胶束体系中假丝酵母脂肪酶催化蓖麻油水解的活性

研究了二(2-乙基己基)琥珀酸磺酸钠(AOT)/Triton X-100混合反胶束体系中假丝酵母脂肪酶(candida rugosa lipase)催化蓖麻油水解的反应. 考察了Triton X-100占总表面活性剂的摩尔分数(x(Triton X-100))、水与总体表面活性剂的摩尔比(ω0)、pH值、反应温度以及底物蓖麻油的浓度等因素对酶活性的影响. 研究结果表明, 加入非离子表面活性剂Triton X-100可以使假丝酵母脂肪酶的活性得到显著提高, 但是当底物蓖麻油的浓度大于0.24 mol·L-1时, 会对假丝酵母脂肪酶产生抑制作用.     

反胶束体系中合成聚苯胺-无机物复合纳米微粒

利用阴离子型表面活性剂2-乙基己基琥珀酸钠(AOT)形成的反胶束作为微反应器合成了聚苯胺-氯化银和聚苯胺-硫酸钡复合纳米粒子;考察了搅拌因素和不同合成步骤对聚苯胺-硫酸钡尺寸及形态的影响;并利用TEM, IR, UV-vis, XRD和四探针电导率仪对产物进行了表征.研究结果表明,反胶束法可以有效地应用于有机-无机复合纳米材料的制备.     

Electrochemical behavior of nitrogenated nanocrystalline diamond electrodes

Nitrogenated nanocrystalline diamond films with controlled conductivity are deposited from microwave plasma in CH₄-Ar-H₂-N₂ gas mixtures. They are characterized using atomic force microscopy, Raman spectroscopy, and electrophysical measurements. Their electrochemical properties are studied by cyclic voltammetry and electrochemical impedance spectroscopy. Kinetic parameters of reactions in [Fe(CN)₆]^3-/4- redox system are determined. The character of electrode behavior is controlled by the degree on nitrogenation. With the increasing of the nitrogen content in the reaction gas mixture (from 0 to 25%), the potential window somewhat narrows, the background current increases, the reversibility of reactions in the [Fe(CN)₆]^3-/4- redox system increases. By and large, the transition occurs from the electrochemical behavior of a “poor conductor” to that of a metal-like electrode.     

Cu(II) promoted oxidation of L-valine by hexacyanoferrate(III) in cationic micellar medium

The kinetics of Cu(II) accelerated L-valine (Val) oxidation by hexacyanoferrate(III) in CTAB micellar medium were investigated by measuring the decline in absorbance at 420 nm. By adjusting one variable at a time, the progression of the reaction has been inspected as a function of [OH⁻], ionic strength, [CTAB], [Cu(II)], [Val], [Fe(CN)₆³⁻], and temperature using the pseudo-first-order condition. The results show that [CTAB] is the critical parameter with a discernible influence on reaction rate. [Fe(CN)₆]^3- interacts with Val in a 2:1 ratio, and this reaction exhibits first-order dependency with regard to [Fe(CN)₆³⁻]. In the investigated concentration ranges of Cu(II), [OH⁻], and [Val], the reaction demonstrates fractional-first-order kinetics. The linear increase in reaction rate with added electrolyte is indicative of a positive salt effect. CTAB significantly catalyzes the process, and once at a maximum, the rate remains almost constant as [CTAB] increases. Reduced repulsion between surfactant molecules' positive charge heads brought on by the negatively charged [Fe(CN)₆]^3-, OH⁻, and [Cu(OH)₄]^2- molecules may be responsible for the observed drop in CMC of CTAB.     

Electrochemical Behavior of K3[Fe(CN)6] on the Electrode Coated with Modified Multi‐Walled Carbon Nanotubes

The electrochemical behavior of K₃[Fe(CN)₆] was studied on an ITO electrode that was coated with β‐cyclodextrin (CD) modified multi‐walled carbon nanotubes (MWNTs) and with carboxyl modified multi‐walled carbon nanotubes (MWNT‐COOHs). MWNT‐COOHs showed an excellent electrocatalytic effect on the redox of K₃[Fe(CN)₆] while MWNT‐CDs had a subdued effect on the electrochemical response of K₃[Fe(CN)₆]. It is probably due to mismatching between K₃[Fe(CN)₆] and cyclodextrin, which hampers the contact of K₃[Fe(CN)₆] with carbon nanotubes. Moreover, the electrochemical behavior of K₃[Fe(CN)₆] on the MWNT‐COOHs coated ITO electrode at various scan rates also was measured. The results indicated that both potential difference between redox peaks and peak current of K₃[Fe(CN)₆] increased with increasing scan rate. A good linearity of peak current versus scan rate was observed.     

Reversible control of self-assembly of a diblock copolymer supporting Wittig reagent

The reversible control of self-assembly of a diblock copolymer supporting Wittig reagent was attained by changing the volume ratio of the mixed solvent. Poly(4-vinylbenzyltriphenylphosphonium chloride)-block-polystyrene (PPCl-b-PSt) self-assembled into micelles with the PPCl block cores in C₆H₆. The micelles were completely dissociated into unimers by the addition of CH₃CN at a 5/5 volume ratio of C₆H₆/CH₃CN. As a result of further increasing the CH₃CN, the reversed micelles with the PPCl block shells were produced. The copolymer served as the Wittig reagent for 9-anthracenecarboxaldehyde to produce a block copolymer with the pendent anthracene. The resulting copolymer also provided micelles in C₆H₆.     

Elektrochemisches Verhalten von Redox-Systemen in Lösungsmittelgemischen, 2. Mitt.: Das System K4[Fe(CN)6]-K3[Fe(CN)6] in Fettsäure-Wasser-Gemischen

Zusammenfassung Es wurden die elektrochemischen Eigenschaften des Redox-Systems K₄[Fe(CN)₆]-K₃[Fe(CN)₆] in Ameisensäure-Wasser-, Essigsäure-Wasser-, Propionsäure-Wasser- und n-Buttersäure-Wasser-Gemischen untersucht. Die Veränderungen des Redoxpotentials, der Leitfähigkeit und der Dielektrizitäts-konstante wurden studiert.Es wurde bewiesen, daß die Potentialveränderung des Redox-Systems bei kleiner Säurekonzentration (n _s<0,6–0,7) vor allem durch die Wasserstoffionen-Konzentration der Lösung bestimmt wird. Mit der Zunahme der H⁺-Konzentration nimmt die Aktivität des [Fe(CN)₆]^4– in größerem Maße ab als die des [Fe(CN)₆]^3–.Bei großer Säurekonzentration beeinflußt dagegen hauptsächlich die Anionsolvatation durch das Lösungsmittelgemisch die Verschiebung des Redoxpotentials. Die Solvatation ruft eine Strukturveränderung hervor, wodurch die Elektronen-population der Lösungsmittelmoleküle in der Nähe der Cyanoferrat-Ionen abnimmt, die Elektronen-Acceptor-Wirkung des Lösungsmittels wächst. Dieser Prozeß bewirkt in bekannter Weise die Zunahme des Redoxpotentials.

---

The electrochemical behaviour of redox systems in mixed solvents, II.: TheK ₄[Fe(CN) ₆]-K ₃[Fe(CN) ₆] system in fatty acid-water mixtures

The electrochemical behaviour of the K₄[Fe(CN)₆]-K₃[Fe(CN)₆] system has been investigated in mixtures of water with formic, acetic, propionic and n-butyric acid, resp. The change of the redox potential, the conductivity and the dielectric constant has been studied. It has been proved that the change of the redox potential of the system at low acid concentration (n _s<0.6–0.7) is determined by the H⁺ concentration. Increasing the H⁺ concentration, the activity of the [Fe(CN)₆]^4– decreases in a higher extent than the activity of [Fe(CN)₆]^3–.On the other hand, at high acid concentration the shift in the redox potential is influenced first of all by the anion solvating effect of the solvent. The solvation causes such a change in the structure, that the electron population of the solvent molecules around the [Fe(CN)₆]^4– ions decreases, the acceptor strength of the solvent increases. It is well known that this process causes an increase in the redox potential.

---

---

Mit 7 Abbildungen     

Characterization and application of an electrode modified by mechanically immobilized copper hexacyanoferrate

A newly modified electrode was prepared by mechanical immobilization of copper hexacyanoferrate (CuHCF) on a graphite electrode. The modified electrode was characterized by cyclic voltammetric experiments. The effect of different background electrolytes, pHs and scan rates on the electrochemical behaviour of the electrode has been evaluated. In NH₄Cl two reversible redox peaks were observed. The first redox peak corresponding to Cu⁺/Cu²⁺ is observed only in this medium. The second redox peak corresponds to the Fe(CN)₆ ^4–/Fe(CN)₆ ^3– couple. Both anodic peaks were used for catalytic oxidation of ascorbic acid. As the anodic current for catalytic oxidation was proportional to the amount of ascorbic acid, an analytical method was developed for the determination of ascorbic acid in commercial samples.     

Physicochemical investigation of cobalt–iron cyanide nanoparticles synthesized by a novel solid–solid reaction in confined space

Cobalt–iron cyanide (Co_x[Fe(CN)₆]) nanoparticles have been synthesized by a novel solid–solid reaction in the confined space of dry sodium bis(2-ethylhexyl)sulfosuccinate (AOT) reversed micelles dispersed in n-heptane. The reaction has been carried out by mixing two dry AOT/n-heptane solutions containing CoCl₂ and K₄Fe(CN)₆ or K₃Fe(CN)₆ nanoparticles in the micellar core, respectively. By UV-Vis spectroscopy it was ascertained that, after the mixing process, the formation of stable nanoparticles is fast and complete. Microcalorimetric measurements of the thermal effect due to the Co_x[Fe(CN)₆] nanoparticle formation allowed the determination of the stoichiometric ratio (x) and of the molar enthalpy of reaction in the core of AOT reversed micelles. The observed behavior suggests the occurrence of confinement effects and surfactant adsorption on the nanoparticle surface. Further structural information was achieved by small-angle X-ray scattering (SAXS) measurements. From all liquid samples, interesting salt/AOT composites were prepared by simple evaporation of the apolar solvent. Size, crystal structure, and electronic properties of Co_x[Fe(CN)₆] nanoparticles containing composites were obtained by wide-angle X-ray scattering (WAXS) and X-ray photoelectron spectroscopy (XPS).     

Redox Properties of Ferricyanide Ion on Layer‐by‐Layer Thin Film‐Coated Gold Electrodes; Effects of Type of Polycationic Components in the Film

The surface of a gold (Au) electrode was coated with layer‐by‐layer (LbL) thin films composed of poly(vinyl sulfate) (PVS) and different type of poly(amine)s including poly(allylamine) (PAH), poly(ethyleneimine) (PEI) and poly(diallyldimethylammonium chloride) (PDDA) and redox properties of ferricyanide ion ([Fe(CN)₆]^3?) on the LbL film‐coated Au electrodes were studied. The LbL film‐coated electrodes exhibited redox response to [Fe(CN)₆]^3? ion when the outermost surface of the LbL film was covered with the cationic poly(amine)s while virtually no response was observed on the LbL film‐coated electrodes whose outermost surface was covered with PVS due to an electrostatic repulsion between [Fe(CN)₆]^3? ion and the negatively‐charged PVS layer. The redox properties of [Fe(CN)₆]^3? ion on the LbL film‐coated electrodes significantly depended on the type of polycationic materials in the LbL film. The LbL film‐coated electrodes which had been immersed in the [Fe(CN)₆]^3? solution for 15 min exhibited redox response even in a [Fe(CN)₆]^3? ion‐free buffer solution, suggesting that [Fe(CN)₆]^3? ion is confined in the films. In the buffer solution, redox peaks were observed between +0.1 and 0.4 V depending on the type of polycations in the film. Thus, [Fe(CN)₆]^3? ion can be confined in the film and the redox potential is polycation‐dependent.     

Voltammetric Characterization of Grafted Polymer Modified with ZnO Nanoparticles on Glassy Carbon Electrode

In this study, a grafted polymer (GP) with ZnO nanoparticles (GP/ZnO NPs) was attached on the surface of glassy carbon electrode (GCE), in order to produce a new modified electrode (GP/ZnO NPs-GCE). The gamma irradiation method was used to grafted polystyrene (polymer) with acrylonitrile (monomer), while slow evaporation process was used to prepare the new modified electrode. The cyclic voltammetry (CV) of K₄[Fe(CN)₆] was used to study the electrochemical properties GP/ZnO NPs-GCE. The peak separation (ΔE_pa-c) was 500 mV between the redox peaks of Fe(II)/Fe(III) in an aqueous solution of 1 M KCl and the current ratio of redox current peaks (I_pa/I_pc) was ≈ 1 for the modified electrode. This indicated that the modified electrode has s good reversibility and conductivity, wherefore; it was applied in the voltammetric filed. It was found that the modified electrode GP/ZnO NPs-GCE have a reasonable solubility and stability at various pH medium. Additionally, the sensitivity of the electrochemical analysis by cyclic voltammetric (CV) method is extensively subjected to the pH medium and the scan rate (SR). A couple of redox current peaks of K₄[Fe(CN)₆] in KCl solution was observed with a reversible process: Fe³⁺/Fe²⁺. Finally a good diffusion coefficient of electroactive species (D) for the new modified electrode was found in this study by chronoamperometry method using Cottrell equation.     

The Effect of Adsorption of Ions of the Hexacyanoferrate(II)/(III) Redox Pair on Self-Assembly of Octanethiol at Its Adsorption from Aqueous Solutions on Gold Electrode

The effect of components of the redox pair K₃[Fe(CN)₆]/K₄[Fe(CN)₆] on the dynamics of formation of octanethiol (OT) monolayers from aqueous thiol-containing solutions of 0.1 М NaClO₄ is studied by cyclic voltammetry (CVA). The formation of OT monolayers is shown to depend on the presence of ions of hexacyanoferrate(II)/(III) in solution. Being added to solution, the components of the [Fe(CN)₆]^3–/4– redox pair sharply increase the time of formation of the insulating monolayer OT films and make them less stable. The destabilizing and inhibiting action of [Fe(CN)₆]^3–/4– ions becomes stronger as their concentration in solution increases. The adsorption activity of individual components of the redox pair is assessed. The strong and approximately equal adsorption activity of ions [Fe(CN)₆]^3– and [Fe(CN)₆]^4– on gold in the presence of octanethiol is observed. At the same time, OT and the hexacyanoferrate(II)/(III) ions can be placed in the following row: OT > [Fe(CN)6]^3– ≈ [Fe(CN)₆]^4–. Recommendations are given on how to eliminate the interfering action of the K₃[Fe(CN)₆]/K₄[Fe(CN)₆] redox-pair ions when studying the insulating properties of thiol monolayers on gold.