聚氯乙烯表皮成分对加成型硅橡胶固化的影响

采用流变学方法研究了双组分加成型硅橡胶在不同聚氯乙烯(PVC)表皮上的固化动力学,并利用红外光谱、核磁共振波谱、电感耦合等离子体质谱仪等手段分析了PVC表皮成分,以确定导致双组分加成型硅橡胶不固化的具体原因。 结果表明,PVC表皮中导致硅橡胶不固化的主要元素为P元素。 在固定硅橡胶厚度为1 mm的情况下,当PVC表皮中的P元素质量分数低于3×10^-3%时,浇注在其上的双组分加成型硅橡胶依然能固化;而当PVC表皮中的P元素质量分数超过约2.4×10^-2%时,虽然浇注在其上的双组分加成型硅橡胶的中间层依然能固化,但与PVC表皮接触部分的硅橡胶不固化,且不固化层厚度随P元素质量分数增加而增加。 本文还研究了在P元素质量分数低于3×10^-3%的PVC表皮上,降低硅橡胶厚度至微米级时的固化行为,在P元素质量分数低于3×10^-3%的PVC表皮上,当硅橡胶厚度低于2 μm时,硅橡胶出现不完全固化现象。 双组分加成型硅橡胶在含有P元素的PVC表皮表面的固化行为主要是由硅橡胶样品中铂催化剂总含量及PVC表皮中的P元素含量确定的,同时也会受到双组分加成型硅橡胶反应速率以及铂催化剂、P元素在硅橡胶中的扩散速率的影响。     

不同色浆质量分数的水性聚氨酯涂料对聚氯乙烯表皮低温爆破性能的影响

本文制备了一系列不同色浆质量分数的水性聚氨酯涂料,并将其喷涂在汽车仪表板聚氯乙烯(PVC)表皮的背面形成复合材料。 用旋转流变仪表征了涂料的粘度以评价其喷涂性能;用差示扫描量热仪表征了材料的玻璃化转变温度(T_g);利用万能材料试验机表征了材料在-30 ℃条件下的拉伸性能及抗撕裂性能;用动态热机械分析仪表征了材料的损耗比随温度的变化。 结果表明:不同色浆质量分数的涂料都能喷涂,含有涂层材料PVC表皮在-30 ℃低温爆破性能与涂层材料的T_g、低温拉伸性能、抗撕裂性能的关系并不大,而与涂层材料的阻尼性能直接相关。 材料的阻尼性能越好,其低温爆破性能越好。     

青海油砂矿的物理化学特性

油砂矿的物理、化学性质是其开发利用的关键因素之一 ;作者利用多种分析手段 ,揭示了青海出露油砂的特殊有机物化学组成与分布及其物理性质 ,其轻质组分含量很高 ,饱和烃含量高达近一半 ,而胶质、沥青质重组分含量低 (<38 % ) ,H和C原子比甚高 ,直链烷烃分布规整 ,主要集中在C19～C37 范围 ,物理参数处在普通重油范围内 ;该种物理、化学性质独特的出露油砂在全球为首次发现 ,是青海油砂矿特殊的地理地质环境所造成的 ,作者建议其开采宜采用钻井采油和露天开采依次进行的新组合方法     

汽车用聚氨酯减振材料的结构与性能

利用扫描电镜(SEM)对减振材料的微孔结构进行了表征;用万能材料试验机(UMTM)、动态热机械分析仪(DMA)、旋转流变仪表征了减振材料在不同条件下的力学及减振性能.研究发现:不同聚氨酯减振材料进入非线性形变区域的压缩形变大小与微孔的面积占有率相关.我们认为聚氨酯泡沫减振材料在小压缩应变下应力的缓慢增加主要是由微孔的变形引起的,随着压缩应变进一步增加,微孔的变形接近极限,此时应力的快速增加主要由聚氨酯本体的力学性能决定.聚氨酯减振材料的损耗能随着压缩应变的增加而增加,减振性能好的材料具有较大的损耗能.聚氨酯减振材料的损耗角随着压缩频率的增加而略有增加,其影响减振材料在不同使用频率下的减振和产热性能.聚氨酯减振材料的损耗角随着温度的变化而发生变化,耐寒性和耐热性好的材料,损耗角随温度平缓变化的温度范围更宽.当减振材料受到一定的负载后,材料的损耗角降低.     

热塑性聚氨酯共混物的硬度与冲击性能的关系北大核心CSCD

选取了2种分子组成相同硬度不同的热塑性聚氨酯(TPU),将二者共混后得到了不同硬度的TPU共混物,探究了TPU共混物的硬度与冲击性能的关系。通过落球冲击试验、感压纸测试和冲击前后样品表面温度测试对TPU共混物的冲击性能进行表征。当样品的硬度越低时,峰值冲击力越小,冲击持续时间越长,冲击时的最大应变越大,冲击时样品的受力面积增大,对应的冲击时的峰值应力值减小。不同硬度样品的能量耗散比差别不大,但随硬度降低呈现小幅度上升趋势。冲击后的样品表面温度较冲击前有所上升,说明样品通过热的形式耗散了部分能量,各硬度样品的温度差值较为接近,这与不同硬度样品的能量耗散比的变化规律是相似的。所有样品均具有较高的能量耗散比,TPU能耗散大部分冲击能量,具有良好的抗冲击性能。     

氧化石墨烯对聚乙烯醇/硼酸水凝胶流变性能的影响

研究了氧化石墨烯(GO)对聚乙烯醇(PVA)/硼酸(borate)水凝胶线性及非线性流变性能的影响。 通过扫描电子显微镜、硼谱核磁共振波谱以及流变研究了水凝胶的流变性能。 结果表明,GO质量浓度在稀溶液区时,GO片层与PVA链间通过硼酸根离子形成了具有弹性活性的缔合点,有效地提高了水凝胶的平台模量、松弛时间和零切粘度;当GO进一步增加到亚浓溶液区,部分的交联剂被GO的团聚体捕获并处于非弹性活性的缔合状态,处于有效缔合状态的交联剂变少,导致平台模量、松弛时间和零切粘度降低。 稳态剪切测试下,样品在剪切增稠区的粘度增加随着GO添加量的增加明显加强,这与剪切场下取向的氧化石墨烯片层参与网络结构的重排有关。     

双组分加成型硅橡胶交联固化过程的流变学研究

采用流变学方法研究了双组分加成型硅橡胶的交联固化过程,并研究了反应温度对反应速率的影响.随着加成反应的进行,体系中的交联程度逐渐增加;反应温度升高,硅橡胶完全交联固化所需时间减少.     

The effect of particle shape on the structure and rheological properties of carbon-based particle suspensions

The structure and rheological properties of carbon-based particle suspensions, i.e., carbon black(CB), multi-wall carbon nanotube(MWNT), graphene and hollow carbon sphere(HCS) suspended in polydimethylsiloxane(PDMS), are investigated. In order to study the effect of particle shape on the structure and rheological properties of suspensions, the content of surface oxygen-containing functional groups of carbon-based particles is controlled to be similar. Original spherical-like CB(fractal filler), rod-like MWNT and sheet-like graphene form large agglomerates in PDMS, while spherical HCS particles disperse relatively well in PDMS. The dispersion state of carbon-based particles affects the critical concentration of forming a rheological percolation network. Under weak shear, negative normal stress differences(ΔN) are observed in CB, MWNT and graphene suspensions, while ΔN is nearly zero for HCS suspensions. It is concluded that the vorticity alignment of CB, MWNT and graphene agglomerates under shear results in the negative ΔN. However, no obvious structural change is observed in HCS suspension under weak shear, and accordingly, the ΔN is almost zero.     

Rheological study on the cure kinetics of two-component addition cured silicone rubber

The cure kinetics for two-component silicone rubber formed by addition reaction was studied by the rheological method. The influence of reaction temperature (T) on the cure kinetics was explored in detail. It was observed that the data of gel time (t _gel, i.e. the time when the reaction reaches the gel point) or a specific reaction time (t _nc) (defined as the reaction time before which time the influence of confinement of network on the diffusion of reaction components can be neglected) versus T obey certain functional relationship, which was well explained by the cure kinetics model of thermoset network. The cure kinetics for the two-component silicone rubber can be well fitted by the Kamal-Sourour(autocatalyst) reaction model rather than Kissinger model. When the reaction time was before or equal to t _nc, the reaction order obtained by the Kamal-Sourour reaction model was 2, which was consistent with the reaction order inferred from the two components chemical reaction when the diffusion of reaction components was not influenced by the formed cross-linked polymer network. When the reaction time was larger than t _nc, such as to the end of reaction (t _e), the influence of confinement of network on the diffusion of reaction components cannot be neglected, and the reaction order obtained by the Kamal-Sourour reaction model was larger than 2. It was concluded that the confinement effect of network had a greater influence on the cure kinetics of the silicone rubber. The reaction rate constants (k _r) under different temperatures were also determined by Kamal-Sourour reaction model. The activation energy (E) for the two-component silicone rubber was also calculated from the results of lnt _gel, lnt _nc, and lnk _r versus 1/T, respectively. The three values of E were close, which indicated that above analyses were self-consistent.