纳米二氧化钛富集-分光光度法测定水体中痕量5-磺基水杨酸

采用纳米TiO2化学吸附法富集水样中痕量5-磺基水杨酸。5-磺基水杨酸含有酚羟基(OH)和羧基(COOH)可与TiO2表面上的羟基(OH)发生酯化反应,形成稳定的六元环结构。纳米TiO2对5-磺基水杨酸的吸附量≤18.47mg/g,在pH2.5、吸附时间20min、吸附剂用量1.80g/L的条件下,纳米TiO2对试样中5-磺基水杨酸的吸附率达到99.0%,以5mL2mol/L NaOH为洗脱液,洗脱率达99.8%,对试样中5-磺基水杨酸的富集倍数达50倍,检出限(3σ,n=11)为26.7μg/L。本法操作简便,直接用于九龙江和海水中痕量5-磺基水杨酸的测定,结果准确,回收率达到95.5%～98.5%。     

甲壳素色谱柱富集—快速吸光光度法测定环境试样中痕…

研究了甲壳素色谱柱富集Ｆｅ（Ⅲ）－磺基水杨酸－十八烷基十甲基氨基乙酸的红紫色缔合物，用磺基水杨酸洗脱后，在分光光度计上直接测定洗脱液的吸光度，方法快速，简单、富集倍数高，用于环境水样中痕量铁的测定，结果令人满意。     

鲁米诺-高锰酸钾体系化学发光法测定5-磺基水杨酸

基于碱性介质中5-磺基水杨酸对鲁米诺-KMnO4体系化学发光的增强作用,建立了流动注射化学发光法测定5-磺基水杨酸的新方法。最佳实验条件下,测定5-磺基水杨酸的线性范围为5.0×10-6~8.0×10-4mol/L,线性相关系数为0.9994(n=8),检出限为3.8×10-6mol/L(n=11),对5.0×10-5mol/L的5-磺基水杨酸进行测定,其相对标准偏差为1.4%(n=11)。方法应用于强力霉素废水中5-磺基水杨酸的测定。     

Luminol-H2O2-纳米银化学发光体系测定5-磺基水杨酸

碱性条件下,5-磺基水杨酸对Luminol-H2O2-纳米银化学发光体系有较强的增敏作用,据此,结合流动注射技术,建立了测定5-磺基水杨酸的新方法。在最佳实验条件下,5-磺基水杨酸浓度在1.5×10-8～2.0×10-6mol/L范围内与相对发光强度呈线性关系,检出限(3σ)为1.0×10-9mol/L。对4.0×10-7mol/L的5-磺基水杨酸平行测定9次,相对标准偏差为2.7%。该法用于强力霉素废水中5-磺基水杨酸的测定,结果令人满意。     

KMnO4-乙二醛化学发光体系测定5-磺基水杨酸的流动注射分析

酸性介质下,KMnO4可以氧化5-磺基水杨酸产生化学发光,乙二醛对该体系有增敏作用。结合流动注射技术,建立了测定5-磺基水杨酸的流动注射化学发光方法。方法线性范围为2.0×10-8～2.0×10-5mol/L,检出限为2.0×10-9mol/L,对2.0×10-6 mol/L的5-磺基水杨酸平行测定11次,相对标准偏差为1.9%。该法可用于强力霉素废水中5-磺基水杨酸的测定。     

N-溴代琥珀酰亚胺-二氯荧光素化学发光体系测定废水中5-磺基水杨酸

建立了测定5-磺基水杨酸的流动注射化学发光新方法。 研究了影响化学发光强度的因素,并初步探讨了可能的发光机理。 在最佳化学发光条件下,化学发光强度与5-磺基水杨酸浓度在5.0×10-8~2.0×10-5 mol/L范围内呈良好的线性关系,检出限为1.0×10-8 mol/L,对5.0×10-6 mol/L的5-磺基水杨酸平行测定9次,其相对标准偏差为2.7%。 该法可用于强力霉素废水中5-磺基水杨酸的测定。     

鲁米诺-焦性没食子酸体系抑制化学发光法测定5-磺基水杨酸

基于碱性介质中5-磺基水杨酸对鲁米诺-焦性没食子酸体系化学发光的抑制作用,建立了流动注射化学发光测定5-磺基水杨酸的新方法.在最佳实验条件下,测定5-磺基水杨酸的线性范围为1.0×10-7～1.0×10-5mol/L,相关系数为0.9996(n=5),检出限为6.8×10-8mol/,L(n=11),对1.0×10-6...     

EDTA滴定法测定FeO42-

利用了FeO42-在酸性条件下的有关反应,以磺基水杨酸为指示剂,建立了用EDTA间接滴定FeO42-的新方法。用于高铁酸盐的制备和使用过程中测定,测定结果与邻菲口罗啉法一致。     

聚磺基水杨酸/碳纳米管修饰电极在抗坏血酸共存时测定多巴胺

研究了聚磺基水杨酸/多壁碳纳米管修饰玻碳电极的制备及多巴胺在此修饰电极上的电化学行为, 讨论了修饰条件、扫速、溶液 pH 以及抗坏血酸的干扰对多巴胺在这种复合物电极上响应的影响. 在 pH 7.4 磷酸盐缓冲溶液中, 在1.0×10-3 mol/L 抗坏血酸共存的条件下, 多巴胺氧化峰电流与其浓度在 5×10-7～10-4 mol/L 范围内分段呈线性关系, 检出限为 1.0×10-7 mol/L. 结果表明: 聚磺基水杨酸/多壁碳纳米管修饰电极结合了多壁碳纳米管灵敏度高和聚磺基水杨酸选择性好的优点, 可用于抗坏血酸共存条件下多巴胺的测定.     

Fe(Ш)-磺基水杨酸褪色光度法测定甲巯咪唑

建立了Fe(Ш)-磺基水杨酸褪色光度法测定甲巯咪唑的方法。结果表明,在酸性介质中,甲巯咪唑分子中的巯基(-SH)可将Fe3+还原为Fe2+,采用磺基水杨酸作为Fe3+的显色剂,借褪色分光光度法间接测定了甲巯咪唑含量。显色体系最大吸收波长为480nm,甲巯咪唑质量浓度在0.072～0.156 mg/mL范围内与吸光度A呈良好的线性关系,线性回归方程为A=-0.1548ρ+0.0949,线性相关系数r=0.9988。方法用于实际药品中甲巯咪唑的含量测定,结果与药典法一致。     

An ion-exchange method for selective separation of palladium, platinum and rhodium from solutions obtained by leaching automotive catalytic converters

An ion-exchange method has been developed for the separation of palladium, platinum and rhodium from a solution that is highly acidic and contains a considerable amount of lead, aluminum, iron and cerium, obtained by leaching a used honeycomb type automotive catalytic converter. A column of Amberlite IRA-93 anion-exchange resin was found appropriate to recover platinum metals from the pregnant solution. Selective stripping of these metals from the resin was achieved by eluting rhodium first with 6.0M hydrochloric acid, then palladium with a 1% ammonia solution at ambient temperature, and platinum with 5% of the reagent at elevated temperatures. Optimum conditions for leaching these metals from the catalyst were 5.0M hydrochloric acid and 0.4M sodium chlorate at 70 degrees C. This method can be applied to both analytical as well as large scale operations. It is simple, economical, and relatively safe for human exposure and the environment.     

单柱离子色谱法测定一价阳离子的流动相研究

对单柱离子色谱法测定一价阳离子的流动相进行了系统研究，阐述了一价阳离子的保留行为和电导检测行为与流动相之间的关系，分别对无机酸（硝酸）、有机酸（柠檬酸）和芳香碱（苯胺）为流动相测定一价阳离子进行了讨论，其中有机酸和无机酸是较为适宜的流动相。     

Column chromatographic pre-concentration of iron(III) in alloys and biological samples with 1-nitroso-2-naphthol-3,6-disulphonate and benzyldimethyltetradecylammonium-perchlorate adsorbent supported on naphthalene using atomic absorption spectrometry

The solid ion-pair material produced from the reaction between benzyldimethyltetradecylammonium chloride (BDTA) and sodium perchlorate on naphthalene provides the basis for a simple, rapid and selective technique for pre-concentrating iron from up to 500 ml of aqueous solution. Iron reacts with disodium 1-nitroso-2-naphthol-3,6-disulphonate (Nitroso-R salt) to form a water-soluble coloured chelate anion. The iron chelate anion forms a water-insoluble, stable iron-Nitroso-R-BDTA complex on naphthalene packed in a column. Trace amounts of iron are quantitatively retained on naphthalene in the pH range 3.5-7.5 and at a flow-rate of 1-2 ml min-1. The solid mass is dissolved out from the column with 5 ml of N,N-dimethylformamide and iron is determined by means of an atomic absorption spectrometer at 248 nm. The calibration graph is linear for concentrations of iron over the range of 0.5-20 micrograms in 5 ml of final solution. The standard deviation and relative standard deviation were calculated. The detection limit of the method was 0.0196 micrograms ml-1 of iron. The sensitivity for 1% absorption was 0.072 microgram ml-1 (0.165 microgram ml-1 by direct atomic absorption spectrometry of aqueous solution). The proposed method was applied to the determination of iron in standard alloys and biological samples.     

Preconcentration of iron (III), cobalt (II) and copper (II) nitroso-R complexes on tetradecyldimethylbenzylammonium iodide-naphthalene adsorbent

Iron, cobalt and copper form coloured water soluble anionic complexes with disodium 1-nitroso-2-naphthol-3-6-disulphonate (nitroso R-salt). The anionic complex is retained quantitatively as a water insoluble neutral ion associated complex (M-nitroso R-TDBA) on tetradecyldimethylbenzylammonium iodide on naphthalene (TDBA(+)I(-)-naphthalene) packed column in the pH range of: Fe(III): 3.1-6.5, Co: 3.4-8.5 and Cu 5.9-8.0 when their solutions are passed individually over this adsorbent at a flow rate of 0.5-5.0 ml/min. The solid mass consisting of an ion associated metal complex along with naphthalene is dissolved out of the column with 5 ml dimethylformamide/chloroform and metals are determined spectrophotometrically. The absorbance is measured at 710 nm for iron, 425 nm for cobalt and 480 nm for copper. Beers law is obeyed in the concentration range 9.2-82 mug of iron, 425 nm for cobalt cobalt and 3.0-62 mug of copper in 5 ml of final DMF/CHCl(3) solution. The molar absorptivities are calculated to be Fe: 7.58 x 10(3), Co: 1.33 x 10(4) and Cu: 4.92 x 10(4)M(-1)cm(-1). Ten replicate determinations containing 25 mug of iron, 9.96 mug of cobalt and 3.17 mug of copper gave mean absorbances 0.677, 0.450 and 0.490 with relative standard deviations of 0.88, 0.98 and 0.92%, respectively. The interference of large number of metals and anions on the estimations of these metals has been studied. The optimized conditions so developed have been employed for the trace determination of these metals in standard alloys, waste water and fly ash samples.     

Selective separation of99Mo from fission products in chloride media on activated alumina

The radioisotope⁹⁹Mo generated through the fission of neutron-irradiated uranium targets was separated in an extremely radiochemically pure state. The target dissolution mixture was run on a silica gel column whereby the⁹⁵Zr−⁹⁵Nb activity, the serious radiocontaminants of⁹⁹Mo, was adsorbed on the gel. The effluent from the gel column was processed and treated with sodium dihydrogen phosphate. The processed solution was run on an activated alumina column whereby⁹⁹Mo was adsorbed as phospho-molybdate complex ion, then desorbed from the column as the molybdate ion by eluting with 10% NaOH solution. By recycling the adsorption and desorption steps on alumnia,⁹⁹Mo was finally obtained totally free from all other radiocontaminants.     

过渡金属乙酰丙酮螯合物的体积排除色谱研究

用体积排除色谱方法研究了过渡金属Fe(Ⅲ)、Co(Ⅲ)、Cu(Ⅱ)、Ni(Ⅱ)的乙酰丙酮螯合物在四氢呋喃溶液中的加合和缔合行为。在溶液中乙酰丙酮钴(Ⅲ)以单个螯合物分子的形式存在,乙酰丙酮铜(Ⅱ)和乙酰丙酮铁(Ⅲ)与溶剂加合生成加合物,乙酰丙酮铁(Ⅲ)除加合物外还存在缔合度为2-10的多分散缔合物,乙酰丙酮镍(Ⅱ)水合物在四氢呋喃中产生了加合交换作用,同时存在缔合度为6左右的缔合物。色谱数据给出了螯合物、加合物及缔合物的相对含量。螯合物与相同分子量的聚苯乙烯相比,其保留体积的滞后以Ni相似文献   

Improved separation of cadmium from indium,zinc, gallium and other elements by anion-exchange chromatography in hydrobromic nitric acid mixtures

The separation of cadmium from indium, zinc and many other elements is considerably improved by eluting these elements with 0.1 M hydrobromic–0.5 M nitric acid solution from a column of AG1-X8 resin. Cadmium is retained very strongly and can be eluted with 2 M nitric acid or 1 M ammonia–0.2 M ammonium nitrate solution. Separations are sharp and quantitative and from microgram amounts up to 2 g of indium and zinc are separated from amounts of cadmium ranging from micrograms up to 100 mg on a 2-g (4.6 ml) resin column. Ga(II), Fe(III). Mn(II), Co(II), U(VI) and Ni(II) can be separated quantitatively from cadmium in the same way. The behaviour of numerous elements is discussed, with special attention to lead, and relevant elution curves and results from the analysis of synthetic mixtures are presented.     

Improved separation of iron from copper and other elements by anion-exchange chromatography on a 4% cross-linked resin with high concentrations of hydrochloric acid

Iron(III) can be separated from copper(II) and many other elements by eluting these from a column of AG1-X4 anion-exchange resin with 8M hydrochloric acid, while iron(III) is retained and can be eluted with 0.1M hydrochloric acid. The separation is much better than the customary one with 3.5M hydrochloric acid. Columns containing only 8.8 ml (3 g) of resin can separate traces or up to more than 1 mmole of iron(III) from more than 1 g of copper. Mn(II), Ni, Al, Mg and Ca are quantitatively eluted together with copper(II). Lead, the alkali metals, Be, Sr, Ba, Ra, Sc, Y and the lanthanides, Ti(IV), Zr, Hf, Th and Cr(III) have not been investigated in detail but should be separated according to their known distribution coefficients. Separations are sharp and quantitative, less than 1 mug of copper remaining in the iron fraction when more than 1 g was present originally. Relevant elution curves and results of the quantitative analysis of synthetic mixtures are presented.     

Indirect determination of trace amounts of fluoride in natural waters by ion chromatography: a comparison of on-line post-column fluorimetry and ICP-MS detectors

An alternative method for the determination of trace levels of fluoride in drinking and sea-water samples is presented. It is based on the formation of the aluminium monofluoride complex in excess of Al3+ and separation of the two species formed (AlF2+ and Al3+) in a small (5 cm long, CG2) ion exchange guard column. The final determination is accomplished by both ICP-MS specific detection and post column derivatisation with fluorimetric detection. Fundamental studies on the formation kinetics of the complex, ion chromatographic separation and optimum aluminium concentration were carried out using spectrofluorimetric detection by post-column reaction of the species with 8-hydroxyquinoline-5-sulfonic acid in a micellar medium of cetyltrimethylammonium bromide. Fluorimetric detection showed good detection limits, but interferences from cations such as Mg2+ and Zn2+ required the use of the longer CS2 ion exchange column. Iron interfered in relatively large amounts but adding EDTA to the sample solution eliminated the interference. A similar separation methodology was applied using ICP-MS detection for the indirect determination of fluoride, by monitoring aluminium at mass 27. In this case, a detection limit of 0.1 ng ml-1 was obtained using 0.45 M HNO3 as eluent and no interference caused by high concentrations of iron was observed. The proposed method was applied to the determination of very low levels of fluoride in natural waters.     

Extractive spectrophotometric determination of trace amounts of iron(III) with benzyltriethylammonium chloride

The ion-association complex formed between a thiocyanato-iron(III) ion and a benzyltriethylammonium ion is extracted into 1,2-dichloroethane, and its absorbance at 476 nm is used for determination of the iron. Beer's law is obeyed up to about 4 mug/ml iron concentration in the final solution. The molar absorptivity is 2.79 x 10(4) l.mole(-1).cm(-1).