光聚合α-CD组装超分子结构水凝胶的合成与表征

1990年, Harada等[1,2]首先观察到α-环糊精(α-CD)与PEG形成的结晶包结物(ICs). 进一步的研究发现, n=400～10 000的PEG均能与α-CD形成结晶ICs, 其形成速率与n有关, n=1 000的PEG形成ICs的速率最快. 由于α-CD是通过与相邻α-CD的氢键作用、空间立体配位及其疏水空腔与聚合物链形成包结物, 这种包结物也称为多聚准轮烷.     

可再生Fe3O4/CuFeS2/生物质复合降解柱对有机染料的处理性能

采用具有单分散性、 平均粒径分别为(200±0.5) nm和(6.5±0.5) nm的Fe₃O₄纳米微球和CuFeS₂纳米晶与生物质废弃物复合制备出Fe₃O₄/CuFeS₂/生物质复合降解柱. 该降解柱能高效处理有机染料亚甲基蓝(MB)和罗丹明B(RhB), 降解率超过90%. CuFeS₂中的Cu⁺能显著促进芬顿反应, 而Fe₃O₄较强的磁性有利于催化剂的回收. 更重要的是, 再生后的复合柱对有机染料的降解率没有明显降低, 仍可达90%以上. 此外, 该降解柱可充分利用生物质废弃物, 解决其回收利用的难题.     

超声刻蚀法构建分级结构的超疏水表面

在湿法刻蚀和超声空化的基础上, 采用超声刻蚀法制备了具有微纳米分级结构的超疏水表面. 以等体积比的硝酸/乙醇(体积分数为4%)和双氧水(质量分数为30%)的混合溶液作为刻蚀剂, 在室温下对60Si2Mn钢、 60^#钢、 T10钢、 Cr06钢、 65Mn钢和硅钢表面超声刻蚀2~10 min, 构建出多种形貌的微纳米分级结构. 上述表面经氟硅烷修饰后具有超疏水性, 水的表观接触角高达157.0°, 155.8°, 157.4°, 154.9°, 157.6°和156.8°, 滚动角分别为6.5°, 19.2°, 6.1°, 7.8°, 6.7°和7.2°. 与常规刻蚀方法相比, 超声刻蚀的化学刻蚀作用因与空化作用耦合而得到强化和改变, 从而在钢表面构建出分级结构. 由于材料表面微结构形貌和固/液界面接触状态不同, 制得的超疏水表面表现出的润湿行为也不同. 超声刻蚀法简单易行, 成本低廉, 适用于其它金属表面构建微纳米分级结构和超疏水表面.     

水热法制备锂电池Si@C负极材料的工艺优化研究

水热法是广泛应用于锂离子电池Si@C电极材料的一种制备方法,其反应条件是影响产物最终形貌和性能的重要因素, 采取最佳的反应工艺可以大大提升材料的电化学性能。本研究中, 使用葡萄糖作为碳源, 光伏切割废料硅为硅源, 探究了水热法制备核壳结构Si@C电极材料的最优工艺, 分别研究了温度、 原料浓度、 反应时间和原料比例对产物的形貌、 性能的影响以及相互之间的关系, 并得到最佳反应条件。在该条件下(葡萄糖浓度为0.5 mol·L^-1, 硅与葡萄糖重量比为0.3:1, 反应温度190 ^oC, 反应时间9 h), 得到了包覆完整、 粒径适中的Si@C电极材料(CS190-3), 对以该样品为负极的扣式半电池进行电化学测试, 在655 mA·g^-1的电流密度下, 其首圈放电比容量为3369.5 mAh·g^-1, 经过500次循环剩余容量为1405.0 mAh·g^-1。倍率测试中, 在6550 mA·g^-1的电流密度下,其剩余容量为937.1 mAh·g^-1,当电流密度恢复至655 mA·g^-1时,电池放电比容量仍可恢复至1683.0 mAh·g^-1。     

氮掺杂碳原位锚定铜纳米颗粒用于高效氧还原反应催化剂

与贵金属铂基电化学氧还原反应（ORR）催化剂相比,廉价的非贵金属催化剂引起了广泛的关注。本文以壳聚糖作为一种富含氮和碳元素的生物质资源,利用碳浴法成功制备了氮掺杂碳原位负载铜纳米颗粒（Cu/N-C）催化剂。纯壳聚糖碳化得到的样品N-C的比表面积为67.5 m²·g^-1、平均孔径0.14 nm、平均孔体积8.00 m²·g^-1,与之相比,Cu/N-C比表面积可达607.3 m²·g^-1、平均孔径为2.5 nm、平均孔体积为0.40 cm³·g^-1。通过密度泛函理论（DFT）进行计算表明,Cu(111)/N-C的自由能值低于N-C,更有利于氧还原催化进行。在0.1 mol·L^-1 KOH的介质中,Cu/N-C不仅表现出优异的起始和半波电势（分别为0.96 V和0.84 V）,而且还表现出了优异的抗甲醇性能和稳定性,并且Cu元素掺杂量达到1.67wt.%。     

聚氯乙烯表皮成分对加成型硅橡胶固化的影响

采用流变学方法研究了双组分加成型硅橡胶在不同聚氯乙烯(PVC)表皮上的固化动力学,并利用红外光谱、核磁共振波谱、电感耦合等离子体质谱仪等手段分析了PVC表皮成分,以确定导致双组分加成型硅橡胶不固化的具体原因。 结果表明,PVC表皮中导致硅橡胶不固化的主要元素为P元素。 在固定硅橡胶厚度为1 mm的情况下,当PVC表皮中的P元素质量分数低于3×10^-3%时,浇注在其上的双组分加成型硅橡胶依然能固化;而当PVC表皮中的P元素质量分数超过约2.4×10^-2%时,虽然浇注在其上的双组分加成型硅橡胶的中间层依然能固化,但与PVC表皮接触部分的硅橡胶不固化,且不固化层厚度随P元素质量分数增加而增加。 本文还研究了在P元素质量分数低于3×10^-3%的PVC表皮上,降低硅橡胶厚度至微米级时的固化行为,在P元素质量分数低于3×10^-3%的PVC表皮上,当硅橡胶厚度低于2 μm时,硅橡胶出现不完全固化现象。 双组分加成型硅橡胶在含有P元素的PVC表皮表面的固化行为主要是由硅橡胶样品中铂催化剂总含量及PVC表皮中的P元素含量确定的,同时也会受到双组分加成型硅橡胶反应速率以及铂催化剂、P元素在硅橡胶中的扩散速率的影响。     

MoS2/GQDs催化剂的制备及微生物电解池的产氢性能研究

通过水热法合成了一系列MoS₂/GQDs复合材料,并制成碳基复合电极。利用电化学测试手段挑选出最佳电极后用于微生物电解池（MEC）阴极的产氢性能研究。实验结果显示： Na₂MoO₄、半胱氨酸和GQDs的最佳原料配比为375:600:1,制备出的MoS₂/GQDs呈现明显的爆米花样纳米片结构,片层厚度在10 nm左右,当碳纸负载量为1.5 mg·cm^-2时,MoS₂/GQDs碳纸电极的析氢催化能力最佳。在MEC产氢实验中,MoS₂/GQDs阴极MEC的产气量、氢气产率、库仑效率、整体氢气回收率、阴极氢气回收率、电能回收率和整体能量回收率分别为51.15±3.15 mL·cycle^-1、0.401±0.032 m³H₂·m³d^-1、91.16±0.054%、66.64±5.39%、72.44±2.60%、217.26±7.42%和77.37±1.50%,均略高于Pt/C阴极MEC或与之媲美。另外,MoS₂/GQDs具有良好的长期稳定性,且价格便宜,有利于实际应用。     

酚类衍生物的美白和抗氧化活性

一系列酚类衍生物被合成,采用傅里叶变换红外光谱仪(FTIR)、核磁共振波谱仪(NMR)和电喷雾质谱(ESI-MS)等波谱技术对其进行了结构表征,并对其进行美白活性测试。 结果表明,HB-1(0.229±0.026)、HB-3a(0.829±0.135)、HB-3b(0.446±0.047)、HMB-3a(1.747±0.215)、HMB-3b(1.307±0.058)和HPE-4b(2.501±0.261)对酪氨酸酶抑制作用明显优于阳性对照物α-熊果苷(3.60±0.029)。 对显示出美白活性的化合物的抗氧化活性测试结果表明,HB-3b和HMB-3a抗氧化活性与阳性对照物槲皮素和番茄红素相当。 因此该类化合物今后可作为美白剂和抗氧化剂加以开发利用。     

242Pu为稀释剂电感耦合等离子质谱定量分析237Np的可行性理论研究

研究了以242Pu为稀释剂时,电感耦合等离子质谱(ICP-MS)定量分析237 Np的理论可行性。研究结果表明:237 Np和242Pu灵敏度的差异主要是由两者电离度的差异和质量歧视效应引起的。在等离子体温度为7 000～10 000K和样品提升率为50～1 000μL/mL时,经过质量岐视校正后,237 Np和242Pu灵敏度的差异只在于两者电离度的差异,且两者相对差异<1%。以242Pu为稀释剂ICP-MS定量分析237 Np的方法在理论上是可行的。     

马鲛鱼抗氧化肽的纳流液相色谱法分离与筛选

在海洋天然产物中,马鲛鱼是一种重要的高活性抗氧化肽生物源,具有极高的加工附加值。由于鱼体组织的复杂性,活性抗氧化肽成分的提取和筛选对样品制备和分离技术提出了挑战。使用不同蛋白酶对鱼体组织进行酶解时,所获得的活性肽结构及功能活性会有显著的差别。为了获得高活性的抗氧化肽,该研究分别考察了风味蛋白酶、胰蛋白酶、酸性蛋白酶、中性蛋白酶、碱性蛋白酶5种蛋白酶的酶解效果。以二苯代苦味肼基自由基(DPPH·)、羟自由基(·OH)清除率和水解度(DH)为指标,筛选最优水解酶。结果表明,胰蛋白酶酶解液清除DPPH·和·OH能力最强,清除率分别达到88.93%±0.82%和53.09%±0.73%。在单因素试验的基础上,以DPPH·清除率为响应值,以加酶量、酶解温度和时间为函数,进行了三因素三水平响应面试验,获得水解度23.66%、DPPH·清除率93.78%以及·OH清除率62.59%的最优制备条件。纳流液相色谱具有低样品量、低溶剂消耗和高效等优势。为筛选出适合于马鲛鱼内脏抗氧化肽分离分析的固定相,该研究使用1∶1000分流比的纳流液相平台,分别使用反相C18柱(15 cm×100 μm, 5 μm, 30 nm)和强阳离子交换柱(15 cm×100 μm, 5 μm, 100 nm)进行分离,收集、冻干并评测了各组分的抗氧化能力。结果表明,强阳离子交换固定相更适合于马鲛鱼内脏抗氧化肽的分离纯化,并筛选出1个强活性抗氧化肽组分。该组分DPPH·清除力的半抑制浓度(IC₅₀)为0.672±0.051 mg/mL,与纯化前相比提高了13.6倍。该研究报道了纳流液相色谱在海洋天然产物源抗氧化肽分离分析中的应用,并证明了其在活性抗氧化肽成分筛选中的有效性和良好的应用前景。     

Copolymers of tetrafluoroethene with chlorotrifluoroethene and with bromotrifluoroethene

Tetrafluoroethene (TFE)–chlorotrifluoroethene (CTFE) and TFE–bromotrifluoroethene (BTFE) copolymers have been synthesized by solution copolymerization over the entire range of comonomer composition. Crystallinity data are reported and first- and second-order transitions have been investigated by DSC. Glass transition temperatures of TFE-CTFE copolymers vary in a nonlinear fashion in the range defined by the homopolymers conforming best to the Johnston equation; the behavior in the TFE-BTFE system is more linear. Whereas TFE-BTFE copolymers show a steep decrease of melting temperature at higher BTFE content, due to the amorphous character of the polymers, more regular behavior was found for TFE-CTFE copolymers. Enthalpies of fusion are also reported. The results are discussed in relation to copolymer composition and structure and are compared with data on tetrafluoroethene–hexafluoropropene (FEP) fluorocarbon resins.     

Asymmetric sorbents with N-carboxymethyl-L-valine and with N-carboxymethyl-L-aspartic acid

Conclusions The asymmetric sorbents with N-carboxymethyl-L-valine with N-carboxymethyl-L-aspartic acid can be used to resolve racemates by the ligand-exchange chromatography method. Institute of Heteroorganic Compounds, Academy of Sciences of the USSR, Moscow. Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 10, pp. 2378–2380, October, 1976.     

Extraction with supercritical gases in coupling with thin-layer chromatography

Summary Numerous substances can be extracted from samples by supercritical gases, e.g. either carbon dioxide or nitrous oxide in the fluid condition at temperatures of 40° C and pressures between 70 and 400 bar. An apparatus for such solvent-free extraction in the analytical field is described. It is coupled directly with a receiving apparatus for subsequent thin-layer chromatography. Three examples with corresponding chromatograms show the possibilities and advantages of this new coupling procedure.

---

Extraktion mit überkritischen Gasen in Kopplung mit der Dünnschicht-Chromatographie1. Mitteilung: Aufbau der Apparatur, Handhabung und Anwendung

Zusammenfassung Zahlreiche Substanzen lassen sich mit überkritischen Gasen aus Proben fraktioniert abtrennen. Als Gase dienen z.B. Kohlendioxid und Distickstoffoxid im fluiden Zustand, d.h. bei Temperaturen von 40° C und Drücken zwischen 70 und 400 bar. Für derartige lösungsmittelfreie Extraktionen im analytischen Bereich wird eine Apparatur beschrieben. Sie ist direkt mit einer Auffangapparatur zur anschließenden Dünnschicht-Chromatographie gekoppelt. An 3 Beispielen mit entsprechenden Chromatogrammen werden die Möglichkeiten und Vorteile dieser neuen Kopplungsmethode demonstriert.

     

Reactions of indole derivatives with cardioprotective activity with reactive oxygen species. Comparison with melatonin

We have previously reported on the synthesis of novel indole derivatives containing an amine-triazole moiety (1a-d, 2a-c), and their antioxidant activity on in vitro non-enzymatic rat hepatic microsomal lipid peroxidation. Some of the compounds showed protective activity against oxidative injury of ischemic myocardium. In the present paper we investigated the interactions of these derivatives with reactive oxygen species, in order to find a mechanism of their antioxidant capacity and to identify structural characteristics responsible for these properties. These interactions were compared with melatonin, which is also an indole derivative. The antioxidant profiles of the compounds were established by different in vitro protocols as follows: 1) by the interaction of the compounds with the 1,1-diphenyl-2-picrylhydrazyl (DPPH) stable free radical, 2) their scavenging effects on superoxide anions using an enzymic system of xanthine-xanthine oxidase, 3) their inhibitory effects on xanthine oxidase and 4) their ability to scavenge hydroxyl radicals by comparison with dimethyl sulfoxide (DMSO) for *OH. All compounds were found to interact with DPPH, most of them to be superoxide anion scavengers and to be strong hydroxyl radical scavengers. Derivatives 1a and 1d substituted on the nitrogen of the indolic nucleus were found to have better antioxidant properties than the reference compounds used and melatonin.     

Voltammetry with a Fluoride-Selective Electrode with Solid-Phase Reference System

Experimental results obtained in a study of the voltammetric response of an all-solid fluoride-selective electrode based on LaF₃ (Eu²⁺ 0.8 mol %), LaF₃ (Sr²⁺ 5 mol %) and CeF₃ (Sr²⁺ 5 mol %) single crystals brought in contact with Ag, Bi, and Sn metal samples are presented. The method of cathodic inversion voltammetry was applied to study the reduction of La³⁺ and Ce³⁺-cations from the rigid sublattice of solid electrolytes, which determines the threshold of the electrochemical stability of a membrane. Anodic inversion voltammetry was used to investigate the characteristics of solid-phase generation of metal fluorides at the interface between the fluoride-selective electrode and metals.     

Electrochemical sensing with electrodes modified with molecularly imprinted polymer films

This article summarises our work on the development of voltammetric sensors based on molecularly imprinted polymers. Several recognition elements and integration strategies were used:1.membranes electropolymerised at the electrode surface; 2.casting of polymeric membranes by drop-coating a solution of pre-formed polymer (polyphosphazene) and template in a low-boiling-point solvent on to the electrode surface; 3.preparation of composite membranes containing conductive material (graphite or carbon black), acrylic-type molecularly imprinted polymers (small particle size), and PVC as binder; and 4.in-situ polymerisation of a thin layer of acrylic imprinted polymer deposited on the electrode surface by spin coating.All the options evaluated offer the possibility of controlling electrode characteristics such as hydrophobic/hydrophilic character, permeability, or film thickness, which are essential for obtaining good sensor performance.     

Microfibrillated cellulose with sizing for reinforcing composites with LDPE

Microfibrillated cellulose (MFC) fibers were acylated by the sizing agent, alkenyl succinic anhydride (ASA) reagent in an aqueous medium, by simple impregnation. The chemical modification was confirmed by Fourier transform infrared spectroscopy and solid-state ¹³C NMR. All the samples were combined with low-density polyethylene and the morphology, thermal properties, mechanical properties and water absorption behavior of the ensuing composites were investigated. The chemical modification of the MFC with ASA improved the interfacial adhesion with the matrix and hence the mechanical properties of the composites while decreasing their water uptake capacity. In addition, it was shown that the degree of substitution strongly influenced the performance of the composites.     

Multielement analysis with ICP-AES-possibilities for quality control with CRMs

Summary An analysis using Certified Reference Materials (CRMs) together with routine samples is by far the best approach for quality control in multielement analysis of environmental samples. The selection of the correct CRM is thus the first important step for all reliable analysis. The chosen material should have a similar matrix, similar concentration of the element(s) of interest and a sufficient number of well-certified elements. For the analysis of samples from the Environmental Specimen Bank only a few CRMs could be successfully used. These were analyzed for a considerable period of time, together with the routine samples for quality control. The results of these analyses were compared with the certified values.