聚丙烯酸甲酯载体对柱状假丝酵母脂肪酶固定化的研究（Ⅰ）

合成了一系列不同结构的聚丙烯酸甲酯，考察了它们的固定化酵母脂肪酶催化酯水解反应的效果，得到了载体孔结构对固定化效果影响的一些规律．研究了最佳吸附条件，比较ｐＨ和离子强度对酵母脂肪酶自由酶和固定化酶催化酯水解反应活力的影响．     

琼脂固定化过氧化氢酶的催化活性

采用琼脂包埋法对过氧化氢酶进行固定化,考察了固定化过氧化氢酶催化过氧化氢降解的活性,确定了最佳催化反应条件.结果表明,经琼脂包埋法固定化后,过氧化氢酶仍保留较高的催化活性,其催化过氧化氢分解反应的最佳条件为温度35℃、pH 9.0.与此同时,固定化过氧化氢酶具有更强的温度适应能力和更宽的pH作用范围,并具有一定的重复使用性能.     

负载型CaSO4/离子交换树脂催化合成单十二烷基磷酸酯

采用浸渍法制备了负载型金属盐离子交换树脂催化剂,考察了以磷酸与月桂醇为原料催化合成单十二烷基磷酸酯的催化性能.负载不同金属盐离子对单十二烷基磷酸酯的收率的影响表明,CaSO4负载离子交换树脂催化合成单十二烷基磷酸酯效果最好.研究发现,在CaSO4负载量1.2%,催化剂用量为总反应物质量的3%,反应温度90℃,反应12h工艺条件下,月桂醇的转化率为79.4%,单酯选择性为99.9%;加入环己烷作为带水剂,相同条件下,月桂醇转化率为92.3%,单酯选择性为99.9%,并且催化剂重复使用7次之后,催化性能仍保持不变.     

交联烯丙基葡聚精凝胶固定化脂肪酸的研究

本文研究了烯丙基葡聚糖和N、N＇－亚甲基双丙烯酰胺经反相悬浮聚合包埋固定化脂肪酶的方法。考察了悬浮介质、交联度对固定化酶的影响，得出了包埋固定化脂肪酶的最佳条件；并测定了固定化脂肪酶的催化性能，确定了该固定化酶催化橄榄油水解的最适条件。     

基于氯化镁饱和溶液中固定化脂肪酶Lipozyme TL IM催化光皮树油脂合成生物柴油

基于氯化镁饱和溶液反应体系中,对采用固定化脂肪酶Lipozyme TL IM催化光皮树油脂转化为生物柴油的工艺进行了研究。考察了固定化脂肪酶Lipozyme TL IM催化光皮树油转酯化的工艺中甲醇的用量、固定化脂肪酶的添加量、摇床的转速和反应时间对生物柴油产率的影响。实验结果表明,采用氯化镁饱和溶液反应体系,在醇油摩尔比为3∶1,固定化酶Lipozyme TL IM用量为光皮树油质量的20%,摇床转速为150 r/min,反应8 h时,生物柴油产率最高,达到86.5%。与传统的三步甲醇醇解或者有机溶剂反应体系比较,采用的氯化镁饱和溶液体系的酶稳定性更好,反应效率更高,有效地解决了酶在甲醇中失活的问题,生产成本低,可成为生产生物柴油的新工艺。     

固定化脂肪酶催化麻疯树油与碳酸二甲酯制备生物柴油的研究

以介孔硅材料(MPS)为载体将脂肪酶固定化,以碳酸二甲酯为酰基受体,对固定化酶催化碳酸二甲酯进行了反应路径(原料油)、反应条件(反应温度、碳酸二甲酯的用量、加水量)的优化,在最佳的条件下对实验过程中所用的固定化酶进行重复使用性的考察。实验结果表明,不同种油与碳酸二甲酯反应在固定化酶的催化下制备生物柴油的产率以麻疯树油为最高,最佳反应条件是碳酸二甲酯的浓度为16m L/g、不加水,在50℃下反应24h,生物柴油得率达81.6%。     

双层固定化酵母催化还原4-氯-乙酰乙酸乙酯的研究

以海藻酸钠为内层载体,利用机械强度良好的聚乙烯醇(PVA)改性海藻酸钠混合物作为外层载体,双层固定化高活性酵母,得到固载的生物催化剂,用于由磷酸缓冲溶液和环己烷组成的双相体系,对4-氯-乙酰乙酸乙酯(COBE,ethyl 4-cloro-3-oxobutyrate)进行不对称催化加氢合成(S)-4-氯-3-羟基丁酸乙酯[(S)-CHBE],ethyl[(S)-4-chloro-3-hydro butanoate].在最适条件下,双层固定化酵母的不对称催化还原反应优于游离细胞和单层固定化细胞.在底物COBE的最佳浓度和进料速率分别为170mmol/L,125mL/h的连续操作条件下,最高(S)-CHBE转化率为94.2%,最高对映体过量值为98%.与游离细胞催化COBE相比,反应转化率提高3%,最佳底物浓度比游离细胞增加1倍;与单层固定化细胞催化还原相比,对映体过量值提高8%.连续性实验表明,双层固定化酵母细胞在连续使用5d,其转化率和对映选择性没有明显下降.     

固定化乳酸脱氢酶活性的X射线微区分析

利用X射线微区分析，对吸附法得到的固定化乳酸脱氢酶的活性进行了分析；以乳酸为底物，铁氰化钾及铜离子作为捕捉剂，底物经乳酸脱氢酶及氧化型辅酶NAD^ 的作用下催化产生丙酮酸，反应生成的还原性辅酶NADH使铁氰化物还原为亚铁氰化物，后者和铜离子反应产生具有高电子密度的亚铁氰化铜沉淀，可以确定固定化乳酸脱氢酶的催化活性部位；结果表明，以合成出的大孔吸附树脂为固定化酶载体，其酶活性较高，活性乳酸脱氢酶分布较均匀，得到了固定化乳酸脱氢酶的活性定位的最佳条件，并对不同结构载体固定化酶活性进行了研究。     

固定化脂肪酶催化碳酸二甲酯制备生物柴油的研究

以介孔硅材料(MPS)为载体将脂肪酶固定化,以碳酸二甲酯为酰基受体,对固定化酶催化碳酸二甲酯进行了反应路径(原料油)、反应条件(反应温度、碳酸二甲酯的用量、加水量)的优化,在最佳的条件下对实验过程中所用的固定化酶进行重复使用性的考察.实验结果表明,不同种油与碳酸二甲酯反应在同定化酶的催化下制备生物柴油的产率以麻疯树油为最高,最佳反应条件是碳酸二甲酯的浓度为16mL/g、不加水,在50℃下反应24h,生物柴油得率达81.6％.     

核苷酸锆固定化脂肪酶的制备及其催化性能

开发了以核苷酸锆纳米颗粒为载体固定化脂肪酶的方法,考察了固定化时间、缓冲液pH值及浓度和酶载量等因素对固定化酶在有机相中催化烯丙醇酮酯交换反应性能的影响.结果表明,一元尿苷酸锆(粒径30～50nm)是较佳的载体,在磷酸缓冲液pH=8.0和浓度为0.03mol/L时,酶与载体质量比为4,固定化6h制得的固定化酶效果最佳....     

混合溶剂系统中固定化脂肪酶对酮基布洛芬的催化酯化反应

以硅藻土吸附的脂肪酶为催化剂,对外消旋酮基布洛芬[2-(3-苯甲酰苯基)丙酸]进行对映选择性酯化反应;考察了不同的脂肪酶制剂,固定化时所加缓冲液的体积与pH值,酰基受体(醇)的种类以及混合溶剂系统的组成等因素对酶活性的影响.结果表明,在所考察的7种脂肪酶中,以LipaseOF的酪化活性最高;用硅藻土吸附固定化酶时,缓冲溶液的最适pH为7.0左右,每克酶粉加1.0mL缓冲溶液为最佳;固定化酶催化酯化的活性比游离的脂肪酶高.在酮基布洛芬与不同酰基受体(醇)的酶促酯化反应中,以丙醇的反应速度为最快.在由一种主溶剂与一种助溶剂组成的混合溶剂系统中,酶促酯化的速度要比在单一的主溶剂或助溶剂系统中快.当以1gP值较大的环己烷或异辛烷等为主溶剂,甲苯为助溶剂时,脂肪酶催化酮基布洛芬酯化反应的活性最高.     

Immobilization of lipase B within micron-sized poly-N-isopropylacrylamide hydrogel particles by solvent exchange

The aim of the present work is the use of a water soluble enzyme in an organic solvent, still with a pronounced catalytic activity. Therefore, lipase B from Candida antarctica (CalB) is immobilized within micron-sized thermosensitive p-NIPAM hydrogel particles using a solvent exchange from polar to organic solvents. The absorbed amount of CalB is investigated at different immobilization temperatures. Confocal laser scanning microscopy (CLSM) shows that CalB is homogeneously distributed within the polymer network. An enhanced specific activity of CalB in n-hexane is achieved after immobilization within the p-NIPAM microgels. In order to get information on the supply of the substrate depending on the temperature, the activity is determined at different reaction temperatures. Additionally, the system is stable in the organic solvent, namely n-hexane, and shows a good reusability.     

Immobilization of Candida cylindracea Lipase by Covalent Attachment on Glu-Modified Bentonite

Alkaline Ca-bentonite, obtained upon acid activation and base load of natural bentonite, has a good anion exchange capability. Glu-modified alkaline Ca-bentonites were further prepared by covalent binding with glutamic acid for the immobilization of lipase OF from Candida cylindracea. The obtained immobilized lipase demonstrated a significantly higher catalytic activity than that of unmodified alkaline Ca-bentonite, giving a specific activity of 62.1 U mg⁻¹ protein, twice that of the unmodified carrier, and a total activity of 391.2 U g⁻¹ support, retaining ~ 82.3% of the activity after being reused five times for olive oil emulsion hydrolysis. X-ray diffraction and Fourier transform infrared spectroscopy assays demonstrated the successful immobilization of the lipase on the surface of the bentonite. Upon immobilization, the thermostability of the lipase improved remarkably. At 50 °C, free lipase retained only 6.0% of its initial activity at 6 h, in comparison with 15% for Ca-Bent-lipase and 50% for Glu-Ca-Bent-lipase after 8 h. The Glu-Ca-Bent-lipase is proved as an effective biocatalyst for the biodiesel preparation, improving the transesterification reaction conversion from 52.8% in the condition of free lipase to 99.9% and keeping at 56.2% after being reused five times, while the free lipase was inactive upon two reuses. The above results provide a new route in the use of inexpensive bentonite for the enzyme immobilization.

     

Synthesis of monobutyrylglycerol by transesterification with soluble and immobilized lipases

Transesterification between ethyl butyrate and glycerol using very different lipase preparations (native, modified, and immobilized) in a two-phase system—no extra solvent added—has been investigated. Optimal conversion was obtained with the presence of 5% water in the reaction mixture. Only monobutyrin was produced in all conditions tested. The best enzyme preparations were nativeCandida cylindracea lipase,Mucor miehei lipase immobilized on a phenol-formaldehyde exchange resin (Lipozyme?), andC. cylindracea lipase immobilized on Celite.     

Lipase Immobilized on the Hydrophobic Polytetrafluoroethene Membrane with Nonwoven Fabric and Its Application in Intensifying Synthesis of Butyl Oleate

The synthesis of butyl oleate was studied in this paper with immobilized lipase. Five types of membrane were used as support to immobilize Rhizopus arrhizus lipase by following a procedure combining filtration and protein cross-linking. Results showed that hydrophobic polytetrafluoroethene membrane with nonwoven fabric (HO-PTFE-NF) was the favorite choice in terms of higher protein loading, activity, and specific activity of immobilized lipase. The factors including solvent polarity, lipase dosage, concentration, and molar ratio of substrate and temperature were found to have significant influence on conversion. Results showed that hexane (logP = 3.53) was a favorable solvent for the biosynthesis of butyl oleate in our studies. The optimal conditions were experimentally determined of 50 U immobilized lipase, molar ratio of oleic acid to butanol of 1.0, substrate concentration of 0.12 mol/L, temperature of 37 °C, and reaction time of 2 h. The conversion was beyond 91% and decreased slightly after 18 cycles. Lipase immobilization can improve the conversion and the repeated use of immobilized lipase relative to free lipase.     

Enzymatic resolution of (RS)-β-hydroxy selenides in organic media

Kinetic resolutions of a number of β-hydroxy selenides promoted by enzymes were performed using PPL (free Porcine pancreatic lipase), PSL (Amano PS—free Pseudomonas sp. lipase) and CALB (NOVOZYM 435^®—immobilized Candida Antarctica lipase type B) with (RS)-1-phenylselanyl-propan-2-ol. CALB gave the best results and provided both (R)- and (S)-enantiomers in high enantiomeric purity. A comparative study of the effect of temperature, solvent, enzyme immobilization and the structure of the substrates on the resolution is presented.     

有机相中α-氰基-3-苯氧基苄醇乙酯的酶促醇解反应

研究了有机相中脂肪酶催化α-氰基-3-苯氧基苄醇乙酯的醇解化反应。制备α -氰基-3-苯氧基苄醇。考察了酶、溶剂、醇、醇用量、溶剂水含量以及底物浓度等 因素对反应的影响，结果表明Novozym435脂肪酶催化活性最高，经实验确定的最佳 条件为：脱水甲苯为溶剂，正辛醇为酰基受体，正辛醇、酯的摩尔比为1.5:1，酶 量为8 mg/mL时的最佳底物浓度为108.13 mmol/L，在上述条件下反应30 h酯的转化 率 > 96%。     

Isolation of thermo-stable and solvent-tolerant Bacillus sp. lipase for the production of biodiesel

This study presents the production of biodiesel from algae oil by transesterification using thermophilic microorganism. The microorganism used in this study was isolated from the soil sample obtained near the furnace. The organism was identified as Bacillus sp., and the lipase obtained was purified by ammonium sulfate precipitation and ion exchange chromatography leading to 8.6-fold purification and 13% recovery. Molecular weight of the enzyme was determined by sodium dodecyl sulfate-polyacrylamide gel electrophoresis, and it was found to be 45 kDa. The effect of pH, temperature, and solvent addition on lipase activity was investigated. The enzyme showed maximum activity at 55 °C and at pH 7 and was also found to be highly active in the presence of organic solvents such as hexane and t-butanol. The isolated lipase was successfully used for the production of biodiesel. The transesterification activity of the isolated lipase showed 76% of fatty acid methyl esters yield in 40 h, which indicated that this enzyme can be used as a potential biocatalyst for the biodiesel production.     

Biodiesel fuel production by the transesterification reaction of soybean oil using immobilized lipase

The enzymatic alcoholysis of soybean oil with methanol and ethanol was investigated using a commercial, immobilized lipase (Lipozyme RMIM). The effect of alcohol (methanol or ethanol), enzyme concentration, molar ratio of alcohol to soybean oil, solvent, and temperature on biodiesel production was determined. The best conditions were obtained in a solvent-free system with ethanol/oil molar ratio of 3.0, temperature of 50 degrees C, and enzyme concentration of 7.0% (w/w). Three-step batch ethanolysis was most effective for the production of biodiesel. Ethyl esters yield was about 60% after 4 h of reaction.