镀铜铁屑-H_2O_2催化氧化降解含酚废水

采用镀铜铁屑代替传统Fenton体系中的FeSO4作为催化剂,通过改变H2O2与镀铜铁屑的投加量、溶液的pH值、反应温度、反应时间等条件,研究了该体系对处理苯酚废水的影响。结果表明,常温下处理实际含酚印染废水,在pH值为4~6,30%H2O2 12mL/L,镀铜铁屑5g/L,反应时间为45min时,COD去除率可达96%,其CODCr从5827mg/L降至419mg/L,色度从2000降至30,符合国家三级排放标准。     

湿式催化氧化处理含高浓度甲醛的草甘膦废水

草甘膦结晶母液经蒸发或纳滤浓缩回收后,产生大量含有高浓度甲醛的废水,常规的废水处理方法难以达到回用或排放要求.以过量溶液浸渍法制备的Pt-Bi-CeO2/AC为催化剂,采用湿式催化氧化法处理2.5%的HCHO溶液,HCHO去除率高达99.9%以上,COD去除率达到96.6%.采用Pt-Bi-CeO2/AC催化剂对含低浓度草甘膦(PMG,50 mg/L)的生产废水直接进行湿式催化氧化处理,催化剂使用23次后,HCHO去除率稳定在85%左右,COD去除率稳定在87%左右,催化剂具有良好的稳定性.湿式催化氧化处理后的废水可直接回用于PMG生产.采用固定床湿式催化氧化装置处理HCHO溶液以及PMG生产废水,处理效果也非常理想,连续使用720 h,催化剂的稳定性能良好.通过XRD、N2吸附-脱附、HRTEM、ICP-OES和XPS等分析手段对催化剂进行了系统表征.     

Ni^2＋／TiO2介孔材料光催化降解造纸废水影响因素的研究

溶胶-凝胶法合成了不同Ni掺杂量的Ni2 /TiO2介孔复合材料.用X射线衍射(XRD)、透射电子显微镜(TEM)、红外(FT - IR)光谱和N2吸附脱附等对产物结构进行了表征.考察了Ni掺杂量、催化剂的用量、初始pH、外加氧化剂等因素对光催化降解造纸废水的影响.结果表明: Ni2 /TiO2介孔复合材料光催化降解造纸废水的最佳反应条件为:Ni掺杂量为2%、催化剂用量1.5g/L、初始pH=4、通氧;光照4 h后,废水色度去除率达100%; 12 h后,废水CODCr去除率达到83.4%.     

一种复合脱色剂在印染废水中的应用研究

以甲醛、双氰胺、醋酸钠、氯化铵、氯化铝等为原料制备了一种印染废水脱色絮凝剂T-1。采用福州某纺织印染有限公司的印染废水为处理对象,以脱色率为主要考核指标,讨论了T-1的投加量、pH值、废水温度等对絮凝效果的影响。实验结果表明,双氰胺-甲醛缩聚物对印染废水具有优良的脱色絮凝效果,当投加量为100mg/L,废水温度为30℃,pH=8时,处理效果最佳,色度去除率达70%,COD去除率为78.3%。而且其絮凝性能明显优于聚合氯化铝(PAC)、聚合硫酸铝(PAS)絮凝剂。     

UF-两段厌氧处理茶多酚废水的研究

采用前置超滤膜(UF)的两相厌氧工艺对原水COD为18362.6mg/L,荼多酚为3608.3mg/L、色度为2624.2倍的茶多酚生产废水进行为期90d的实验研究.结果表明,当实验压力为0.2Mpa时,膜组件对COD去除率为63.4%,茶多酚去除率为95.1%,色度去除率为93.4%.然后,对两相厌氧工艺的投配率、P含量和酸化段水力停留时间(HRT1)对废水COD、色度与茶多酚去除率和产气率的影响进行了研究.当投配率为15.0%、P含量为38.1mg/L、HRT1=24h,该工艺达到最佳处理效果,出水COD为1288.1mg/L,COD去除率为80.8%,色度为95.6倍,色度去除率为44.6%,残余茶多酚为119.8mg/L,茶多酚去除率为32.3%,产气率为0.85m3/kg COD,与未采用UF预处理的两相厌氧水解工艺相比,COD、色度和荼多酚去除率分别提高23.40%,10.2%和1613%,产气率增加0.15m3/kg COD.     

臭氧氧化深度处理印染废水改造工程实例

采用"前物化-水解酸化-好氧"组合工艺处理高浓度印染废水,新增臭氧氧化工艺进行深度处理,进一步提高废水处理效率。经调试运行结果表明,新增工艺使系统出水COD_(Cr)从100mg/L降至70 mg/L,SS从50 mg/L降至28 mg/L,色度从100倍降至36倍,排放水质达到《纺织染整工业水污染物排放标准》GB 4287-2012的排放标准。通过实际运行表明该系统深度处理的出水水质稳定性好,处理效率高。     

混凝吸附法联合处理小麦麸膳食纤维废水

用聚合硫酸铝铁为混凝剂,阳离子型聚丙烯酰胺为助凝剂,活性炭为吸附剂,采用混凝吸附的方法,处理了小麦麸膳食纤维废水.结果表明当聚合硫酸铝铁(PAFS)的质量浓度为500 mg/L,聚丙烯酰胺(PAM)的质量浓度为10 mg/L,pH为4.21时,混凝处理后的废水COD去除率最大.絮凝后水样经活性炭吸附后COD去除率可达85.82%,色度去除率为100%,浊度去除率为93.03%.     

微波诱导Fe2O3/Al2O3催化剂催化氧化处理水中苯酚

 以γ-Al2O3为载体,采用浸渍-焙烧法制备了Fe2O3/Al2O3催化剂,并将其应用于微波诱导催化氧化处理模拟含酚废水. X射线衍射和X射线荧光光谱测试结果表明,活性组分氧化铁在催化剂中以α-Fe2O3的形式存在,其含量为3.71%. 与载体氧化铝相比,Fe2O3/Al2O3催化剂的比表面积和平均孔径及平均孔容略有降低. 对于100 mg/L的模拟含酚废水,最佳的处理工艺条件为: 微波辐照功率400 W,辐照时间5 min,催化剂加入量60 g/L,H2O2浓度600 mg/L,体系pH＞4. 在此工艺条件下,水中苯酚的去除率达97.98%. 催化剂连续使用20次后苯酚去除率仍达96.34%. 表观反应动力学研究表明,在氧化铁催化剂存在的条件下,微波诱导H2O2产生氧化性极强的羟基自由基,整个反应过程可分为微波诱导阶段和催化氧化阶段,两个阶段的氧化过程均符合一级反应动力学规律.     

淀粉黄原酸酯的合成及应用研究

本文研究了不溶性交联淀粉黄原酸酯(ISX)的合成及应用(处理含锌废水),探讨了几种主要因素对锌离子去除率的影响(不溶性交联淀粉黄原酸酯的用量、反应溶液pH、反应时间等因素)。试验结果表明:在ISX加入量为理论用量的1.3倍、pH值控制在9左右、室温条件下,锌离子去除率可达98%以上,处理后的废水中锌离子质量浓度为0.2 mg/L,达到国家排放标准(0.5 mg/L)。     

印染废水的电化学深度处理及回用研究

针对印染废水水质特性,在PbO₂/Ti阳极、不锈钢板阴极的电解反应器中研究了电化学氧化对印染废水生化出水的处理效果. 试验结果表明,电氧化工艺可以实现化学需氧量（Chemical Oxygen Demand,COD）、氨氮和色度的同步去除. 在电流密度10 mA·cm^-2时电解60 min,废水中COD、氨氮、色度、氯离子浓度以及pH值等指标均可达到GB/T 19923-2005《城市污水再生利用工业用水水质》中工艺与产品用水标准,电流效率达45.6%,吨水能耗4.1 kW·h.     

利用手持技术改进测定乙醇分子结构实验

利用压强传感器代替排水集气法,改进测定乙醇分子结构实验的仪器装置,并探索最佳反应条件。另外,设计两个空白实验,结合压强变化曲线对实验误差进行相关讨论。     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.Novosibirsk Institute of Organic Chemistry, Siberian Branch, Academy of Sciences of the USSR. Translated from Khimiya Prirodynkh Soedinenii, No. 6, pp. 812–816, November–December, 1988.     

光谱仪测试范围的扩展

由于石化行业的生产需要，其材质的使用具有多样性和广泛性，经常会出现顾客委托的测试样品的一个或几个元素跨越光谱仪现有测试程序测量范围的情况。本法通过对光谱仪测试原理的认识，根据光谱仪的测试能力及标样的采集，实现了一个或几个元素测量范围的扩展，并对其测量的影响因素进行了研究。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

物质分配系数的测定实验改进

实验教学目的是从解决实际问题出发,以实验技术训练和实验设计思想培养为目标。介绍了将单一的物质分配系数测定实验改进为综合实验,提高了实验效果及实验资源利用率。     

Calculation of enthalpies of hydrogenation of hydrocarbons

Sets of hydrogen molecule equivalents have been developed which permit the calculation of hydrogenation of different types of carbon-carbon bonds from ab initio total energies (3-21G and 6-31G* basis sets, and, to a more limited extent, for MP2/6-31G* data) of reactants and products. The calculated enthalpies of hydrogenation are in good agreement with experiment for unstrained molecules, with average errors on the order of 2 kcal/mol. The 6-31G* equivalents allow the enthalpies for strained molecules to be calculated accurately, but the 3-21G equivalents do not. The equivalents for both basis sets have been tested by calculating the enthalpies of hydrogenation of carbon-carbon bonds in nitrogen- and oxygen-containing organic molecules, free radicals, and classical carbocations. The results are in good agreement with experiment in most cases.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。