结构微裂纹混频非线性超声检测方法研究

给出了一种基于混频效应的非线性超声微裂纹检测方法。首先,对结构损伤混频检测机理及信号特征提取方法进行了理论分析,之后,根据试件中差频分量及和频分量幅值分布随激励信号频率变化关系,优化确定出混频检测参数。最后,进行了异侧混频激励下无损检测试验研究,并分析了激励信号频率变化对混频检测效果的影响。结果表明,异侧激励混频检测模式不仅可以实现结构中疲劳微裂纹检测,而且可以实现缺陷的定位。且检测信号频率选择对混频检测信噪比有一定的影响。当检测信号中的混频分量幅值最大时,混频检测效果最佳。因此,在优化检测参数基础上,异侧混频激励检测模式可以很好实现结构微裂纹的检测与定位。      

裂纹尖端塑性区非线性超声混频定位表征

基于非共线体波混频的方法,本文对金属材料中裂纹尖端的塑性变形区开展定位表征研究。基于二阶微扰理论和矢量分析方法,理论研究非共线体波混频的共振条件及其定位塑性变形区的机理。有限元仿真表明,两横波混频产生的纵波可用于定位塑性变形区。以A17075-T6材料为检测对象,通过实验证明两列横波混频定位裂纹尖端塑性区的可行性。实验中分别选取中心频率为5 MHz-5 MHz的两列横波和4.75 MHz-55.25 MHz的两列横波作为基波,利用非线性超声混频参量定位表征裂纹尖端的塑性变形区。研究结果表明两种频率对产生的非线性超声混频参量峰值区域与试样中塑性区位置吻合度比较好,可以看出非线性超声混频方法能够比较有效地定位金属裂纹尖端塑性区。      

基于时间反转的骨裂纹超声成像模拟研究

提出了一种结合超声非线性和时间反转技术进行长骨中裂纹成像的技术.骨裂纹的超声散射信号中包含非经典非线性成分.从时反阵列接收的探测信号中,经滤波得到三次谐波;然后利用时间反转技术来对裂纹区域进行聚焦成像.在计算机仿真实验中,基于Preisach-Mayergoyz(PM)模型模拟了单个及两个骨裂纹产生的非线性信号,实现了时间反转的非线性成像,并讨论了裂纹的深度位置对成像结果的影响.该方法为骨裂纹的超声无损检测提供了一种新技术.     

超声非线性效应表征的动态小波指纹分析方法

针对结构早期损伤超声非线性检测中损伤表征问题,发展了一种基于动态小波指纹的超声信号分析方法,从超声信号的动态小波指纹分布中提取出一种可用于结构早期损伤表征的超声非线性特征参数。研究了小波基函数及分析尺度对超声非线性效应提取效果的影响,优选出对结构早期损伤敏感的小波基函数以及尺度范围。将提出的动态小波指纹分析方法应用于二次谐波及混频非线性超声检测信号分析,结果表明,动态小波指纹分析方法可有效提取出检测信号中的二次谐波及混频分量,基于小波指纹分布的非线性特征参数可用于板结构中微裂纹的定量表征.本文研究工作为结构早期损伤超声非线性检测中的弱非线性效应提取作了有益探索。      

金属板疲劳损伤非线性兰姆波混频检测

针对金属板结构安全运行需要,开展了金属板结构疲劳损伤非线性兰姆波混频检测方法研究.通过数值仿真,研究了两列A0兰姆波与材料损伤间的非线性相互作用.结果 表明,两列共线A0兰姆波在结构材料损伤处产生单向传播的和频S0波,且和频波幅值随传播距离具有积累增长效应.对不同疲劳程度金属板试件进行了共线混频兰姆波检测实验,结果表明...     

基于幅度调制的非线性超声相控阵成像方法*

超声相控阵是超声检测领域常用的材料缺陷定位和成像技术,可便捷快速地对裂纹、孔洞等缺陷进行成像。但是,传统超声相控阵方法对较小缺陷如闭合裂纹不太敏感。非线性超声信号因对材料性能退化以及微小缺陷敏感而广受关注。本文针对疲劳闭合裂纹检测,提出一种基于幅度调制的非线性超声相控阵成像方法,通过测量物理聚焦和虚拟聚焦两种聚焦模式下超声扩散场中的声能差,并将其作为非线性参量,实现疲劳裂纹闭合部分的定位成像和定量表征。将该法应用于7075铝合金试样疲劳裂纹的实验测量,并研究了扩散场信号延迟时间对非线性超声相控阵成像结果的影响。结果表明：相较于传统超声相控阵全聚焦法,基于幅度调制的非线性超声相控阵成像方法能够更准确地定位和成像疲劳裂纹闭合部分;延迟时间的选择对疲劳裂纹长度的表征精度影响较大,本文研究了该延迟时间的选择方法并实现了检测结果的优化。     

接触缺陷的振动调制超声导波检测技术研究

针对常规线性超声检测方法无法实现板结构接触类缺陷(如微裂纹、脱粘等)检测问题,将超声导波技术与振动声调制技术相结合,利用稀疏分布传感器发展了一种板结构中接触缺陷非线性超声检测方法。通过低频振动改变缺陷的接触状况,使得通过接触面的高频导波信号的相位和幅值受到调制。对受低频振动调制的超声导波二维时间序列进行时频分析,由于接触类缺陷的存在,在振动调制超声导波序列的时频分布上出现明显的低频振动频率分量。利用提取出的低频振动频率下的超声导波信号,进行了结构接触缺陷成像处理。检测试验表明,基于振动声调制的超声导波缺陷成像方法可以实现结构中的接触类缺陷检测。      

应用混频超声检测微小缺陷

高端飞行器的可靠性往往受限于其发动机内部盘、板等构的结构强度和使用寿命,因此对这类部件的无损检测在制造业上具有巨大需求。超声检测作为一种应用广泛、高效、环保的检测方法,常常被应用于这类构件的检测中。但是,大厚度盘、板类构件内的微小缺陷反射能力弱,常规超声脉冲反射法无法进行有效检测。为实现大厚度盘、板类构件内部微小缺陷的识别和定位,采用共线异侧纵波混频法,通过和差频信号特征识别微小缺陷;研究缺陷埋深变化对混频效果的影响,通过测量和差频信号幅值变化,实现微小缺陷的深度定位。结果表明：该方法可有效识别7075铝合金中埋深80 mm的?0.2 mm横孔微缺陷,且可实现微小缺陷的深度定位。     

金属基复合结构粘接强度的非线性超声混频检测

采用非线性超声混频方法对金属基复合结构的粘接强度进行表征研究。以不同固化剂含量的铝合金丙烯酸酯粘接结构作为检测对象,基于非线性超声混频的共振条件及其作用机制,并结合粘接固化机理,开展了非线性超声混频实验。非线性超声混频模式选取两列横波生成和频纵波的方式,实验测量并计算不同基频周期数下的超声非线性参量。通过拉伸实验标定粘接结构的粘接强度,并采用扫描电镜分析拉伸断面微观结构,进而分析超声非线性参量与粘接强度的关系。从实验结果可以看出在不同周期的基频信号激励下,超声非线性参量随着粘接强度的增大均呈现出减小的趋势。研究表明非线性超声混频信号对金属基复合结构粘接强度的变化比较敏感,可以适用于类似结构件粘接强度状态弱化的表征。     

非线性电磁超声对铝合金拉伸变形评价研究

非线性系数是描述材料中微纳尺度损伤的特征参量,非线性系数常通过接触式压电超声进行检测,但耦合剂引起的非线性一般是未知的,针对这一问题,提出了一种非接触式电磁超声非线性纵波检测方法。该方法基于洛伦兹力机理在试件表面产生的振动弹性波,利用不同拉伸载荷下所制备的损伤试件,分别利用压电超声、电磁超声进行非线性超声系数测量。实验结果表明:利用两种非线性超声检测的相对非线性系数与铝合金的拉伸形变呈单调关系,同时也论证了电磁超声纵波基于非线性理论对塑性变形评估的可行性。      

基于光声信号的高铁钢轨表面缺陷检测方法

针对传统的基于超声信号的高铁钢轨无损检测方法对于表面微裂纹检测效果不佳的问题,提出了一种基于光声信号的高铁钢轨表面缺陷检测方法.首先,使用有限元及K-wave方法建立了钢轨模型并获得了模拟光声信号;然后利用时间反演的方法对钢轨表面的光声图像进行了重建,并研究了不同传感器中心频率对成像结果的影响;最后设计实验采集了钢轨表面的光声信号并进行了处理和分析.实验结果表明,基于光声信号的高铁钢轨表面缺陷检测方法对于表面微裂纹有很好的检测效果,该方法在钢轨探伤领域有较大的可行性及发展潜力.     

Nonlinear ultrasonic imaging method for closed cracks using subtraction of responses at different external loads

To improve the selectivity of closed cracks for objects other than cracks in ultrasonic imaging, we propose an extension of a novel imaging method, namely, subharmonic phased array for crack evaluation (SPACE) as well as another approach using the subtraction of responses at different external loads. By applying external static or dynamic loads to closed cracks, the contact state in the cracks varies, resulting in an intensity change of responses at cracks. In contrast, objects other than cracks are independent of external load. Therefore, only cracks can be extracted by subtracting responses at different loads. In this study, we performed fundamental experiments on a closed fatigue crack formed in an aluminum alloy compact tension (CT) specimen using the proposed method. We examined the static load dependence of SPACE images and the dynamic load dependence of linear phased array (PA) images by simulating the external loads with a servohydraulic fatigue testing machine. By subtracting the images at different external loads, we show that this method is useful in extracting only the intensity change of responses related to closed cracks, while canceling the responses of objects other than cracks.     

Numerical simulation of evaluation of surface breaking cracks by array-lasers generated narrow-band SAW

Most of the factors limiting the extensive application of laser-based ultrasonic for nondestructive evaluation of surface breaking crack are its poor sensitivity, low efficiency relative to conventional contact ultrasonic methods and limit on the dimension of the cracks. For this reason, a new technique that multiplepulse narrow-band ultrasound generated by laser arrays has been proposed. It is found that crack detection dependent on spectrum of narrow-band ultrasound generated by laser arrays can be operated with low amplitude requirements. In this paper, the narrow-band ultrasound generated by pulse laser arrays interacting with surface breaking cracks has been simulated in detail by the finite element method (FEM) according to the thermoelastic theory. The pulsed array lasers were assumed to be transient heat source, and the surface acoustic wave (SAW) which propagating on the top of the plate was computed based on thermoelastic theory. Then the frequency spectrums of both reflected waves by crack and transmission ones through crack were compared with the direct waves. Results demonstrate that multiple-frequency components of the narrow-band ultrasound were varied with change of the depth of surface breaking cracks significantly, which provides the possibility for precise evaluation of surface breaking cracks.     

All-optical probing of the nonlinear acoustics of a crack

Experiments with an all-optical method for the study of the nonlinear acoustics of cracks in solids are reported. Nonlinear acoustic waves are initiated by the absorption of radiation from a pair of laser beams intensity modulated at two different frequencies. The detection of acoustic waves at mixed frequencies, absent in the frequency spectrum of the heating lasers, by optical interferometry or deflectometry provides unambiguous evidence of the elastic nonlinearity of the crack. The high contrast in crack imaging achieved by remote optical monitoring of the nonlinear acoustic processes is due to the strong dependence of the efficiency of optoacoustic conversion on the state of the crack. The highest acoustic nonlinearity is observed in the transitional state of the crack, which is intermediate between the open and the closed ones.     

Interaction of fatigue crack with vibration and ultrasound in metallic rod and its use for quantitative characterization

According to the principle of synchronous demodulation,the modulation information in the output signal of vibro-acoustic modulation test was investigated and the nonlinear interaction of sound and vibration with the crack interface in a metallic rod was analyzed.A swept signal excitation was used to obtain a proper high frequency parameter in the test of aluminum rod samples with different sizes of cracks and the modulation information in the output signal was analyzed.It was found that the ultrasound wave in the structure can be separated into two parts.One is the wave which passes through the crack interface modulated by the low frequency vibration,and other wave has no any changes.The nonlinear modulation model was modified and a quantitative method for crack detection was proposed.It is demonstrated by comparing with the ultrasonic C-scanning that this method can be used to estimate the fatigue crack size in the metallic rod.     

铝合金板疲劳微裂纹超声红外成像检测的数值及实验研究

超声红外成像检测技术是一种发展迅速的新型无损检测技术,可用于检测材料表面或近表面的缺陷,由于对缺陷具有选择性加热的特点,近年来备受检测行业的关注。该文在铝合金板中制作疲劳微裂纹,在板中激励声波,裂纹表面因振动摩擦生热,用红外摄像仪记录板表面温度分布。拍摄的红外图像序列经傅里叶变换后得到的幅值和相位图能清晰显示裂纹的特征,测量到的裂纹长度误差达到4.3%。用有限元模拟超声在板中裂纹处的生热过程,研究板中超声在裂纹处的励热机制。超声激励时间、裂纹表面间摩擦系数和裂纹开口宽度直接影响裂纹处的励热效果,最高温度通常位于裂纹尖端附近。模拟和实验结果均表明超声红外成像检测技术能对板中疲劳微裂纹实现快速检测,提供有效、可信的检测结果。     

Nonlinear ultrasonic wave modulation for online fatigue crack detection

This study presents a fatigue crack detection technique using nonlinear ultrasonic wave modulation. Ultrasonic waves at two distinctive driving frequencies are generated and corresponding ultrasonic responses are measured using permanently installed lead zirconate titanate (PZT) transducers with a potential for continuous monitoring. Here, the input signal at the lower driving frequency is often referred to as a ‘pumping’ signal, and the higher frequency input is referred to as a ‘probing’ signal. The presence of a system nonlinearity, such as a crack formation, can provide a mechanism for nonlinear wave modulation, and create spectral sidebands around the frequency of the probing signal. A signal processing technique combining linear response subtraction (LRS) and synchronous demodulation (SD) is developed specifically to extract the crack-induced spectral sidebands. The proposed crack detection method is successfully applied to identify actual fatigue cracks grown in metallic plate and complex fitting-lug specimens. Finally, the effect of pumping and probing frequencies on the amplitude of the first spectral sideband is investigated using the first sideband spectrogram (FSS) obtained by sweeping both pumping and probing signals over specified frequency ranges.     

An ultrasonic method for dynamic monitoring of fatigue crack initiation and growth

Attached ultrasonic sensors can detect changes caused by crack initiation and growth if the wave path is directed through the area of critical crack formation. Dynamics of cracks opening and closing under load cause nonlinear modulation of received ultrasonic signals, enabling small cracks to be detected by stationary sensors. A methodology is presented based upon the behavior of ultrasonic signals versus applied load to detect and monitor formation and growth of cracks originating from fastener holes. Shear wave angle beam transducers operating in through transmission mode are mounted on either side of the hole such that the transmitted wave travels through the area of expected cracking. Time shift is linear with respect to load, and is well explained by path changes due to strain combined with wave speed changes due to acoustoelasticity. During subsequent in situ monitoring with unknown loads, the measured time of flight is used to estimate the load, and behavior of the received energy as a function of load is the basis for crack detection. Results are presented from low cycle fatigue tests of several aluminum specimens and illustrate the efficacy of the method in both determining the applied load and monitoring crack initiation and growth.     

Thermo-optical modulation of ultrasonic surface waves for NDE

The well-known thermo-elastic effect of laser irradiation can be exploited to produce strong localized stresses when an expanded, long pulse, low-intensity laser beam is used to irradiate the specimen. These stresses will produce a parametric modulation of the received ultrasonic signals, that is somewhat similar to the acousto-elastic effect often used in nonlinear ultrasonic studies. It is shown in this paper that otherwise hidden small cracks in fatigue-damaged aluminum and titanium specimens can be readily detected by exploiting this optically induced thermo-elastic modulation during ultrasonic surface wave inspection since they are susceptible to crack closure and therefore exhibit strong parametric modulation. The temporal and spatial variations of the ultrasonic signals due to laser irradiation were evaluated numerically and experimentally. Based on these results, the direct temperature modulation of the ultrasonic velocity can be separated from the thermo-elastic stress modulation present only in cracked specimens. It was found that this method can be used to selectively increase the sensitivity of ultrasonic flaw detection to small fatigue cracks by more than one order of magnitude.