芘基查尔酮的合成及三阶非线性光学性质

合成了一种新的具有潜在应用价值的非线性光学(NLO)有机材料1-(芘-1-基)-3-(4-二甲氨基苯基)丙烯酮(PMAK),并通过 NMR、IR、MS和元素分析等技术手段进行了表征。 采用溶液Nd:YAG激光技术测定了PMAK的三阶非线性光学性质并确定了相关参数。 纳秒实验结果:折射率n₂=-3.5×10^-17 m²/W,吸收系数β=7.0×10^-10 m/W,极化率χ⁽³⁾=2.54×10^-11 esu,分子超极化率γ=3.44×10^-30 esu;皮秒实验结果:n₂=-2.8×10^-18 m²/W,β=8.3×10^-11 m/W,χ⁽³⁾=2.49×10^-12 esu,γ=3.33×10^-31 esu。     

1-二茂铁基-3-[(9-乙基)咔唑-3-基]丙烯酮的合成及三阶非线性光学性质

合成了一个新的非线性光学(NLO)有机材料1-二茂铁基-3-[(9-乙基)咔唑-3-基]丙烯酮(FCAK),并通过NMR、IR、MS和元素分析等技术手段进行了表征。 采用粉末Nd∶YAG激光技术测定了标题化合物的三阶非线性光学性质并确定了相关参数。 激光脉冲为4 ns时,非线性折射率n₂=-3.5×10^-18 m²/W,非线性吸收系数β=-2.7×10^-11 m/W,三阶非线性极化率χ⁽³⁾=2.04×10^-12 esu,三阶非线性分子超极化率γ=1.1×10^-30 esu。 激光脉冲为21 ps时,n₂=0.55×10^-18 m²/W,β=-0.6×10^-11 m/W,χ⁽³⁾=3.4×10^-13 esu,γ=0.13×10^-30 esu。     

基于二茂铁的两个查尔酮衍生物的合成及超快三阶非线性光学响应

二茂铁是合成新颖有机功能材料的基本单元之一。 本文设计并合成了两个基于二茂铁的同分异构查尔酮衍生物:1-二茂铁基-3-(噻吩-2-基)丙烯酮(a)和1-二茂铁基-3-(噻吩-3-基)丙烯酮(b)。 采用超快激光Z-扫描技术(脉宽180 fs,波长532 nm)测定了化合物a和b的三阶非线性光学性质。 结果表明,化合物a吸收系数β=-2.1×10^-12 m/W,折射率n₂=1.9×10^-19 m²/W,分子超极化率γ=5.37×10^-32 esu;化合物b:β=-1.2×10^-13 m/W,n₂=2.0×10^-19 m²/W,γ=4.48×10^-32 esu。 说明在飞秒激光激发下,电荷转移能够在化合物a和b分子内部快速进行,二者均具有优异的超快三阶非线性光学响应。 在B3LYP/6-311+G(d,p)理论水平下,计算了化合物a和b分子轨道能量、极化率和各基团在前线分子轨道中的占有率。 理论计算结果显示,二茂铁基团在化合物a和b前线分子轨道中占有率分别为97%和98%,对两化合物的非线性光学性能起主导作用。     

氧化石墨烯/富勒烯复合材料增敏多金属离子印迹电化学传感器

制备了一种对Pb(Ⅱ)、Cd(Ⅱ)和Cu(Ⅱ)等多金属离子具有灵敏、选择性响应的新型印迹传感器。 以甲基丙烯酸与乙二胺四乙酸分别为功能单体与配体,乙二醇二甲基丙烯酸酯为交联剂制备出多金属离子印迹聚合物。 采用滴涂法将离子印迹聚合物均匀地修饰至氧化石墨烯/富勒烯复合材料修饰碳电极表面,成功制备出灵敏的多金属离子印迹电化学传感器。 采取循环伏安法、交流阻抗和差分脉冲法等技术对印迹电化学传感器的性能进行表征,结果表明该多金属离子印迹电化学传感器具有良好的选择性。 在1.0×10^-9~5.0×10^-7 mol/L范围内,该多金属离子印迹电极的响应电流与金属离子浓度呈现良好的线性关系,对Pb(Ⅱ)、Cd(Ⅱ)和Cu(Ⅱ)金属离子的最低检测限分别为5.0×10^-10、5.0×10^-10和1.0×10^-10 mol/L。 该多金属离子印迹电化学传感器成功用于实际样品中微量Pb(Ⅱ)、Cd(Ⅱ)和Cu(Ⅱ)等金属离子的检测。     

磺化聚芳醚酮砜/聚芳醚砜噁二唑复合型质子交换膜的制备与性能

为了降低质子交换膜(PEM)的甲醇渗透系数和改善PEM在中高温(80~120 ℃)时的质子传导率, 以自制的磺化度(SD)为100%的磺化聚芳醚酮砜(SPAEKS)与聚芳醚砜噁二唑(PAESO)为原料, 采用溶液共混法制备了SPAEKS/PAESO复合膜, 并用傅里叶变换红外光谱(FTIR)和热重分析(TGA)对其进行了表征. 结果表明, 该复合膜具有较好的化学稳定性和热稳定性. 扫描电子显微镜(SEM)照片显示, 复合膜具有较好的致密结构, 其甲醇渗透系数为3.9×10^-7~6.6×10^-7 cm²/s, 低于SPAEKS的8.7×10^-7 cm²/s. 在100 ℃时复合膜的质子传导率达到0.074 S/cm, 高于SPAEKS膜的0.066 S/cm.     

聚乙烯醇/酸化碳纳米管高亲水性三维孔电极膜的制备与电化学性能

在酸化碳纳米管的基础上, 采用电泳沉积和冷冻-解冻循环交联工艺制备了高亲水性聚乙烯醇/酸化碳纳米管(PVA/a-MWCNTs)水凝胶电极膜. 该电极膜具有三维连通纳米孔结构, 同时还具有高电活性面积、 低表面电荷传递电阻以及良好的扩散通透性等电化学特性. 该电极膜对多巴胺(DA)有很好的电化学响应特性, 并且对多巴胺的电化学还原电流不受抗坏血酸(AA)干扰, 在过量抗坏血酸存在下, PVA/a-MMWCNTs水凝胶电极膜对多巴胺还原电流的一阶导数与多巴胺的浓度在2×10^-6 ~2×10^-3 mol/L范围内呈线性关系, 检出限达到1×10^-6 mol/L, 灵敏度达到12.3 μA/(mmol·L^-1), 同时还表现出了较好的电极稳定性和重现性.     

双组分加成型硅橡胶交联固化过程的流变学研究

采用流变学方法研究了双组分加成型硅橡胶的交联固化过程,并研究了反应温度对反应速率的影响.随着加成反应的进行,体系中的交联程度逐渐增加;反应温度升高,硅橡胶完全交联固化所需时间减少.     

电/离子导体双包覆的LiNi0.8Co0.1Mn0.1O2锂离子电池阴极材料及其电化学性能

高镍三元材料LiNi_0.8Co_0.1Mn_0.1O₂ (NCM)比容量高且成本低, 但材料结构在电化学循环过程中的不稳定性影响了其大规模的应用, 可采用表面包覆的策略来改善材料的结构稳定性, 从而提高其电化学性能. 本工作结合高速固相包覆法和高温烧结法, 分别将电子导体氧化锡锑(ATO)和锂离子导体偏磷酸锂(LOP)共同包覆在NCM材料表面. 双包覆后的NCM材料的电子电导率从2.17×10^-3 Ѕ•cm^-1提高至1.02×10^-2 Ѕ•cm^-1, 锂离子扩散系数也从7.05×10^-9 cm²•s^-1提高至2.88×10^-8 cm²•s^-1. 同时, NCM表面的双包覆层可以在循环过程中阻止电极材料与电解液发生氧化还原反应, 抑制材料不利相变, 减少氧的析出, 稳定材料结构. 电化学性能测试表明, 经过表面包覆后, NCM材料在1 C (180 mA•g^-1)的电流下和2.7~4.3 V (vs. Li/Li⁺)的电压范围内, 循环150周后容量为161.1 mAh•g^-1, 保持率为87.1%, 而在10 C的充放电倍率下具有133 mAh•g^-1的可逆比容量.     

含8-羟基喹啉侧基聚酯及其锌和铝配合物的合成与荧光性质

经多步反应合成3种含8-羟基喹啉侧基聚酯(P7~P9),进一步与无水醋酸锌和六水氯化铝反应,得到6种聚酯锌、铝配合物(P7-Zn~P9-Zn,P7-Al~P9-Al)。 采用元素分析、红外光谱、紫外可见光谱、核磁共振氢谱、凝胶渗透色谱、热重分析仪、差示扫描量热和荧光光谱等技术手段对其结构和性能进行表征。 P7~P9易溶于N,N-二甲基甲酰胺(DMF)、N,N-二甲基乙酰胺(DMAC)、二甲基亚砜(DMSO)和N-甲基吡咯烷酮(NMP),P7-Zn~P9-Zn和P7-Al~P9-Al部分溶于DMF、DMAC、DMSO和NMP。 P7~P9的质均相对分子质量(M_w)为1.79×10⁴、2.14×10⁴和2.52×10⁴ g/mol,相对分子质量分布指数PDI为1.54、1.64和1.72。 P7~P9的5%失重温度分别为291.6、291.3和284.9 ℃,P7-Zn~P9-Zn、P7-Al~P9-Al的5%失重温度分别为348.7、339.2、334.6、316.1、316.7和316.0 ℃。 P7~P9的玻璃化转变温度(T_g)分别为121.8、106.2和86.4 ℃,聚酯锌、铝配合物的T_g均高于180 ℃。 P7~P9的DMF溶液(5×10^-5 mol/L)在413~418 nm处发紫色荧光,P7-Zn~P9-Zn、P7-Al~P9-Al的DMF溶液(5×10^-5 mol/L)分别在509~513和485~487 nm处发强绿色荧光,固体分别在516~519和492~497 nm处发强绿色荧光。 P7~P9、P7-Zn~P9-Zn和P7-Al~P9-Al的荧光量子产率分别为5.5%~8.4%、21%~28%和23%~29%。     

离子选择性微电极用于原位测量离子扩散系数

扩散系数是描述物质扩散过程的重要参数,而用膜池法、放射性或荧光示踪法、分子动力学模拟等现有方法无法原位进行生物体系中离子扩散系数的实时测量。 本文利用离子选择性微电极响应迅速、高选择性、高灵敏度、高空间分辨率、对样品无污染等优势,通过分析单个植物细胞原生质体在培养液中破裂时所形成的离子浓度脉冲信号,建立了相应的点源扩散模型,推导出了描述离子浓度随时间变化的理论公式,并通过该公式对实验测得的脉冲信号进行拟合,得到了离子的扩散系数,从而建立了一种用离子选择性微电极原位测定离子扩散系数的新方法,并将其应用于芦荟细胞原生质体破裂时离子扩散系数的测定,得到了Ca²⁺、Na⁺和K⁺的扩散系数分别为(6.51±0.12)×10^-6、(2.93±0.15)×10^-5和(3.03±0.35)×10^-5 cm²/s。 对比发现,拟合得到的Ca²⁺、Na⁺和K⁺扩散系数均略高于已报道的数值(纯水中),这一现象的产生可能是因为原生质体是在低渗液中吸水膨胀,细胞膜内压力升高产生内外压力差,该压力差会加速细胞破裂时离子的扩散。 这一方法对生物体系无干扰,较好地解决了生物体系中离子扩散系数原位实时测量的难题。     

EFFECTS OF SOME PHENYLETHYNYLSILICON COMPOUNDS ON HEAT-CURABLE SILICONE RUBBER Ⅲ 1, 1, 3, 3-TETRAMETHYL-1, 3-DIPHENYLETHYNYL-DISILOXANE*

We have shown that some phenylethynylsilicon compounds are good cure crosslinkersof heat-curable silicone rubber(HCSR). In this paper the effects of 1, 1, 3, 3-tetramethyl-1, 3-diphenylethynyldisiloxane (TMDPDS) as a crosslinker on HCSR were studied. Thevulcanizates with fine mechanical properties could be obtained with suitable amounts ofTMDPDS. Sol fractions, and crosslinking density of vulcanizates and vulcanizationretardation effect of TMDPDS on hydrosilation curing silicone rubber were also discussed.     

Effect of the platinum catalyst content on the tracking and erosion resistance of addition-cure liquid silicone rubber

An addition-cure liquid silicone rubber (ALSR) with ureido-containing MQ silicone resin (U-MTQ) was prepared by hydrosilylation with platinum catalyst (Pt). ALSR samples were characterized by thermogravimetric analysis (TGA) and thermogravimetry coupled with infrared spectroscopy (TG-FTIR), and the char layers of ALSR samples after inclined plate tracking and erosion test (IPT) were characterized by X-ray photoelectron spectroscopy (XPS). The effects of Pt content (5–100 ppm) on the curing characteristics, mechanical properties and tracking and erosion resistance of ALSR were investigated. It was found that the cure rate increased with increase of Pt content. When the Pt content was 10 ppm or 15 ppm, the ALSR had excellent tracking and erosion resistance, all specimens could pass the 4.5 kV level in IPT, and the erosion rate was only 0.13% and 0.15%, respectively. ALSR samples possessed optimum mechanical properties and thermal stability when the Pt content was 15 ppm. TG-FTIR results showed that ALSR generated less carbonyl compounds (CH₂O) and cyclic oligomers but more methane (CH₄) when the Pt content was 15 ppm. This demonstrated that there were lower levels of the oxidation of methyl groups and the main chain unzipping degradation of ALSR, and more homolysis of Si-CH₃ during the degradation. The XPS results also showed that the macromolecular radicals would further cross-link to form a firm Si-C ceramic barrier to protect ALSR samples under Pt catalysis and high temperature, thus the tracking and erosion resistance of ALSR could be improved.     

Hardness measurements of silicone rubber and polyurethane rubber cured by ionizing radiation

This work investigates the hardness of both silicone rubber and polyurethane rubber cured by ionizing radiation. Shore A hardness is used to characterize the subject elastomers in relation to the crosslinking process. Various formulations of both materials have been investigated in order to achieve the optimum cure conditions. A small amount of a chemical curing agent has been incorporated in some formulations in order to reduce the required dose to achieve full cure conditions. Silicone rubber improved in hardness with increasing absorbed dose, whereas hardness remained constant over a broad range of absorbed doses for polyurethane rubber.     

Rheological study on the cure kinetics of two-component addition cured silicone rubber

The cure kinetics for two-component silicone rubber formed by addition reaction was studied by the rheological method. The influence of reaction temperature (T) on the cure kinetics was explored in detail. It was observed that the data of gel time (t _gel, i.e. the time when the reaction reaches the gel point) or a specific reaction time (t _nc) (defined as the reaction time before which time the influence of confinement of network on the diffusion of reaction components can be neglected) versus T obey certain functional relationship, which was well explained by the cure kinetics model of thermoset network. The cure kinetics for the two-component silicone rubber can be well fitted by the Kamal-Sourour(autocatalyst) reaction model rather than Kissinger model. When the reaction time was before or equal to t _nc, the reaction order obtained by the Kamal-Sourour reaction model was 2, which was consistent with the reaction order inferred from the two components chemical reaction when the diffusion of reaction components was not influenced by the formed cross-linked polymer network. When the reaction time was larger than t _nc, such as to the end of reaction (t _e), the influence of confinement of network on the diffusion of reaction components cannot be neglected, and the reaction order obtained by the Kamal-Sourour reaction model was larger than 2. It was concluded that the confinement effect of network had a greater influence on the cure kinetics of the silicone rubber. The reaction rate constants (k _r) under different temperatures were also determined by Kamal-Sourour reaction model. The activation energy (E) for the two-component silicone rubber was also calculated from the results of lnt _gel, lnt _nc, and lnk _r versus 1/T, respectively. The three values of E were close, which indicated that above analyses were self-consistent.     

硅氮聚合物交联剂交联的室温硫化硅橡胶的热稳定性

利用硅氮聚合物作交联剂使双组分缩合型室温硫化硅橡胶在不需要催化剂存在下硫化，通过对硫化胶老化后的热失重、交联密度和力学性能的测定，表明这种硫化胶的耐温性能由２００℃提高到３５０℃．对硫化胶的降解动力学研究表明：降解反应活化能由７０ＫＪ／ｍｏｌ提高到３３０ＫＪ／ｍｏｌ，这是由于消除了端基引发的主链降解．     

Novel poly(vinyl chloride) based thermoplastic elastomers incorporating vinyl-functionalized silicone rubber

ABSTRACT

Novel poly(vinyl chloride) (PVC) based thermoplastic elastomers were developed by blending with different proportions of vinyl-functionalized silicone rubber. Scanning electron microscopy (SEM) confirmed good compatibility between PVC and silicone rubber which allowed enhancement of the stress-strain behavior. On the contrary to neat PVC, exposure to heat or UV radiation was found not to cause any considerable deterioration to the stress-strain behavior. Fourier Transform Infrared (FTIR) revealed a possible chemical interaction between the blend components involving the vinyl groups from the silicone rubber, which is thought to be the reason for maintaining the mechanical properties unaltered. Further investigation with ultraviolet-visible (UV-Vis.) spectroscopy signified absence of intensive dehydrochlorination usually encountered for PVC after exposure to heat or UV radiation, which indicates a potential stabilizing effect for the silicone rubber and build up of a network structure comprising both hard and soft segments.     

Silicone‐based impact modifiers for poly(vinyl chloride), engineering resins,and blends

Silicone‐based impact modifiers were prepared in a previous study. The modifiers were composed of silicone/acrylic rubber cores and grafted acrylic shells. They improved the toughness of poly(vinyl chloride) (PVC) and poly(methyl methacrylate). The silicone emulsion that was used to produce the silicone‐based impact modifiers was prepared via two routes: emulsion polymerization and bulk polymerization of octamethyltetracyclosiloxane. Many silicone‐based impact modifiers were produced that had different silicone/acrylic rubber characteristics. Through a toughness examination of modified PVC, the best composition of the silicone‐based impact modifiers was obtained, and the silicone content in the rubber composition was 25 wt %. The morphology of the silicone‐based impact modifiers, determined by transmission electron microscopy, was as follows: core and second shell polymers were mainly poly(butyl acrylate), and the first shell polymer was silicone. The silicone‐based impact modifiers were blended with engineering resins such as PVC, polycarbonate (PC), poly(butylene terephthalate) (PBT), and PC/PBT mixtures. The impact strength under standard conditions and after weathering test conditions for blends of the silicone‐based impact modifiers were investigated with respect to two commercially available acrylic and methyl methacrylate/butadiene/styrene impact modifiers. The results showed good weatherability and good toughness under low‐temperature conditions for the silicone‐based impact modifiers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1112–1119, 2004     

硅橡胶/氟橡胶并用胶的制备及力学性能

硅橡胶和氟橡胶作为国防、航天等重要领域的耐热材料一直被人们青睐,但其有着各自地优缺点且价格昂贵,本文尝试将这两种橡胶制成并用胶以解决氟橡胶不耐低温和加工性差的问题,以期增大其使用温度范围。采用机械共混法制备硅橡胶/氟橡胶并用胶,研究了硅橡胶和氟橡胶的混炼工艺、并用比、共硫化体系和硫化条件对并用胶力学性能的影响。结果表明,当硅橡胶/氟橡胶的质量比为10∶90,共硫化体系为3~#硫化剂/过氧化二异丙苯(DCP),一段硫化温度为170℃、硫化压力为10MPa、硫化时间为30min,二段硫化温度为200℃、硫化时间为6h时,并用胶的力学性能达到最好。     

Experimental and numerical investigations of bi-injection moulding of PA66/LSR peel test specimens

Bi-injection moulding is a widely used process to manufacture engineering products and consumer goods. Typically, a thermoplastic is combined with rubber or another thermoplastic to create colour differences or hard and soft areas, respectively. The aim of this study was to optimise the injection parameters and processing conditions for the moulding of two-component standard peel test specimens with suitable functional properties. In this work, all parameters of thermo-rheo-kinetic behaviour were identified to predict the entire filling stage and the effect of a liquid silicone rubber cross-linking reaction during the injection moulding process. The models of Carreau-Yasuda and Isayev-Deng regarding the thermal dependence assumed by Arrhenius’ law were used. In our study, over-injection moulding is simulated and examined using finite element software (Cadmould 3D) to investigate the thermo-rheo-kinetic behaviour and the adhesion of liquid silicone rubber during the filling mould process in over-moulding. Numerical simulation results were then compared with the experimental results, and good agreement was obtained.     

二十四面体Pt纳米晶电极上甲酸解离吸附反应动力学研究

研究了甲酸在二十四面体Pt纳米晶（THHPtNCs）电极表面解离吸附反应过程.电化学原位红外反射光谱结果显示,甲酸在低电位（-0.20V（SCE））即可在THHPtNCs电极上氧化到CO2,同时发生分子内化学键断裂生成吸附态CO物种.运用程序电位阶跃暂态方法定量研究甲酸解离吸附反应动力学,测得5×10^-3mol·L^-1 HCOOH＋0.1mol·L^-1 H2SO4溶液中甲酸在THHPtNCs电极上解离吸附的最大平均速率υamax为13.19×10^-10mol·cm^-2·s^-1,是商品Pt/C催化剂电极上υamax的1.5倍.研究结果揭示了THHPtNCs的反应活性显著高于Pt/C催化剂.