混合溶剂系统中固定化脂肪酶对酮基布洛芬的催化酯化反应

以硅藻土吸附的脂肪酶为催化剂,对外消旋酮基布洛芬[2-(3-苯甲酰苯基)丙酸]进行对映选择性酯化反应;考察了不同的脂肪酶制剂,固定化时所加缓冲液的体积与pH值,酰基受体(醇)的种类以及混合溶剂系统的组成等因素对酶活性的影响.结果表明,在所考察的7种脂肪酶中,以LipaseOF的酪化活性最高;用硅藻土吸附固定化酶时,缓冲溶液的最适pH为7.0左右,每克酶粉加1.0mL缓冲溶液为最佳;固定化酶催化酯化的活性比游离的脂肪酶高.在酮基布洛芬与不同酰基受体(醇)的酶促酯化反应中,以丙醇的反应速度为最快.在由一种主溶剂与一种助溶剂组成的混合溶剂系统中,酶促酯化的速度要比在单一的主溶剂或助溶剂系统中快.当以1gP值较大的环己烷或异辛烷等为主溶剂,甲苯为助溶剂时,脂肪酶催化酮基布洛芬酯化反应的活性最高.     

Microwave-assisted synthesis of ethyl laurate using immobilized lipase: Optimization,mechanism and thermodynamic studies

Microwave-assisted synthesis of ethyl laurate using lauric acid and ethanol catalyzed by Fermase CALB has been investigated. The effect of operating parameters like molar ratio (lauric acid: ethanol), enzyme loading, temperature, and molecular sieves was systematically studied. A maximum conversion of 98.2% was obtained in 10 ​min compared to the conventional method, where the reaction required 4 ​h to achieve 92.4% conversion. The optimum parameters for the microwave-assisted synthesis were 1:2 ​M ratio of lauric acid to ethanol, 45 ​°C temperature, 1.8% (w/w) enzyme amount, 1.5% (w/w) molecular sieves. The enzyme lipase was reused for up to seven successive cycles under microwave irradiation. The thermodynamic study was carried out to determine various thermodynamic parameters for the reaction. The esterification mechanism was proposed, and the impact of microwave irradiation on the immobilized enzyme after several reuse was studied by scanning electron microscopy.     

Covalent immobilization of Candida antarctica lipase B on nanopolystyrene and its application to microwave-assisted esterification

Nanopolystyrene was used as a solid support for the covalent immobilization of Candida antarctica lipase B (CalB) using the photoreactive reagent 1-fluoro-2-nitro-4-azido benzene (FNAB) as a coupling reagent. The obtained derivative was then used as a biocatalyst in a microwave assisted esterification experiment. Factors such as contact time, pH, and enzyme concentration were investigated during immobilization. The hydrolytic activity, thermal, and operational stability of immobilized-CalB were determined. The maximum immobilized yield (218 μg/mg support) obtained at pH 6.8 exhibited optimum hydrolytic activity (4.42 × 10³ mU p-nitrophenol/min). The thermal stability of CalB improved significantly when it was immobilized at pH 10, however, the immobilized yield was very low (93.6 μg/mg support). The immobilized-CalB prepared at pH 6.8 and pH 10 retained 50% of its initial activity after incubation periods of 14 and 16 h, respectively, at 60 ℃. The operational stability was investigated for the microwave assisted esterification of oleic acid with methanol. Immobilized-CalB retained 50% of its initial activity after 15 batch cycles in the microwave-assisted esterification. The esterification time was notably reduced under microwave irradiation. The combined use of a biocatalyst and microwave heating is thus an alternative total green synthesis process.     

Collagen-Immobilized Lipases Show Good Activity and Reusability for Butyl Butyrate Synthesis

Candida rugosa lipases were immobilized onto collagen fibers through glutaraldehyde cross-linking method. The immobilization process has been optimized. Under the optimal immobilization conditions, the activity of the collagen-immobilized lipase reached 340 U/g. The activity was recovered of 28.3 % by immobilization. The operational stability of the obtained collagen-immobilized lipase for hydrolysis of olive oil emulsion was determined. The collagen-immobilized lipase showed good tolerance to temperature and pH variations in comparison to free lipase. The collagen-immobilized lipase was also applied as biocatalyst for synthesis of butyl butyrate from butyric acid and 1-butanol in n-hexane. The conversion yield was 94 % at the optimal conditions. Of its initial activity, 64 % was retained after 5 cycles for synthesizing butyl butyrate in n-hexane.     

Concentration,Partial Characterization,and Immobilization of Lipase Extract from <Emphasis Type="Italic">P. brevicompactum</Emphasis> by Solid-State Fermentation of Babassu Cake and Castor Bean Cake

One relevant limitation hindering the industrial application of microbial lipases has been attributed to their production cost, which is determined by the production yield, enzyme stability among other. The objective of this work was to evaluate the concentration and immobilization of lipase extracts from Penicillium brevicompactum obtained by solid-state fermentation of babassu cake and castor bean cake. The precipitation with ammonium sulfate 60% of saturation of crude extract obtained with babassu cake as raw material showed an enhancement in hydrolytic and esterification activities from 31.82 to 227.57 U/g and from 170.92 to 207.40 U/g, respectively. Concentrated lipase extracts showed preference to medium-chain triglycerides and fatty acids. It is shown that the enzyme activity is maintained during storage at low temperatures (4 and −10°C) for up to 30 days. Higher esterification activities were achieved when the lipase extract was immobilized in sodium alginate and activated coal.     

Synthesis of SBA-15 from low cost silica precursor obtained from sugarcane leaf ash and its application as a support matrix for lipase in biodiesel production

Ordered mesoporous silica material was synthesized from a low-cost precursor, sugarcane leaf ash, was used as a support matrix for lipase for the production of biodiesel. The mesoporous samples were characterized using Fourier transform infra red spectroscopy. The surface topography and morphology of the mesoporous materials were studied using scanning electron microscope. The pore diameter, pore volume, Brunauer Emmett and Teller surface area of the mesoporous material were determined by N₂ gas adsorption technique. Different pore size Santa Barbara Acid-15 (SBA-15) samples were synthesized and their lipase immobilization capacity and specific enzyme activity of immobilization lipase were determined and compared. Lipase from Candida Antarctica immobilized on SBA-15 (C) had shown maximum percentage immobilization and specific enzyme activity. The immobilized lipase mesoporous matrix was used for biodiesel production from crude non-edible Calophyllum inophyllum oil. The percentage yield of fatty acid methyl ester, 97.6 % was obtained under optimized conditions: 100 mg of lipase immobilized on SBA-15, 6:1 methanol to oil molar ratio, the reaction of 2 g C. inophyllum oil with methanol.     

Lipase Production in Solid-State Fermentation Monitoring Biomass Growth of Aspergillus niger Using Digital Image Processing

The aim of this study was to monitor the biomass growth of Aspergillus niger in solid-state fermentation (SSF) for lipase production using digital image processing technique. The strain A. niger 11T53A14 was cultivated in SSF using wheat bran as support, which was enriched with 0.91% (m/v) of ammonium sulfate. The addition of several vegetable oils (castor, soybean, olive, corn, and palm oils) was investigated to enhance lipase production. The maximum lipase activity was obtained using 2% (m/m) castor oil. In these conditions, the growth was evaluated each 24 h for 5 days by the glycosamine content analysis and digital image processing. Lipase activity was also determined. The results indicated that the digital image process technique can be used to monitor biomass growth in a SSF process and to correlate biomass growth and enzyme activity. In addition, the immobilized esterification lipase activity was determined for the butyl oleate synthesis, with and without 50% v/v hexane, resulting in 650 and 120 U/g, respectively. The enzyme was also used for transesterification of soybean oil and ethanol with maximum yield of 2.4%, after 30 min of reaction.     

Preparation and characterization of lipase immobilized on reversibly soluble-insoluble N-(2-carboxylbenzoyl) chitosan

N-(2-carboxylbenzoyl) chitosan (CBC), a reversibly soluble-insoluble polymer with pH change, was prepared by modifying chitosan backbone with phthalic anhydride and employed as carrier for lipase immobilization. The obtained CBC exhibited reversible solubility in aqueous solution; it was soluble at pH above 3.8 and precipitated at pH below 3.4. The porcine pancreatic lipase was covalently immobilized on CBC with glutaraldehyde as the crosslinking agent. Under the optimal immobilization condition, the retention activity of the immobilized lipase was found to be 69.8 %. The maximum activity of lipase immobilized on CBC was observed at 40 °C, pH 8.0, while the free lipase presented maximum activity at 37 °C, pH 7.5. The lipase immobilized on CBC exhibited improved thermal and storage stabilities and retained 58.7 % of its initial activity after 9 times of repeated use.     

单分散磁性纳米粒子固定化猪胰脂肪酶的研究

借助溶热法制备了一种亲水及生物相容良好的Fe3O4磁性纳米粒子,用γ-氨丙基三乙氧基硅烷直接对所得磁性粒子表面改性,然后用戊二醛偶联法制得了固定化猪胰脂肪酶.表征研究显示,所得磁性粒子粒径约200 nm,具有良好的单分散性和磁响应性.考察了戊二醛浓度、给酶量和反应时间对脂肪酶固定化过程的影响,并通过游离酶与固定化酶的比...     

Enzymatic Synthesizing of Phytosterol Oleic Esters

A method of synthesizing the phytosterol esters from oleic acid and sterols was studied, using immobilized lipase Candida sp. 99-125 as catalyst. Molar ratio (oleic acid/phytosterols), temperature, reaction period, organic solvents, catalyst, and silica-gel drier were optimized, and the result showed that 93.4% of the sterols had been esterified under the optimal synthetic condition: the molar ratio of oleic acid/phytosterol is 1:1 in 10 mL iso-octane, immobilized lipase (w, 140% of the sterols), incubated in an orbital shaker (200 rpm) at a temperature of 45 °C for 24 h. The immobilized lipase could be reused for at least 13 times with limited loss of esterification activity. The conversion still maintained up to 86.6%. Hence, this developed process for synthesizing phytosterol esters could be considered as simple and low-energy consumption compared to existing chemical processes.     

Synthetic reactions catalyzed by immobilized lipase from oilseed rape (Brassica napus L.)

Lipase from rape (Brassica napus L., immobilized onto celite, catalyzes esterification and transesterification reactions in hexane. The activity of the lipase is stimulated up to 35 fold by the addition of water (1.3% w/v). The activity of the lipase in hydrolysis is about 8 times higher than in the esterification reactions in hexane. Interesteri-fication reactions between mono- and diacylglycerols and transesterification reactions of mono- and diacylglycerols with alcohols were also catalyzed at relatively high rates but transesterification/esterification of these acylglycerols with fatty acids was comparatively slow. In transesterification reactions, triacylglycerols reacted rather slowly.     

Immobilized Lipase from Candida sp. 99–125 on Hydrophobic Silicate: Characterization and Applications

Lipase Candida sp. 99–125 has been proved to be quite effective in catalyzing organic synthesis reactions and is much cheaper than commercial lipases. Mesoporous silicates are attractive materials for the immobilization of enzymes due to their unique structures. The present research designed a hydrophobic silicate with uniform pore size suitable for the comfort of lipase Candida sp. 99–125 for improving its activity and stability. The resulting immobilized lipase (LP@PMO) by adsorption was employed to catalyze hydrolysis, esterification, and transesterification reactions, and the performances were compared with the lipase immobilized on hydrophilic silicate (LP@PMS) and native lipase. The LP@PMO showed as high activity as that of native lipase in hydrolysis and much increased catalytic activity and reusability in the reactions for biodiesel production. Besides, LP@PMO also possessed better organic stability. Such results demonstrate that immobilization of lipase onto hydrophobic supports is a promising strategy to fabricate highly active and stable biocatalysts for applications.     

有机相中固定化脂肪酶催化合成植物甾醇酯

酶法合成植物甾醇酯具有反应条件温和、产物纯度和产量高等优点,但非水相酶催化的活性和稳定性普遍较低.本文以大孔树脂固定化脂肪酶为催化剂,并在催化过程中添加乳糖的类似物,构建了有机相高效合成植物甾醇酯的工艺过程.以酯化率为考察指标,对脂肪酶和反应溶剂进行筛选,对酯化条件进行优化,同时考察了糖的种类及添加量对酶催化性能的影响.结果表明,大孔树脂NKA吸附固定化的褶皱假丝酵母(Candida rugosa)脂肪酶(NKA-CRL)为最适宜的催化剂,以正己烷为反应介质,在酸醇摩尔比为2和添加酶蛋白质量7.5%的海藻糖的条件下,40°C反应10 h,酯化率达到96.6%.连续6次催化后,植物甾醇的酯化率仍维持在85.0%以上.     

纳米-微米复合孔泡沫陶瓷固定化脂肪酶

考察了泡沫陶瓷的孔径分布和表面性质对脂肪酶固定化的影响.研究表明,泡沫陶瓷的纳米孔孔径分布非常适合脂肪酶的固定化,对固定化酶的催化效率有决定性的影响.经1h的定化,泡沫陶瓷固定化酶的活性达商业化硅藻土固定化酶的1.33倍,体积活力为其2.63倍,蛋白载量为45.36mg/g陶瓷,比活为1215.39U/g,活力回收为41.2%.泡沫陶瓷固定化脂肪酶在有机相乙酸乙酯合成中表现优良,连续使用5次,每次反应3h,乙酸转化率均在93%左右.     

非水相中固定化脂肪酶催化性能的研究

以离子交换树脂为载体,用离子交换吸附法固定化脂肪酶,对影响固定化过程的各种因素进行了考察,确定了最优条件。得到的固定化酶催化合成月桂酸月桂醇酯,考查了在不同lgP值有机溶剂中的催化反应,异辛烷为最佳反应介质,最佳水含量为8％,最佳酸醇摩尔比为1：2,最适催化温度为55℃,得到的活化能Eα为19．00kJ／mol。     

聚乙烯亚胺改性聚丙烯腈中空膜固定脂肪酶

聚丙烯腈是富腈基的高分子聚合物,易修饰改性,广泛应用于膜分离应用.我们以聚丙烯腈中空膜为载体,采用化学法交联聚乙烯亚胺并固定脂肪酶,固定过程中引入海藻酸钠,用CaCl_2进行后处理,得到固定化脂肪酶PAN-PEI-SA/E-CaCl_2载酶量为31.70(mg enzyme)/(g support),酶活为50.20 U/(g support),15次重复使用可保留58.77%的酶活,与游离酶相比耐酸性和耐温性有所提高,相同条件下与Nov 435相比,酶活更高,这表明最终得到的固定化脂肪酶有良好的工业应用前景.     

Adsorption and activity of lipase from Candida rugosa on the chitosan-modified poly(acrylonitrile-co-maleic acid) membrane surface

Efforts have recently been made to improve the biocompatibility of support surface for enzyme immobilization, which could create a specific microenvironment for the enzymes and thus benefit the enzyme activity. In this work, one natural macromolecule, chitosan, was tethered on the surface of poly(acrylonitrile-co-maleic acid) (PANCMA) membrane to prepare a dual-layer biomimetic support for enzyme immobilization. Lipase from Candida rugosa was immobilized on this dual-layer biomimetic support by adsorption. The properties of the immobilized enzyme were assayed and compared with those of the free one. It was found that the adsorption capacity of lipase on the chitosan-tethered PANCMA membrane increases with the decrease of ionic strength and there is an optimum pH value for the adsorption. The activity retention of the immobilized lipase on the chitosan-tethered membrane by adsorption (54.1%) is higher than that by chemical bonding (44.5%). In comparison with the immobilized lipase by chemical bonding, there is a decrease of the K(m) value and an increase of the V(max) value for the immobilized lipase by adsorption. Additionally, the experimental results of thermal stabilities indicate that the residual activity of the immobilized lipase at 50 degrees C is 38% by adsorption and 65% by chemical bonding.     

亲水梳状环氧聚合物载体柔性固定化脂肪酶

以氯乙酰化聚苯乙烯微球载体为大分子引发剂,以甲基丙烯酸缩水甘油酯和亲水性丙烯酰胺为共聚接枝单体,以氯化亚铜及2,2'-联吡啶为催化体系,采用原子转移自由基聚合法接枝合成了具有柔性链的亲水梳状环氧聚合物载体PS-acyl-P(AM-co-GMA),并将其用于耐有机溶剂YCJ01脂肪酶的共价柔性固定化.结果表明,固定化酶催...     

Metal-Chelate Immobilization of Lipase onto Polyethylenimine Coated MCM-41 for Apple Flavor Synthesis

An enzyme immobilized on a mesoporous silica nanoparticle can serve as a multiple catalyst for the synthesis of industrially useful chemicals. In this work, MCM-41 nanoparticles were coated with polyethylenimine (MCM-41@PEI) and further modified by chelation of divalent metal ions (M = Co²⁺, Cu²⁺, or Pd²⁺) to produce metal-chelated silica nanoparticles (MCM-41@PEI-M). Thermomyces lanuginosa lipase (TLL) was immobilized onto MCM-41, MCM-41@PEI, and MCM-41@PEI-M by physical adsorption. Maximum immobilization yield and efficiency of 75 ± 3.5 and 65 ± 2.7% were obtained for MCM@PEI-Co, respectively. The highest biocatalytic activity at extremely acidic and basic pH (pH = 3 and 10) values were achieved for MCM-PEI-Co and MCM-PEI-Cu, respectively. Optimum enzymatic activity was observed for MCM-41@PEI-Co at 75 °C, while immobilized lipase on the Co-chelated support retained 70% of its initial activity after 14 days of storage at room temperature. Due to its efficient catalytic performance, MCM-41@PEI-Co was selected for the synthesis of ethyl valerate in the presence of valeric acid and ethanol. The enzymatic esterification yield for immobilized lipase onto MCM-41@PEI-Co was 60 and 53%, respectively, after 24 h of incubation in n-hexane and dimethyl sulfoxide media.

Open image in new window

Graphical Abstract Divalent metal chelated polyethylenimine coated MCM-41 (MCM-41@PEI-M) was used for immobilization of Thermomyces lanuginosa lipase catalyzing green apple flavor preparation

     

Covalent attachment of microbial lipase onto microporous styrene-divinylbenzene copolymer by means of polyglutaraldehyde

A novel method for immobilization of Thermomyces lanuginosus lipase onto polyglutaraldehyde-activated poly(styrene-divinylbenzene) (STY-DVB), which is a hydrophobic microporous support has been successfully developed. The copolymer was prepared by the polymerization of the continuous phase of a high internal phase emulsion (polyHIPE). The concentrated emulsion consists of a mixture of styrene and divinylbenzene containing a suitable surfactant and an initiator as the continuous phase and water as the dispersed phase. Lipase from T. lanuginosus was immobilized covalently with 85% yield on the internal surface of the hydrophobic microporous poly(styrene-divinylbenzene) copolymer and used as a biocatalyst for the transesterification reaction. The immobilized enzyme has been fully active 30 days in storage and retained the activity during the 15 repeated batch reactions. The properties of free and immobilized lipase were studied. The effects of protein concentration, pH, temperature, and time on the immobilization, activity, and stability of the immobilized lipase were also studied. The newly synthesized microporous poly(styrene-divinylbenzene) copolymer constitutes excellent support for lipase. It given rise to high immobilization yield, retains enzymatic activity for 30 days, stable in structure and allows for the immobilization of large amount of protein (11.4mg/g support). Since immobilization is simple yet effective, the newly immobilized lipase could be used in several application including oil hydrolysis, production of modified oils, biodiesel synthesis, and removal of fatty acids from oils.