BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合光催化剂的制备及光催化性能研究

以Bi(NO_3)_3·5H_2O和NH_4VO_3为原料,控制水溶液介质p H及反应时间,采用水热合成法制备钒酸铋(BiVO_4)及其复合物(BiVO_4/Bi_6O_6(OH)_3(NO_3)_3).利用X-射线粉末衍射、扫描电子显微镜和紫外-可见漫反射吸收光谱等手段对制备的样品进行了物理表征,结果表明,在控制反应时间为1 h,介质p H值在1.14~9.01之间时,制备的样品为BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合物,当p H值增加至10.92时为纯BiVO_4;控制介质p H为7.17,反应时间在1~12 h之间时得到BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合光催化剂,反应时间为18 h时为纯BiVO_4.在可见光(λ≥400 nm)照射下,以有机染料罗丹明B(Rhodamine B,Rh B)为底物,研究不同条件制备的BiVO_4或者复合物为光催化剂的光催化特性,发现p H=7.17,水热反应12 h得到的催化剂(BiVO_4/Bi_6O_6(OH)_3(NO_3)_3)光催化降解活性高于对照制备的纯BiVO_4.同时在可见光照射下,BiVO_4/Bi_6O_6(OH)_3(NO_3)_3亦可以有效降解无色小分子2,4-二氯苯酚(2,4-Dichlorophenol,2,4-DCP),说明氧化过程涉及到光催化过程.分析BiVO_4/Bi_6O_6(OH)_3(NO_3)_3复合光催化剂对Rh B光催化降解过程中活性物种,表明在降解过程中主要涉及空穴和超氧氧化,O_2·~-起主要作用.     

K_8[Zn(H_2O)MnW_(11)O_(39)]/PANI/TiO_2复合材料的制备及光催化性能

采用直接合成法制备K_8[Zn(H_2O)Mn W_(11)O_(39)],以(NH_4)_2S_2O_8为氧化剂,通过化学氧化法将聚苯胺包覆在纳米Ti O_2颗粒表面制得PANI/Ti O_2,然后运用静电自组装法将K_8[Zn(H_2O)Mn W_(11)O_(39)]与PANI/Ti O_2复合成K_8[Zn(H_2O)Mn W_(11)O_(39)]/PANI/Ti O_2复合材料。运用IR、UV、XRD、XPS、SEM、N2吸附-脱附等分析方法对K_8[Zn(H_2O)Mn W_(11)O_(39)]/PANI/Ti O_2进行表征。利用K_8[Zn(H_2O)Mn W_(11)O_(39)]/PANI/Ti O_2为催化剂,研究其对孔雀石绿溶液的光催化降解性能。结果表明:紫外光照射下,孔雀石绿p H为2,浓度为20 mg/L,催化剂为10 mg时,脱色率可达93.66%。     

杂多钨酸盐/PANI/TiO_2三元复合催化剂的制备及光催化性能

以过硫酸铵为氧化剂,制备了复合光催化材料α-Si W11Ti/PANI/Ti O2。用UV-Vis、IR、XRD和SEM-EDS等测试手段对其结构及形貌等进行了表征。IR结果表明,复合后聚苯胺的IR振动峰发生红移。N2吸附-脱附显示产物为介孔材料,具有双孔结构,平均孔径约为20.07nm和26.69nm。以刚果红染料废水(15 mg/L)为探针反应,评价了其光催化性能,与一元催化剂Ti O2和二元催化剂/PAIN/Ti O2比较,三元催化剂Si W11Ti/PANI/Ti O2表现出更高的光催化降解性能,经30W紫外灯照射150min后,其降解率为92.44%。     

C/Fe-Bi_2WO_6光催化氧化诺氟沙星废水的效能及其机理

采用树脂碳化和水热两步法制备C/Fe-Bi_2WO_6光催化剂,对不同光催化剂光催化降解诺氟沙星溶液的去除效果进行对比研究。考察了条件因素对诺氟沙星(NOR)溶液在模拟太阳光下光催化氧化降解的影响规律。结果表明,在实验条件下,NOR光催化氧化降解符合L-H拟一级反应动力学模型,在NOR溶液初始浓度10 mg/L、溶液p H=7.0、催化剂用量0.75 g/L、H_2O_2浓度为200 mg/L、500 W氙灯照射60 min条件下,NOR完全分解,表观速率常数K_(app)为0.0751 min-1。采用分子荧光光谱法,对C/Fe-Bi_2WO_6光催化氧化去除NOR体系中羟基自由基生成规律进行研究,并推测了反应机理。结合LC-MS的分析结果,推测了NOR可能的降解路径和中间产物。     

铁锌柱撑膨润土催化剂的制备及其对甲基橙废水的光催化降解性能

采用微波辐照促进的溶胶浸渍法制备了铁锌柱撑膨润土催化剂;用制备的催化剂对甲基橙溶液在可见光照射下进行降解,探讨了铁负载量、H2O2质量浓度、溶液初始pH、反应时间和催化剂投加量对甲基橙降解率的影响,并考察了催化剂的重复利用性能.结果表明,在pH为3、H2O2质量浓度100mg/L、催化剂投加量1.5g/L、反应时间为2h条件下,甲基橙降解率可达97%.     

浮石负载壳聚糖吸附去除水中丙溴磷

通过浮石负载壳聚糖制备了吸附剂壳聚糖/浮石复合物,采用扫描电子显微镜(SEM)、热重分析(TGA)、元素分析、傅里叶红外光谱(FT-IR)、X射线衍射(XRD)和X射线荧光光谱(XRF)等技术手段表征了吸附剂性质,考察了吸附剂量、吸附时间、溶液pH值、离子强度和温度对该吸附剂吸附去除水中丙溴磷的影响,研究了再生吸附剂的吸附性能。结果表明,负载在浮石上的壳聚糖占吸附剂总量的8.69%;在p H值3.0~7.0内,壳聚糖/浮石对丙溴磷的吸附率大于90%;这种吸附剂对丙溴磷的吸附受溶液离子强度影响较小,随温度升高而稍微减小。在溶液温度25℃、pH=7.0、丙溴磷浓度40 mg/L、壳聚糖/浮石剂量为0.7 g/L和吸附平衡时间为90 min条件下,此吸附剂对丙溴磷最大吸附率为93.3%(最大吸附量为53.4 mg/g)。壳聚糖/浮石连续经过3次吸附/再生循环,每次循环对丙溴磷的吸附率下降约12%。可见壳聚糖/浮石通过吸附可有效地去除水中的农药丙溴磷。     

双配体仿酶催化剂的制备及其光催化降解水中对苯二酚

以天然氯化血红素和咪唑为原料,制备了咪唑轴向五配位型的双配体配合物,并将其负载于羟基功能化的纤维素磁微球表面。 通过紫外-可见分光光度、傅里叶变换红外光谱、透射电子显微镜、热重分析和振动样品磁强（VSM）对催化剂进行表征。 在模拟太阳光照射下,以水中溶解氧为氧化剂,考察了该催化剂降解模拟废水中有机污染物对苯二酚（HQ）的性能。 结果表明,在300 W氙灯照射下,当催化剂用量0.2 g/L、HQ初始浓度20 mg/L及pH值为6的条件下,6 h后HQ的降解率达到96.97%,催化剂重复使用5次后,降解率仍可达92%以上。同时对该催化剂光催化降解对苯二酚的机理进行了初步研究。     

旋转盘反应器中负载型Fe-TiO2光催化降解含酚废水

以溶胶凝胶法制备Fe掺杂TiO_2(Fe-TiO_2)并将其负载于旋转盘反应器的圆盘表面,用于降解苯酚质量浓度为100mg/L的废水。采用X射线衍射光谱、拉曼光谱、扫描电镜、紫外-可见漫反射光谱等分析手段对制备的催化剂进行了表征,并考察了掺杂量和焙烧温度对其催化性能的影响。结果表明,Fe~(3+)进入TiO_2晶格内部替代了Ti4+,引起晶体内部缺陷增加,拓宽了光响应范围,提高了纳米光催化剂的光催化活性。掺杂量0.5(wt)%和焙烧温度600℃时制备的负载型Fe-TiO_2催化剂具有较高催化活性,用于降解1L苯酚溶液,循环处理2h后苯酚的降解率可达75%,较纯TiO_2提高20%以上。     

介孔结构Na_(10)[α-SiW_9O_(34)]/TiO_2/Ag的合成及光催化性能研究

本文采用溶胶-凝胶法制备Na10[α-Si W9O34]/Ti O2/Ag复合材料。用IR、XRD、UV‐Vis漫反射光谱、SEM、ED-Mapping等方法进行了表征和分析。用N2吸附-脱附等温线考察了催化剂的比表面、孔径,表明产物为介孔材料。以标题化合物作为光催化剂催化降解亚甲基蓝,探讨催化剂用量、亚甲基蓝的初始浓度、溶液的p H值等条件对亚甲基蓝脱色率的影响,结果表明:催化剂加入量为1 mg·L-1、亚甲基蓝的初始浓度为5 mg·L-1,p H=2.0,脱色率达到94.7%。     

Cu(Ⅱ)/TiO_2/H_2O_2联合体系中甲基橙的太阳光催化降解

以钛酸四丁酯[Ti(OC4H9)4]为原料通过回流水解,制备了过渡金属Cu(Ⅱ)离子掺杂的TiO2光催化剂.通过TG DTA,IR,XRD对其进行了表征.结果表明:未经热处理的Cu(Ⅱ)/TiO2粉体为锐钛矿和板钛矿的混合晶型.在H2O2存在,太阳光照射下,甲基橙在该悬浮体系中迅速褪色降解,5min内降解率达90%以上.同时研究了pH值、H2O2浓度、甲基橙用量、光照条件、分散方式等对光催化剂活性的影响.     

C/Cr2O3/TiO2复合材料的制备及其光催化性能研究

本文以制革含铬革屑为原材料,基于矿物鞣剂复鞣的原理,将Ti(IV)均匀、稳定地负载到含铬革屑上,在氮气氛围下,经高温热解制备得到C/Cr₂O₃/TiO₂光催化剂,并研究了其对四环素(TC)的光催化降解效果及机理。结果表明,C/Cr₂O₃/TiO₂光催化剂具有明显的介孔结构,比表面积较大,为277.47 m²·g^-1,Cr₂O₃和TiO₂已实现复合并负载在生物炭(C)上。通过光催化降解发现,在模拟自然光照下,当催化剂用量为0.04 g,TC初始浓度为50 mg·L^-1,溶液pH为2时,TC的去除率可高达99.99%。结合自由基捕获实验发现,C/Cr₂O₃/TiO₂光催化剂对TC的降解作用主要依靠反应体系中产生的大量·O₂^-,·OH和h⁺。     

Keggin型铬取代的磷钨杂多阴离子/二氧化钛纳米膜光催化剂的制备及可见光催化性能

以钛酸四丁酯Ti(OC₄H₉)₄为TiO₂前驱体,Keggin型铬取代的杂多阴离子PW₁₁Cr为可见光活性组分,采用溶胶-凝胶提拉法在玻片表面制备了PW₁₁Cr/TiO₂纳米膜光催化剂,并用UV-Vis DRS、IR、XRD、SEM和TEM等技术手段对催化剂的光吸收性质、化学组成、晶相和表面结构形貌等进行了表征;讨论了膜中PW₁₁Cr和TiO₂相互作用的方式;以染料模型污染物RhB的可见光催化降解为探针,评估了PW₁₁Cr/TiO₂光催化剂的可见光催化活性,讨论了光催化反应机理,并与TiO₂的光催化反应机理进行了比较;考察了焙烧温度、PW₁₁Cr剂量和溶液pH值对光催化活性的影响;最后用RhB的循环降解实验评估了催化剂的光催化稳定性。 实验结果表明,PW₁₁Cr/TiO₂光催化剂对可见光有明显吸收,较低焙烧温度(100 ℃)下得到的膜为无定形结构,而较高焙烧温度(500 ℃)为纳晶结构;前者的光催化活性较高,在200 W金卤灯照射下降解10 μmol/L RhB,120 min的降解率为95%,4 h的COD去除率为72%;羟基自由基是导致RhB降解的主要氧活性物质;低的膜处理温度,高的PW₁₁Cr负载量和溶液酸性有利于提高PW₁₁Cr/TiO₂膜的光催化活性;经循环重复使用10次,PW₁₁Cr/TiO₂膜的光催化活性仅有较少损失。     

掺杂WO3的SiO2/TiO2的溶胶热液合成及光催化性能

采用溶胶-热液合成法制备了掺杂WO₃的SiO₂/TiO₂复合光催化剂,用X射线衍射、红外光谱、Zeta电位分析、BET和透射电镜对样品进行了表征,并以甲基橙降解评价了其光催化性能.结果表明:改性后的光催化剂表现出较高的光催化性能,WO₃和SiO₂不仅增加了锐钛矿TiO₂的稳定性,并阻止了TiO₂晶粒的聚集生长.     

SnO_2/TiO_2纳米管复合光催化剂的性能及失活再生

基于微波水热法和微乳液法合成SnO2/TiO2纳米管复合光催化剂.通过X射线衍射(XRD)、配有能量色散X射线光谱仪(EDX)的透射电镜(TEM)和电化学手段对光催化剂进行表征.以甲苯为模型污染物,考察光催化剂在紫外光(UV)和真空远紫外光(VUV)下的性能及失活再生.结果表明,SnO2/TiO2纳米管复合光催化剂形成三元异质结(锐钛矿相TiO2(A-TiO2)/金红石相TiO2(R-TiO2)、A-TiO2/SnO2和R-TiO2/SnO2异质结),促使光生电子-空穴对的有效分离,提高光催化活性.SnO2/TiO2表现出最佳的光催化性能,UV和VUV条件下的甲苯降解率均达100%,CO2生成速率(k2)均为P25的3倍左右.但由于UV光照矿化能力不足,中间产物易在催化剂表面累积.随着UV光照时间的增加,SnO2/TiO2逐渐失活,20 h后k2由138.5 mg·m-3·h-1下降到76.1 mg·m-3·h-1.利用VUV再生失活的SnO2/TiO2,过程中产生的·OH、O2-·、O(1D)、O(3P)、O3等活性物质可氧化吸附于催化剂活性位的难降解中间产物,使催化剂得以再生,12 h后k2恢复到143.6 mg·m-3·h-1.UV和VUV的协同效应使UV降解耦合VUV再生成为一种可持续的光催化降解污染物模式.     

Ti-MOF Derived N-Doped TiO2 Nanostructure as Visible-light-driven Photocatalyst

Nanostructured N-doped TiO₂ photocatalyst has been prepared via a new approach from Ti-based MOF[NH₂-MIL-125(Ti)] precursor. The success of N doping enhances light absorption and narrows the bandgap. Moreover, the as-prepared nanostructure is constructed with tiny nanoparticles and resembles a pie-like morphology inherited from the MOF, which accelerates electron transfer. Hence, as a photocatalyst for the degradation of methylene blue(MB) under visible light irradiation, the N-doped TiO₂(N-TiO₂) nanostructure shows higher photocatalytic activity with a reaction rate constant of 0.018 min^-1 than that of the TiO₂-P25 and TiO₂ under the visible light.     

铋掺杂介孔二氧化钛的制备及光催化动力学

以介孔分子筛(KIT-6)为载体,采用溶液浸渍法合成了铋(Bi)掺杂的介孔二氧化钛(TiO₂)光催化剂。利用XRD、TEM、SEM、XPS、N₂吸附-脱附法和拉曼光谱法等技术手段对材料的结构和形貌进行表征。通过紫外-可见吸收光谱法考察了催化剂对罗丹明B光催化降解效率,进一步考察了Bi的掺杂量对光催化反应速率的影响,并对光催化降解动力学进行了初步研究。结果表明,Bi掺杂的介孔TiO₂具有较窄的孔径分布(3~4 nm),而且吸收范围扩展到可见光区,其光催化活性明显高于商品TiO₂(P25)。随之Bi掺杂量的提高,反应速率常数也增大,其光催化降解罗丹明B的反应均符合准一级动力学方程。     

Heterostructured Nitrogen and Sulfur co-Doped Black TiO2/g-C3N4 Photocatalyst with Enhanced Photocatalytic Activity

Conventional titanium dioxide(TiO₂) photocatalyst could absorb only ultraviolet light due to its wide bandgap. In this paper, black TiO₂ with narrow bandgap was prepared by introducing oxygen vacancies. Meanwhile, nitrogen(N) and sulfur(S) elements were doped to further broaden the visible light response range of TiO₂(NS-BT), and then heterostructured N,S-doped black TiO₂/g-C₃N₄(CN/NS-BT) was successfully constructed by easily accessible route. The formation of CN/NS-BT heterojunction structure increased the generation and separation efficiency of photogenerated electron-hole pairs, as well as accelerated the transfer rate of the carriers. The as-prepared CN/NS-BT exhibited excellent photocatalytic performance towards the degradation of Rhodamine B(RhB) under visible light irradiation with satisfactory stability. The apparent reaction rate constant of CN/NS-BT(0.0079) was 15.8-fold higher than that of commercial P25(0.0005). The structure, morphology, chemical composition and optical properties of the as-prepared CN/NS-BT were characterized by various analytical methods, and possible photocatalytic enhancement mechanism was proposed. Overall, CN/NS-BT composites look promising as photocatalytic material for future environmental treatment.     

微波辅助快速制备2D/1D ZnIn2S4/TiO2 S型异质结及其光催化制氢性能

The threat and global concern of energy crises have significantly increased over the last two decades. Because solar light and water are abundant on earth, photocatalytic hydrogen evolution through water splitting has been considered as a promising route to produce green energy. Therefore, semiconductor photocatalysts play a key role in transforming sunlight and water to hydrogen energy. To date, various photocatalysts have been studied. Among them, TiO₂ has been extensively investigated because of its non-toxicity, high chemical stability, controllable morphology, and high photocatalytic activity. In particular, 1D TiO₂ nanofibers (NFs) have attracted increasing attention as effective photocatalysts because of their unique 1D electron transfer pathway, high adsorption capacity, and high photoinduced electron–hole pair transfer capability. However, TiO₂ NFs are considered as an inefficient photocatalyst for the hydrogen evolution reaction (HER) because of their disadvantages such as a large band gap (~3.2 eV) and fast recombination of photoinduced electron–hole pairs. Therefore, the development of a high-performance TiO₂ NF photocatalyst is required for efficient solar light conversion. In recent years, several strategies have been explored to improve the photocatalytic activity of TiO₂ NFs, including coupling with narrow-bandgap semiconductors (such as ZnIn₂S₄). Recently, microwave (MW)-assisted synthesis has been considered as an important strategy for the preparation of photocatalyst semiconductors because of its low cost, environment-friendliness, simplicity, and high reaction rate. Herein, to overcome the above-mentioned limiting properties of TiO₂ NFs, we report a 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction synthesized through a microwave (MW)-assisted process. Herein, the 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction was constructed rapidly by using in situ 2D ZnIn₂S₄nanosheets decorated on 1D TiO₂ NFs. The loading of ZnIn₂S₄ nanoplates on the TiO₂ NFs could be easily controlled by adjusting the molar ratios of ZnIn₂S₄ precursors to TiO₂ NFs. The photocatalytic activity of the as-prepared samples for water splitting under simulated solar light irradiation was assessed. The experimental results showed that the photocatalytic performance of the ZnIn₂S₄/TiO₂ composites was significantly improved, and the obtained ZnIn₂S₄/TiO₂ composites showed increased optical absorption. Under optimal conditions, the highest HER rate of the ZT-0.5 (molar ratio of ZnIn₂S₄/TiO₂= 0.5) sample was 8774 μmol·g^-1·h^-1, which is considerably higher than those of pure TiO₂ NFs (3312 μmol·g^-1·h^-1) and ZnIn₂S₄nanoplates (3114 μmol·g^-1·h^-1) by factors of 2.7 and 2.8, respectively. Based on the experimental data and Mott-Schottky analysis, a possible mechanism for the formation of the S-scheme heterojunction between ZnIn₂S₄ and TiO₂ was proposed to interpret the enhanced HER activity of the ZnIn₂S₄/TiO₂heterojunctionphotocatalysts.      

半导体复合CdS/TiO2催化剂改性及冷冻-光催化组合方法应用的初步研究

采用溶胶-凝胶法制备多孔氧化钛,并耦合CdS,制备多孔耦合CdS/TiO₂催化剂.煅烧温度为700℃,CdS掺杂比例为3%时,催化剂性能较优.以太阳光为光源,考查了溴氨酸初始浓度对其降解效果的影响,并采用冷冻-光催化组合方法对较高浓度的溴氨酸废水的处理进行了初步研究.浓度为500 mg/L的溴氨酸模拟废水(其中氯化钠质量浓度为500 mg/L)经冷冻后,当成冰率为70%时,体系中冰层的Na⁺含量、总有机碳(TOC)和吸光度分别由209.88 mg/L,208.90 mg/L和8.120降至19.06 mg/L,24.80 mg/L和0.638.使用多孔耦合催化剂对该冰层融水光降解,光照6 h,褪色率和TOC去除率分别达到100%和87.04%.     

Synthesis and photocatalytic activity of TiO2/conjugated polymer complex nanoparticles

A photocatalyst of nanometer TiO2/conjugated polymer complex was successfully synthesized and characterized by spectroscopic methods and photocatalytic experiments. The complex photocatalyst could be activated by absorbing both ultraviolet and visible light （λ = 190-800 nm）. Methylene blue （MB） could be degraded more efficiently on the complex photocatalyst than on the TiO2 under natural light. The conjugated polymer played a promoting role in the photocatalytic degradation of MB. The calcination temperature had an important effect in degradation of dye and could be summarized as 260℃ 〉 300 ℃ 〉 340 ℃ 〉 220 ℃ 〉 180 ℃.