影响St-MMA-MA无皂乳液胶粒性质的因素丙烯酸浓度及加料方式的影响

以苯乙烯、甲基丙烯酸甲酯为主单体,丙烯酸为功能单体合成了三元无皂乳液共聚胶粒。用ＴＥＭ观测了胶粒形态、大小及其分布;以电导滴定法测定了胶粒表面－ＣＯＯＨ的密度。考察了不同的聚合阶段加入不同量的丙烯酸对所得胶粒形态、大小及其表面－ＣＯＯＨ的密度的影响。结果表明：在聚合前加入丙烯酸,随着丙烯酸浓度的增大,胶粒粒径减小、分散系数增大;在成核后期滴加丙烯酸,胶粒粒径较大且随丙烯酸浓度增大粒径变化不大而分散     

间规聚苯乙烯的非等温结晶及其动力学

以Ｓｔ－ＭＭＡ－ＡＡ三元无皂共聚胶粒作载体,用物理吸附和共价偶联两方法固载日本血吸虫虫卵可溶性抗原（Ｓｊ－ＳＥＡ）。探讨了胶粒性质对Ｓｊ－ＳＥＡ固载量及活性的影响,研究结果表明,胶粒表面疏水性强或胶乳表面张力大,则物理吸附量大,但致敏胶乳的效价并不一定高;胶粒表面羧基密度大,共价偶联量多,但共价偶联量太大时,致敏乳效价低;在共价偶联量较小时,致敏胶乳的效价随固载的Ｓｉ－ＳＥＡ密度增大而提高。     

种子乳液聚合法制备多孔乳胶粒

用批量乳液聚合法制备了苯乙烯（Ｓｔ）———甲基丙烯酸甲酯（ＭＭＡ）二元共聚种子乳液Ｓ１以及Ｓｔ ＭＭＡ 丙烯酸（ＡＡ）三元共聚种子乳液Ｓ２,通过连续法无皂种子乳液聚合合成了一系列不同ＡＡ或ＭＡＡ（甲基丙烯酸）含量的Ｓｔ、ＭＭＡ三元共聚乳液．将所得复合胶乳进行碱／酸分步处理,得到具有多孔结构的乳胶粒．用透射电镜对胶粒形态进行了表征,考察了不饱和酸种类和用量、碱处理初始ｐＨ值及溶胀剂对胶粒成孔的影响．     

微波辐照制备多孔乳胶粒

在微波辐照的条件下，通过间歇无皂种子乳液聚合，制得聚[苯乙烯－甲基丙烯酸甲酯－丙烯酸]复合乳液。将所得复合胶乳进行碱／酸分段处理，得到具有多孔结构的乳胶粒。用透射电镜对胶粒形态进行了表征，研究了不饱和酸用量、碱处理初始pH值及碱处理时间对胶粒成孔的影响。     

MMA-BA无皂乳液共聚合(Ⅰ)

在甲基丙烯酸甲酯(MMA)和丙烯酸丁酯(BA)的无皂乳液聚合体系中,加入少量反应性乳化剂ω-十一烯酸钠(SUA),用粒度分布仪、透射电子显微镜表征了胶粒平均直径、浓度及形态,用离子交换-电导滴定分析了胶粒表面性质。     

P(MMA-EA-AA)共聚物组成对无皂乳胶粒碱处理后结构形态的影响——异型结构粒子的形成

采用批量法无皂乳液聚合技术合成了粒径窄分布的甲基丙烯酸甲酯(MMA) - 丙烯酸乙酯(EA)- 丙烯酸(AA)三元共聚物胶乳,并通过碱后处理,制备出了具有异型结构的乳胶粒,探讨了AA用量及MMA /EA质量比对胶粒结构形态的影响.结果表明,当AA含量大于0 .0 4mol时,胶乳中开始出现异型结构粒子,随着AA用量的增加和MMA/EA质量比的减小,异型粒子在胶乳中所占比例增加,胶粒体积先增大后减小.当EA用量较高时,粒子边界模糊,异型结构不明显.     

高羧基含量无皂多孔聚合物乳胶粒的研究

功能性聚合物乳液的性能与其功能基的含量密切相关. 采用完全无皂种子乳液聚合技术合成了具有不同羧基含量并且粒径分布均一的交联型聚甲基丙烯酸甲酯-丙烯酸乙酯因为甲基丙烯酸 [P(MMA-EA-MAA)]乳胶粒, 然后通过碱后处理, 制备出了高羧基含量的无皂多孔P(MMA-EA-MAA)乳胶粒. 系统研究了MAA对聚合反应、胶粒特性及胶粒多孔结构形态的影响. 结果表明: 在交联剂二乙烯基苯用量一定(0.3 g)的条件下, 随着MAA用量从4.0 mol%增加到 10.0 mol%, 聚合物交联程度(P_x)从28.26%迅速增大至90.95%, 当其用量超过10.0 mol%后P_x增大趋势变缓; 随着MAA用量的增加, 处理后胶粒体积膨胀百分率(ΔV)逐渐增大, 在MAA用量为12.0 mol%时ΔV达到42.1%的最大值, 当MAA用量增大到14.0 mol%时, 尽管P_x高达95.44%, 胶粒仍具有完好的孔状结构.     

无皂乳液聚合制备高浓度单分散聚(苯乙烯-甲基丙烯酸甲酯)胶体粒子

通过添加聚乙烯醇和丙酮，找到了一种无皂乳液聚合制备高浓度单分散苯乙烯－甲基丙烯酸甲酯共聚胶体粒子的新途径，粒子半径达纳米数量级，体系的固含量大于50％，研究了聚乙烯醇和丙酮对反应过程，胶乳粒子大小的影响，结果表明聚乙烯醇和丙酮对高浓度无皂纳米胶乳粒子的形成与稳定起重要作用。     

超声无皂乳液聚合制备BA/St/AM三元共聚物乳胶粒及其聚合机理研究

将超声技术引入到无皂乳液聚合方法中,在不加入任何引发剂和乳化剂的情况下,制备了丙烯酸丁酯(BA)/苯乙烯(St)/丙烯酰胺(AM)三元共聚纳米乳胶粒.研究了不同超声时间对单体转化率、乳胶粒粒径以及乳液粘度的影响.同时还探讨了超声无皂乳液聚合机理,认为AM在聚合过程中起到了引发和稳定的作用.TEM照片表明,乳胶粒直径大约在80nm左右,FTIR及DSC分析表明产物为三元共聚物,而不是共混物.     

不同尺寸（0.02—0.5μm）单分散聚苯乙烯乳液微球的制备

通过对苯乙烯乳液聚合微观动力学以及聚合过程中胶粒直径及其分布随时间变化的理论分析,并通过实验验证,比较了不同乳化剂种类、不同反应温度和不同单体用量条件下,产物胶乳的粒径分布,发现乳液聚合最终产物的粒径分布与成核期长短没有直接联系,而是取决于自由基进入胶粒的速率常数、稳态增长时间、胶粒中的平均自由基数目和胶粒的体积增长速率,胶乳单分散性随这些参量的增大而提高,从而解释了采用高温、高引发剂浓度以及长时间反应的条件对最终的胶粒尺寸分布的影响。本文还通过实验,找到了在20～500nm范围内控制粒径大小及粒径分布的方法。在20～100nm的范围内,用一步法乳液聚合,通过改变单体用量和乳化剂浓度,制备了一系列粒径的单分散聚苯乙烯胶乳;在100～500nm的范围内,运用种子乳液聚合,通过改变溶胀单体与种子胶乳的用量比,也制得了不同粒径的单分散聚苯乙烯胶乳。     

复合微乳液聚合制备P(MMA-UA)纳米乳胶粒子的研究

将聚氨酯预聚体可聚合乳化剂 (APUA)和甲基丙烯酸甲酯 (MMA)的复合微乳液体系 ,分别用水溶性过硫酸钾 (K2 S2 O8)和油溶性偶氮二异丁腈 (AIBN)作引发剂 ,进行微乳液聚合研究 ,制备了P(MMA UA)复合纳米乳胶粒子 .研究了APUA用量、聚合温度对聚合动力学的影响 ;用透射电子显微镜 (TEM)观察了不同乳化剂浓度及引发剂体系对胶粒形态、大小及分布的影响 .结果表明 ,用可聚合乳化剂APUA可制得稳定性很好的P(MMA UA)纳米级核 壳型乳胶粒子 ,乳胶粒径在 5 0nm左右 .随着乳化剂用量增加 ,粒子变小 ;不同类型的引发剂对胶乳的性质有较大影响 ,以APUA为乳化剂 ,K2 S2 O8为引发剂 ,在聚合反应过程中或在聚合反应后的放置中 ,会出现P(MMA UA)的纳米水凝胶 (Nanogel)现象 .     

Formation of highly monodispersed emulsifier-free cationic poly(methylstyrene) latex particles

Highly monodispersed emulsifier-free poly(methylstyrene) (PMS) latex particles were prepared via an emulsifier-free emulsion polymerization in the presence of 2,2′-azobis-(2-amidineopropane) dihydrochloride (V-50) as an initiator. A combination of kinetics and molecular weight distribution studies revealed that the polymerization followed the micellization nucleation mechanism. Results showed that an appropriate initiator concentration was necessary to obtain monodisperse and stable latex particles. Conversion of methylstyrene was found to increase significantly with increasing initiator concentrations. However, the size of PMS latex particles decreased with both the increase of initiator concentration and the reaction temperature at a constant ionic strength. The particle size was increased as the ionic strength of the aqueous phase increased, yet the variation of ionic strength had little effect on the particle size distribution. SEM micrographs showed that an agitation rate of 350 rpm or higher was required in order to produce highly monodispersed poly(methylstyrene) latex particles. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 2069–2074, 1999     

聚合物纳米微粒静电组装行为及其表征

使用2,2′-偶氮二异丁基脒二盐酸盐自由基引发剂,改变甲基丙烯酰氧乙基十六烷基二甲基溴化铵阳离子功能单体的量与苯乙烯进行乳液聚合获得不同粒径的阳离子乳胶粒,使用十二烷基硫酸钠为乳化剂和过硫酸钾为引发剂制备阴离子聚合物乳胶粒.采用基于静电相互作用的异凝聚法将以上2种带有相反电荷的乳胶粒组装,获得了表面粗糙程度不同的复合微粒.对异凝聚过程中复合液透光率和微粒大小及分布进行跟踪测试,并用透射电子显微镜表征了阳离子微粒、阴离子微粒以及复合微粒的形态和大小.结果表明,在一定范围内可以通过控制阴离子乳胶粒与阳离子乳胶粒的复合比例改变单个复合微粒表面阳离子小微粒的数目.     

苯乙烯和N-乙烯基吡咯烷酮共聚物/Ag复合微球的制备及性能研究

首先用无皂乳液聚合法制备了单分散聚苯乙烯(PSt)乳液,以此为种子乳液,使用N,N-亚甲基双丙烯酰胺(MBA)为交联剂,过硫酸钾(KPS)为引发剂,进行苯乙烯和N-乙烯基吡咯烷酮(NVP)共聚合制备了以PSt为核、St和NVP共聚物为壳的具有核-壳结构的聚合物微球(P(St-NVP)).以此微球为模板通过化学沉积法得到了粒径分布均匀、单分散的P(St-NVP)/Ag复合微球.傅里叶红外光谱、X-射线衍射、扫描电镜、透射电镜、激光粒度仪和紫外-可见光谱对复合微球的结构、形貌、物相及催化性能进行了表征.结果表明,P(St-NVP)/Ag复合微球具有规则的球形结构,粒径在400～700 nm之间,随交联剂浓度或种子乳液浓度的增加,复合微球粒径减小.粒径在十几个纳米左右的银粒子均匀分布在微球表面和内部.载银复合微球在NaBH4还原4-硝基苯酚为4-氨基苯酚的模型反应中表现出较高的催化活性.     

交联剂对无皂P(MMA-EA-MAA)种子聚合乳胶粒成孔的影响

采用完全无皂种子乳液聚合技术合成了粒径窄分布的P(MMA-EA-MAA)乳胶粒,通过对上述胶乳进行碱处理,制备出了具有空腔结构和多孔结构的聚合物乳胶粒,研究了交联剂的种类和用量对聚合过程、胶粒特性及胶粒结构形态的影响.结果表明,体系中加入交联剂后,单体转化率都有不同程度的提高;随交联剂用量的增加,乳胶粒粒径略有减小,交联剂用量较高时,乳胶粒粒径分布加宽;二乙烯基苯(DVB)的交联效率稍高于双甲基丙烯酸乙二醇酯(EGDMA);不加入交联剂及EGDMA用量低于0.5%时,处理后乳胶粒呈空腔结构,加入DVB及EGDMA用量高于1.0%时,处理后乳胶粒呈多孔结构,并且乳胶粒体积增量随交联剂用量的增加而减小.     

Some aspects of polymer colloids I. Preparation and properties of different types of latex particles

The boundary region separating a latex particle from the surrounding medium has a great influence on the properties of latex dispersions. Four types of polystyrene and polystyrene/comonomer latices differing greatly in the structure of the boundary region were prepared. The first part of a series of papers reports on the preparation of the various latex dispersions. Mean particle sizes were obtained from simple turbidity measurements, quasi-elastic light scattering, and electron micrographs. The behavior of the particles in the centrifugal force field is a simple tool for detecting aggregation tendencies that are not directly related to salt stability. The BET-surface area agrees with the area calculated from the mean particle size when a sharp boundary and smooth surface is developed between the particle and the surrounding medium. In the case of particles with extended boundary regions (core/shell particles or particles with hairy envelopes), film formation reduces the specific surface area. Removal of soluble oligomers and polymers from the boundary region during subsequent treatments (purification and centrifugation before freeze-drying) can increase the surface area considerably.     

Ion exchange in carboxylated latices — AUC studies using sedimentation and density gradient techniques

Crosslinked highly carboxylated acrylic latices with narrow particle size distributions were prepared by emulsion polymerization and characterized carefully by different AUC techniques (particle size distributions and particle density measurements). The acid form of those latices was neutralized with metal oxides like MgO, CaO, ZnO, or PbO in order to obtain the corresponding salt form of the latices which again were characterized carefully. The kinetics of the ion exchange between latex particles were studied by mixing, for example, the acid and the salt form of the latices monitoring the density distribution of the latex particles by density gradient ultracentrifugation. With all latices the hydrogen-metal ion exchange tends to be a complete one provided this process is given a sufficiently long exchange time. Theoretical models are provided which yield a qualitative explanation of the experimental data.     

Preparation of sulphonate-containing core/shell latex particles via seeded emulsion copolymerization

<正>In this study,P(St-MAA) seed latex particles were first prepared via soap-free emulsion polymerization of styrene(St) and methacrylic acid(MAA),then the seed particles were allowed to swell with St at room temperature,and the P(St-MAA)/P(StNaSS) core/shell latex particles were then synthesized via seeded emulsion copolymerization of St and sodium styrene sulphonate (NaSS) using AIBN as initiator in the presence of N,N'-methylenebisacrylamide(BAA,water-soluble crosslinker).Results showed that the polymerization could be carried out smoothly when the ratio of BAA to total monomers was less than 3 mol%,the narrow dispersed P(St-MAA) seed particles with the diameter of 150 nm and the P(St-MAA)/P(St-NaSS) core/shell latexes with the particle size of about 200 nm were synthesized.When the 25/75 mole ratio of NaSS/(St + MAA) and 2 mol%of BAA were used in the seeded emulsion polymerization,the resulted P(St-MAA)/P(St-NaSS) latex product showed a low weight loss after water extraction,and the NaSS unit content in the whole particle and in the shell reached 11.7 mol%and 34.6 mol%,respectively.     

乳液聚合法制备P(St/BA)-KAl(OH)2CO3纳米复合物

利用乳液聚合法制备了一种含KAl(OH)2CO3纳米粒子的聚苯乙烯／丙烯酸丁酯复合物．Zeta电位、粒径分布、扫描电镜(SEM)和透射电镜(TEM)等分析表明KAl(OH)2CO3粒子能够稳定地分散于苯丙乳液的乳胶粒中,形成核一壳结构．热失重(TG)分析表明KAl(OH)2CO3粒子的加入能提高复合物的热稳定性,使其在阻燃涂料领域有着潜在的应用前景．     

Synthesis of polystyrene/poly[2-(dimethylamino)ethyl methacrylate-stat-ethylene glycol dimethacrylate] core-shell latex particles by seeded emulsion polymerization and their application as stimulus-responsive particulate emulsifiers for oil-in-water emulsions

Surfactant-stabilized polystyrene (PS) latex particles with a mean hydrodynamic diameter of 155 nm were prepared by aqueous emulsion polymerization using 2,2'-azobis(2-amidinopropane) hydrochloride as a cationic radical initiator. Seeded aqueous emulsion copolymerizations of 2-(dimethylamino)ethyl methacrylate (DMA) and ethylene glycol dimethacrylate (EGDMA) were conducted in the presence of these PS particles to produce two batches of colloidally stable core-shell latex particles, in which the shell comprised a cross-linked P(DMA-stat-EGDMA) overlayer. Both the PS and PS/P(DMA-stat-EGDMA) latexes were characterized in terms of their particle size, morphology, and composition using dynamic light scattering, electron microscopy, and FT-IR spectroscopy, respectively. Using the PS/P(DMA-stat-EGDMA) latex particles as a pH-responsive particulate ('Pickering'-type) emulsifier, polydisperse n-dodecane-in-water emulsions were prepared at pH 8 that could be partially broken (demulsified) on lowering the solution pH to 3. These emulsions were characterized in terms of their emulsion type, mean droplet diameter, and morphology using electrical conductivity and Mastersizer measurements, optical microscopy, and scanning electron microscopy (using critical point drying for sample preparation).