单体结构对聚合物稳定胆甾相液晶形貌及光电性能的影响

采用紫外光聚合诱导相分离法制备聚合物稳定胆甾相液晶(PSCT),研究了单体4,4′-二[6-(丙烯酰氧基)己氧基]联苯(BAB6)、2-甲基-1,4-二[4-(3-丙烯酰氧基己氧基)苯甲酸基]对苯二酚(HCM-009)、2-甲基-1,4-二[4-(3-丙烯酰氧基丙氧基)苯甲酸基]对苯二酚(LCM)对常黑和常白模式PSCT光电性能的影响。结果表明:BAB6不具备液晶性,与液晶的相容性差,形成的聚合物网络疏松,网孔较大;HCM-009和LCM均具有液晶性,能很好地溶于液晶中。BAB6、HCM-009、LCM 3种单体形成的聚合物网络对液晶分子的锚定作用依次增强,常黑模式PSCT的阈值(饱和)电压减小,下降时间变长,迟滞宽度变大;而常白模式PSCT的驱动电压增大,响应速率变快。     

单体结构对聚合物稳定胆甾相液晶形貌及光电性能的影响

采用紫外光聚合诱导相分离法制备聚合物稳定胆甾相液晶(PSCT),研究了单体4,4′-二[6-(丙烯酰氧基)己氧基]联苯(BAB6)、2-甲基-1,4-二[4-(3-丙烯酰氧基已氧基)苯甲酸基]对苯二酚(HCM-009)、2-甲基-1,4-二[4-(3-丙烯酰氧基丙氧基)苯甲酸基]对苯二酚(LCM)对常黑和常白模式PSCT光电性能的影响。结果表明:BAB6不具备液晶性,与液晶的相容性差,形成的聚合物网络疏松,网孔较大;HCM-009和LCM均具有液晶性,能很好地溶于液晶中。BAB6、HCM-009、LCM 3种单体形成的聚合物网络对液晶分子的锚定作用依次增强,常黑模式PSCT的闲值(饱和)电压减小,下降时间变长,迟滞宽度变大;而常白模式PSCT的驱动电压增大,响应速率变快。     

聚(N-对丙烯酰氧苯甲酰氧基)丁二酰亚胺的合成及其共聚物与血清蛋白的固定化

新的丙烯酸活性酯,N-(对甲基丙烯酰氧苯甲酰氧基)丁二酰亚胺(MBOSu)及N-(对丙烯酰氧苯甲酰氧基)丁二酰亚胺(ABOSu)单体分别由对甲基丙烯酰氧基苯甲酸(MBA)、对丙烯酰氧基苯甲酸(ABA)与N-羟基丁二酰亚胺(HOSu)在环已基羰二亚胺存在下经偶联反应合成。MBOSu及 ABOSu 容易进行均聚合及与MBA或ABA进行共聚合而得到相应的反应性聚合物。P(MBOSu-MBA)共聚物是一个较好的固定化蛋白质的载体。它极易与抗血清(驴抗人A·B·O混合血清)或正常人 A·B·O混合血清反应,形成一种具有较高免疫活性的固定化免疫吸附剂。     

光敏聚合物薄膜光化学性能及其诱导液晶分子取向性能的研究

本文采用动态紫外光谱法测试了含有香豆素光敏基团的聚合物薄膜的光化学性能,考察了不同曝光温度和曝光能量条件下的光敏聚合物的光化学性能,以及不同热处理条件下聚合物薄膜诱导液晶分子取向性能。研究结果表明:在曝光温度为130℃时,聚合物薄膜在最小曝光量下发生光化学反应后产生的光学各向异性ΔA达到最大,并且对应光反应程度DP在45%左右;当曝光能量为320mJ/cm~2和384mJ/cm~2、对应热处理温度为160℃时,聚合物薄膜诱导液晶分子取向所产生的各向异性ΔA和有序度参数S达到最大,分别为0.22和0.048。     

邻苯二甲酸异丙酯酰氧基-丙烯酰氧基-乙酰乙酸乙酯络铝及其聚合物的合成与荧光性质

通过异丙氧基铝和邻苯二甲酸酐、乙酰乙酸乙酯及丙烯酸反应,合成了螯合物单体邻苯二甲酸异丙酯酰氧基-丙烯酰氧基-乙酰乙酸乙酯络铝,由自由基聚合法合成了聚合物,用元素分析仪、VPO、IR、¹HNMR和²⁷AlNMR证实了它们的结构,并研究了它们在DMF中的荧光性质。     

聚合物分散液晶单体4,4′-二[6-(丙烯酰氧基)己氧基]联苯的合成

利用丙烯酰氯代替丙烯酸钾与4,4′-二(6-溴己氧基)联苯反应改进了制备4,4′-二[6-(丙烯酰氧基)己氧基]联苯(BAB6)的合成路线。改进前的反应温度较高,中间产物溶解度小,产物呈淡黄色,收率仅12.4%;改进后在室温反应,中间产物溶解度较高,产物呈白色,收率达到46.8%。采用1HNMR、13CNMR和元素分析对中间体和BAB6结构进行了表征。由改进后合成的单体,制备了具有快速响应的聚合物分散液晶(PDLC)膜,响应时间约2ms。扫描电子显微镜观察的结果表明,PDLC中形成了聚合物网络结构。     

官能团化己内酯与丙交酯无规共聚物的合成与降解性能

研究了官能团化新型己内酯单体的合成及其与丙交酯无规共聚物的降解性能. 首先, 环己酮和N-异丙基丙烯酰胺通过Michael加成反应合成了2-(N-异丙基酰胺乙烯基)-环己酮; 然后, 以间氯过氧化苯甲酸为氧化剂, 通过Baeyer-Villiger氧化反应, 制备带有酰胺官能团的己内酯单体6-(N-异丙基酰胺乙烯基)-ε-己内酯; 最后, 在异辛酸亚锡[Sn(Oct)₂]的催化下与丙交酯开环聚合, 得到新型己内酯与丙交酯的无规共聚物. 采用¹H NMR, SEC和DSC表征了聚合物的结构和热力学性能. 同时通过黏度法、失重法和SEM对该聚合物的降解性能进行了表征. 结果表明, 该共聚物的降解速率明显增快, 材料降解2个月后, 材料的质量损失达到28.1%, 特性黏度降低近40%.     

侧链胆甾液晶聚合物及弹性体的液晶性能研究

把胆甾液晶单体 4 烯丙氧基苯甲酸胆甾醇酯 (Mch)分别和向列液晶单体 4 烯丙氧基苯甲酰氧基 4′ 甲氧基苯 (Mn) ,向列液晶交联剂 2 叔丁基对苯二酚双 [4 (6 丙烯酰氧基己氧基 )苯甲酸酯 ](Mnc)接枝到聚硅氧烷链上 ,得到系列侧链液晶聚合物Pn 系列和液晶弹性体Pe 系列 .通过热分析、偏光显微分析和X 射线分析等手段分别研究了向列液晶单体和向列液晶交联剂对含同一胆甾液晶基元聚合物的影响 .结果表明 ,向列液晶单体的摩尔百分比在 80 %以下 ,液晶聚合物Pn 系列为胆甾型液晶 ,在研究的范围内 ,液晶弹性体Pe 系列也为胆甾型液晶 ,Pn 系列和Pe 系列都具有较宽的液晶相范围 ,热分解温度均在 2 80℃以上 .     

一种248 nm光刻胶成膜树脂的合成及相关性能研究

通过自由基共聚合,制备了前驱体共聚物聚对特丁氧酰氧基苯乙烯-共-N-羟基-5-降冰片烯-2,3-二甲酰亚胺甲基丙烯酸酯,该共聚物可以通过热解而部分脱除酚羟基上的保护基,得到目标共聚物聚对羟基苯乙烯-共-N-羟基-5-降冰片烯-2,3-二甲酰亚胺甲基丙烯酸酯-共-对特丁氧酰氧基苯乙烯.通过对具有合适分子量的目标共聚物的有机溶剂溶解性、热性能、成膜性、抗干蚀刻能力和在248 nm处光学吸收(为0.212 μm^-1)性能进行研究,表明该聚合物能满足248 nm光刻胶成膜树脂的要求;此外,目标共聚物还具有酸致脱保性能.具有合适分子量和脱保率的目标共聚物,通过对其酸解留膜率的测试,推测其可能满足248 nm光刻胶的曝光显影工艺过程.     

2-丙烯酰氧基丙烯酸酯的合成及其环化聚合

本文报告2-丙烯酰氧基丙烯酸甲酯和乙醇(V_a,V_b)和2-甲基丙烯酰氧基丙烯酸乙酯(V_c)等三种1,5-二烯类单体的合成和聚合工作。 2-羟基-3-氯丙酸酯分别与3-氯丙酰氯及2-甲基-3-氯丙酰氯反应,生成相应的2-(3’-氯丙酰氧基)-3-氯丙酸甲酯和乙酯(IV_a,IV_b)和2-(2’-甲基-3’-氯丙酰氧基)-3-氯丙酸乙酯(IV_c)。IV在三乙胺的作用下,消去两分子的氯化氢而得到相应的单体(V)。V易进行聚合反应。从其溶液聚合物的溶解性能、双键分析值和红外吸收光谱,证明聚合反应主要是按环化聚合反应机理进行的,生成具有γ-内酯环型结构重复单位的聚合物。     

水溶性丙烯酸酯类感光干膜的制备及其性能研究

用溶液聚合法合成了水溶性丙烯酸树脂,并以该树脂为成膜物质制备了水溶性感光干膜。傅立叶-红外光谱和¹HNMR分析表明,丙烯酸树脂中不含CC不饱和双键,基本不参与紫外光固化反应。感光干膜性能测试表明,干膜中丙烯酸树脂的酸值及重均分子量会影响干膜的解析度和附着力等性能。进一步的研究表明,曝光能量、感光级数和显影时间也会直接影响干膜的性能。以30 μm厚度干膜Ⅱ为例,为获得较好的性能,丙烯酸树脂中甲基丙烯酸含量范围为21.5%~23.8%,重均分子量范围为6.00×10⁴~7.54×10⁴,曝光能量设定40~60 mJ/cm²,感光级数为18~23/41^ST,显影时间40~50 s,在此条件下,干膜的解析度可以达到30 μm,附着力为20 μm,干膜线路的侧边形貌和尺寸稳定性良好。此外,感光干膜中丙烯酸酯的比例和种类也会影响干膜的各方面性能,通过调节干膜中各组分含量的比例可以优化干膜性能。     

Asymmetric supercapacitors based on high capacitance Ni6MnO8 and graphene

A fast, facile and cost-effective method is used to synthesize Ni₆MnO₈ electrode with high electrochemical performance. The supercapacitor based on Ni₆MnO₈ electrode exhibits excellent stability, high area specific capacitance and promising energy and power density.     

长度可控杆状SBA-15的合成

以三嵌段共聚物P123为结构导向剂, 天然高聚物壳聚糖为添加剂, 合成出分散性较好的杆状结构SBA-15. 通过调节体系中壳聚糖的含量, 可以实现对产物形貌的控制, 即从颗粒到短杆状, 最后到长杆状. 壳聚糖的加入不仅使SBA-15的介孔结构更加长程有序, 同时也提高了其比表面积和孔容, 其最高值分别达到1157 m²/g和1.53 cm³/g.     

酸敏变色记录材料光化反应的研究

本文研究了一种由含卤共聚物和酸敏指示剂所组成的记录显示材料的光化反应,阐明了其成象过程中主要光化反应的机理,并对加入酸性添加剂,改善图象稳定性作了试验和讨论。     

基于二氧化碳共聚物的紫外光固化高分子材料的制备与性能

普通低分子量的二氧化碳共聚物由于预聚体中含有较多的亲水性端羟基, 在紫外光辐照下不能交联而降低材料的耐水性. 为降低亲水性端羟基对材料耐水性的影响, 本文利用锌钴双金属氰化物(Zn-Co DMC)催化剂实现了CO₂与4-乙烯基环氧环己烷、 环氧环己烷的三元无规共聚, 制备出分子量在40000以上, 含C=C双键的脂环族聚碳酸酯; 采用四(3-巯基丙酸)季戊四醇酯为固化剂, 基于紫外光诱导的双键-巯基点击反应制备了紫外光固化高分子材料. 研究发现, 在5.0 mJ/cm²的紫外光辐照剂量下即可制备出高透明硬化涂层, 在可见光(400~750 nm)波段内透光率达到97.5%, 铅笔硬度达到3H, 对马口铁等基体附着力达到0级. 值得指出的是, 该紫外光固化薄膜的玻璃化转变温度超过110 ℃, 与双酚A型环氧树脂相当, 而且不含苯环等结构, 具有更优异的耐紫外光老化性能.     

The importance of the plume ejection time for the fragmentation yields observed in the UV ablation of molecular van der Waals films. Ablation of chlorobenzene films at 248 nm

The efficiency of photolysis in the ablation of thick C₆H₅Cl films at 248 nm is probed over 40–300 mJ/cm² by means of time-of-flight quadrupole mass spectrometry. Up to ≈ 150 mJ/cm², the photolysis yield is considerably smaller than that in the gas-phase. We argue that because of plume ejection well after the laser pulse, photolysis occurs exclusively in the film, and as a result, permanent dissociation is limited by the operation of efficient recombination processes characteristic of condensed phases. Fragmentation starts being important only at higher fluences, at which desorption during the laser pulse is indicated to be significant.     

Synthesis and Characterization of Novel Sulfonated Polyimides from 4,6-Bis（4-aminophenoxy）-naphthalene-2-sulfonic Acid

A novel sulfonated diamine monomer, 4,6-bis（4-arninophenoxy）-naphthalene-2-sulfonic acid（BAPNS）, was synthesized. A series of sulfonated polyimide copolymers was prepared from BAPNS, 1,4,5,8-naphthalenetetracarboxylic dianhydride（NTDA） and nonsulfonated diamine 4,4＇-diaminodiphenyl ether（ODA）. Flexible, transparent, and mechanically strong membranes were obtained. The novel sulfonated polyimide（SPI） membranes show higher conductivity, for example, SPI-100 shows a conductivity of 0.0698 S/cm at 80℃（SPI-X： Xrefers to molar fraction of BAPNS）. The membranes exhibit the permeability of methanol from 2.18×10^-7 cm2/s to 2.57×10^-7 cm2/s, which is much lower than that of Nafion（2.00×10 6 cm^2/s）. The copolymers were thermally stable up to 330℃. The sulfonated polyimide copolymers also show reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 100%（molar fraction） BAPNS is 1.35 GPa under high moisture condi- tions. The optimum concentration of BAPNS was found to be 100%（molar fraction） from the view point of proton conductivity, methanol permeability, and membrane stability.     

Comparison of the Disinfection Effects of Vacuum-UV (VUV) and UV Light on Bacillus subtilis Spores in Aqueous Suspensions at 172, 222 and 254 nm

The efficacy of UV and vacuum-UV (VUV) disinfection of Bacillus subtilis spores in aqueous suspensions at wavelengths of 172, 222 and 254 nm was evaluated. A Xe₂* excilamp, a KrCl* excilamp and a low-pressure mercury lamp were used as almost monochromatic light sources at these three wavelengths. The first-order inactivation rate constants at 172, 222 and 254 nm were 0.0023, 0.122 and 0.069 cm² mJ⁻¹, respectively. Therefore, a 2 log reduction of B .  subtilis spores was reached with fluences (UV doses) of 870, 21.6 and 40.4 mJ cm⁻² at these individual wavelengths. Consequently, for the inactivation of B .  subtilis spores, VUV exposure at 172 nm is much less efficient than exposure at the other two wavelengths, while exposure at 222 nm is more efficient than that at 254 nm, which is probably because triplet energy transfer from DPA to thymine bases at 222 nm is higher than that at 254 nm. This research indicated quantitatively that VUV light is not practicable for microorganism disinfection in water and wastewater treatment. However, in comparison with other advanced oxidation processes ( e.g. UV/TiO₂, UV/H₂O₂ or O₃/H₂O₂) the VUV-initiated photolysis of water is likely more efficient in generating hydroxyl radicals and more effective for the inactivation of microorganisms.     

Pulse radiolysis study of reactions of alkyl and alkylperoxy radicals originating from methyl tert-butyl ether in the gas phase

UV spectra and kinetics for the reactions of alkyl and alkylperoxy radicals from methyl tert-butyl ether (MTBE) were studied in 1 atm of SF₆ by the pulse radiolysis-UV absorption technique. UV spectra for the radical mixtures were quantified from 215 to 340 nm. At 240 nm. σ_R = (2.6 ± 0.4) × 10⁻¹⁸ cm² molecule⁻¹ and σ_RO2 = (4.1 ± 0.6) × 10⁻¹⁸ cm² molecule⁻¹ (base e). The rate constant for the self-reaction of the alkyl radicals is (2.5 ± 1.1) × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹. The rate constants for reaction of the alkyl radicals with molecular oxygen and the alkylperoxy radicals with NO and NO₂ are (9.1 ± 1.5) × 10⁻¹³, (4.3 ± 1.6) × 10⁻¹² and (1.2 ± 0.3) × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹, respectively. The rate constants given above refer to reaction at the tert-butyl side of the molecule.     

Hierarchical TiO2 Flower-spheres with Large Surface Area and High Scattering Ability: an Excellent Candidate for High Efficiency Dye Sensitized Solar Cells

Hierarchical TiO₂ flower-spheres assembled from porous nanosheets-stacked of nanoparticles were synthesized by a simple hydrothermal method with one-step. The as-prepared TiO₂ flower-spheres showed a diameter range from 200 nm to 550 nm and a large surface area of 188 m²/g. A double layer photoanode made of P25 nanoparticles and as-prepared TiO₂ flower-spheres was fabricated for the dye sensitized solar cells(DSSCs). The efficient light scattering and dye absorption of the photoanode can be attributed to the top-layer of hierarchical TiO₂ flower-spheres. DSSCs based on the double layers photoanode exhibit a higher energy conversion efficiency of 8.11% with a short-circuit photocurrent density of 17.87 mA/cm², indicating that there is an increase of 38% in the conversion efficiency compared to those based on electrode P25(5.91%, 14.09 mA/cm²).