MoS_2负载量对MoS_2/TiO_2光催化降解苯酚效率的影响及其作用机理研究

通过水解法制备TiO_2纳米颗粒,与经过超声处理后的MoS_2片层纳米材料复合制备MoS_2/TiO_2纳米催化剂,考察不同MoS_2负载量对其光催化降解苯酚效率及路径的影响。XRD、SEM、EDS、FT-IR和UV-vis DRS等表征结果表明,复合催化剂主要由锐钛矿型TiO_2和MoS_2组成;剥离后的MoS_2呈现薄片层状结构,均匀地分散在TiO_2纳米颗粒当中。光催化降解苯酚性能测试结果显示,对于MoS_2/TiO_2催化剂,MoS_2负载量的提高有利于光催化降解苯酚效率的提高;当MoS_2负载量为27%时,复合M o S2/TiO_2纳米颗粒的光催化性能最佳,反应80 min后可将苯酚完全降解。通过对苯酚降解过程中生成中间产物跟踪发现,MoS_2负载量的提高有利于促进中间产物苯醌、对苯二酚以及邻苯二酚的生成,进而提升了MoS_2/TiO_2复合材料的光催化性能。     

Photocatalytic degradation and kinetics of Orange G using nano-sized Sn(IV)/TiO2/AC photocatalyst

Sn(IV) doped and nano-sized TiO₂ immobilized on active carbon (AC) (Sn(IV)/TiO₂/AC) were prepared by the sol–gel and dip-calcination method. An azo dye, Orange G (OG), was used as a model compound to study its photocatalytic activity in a fluidized bed photoreactor. The addition of Sn(IV) on TiO₂ could greatly improve the activity of TiO₂, and the optimal amount of tin was 2.5 at.%. The effects of calcination temperature, pH value, the initial hydrogen peroxide concentration ([H₂O₂]₀), the catalyst amount ([TiO₂]), the initial OG concentration ([dye]₀) and co-existing negative ions on the photocatalytic activity of Sn(IV)/TiO₂/AC were studied. The optimal conditions were as follows: pH 2.00, [H₂O₂]₀ = 1.5mL/L, [dye]₀ = 50 mg/L, [TiO₂] = 12.5 g/L, when the 300 W high pressure mercury light was used as the light source. Under these conditions, the degradation efficiency of OG reached 99.1% after 60 min reaction. The kinetics of the OG degradation was also analyzed. The results showed that the kinetics of this reaction fit the Langmiur–Hinshelwood kinetics model well and the absorption of OG on the Sn(IV)/TiO₂/AC surface was the controlling step in the whole degradation process. In addition, the catalyst, liquid and gas were separated effectively, and the integrative process of reaction and separation was achieved during the experiment.     

微波辅助溶剂热合成In-Si共改性TiO_2的增强光催化性能

利用微波辅助溶剂热法合成了In-Si共改性的TiO2光催化剂.粉末X射线衍射(XRD)、激光拉曼(Raman)光谱、N2吸脱附(BET)、X射线光电子能谱(XPS)、光致发光(PL)光谱和紫外-可见漫反射光谱(UV-Vis DRS)等实验表明,尽管掺杂和改性后TiO2结晶度略有降低,但不影响光催化剂锐钛相的形成.Si掺杂入TiO2晶格使颗粒变小,比表面积变大.In不能进入TiO2晶格,在TiO2表面形成了In2O3.罗丹明B(RhB)降解实验显示,In-Si共改性TiO2表现出很高的紫外和可见光催化活性,Si:In:Ti的摩尔比为0.03:0.02:1的样品(IST-2)光催化活性最高,紫外光下3 min即可将RhB降解完全,可见光下120 min RhB降解率为97%,这是由材料的高表面积,In2O3-TiO2复合半导体之间高效电荷转移及染料敏化等共同作用所致.对于苯酚,光催化降解则相对缓慢,700 min内尚不能降解完全.     

Sn4+掺杂对TiO2纳米颗粒膜光催化降解苯酚活性的影响

金属离子掺杂能改善TiO2纳米微粒光催化活性,在光降解大气和水污染物的研究中,已引起人们的重视[1,2].实验证明,掺杂物的浓度、掺杂离子的分布、掺杂能级与TiO2能带匹配程度、掺杂离子d电子的组态、电荷的转移和复合等因素对催化剂的光催化活性有直接影响[3].Kamat等[4]曾利用TiO2颗粒与SnO2颗粒混合制膜,使光催化剂活性得到提高.但Sn4+掺杂TiO2用于光催化剂尚少见报道.本文采用等离子体化学气相沉积法(PECVD)[5]制备了Sn4+离子掺杂的TiO2纳米颗粒膜催化剂(TiO2-Sn),考察了其对苯酚的光催化降解活性,讨论了Sn4+离子的掺杂方式及光催化活性提高的机理.     

Synthesis of nanosized TiO2 particles in reverse micelle systems and their photocatalytic activity for degradation of toluene in gas phase

Nanosized pure TiO₂ particles with high crystallinity and large surface area were prepared by hydrolysis of tetrabutyl titanate in water/Triton X-100/isooctane reverse micelle solutions as reaction media followed by hydrothermal treatment to improve crystallinity. The prepared TiO₂ nanoparticles were characterized by XRD, BET, TGA, FT-IR and TEM. The size of ultrafine particles was controlled by changing the water content of the reverse micelle solution. The TiO₂ particles showed monodispersity, large surface area and high degrees of crystallinity and thermostability. The photocatalytic activity of the TiO₂ particles was evaluated by decomposition of toluene in the gas phase. The activity of the TiO₂ nanoparticles was higher than that of commercially available anatase fine particles, such as ST-01, which is one of the most active photocatalysts for degradation of organic compounds in the gas phase.     

LaNiO3/TiO2纳米管阵列的电化学制备及其光催化性能

利用脉冲电沉积与高温退火相结合的方法制备了镍酸镧(LaNiO₃)纳米颗粒负载的二氧化钛(TiO₂)纳米管阵列. 修饰于TiO₂纳米管阵列上的LaNiO₃纳米颗粒粒径小（< 10 nm）、分布均匀、负载量可控,一些LaNiO₃纳米颗粒沉积于TiO₂纳米管内. 紫外可见吸收光谱显示,LaNiO₃/TiO₂纳米管阵列的吸收带边较TiO₂纳米管阵列明显红移,可见光吸收明显增强. 可见光下光催化降解罗丹明B（RhB）的结果表明,脉冲循环沉积500次制得的LaNiO₃/TiO₂纳米管阵列的光催化活性最佳,其对RhB光催化降解速率是TiO₂纳米管阵列的3.5倍,并且表现出极好的光催化稳定性.     

Keggin型铬取代的磷钨杂多阴离子/二氧化钛纳米膜光催化剂的制备及可见光催化性能

以钛酸四丁酯Ti(OC₄H₉)₄为TiO₂前驱体,Keggin型铬取代的杂多阴离子PW₁₁Cr为可见光活性组分,采用溶胶-凝胶提拉法在玻片表面制备了PW₁₁Cr/TiO₂纳米膜光催化剂,并用UV-Vis DRS、IR、XRD、SEM和TEM等技术手段对催化剂的光吸收性质、化学组成、晶相和表面结构形貌等进行了表征;讨论了膜中PW₁₁Cr和TiO₂相互作用的方式;以染料模型污染物RhB的可见光催化降解为探针,评估了PW₁₁Cr/TiO₂光催化剂的可见光催化活性,讨论了光催化反应机理,并与TiO₂的光催化反应机理进行了比较;考察了焙烧温度、PW₁₁Cr剂量和溶液pH值对光催化活性的影响;最后用RhB的循环降解实验评估了催化剂的光催化稳定性。 实验结果表明,PW₁₁Cr/TiO₂光催化剂对可见光有明显吸收,较低焙烧温度(100 ℃)下得到的膜为无定形结构,而较高焙烧温度(500 ℃)为纳晶结构;前者的光催化活性较高,在200 W金卤灯照射下降解10 μmol/L RhB,120 min的降解率为95%,4 h的COD去除率为72%;羟基自由基是导致RhB降解的主要氧活性物质;低的膜处理温度,高的PW₁₁Cr负载量和溶液酸性有利于提高PW₁₁Cr/TiO₂膜的光催化活性;经循环重复使用10次,PW₁₁Cr/TiO₂膜的光催化活性仅有较少损失。     

Characterization and photocatalytic properties of silver and silver chloride doped TiO2 hollow nanoparticles

Using polystyrene（PSt） particles as template,PSt/TiO₂ composite particles with AgCl incorporation were prepared through hydrolysis of tetrabutyl titanate in the presence of AgNO₃ and NaCl.AgCl doped TiO₂ hollow particles were successfully prepared with the PSt/TiO₂ composite microspheres pretreated at 180℃followed by calcination.The morphology of PSt/TiO₂ particles and the crystal structures of the AgCl doped TiO₂ hollow particles were characterized.The photocatalytic activity of the doped TiO₂ hollow particles in degradation of Rhodamine B was tested under UV and visible lights and compared to that with Ag doped TiO₂ particles.The results showed that TiO₂ hollow particles,either doped with Ag or AgCl,demonstrated higher photocatalytic activity than the pure TiO₂ particles.This enhancement in photocatalytic activity was more significant with AgCl doped TiO₂ than that with Ag doped,and more distinct when the degradation was done under visible light than that under LTV light.     

Enhanced Visible-light Photocatalytic Activity of g-C3N4/Nitrogen-doped Graphene Quantum Dots/TiO2 Ternary Heterojunctions for Ciprofloxacin Degradation with Narrow Band Gap and High Charge Carrier Mobility

Limited visible-light absorption and high recombination rate of photogenerated charges are two main drawbacks in g-C₃N₄-based photocatalysts. To solve these problems, g-C₃N₄/nitrogen-doped graphene quantum dots (NGQDs)/TiO₂ ternary heterojunctions were facilely prepared via a one-step calcining method. The morphology, structure, optical and electrochemical properties of g-C₃N₄/NGQDs/TiO₂ were characterized and explored. The optimal g-C₃N₄/NGQDs/TiO₂ composite exhibits enhanced photocatalytic degradation performance of ciprofloxacin (CIP) compared with the as-prepared g-C₃N₄, TiO₂(P25) and g-C₃N₄/TiO₂ heterojunction under visible light irradiation. The apparent rate constant of the composite is around 6.43, 4.03 and 2.30 times higher than those of g-C₃N₄, TiO₂ and g-C₃N₄/TiO₂, respectively. The enhanced photocatalytic efficiency should be mainly attributed to the improvement of light absorption and charge separation and transfer efficiency, originating from the narrow band gap and high charge carrier mobility. The active species trapping experiments results showed that the h⁺ and ^·O₂^- were the main active species in the degradation process. A possible photocatalytic reaction mechanism of the g-C₃N₄/NGQDs/TiO₂ composite for the enhanced degradation of CIP under visible light irradiation was also proposed.     

Preparation and Photocatalysis of Mesoporous TiO2 Nanofibers via an Electrospinning Technique

Mesoporous TiO₂ nanofibers have been synthesized by a new method that combines sol-gel chemistry and electrospinning technique. The obtained mesoporous TiO₂ nanofibers were characterized with scanning electron microscopy(SEM), X-ray diffraction(XRD), transmission electron microscopy(TEM) and nitrogen adsorption-desorption isotherms. The photocatalytic performance was evaluated by the photocatalytic degradation of Rhodamine B under UV light irradiation. The results show that mesoporous TiO₂ nanofibers exhibit higher photocatalytic activity compared with nonporous TiO₂ nanofibers.     

金红石相TiO_2纳米棒的氢化处理及其光催化活性

以钛酸四丁酯为钛源,通过盐酸调制的水热法制备出了具有棒状结构的金红石相纳米TiO2,并进一步进行高温氢化处理.采用X射线衍射(XRD),透射电镜(TEM),紫外-可见-近红外漫反射(UV-Vis-NIR DRS),电子顺磁共振(EPR)和表面光伏(SPS)等测试手段对样品进行表征,以气相乙醛和液相苯酚为目标污染物考察催化剂的光催化活性.结果表明:随着高温氢化处理时间的延长,TiO2样品的可见光吸收逐渐增强,其颜色逐渐由白色转变成灰色,这主要与引入的Ti3+/氧空位缺陷有关.表面光电压谱和羟基自由基测试表明,适当时间的氢化处理有利于光生电荷的分离.在光催化氧化降解气相乙醛和液相苯酚过程中,经适当时间氢化处理的样品表现出高的可见光催化活性.并且可见光催化活性的规律与紫外光下的是一致的.这是因为氢化处理后在导带底下方引入了缺陷能级,拓展了可见光响应.过度的氢化处理会在TiO2导带下方引入较低的缺陷能级,使光生电荷的复合加剧,导致光催化活性降低.     

LaCoO_3-TiO_2纳米管阵列的构筑及可见光光催化性能

TiO_2纳米管阵列具有较高的光催化活性,但可见光吸收弱,限制了其太阳能利用和环境应用。窄带隙的钙钛矿(ABO3)型氧化物能够吸收大范围波段的可见光,且稳定性高,但光催化活性低。本文首先采用溶胶-凝胶法合成了LaCoO_3纳米颗粒,然后利用电泳沉积技术将LaCoO_3纳米颗粒修饰于TiO_2纳米管阵列表面,构筑了LaCoO_3-TiO_2纳米管阵列。扫描电子显微镜(SEM)、透射电子显微镜(SEM)、X射线衍射(XRD)和X射线光电子能谱(XPS)的表征结果显示溶胶-凝胶法合成的纳米颗粒为LaCoO_3,其尺寸均匀,结晶度高,平均粒径约为100nm。LaCoO_3纳米颗粒与TiO_2纳米管阵列之间的结合力好。紫外可见吸收光谱(DRS)显示,随着电泳沉积时间的延长,LaCoO_3-TiO_2纳米管阵列的吸收带边逐渐红移700nm。可见光下光催化降解甲基橙(MO)的结果表明,电泳沉积15 min制得的LaCoO_3-TiO_2纳米管阵列对MO的光催化效率最高,其降解速率是相同条件下TiO_2纳米管阵列的4倍。光致发光光谱和电化学阻抗谱证实LaCoO_3纳米颗粒的负载有效地促进了光生电荷的分离和传输,可见光光催化活性明显增强。     

掺杂WO3的SiO2/TiO2的溶胶热液合成及光催化性能

采用溶胶-热液合成法制备了掺杂WO₃的SiO₂/TiO₂复合光催化剂,用X射线衍射、红外光谱、Zeta电位分析、BET和透射电镜对样品进行了表征,并以甲基橙降解评价了其光催化性能.结果表明:改性后的光催化剂表现出较高的光催化性能,WO₃和SiO₂不仅增加了锐钛矿TiO₂的稳定性,并阻止了TiO₂晶粒的聚集生长.     

TiO2/Bi2O3纳米复合体的制备及可见光催化产氢性能

首先采用相分离的水解-溶剂热法制备了Bi₂O₃纳米粒子,然后利用简单的湿化学法在Bi₂O₃表面负载不同比例的TiO₂纳米颗粒,进而得到TiO₂/Bi₂O₃纳米复合体。通过气氛调控的表面光电压谱(SPS)等测试表明,表面负载适量的TiO₂后能够提高Bi₂O₃光生电荷分离。可见光催化产氢和降解污染物测试结果进一步证明,表面负载适量的TiO₂后可显著提高其可见光催化活性,其中Ti/Bi摩尔比为7%时具有最高的光催化活性。这主要归因于TiO₂具有较为合适的导带能级位置,可以接收Bi₂O₃在可见光激发下所产生的高能级电子,从而抑制光生电子-空穴对复合,并且维持了高能级电子较高的还原能力。     

太阳光照射浮石负载二氧化钛降解氨氮废水

采用溶胶-凝胶法制备了Ti O_2,并使Ti O_2负载在浮石上制备Ti O_2/浮石光催化剂。用X射线荧光光谱(XRF)、电镜扫子显微描(SEM)和傅里叶红外光谱(FT-IR)表征浮石、Ti O_2及Ti O_2/浮石。在太阳光照射下,用Ti O_2/浮石处理模拟氨氮废水,以废水中氨氮降解率为标准,考察影响氨氮降解因素。结果表明,Ti O_2成功固定在浮石表面,负载率为3.71%;废水中氨氮降解率随太阳光照射时间、废水p H值、催化剂Ti O_2/浮石含量增加而增大。当初始氨氮浓度为500 mg/L、太阳照射180 min、废水p H=11、催化剂Ti O_2/浮石剂量为20 g/L时,氨氮降解率达82.0%,氨氮除去率86.8%,降解产物中未发现污染成分NO_2~-和NO_3~-产生。催化剂再生/催化3次,每次再生后氨氮降解率约下降10.0%。该方法快速、简单、低消耗和产生二次污染少,能有效地降解废水中的氨氮。     

SnO_2/TiO_2纳米管复合光催化剂的性能及失活再生

基于微波水热法和微乳液法合成SnO2/TiO2纳米管复合光催化剂.通过X射线衍射(XRD)、配有能量色散X射线光谱仪(EDX)的透射电镜(TEM)和电化学手段对光催化剂进行表征.以甲苯为模型污染物,考察光催化剂在紫外光(UV)和真空远紫外光(VUV)下的性能及失活再生.结果表明,SnO2/TiO2纳米管复合光催化剂形成三元异质结(锐钛矿相TiO2(A-TiO2)/金红石相TiO2(R-TiO2)、A-TiO2/SnO2和R-TiO2/SnO2异质结),促使光生电子-空穴对的有效分离,提高光催化活性.SnO2/TiO2表现出最佳的光催化性能,UV和VUV条件下的甲苯降解率均达100%,CO2生成速率(k2)均为P25的3倍左右.但由于UV光照矿化能力不足,中间产物易在催化剂表面累积.随着UV光照时间的增加,SnO2/TiO2逐渐失活,20 h后k2由138.5 mg·m-3·h-1下降到76.1 mg·m-3·h-1.利用VUV再生失活的SnO2/TiO2,过程中产生的·OH、O2-·、O(1D)、O(3P)、O3等活性物质可氧化吸附于催化剂活性位的难降解中间产物,使催化剂得以再生,12 h后k2恢复到143.6 mg·m-3·h-1.UV和VUV的协同效应使UV降解耦合VUV再生成为一种可持续的光催化降解污染物模式.     

Synthesis and photocatalytic activity of TiO2/conjugated polymer complex nanoparticles

A photocatalyst of nanometer TiO2/conjugated polymer complex was successfully synthesized and characterized by spectroscopic methods and photocatalytic experiments. The complex photocatalyst could be activated by absorbing both ultraviolet and visible light （λ = 190-800 nm）. Methylene blue （MB） could be degraded more efficiently on the complex photocatalyst than on the TiO2 under natural light. The conjugated polymer played a promoting role in the photocatalytic degradation of MB. The calcination temperature had an important effect in degradation of dye and could be summarized as 260℃ 〉 300 ℃ 〉 340 ℃ 〉 220 ℃ 〉 180 ℃.     

Synthesis of titania and titanate nanomaterials and their application in environmental analytical chemistry

TiO₂ nanoparticles and H₂Ti₂O₅·H₂O, Na₂Ti₂O₄(OH)₂ nanotubes were synthesized by solvothermal method and their applications in the degradation of active Brilliant-blue (KN-R) solution were investigated. The experimental results revealed that the synthesized TiO₂ nanoparticles had a good crystallinity and a narrow size distribution (about 4–5 nm); the obtained H₂Ti₂O₅·H₂O, Na₂Ti₂O₄(OH)₂ were tubelike products with an average diameter of 20–30 and 200–300 nm length. The three catalysts we synthesized had some hydroxyl groups and the maximum absorption boundaries of the samples were all red-shifted, which indicated the samples had a promising prospect in photocatalysis.

The results of the photocatalytic experiments indicated that the photocatalytic activity of the samples was: TiO₂ > H₂Ti₂O₅·H₂O > Na₂Ti₂O₄(OH)₂, which was in good accordance with the fact of FTIR and UV–vis absorption spectra. The formation mechanism of these nanostructures was also discussed.     

铋掺杂介孔二氧化钛的制备及光催化动力学

以介孔分子筛(KIT-6)为载体,采用溶液浸渍法合成了铋(Bi)掺杂的介孔二氧化钛(TiO₂)光催化剂。利用XRD、TEM、SEM、XPS、N₂吸附-脱附法和拉曼光谱法等技术手段对材料的结构和形貌进行表征。通过紫外-可见吸收光谱法考察了催化剂对罗丹明B光催化降解效率,进一步考察了Bi的掺杂量对光催化反应速率的影响,并对光催化降解动力学进行了初步研究。结果表明,Bi掺杂的介孔TiO₂具有较窄的孔径分布(3~4 nm),而且吸收范围扩展到可见光区,其光催化活性明显高于商品TiO₂(P25)。随之Bi掺杂量的提高,反应速率常数也增大,其光催化降解罗丹明B的反应均符合准一级动力学方程。