手性含硫恶唑硼烷催化芳酮不对称还原反应的量子化学研究

用HF方法在6-31G^*基组下,对手性含硫恶唑硼烷催化苯乙酮不对称还原反应进行了量子化学从头算研究。还原反应经历了催化剂-硼烷加合物、催化剂-硼烷-酮加合物、催化剂-烷氧基硼烷加合物的生成以及催化剂-烷氧基硼烷加合物的离解过程。催化剂-硼烷加合物、催化剂-硼烷-酮加合物和催化剂-烷氧基硼烷加合物的生成分别为放热、吸热、放热过程;催化剂-烷氧基硼烷加合物离解成催化剂烷氧基硼烷为吸热过程。催化剂-硼烷-酮加合物和催化剂-烷氧基硼烷加合物都存在四种稳定的结构。最有利于氢转移的催化剂-硼烷-酮加合物结构是次低能量结构,并且具有扭曲的船形结构。催化剂-烷氧基硼烷加合物含有一个B-O-B-N四元环,尽管四元环有较大的张力,但加合物仍有较高的稳定性。     

助催化剂对Fe1-xO基氨合成催化剂还原性能的影响

当助催化剂存在是地，Ｆｅ１－ｘＯ基催化剂的还原性能明显优于Ｆｅ３Ｏ４基催化剂，其原因是铝、钾、钙的氧化物对催化剂母体相Ｆｅ１－ｘＯ和Ｆｅ３Ｏ４还原性能的影响不同。由于Ａｌ＾３＋大量地进入Ｆｅ３Ｏ４的晶格而强烈地阻止Ｆｅ３Ｏ４的还原，只有少量的Ａｌ＾３＋能进入Ｆｅ１－ｘＯ晶格，因此对Ｆｅ１－ｘＯ的还原影响很小；     

高温煤气中氨的脱除：Ⅰ.氨催化分解催化剂的筛选

制备和筛选了１２ 种氨催化分解催化剂,所选催化剂包括Ｃｕ － Ｍｎ 基脱硫剂,Ｚｎ－ Ｔｉ 基脱硫剂,Ｆｅ 基催化剂及Ｎｉ 基催化剂四大类,其中Ｎｉ－２ 催化剂及Ｎｉ－ ３ 催化剂具有较高的转化率。然后对Ｎｉ－３ 催化剂进行了寿命试验,１００ｈ 内其活性基本维持不变;耐硫性实验表明Ｎｉ－３ 催化剂具有一定的耐硫性能,因而它是所选的最优催化剂     

固载超强酸催化剂制备及催化合成乙酸正丁酯的研究

研究了把稀土硫酸盐,分别固载于人工沸石、活性炭和强酸型阳离子树脂作为酯化催化剂,从中选出了较好的酯化催化剂－强酸型阳离子树脂固载稀土催化剂,此催化剂用于合成乙酸正丁酯,产率达到97.24%,并对催化剂的催化性能进行了讨论。     

SO42-/Zr-ZSM-5 超强酸催化剂的制备和表征

以硅溶胶和氧氯化锆为硅源和锆源，采用水热合成的方法制得具有ZSM-5结构的Zr-Si分子筛；用0.5mol/L的硫酸处理该分子筛，并在550℃焙烧，制得具有ZSM-5结构的SO4^2-/ZrO2-SiO2分子筛型的固体超强酸。采用XRD、SEM、TG、IR、NH3-PHD和指示剂法对其结构和酸性进行表征。结果表明，该SO4^2-/ZrO2-SiO2具有ZSM-5结构和超强酸性，其酸强度大于-13.75，且具有良好的热稳定性。     

SO_4~(2-)/ZrO_2超强酸催化合成邻苯二甲酸二辛酯初探

初步探索了SO42-／ZrO2超强酸作为合成邻苯二甲酸二辛酯（DOP）催化剂的催化性能．详细考察了反应温度、催化剂用量和反应时间对邻苯二甲酸酐转化率的影响．结果表明，反应温度低于428K时，温度的升高显著增加邻苯二甲酸酐的转化率，反应温度高于428K时，温度的升高对转化率的影响较小；催化剂用量为邻苯二甲酸酐的3％时，邻苯二甲酸酐的转化率即可达到93．6％，表明SO42-／ZrO2超强酸催化剂具有很高的催化活性；催化剂使用20小时后，转化率由958％下降到86．5％，表明初步制得的催化剂稳定性还较差；用SO42-／ZrO2超强酸催化剂会成的DOP为无色透明油状液体。其品质明显优于用对甲苯磺酸或液体改作催化剂时的产品。     

Highly active copper-based catalyst for atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) generally requires a catalyst/initiator molar ratio of 0.1 to 1 and catalyst/monomer molar ratio of 0.001 to 0.01 (i.e., catalyst concentration: 1000-10,000 ppm versus monomer). Herein, we report a new copper-based complex CuBr/N,N,N',N'-tetrakis(2-pyridylmethyl)ethylenediamine (TPEN) as a versatile and highly active catalyst for acrylic, methacrylic, and styrenic monomers. The catalyst mediated ATRP at a catalyst/initiator molar ratio of 0.005 and produced polymers with well-controlled molecular weights and low polydispersities. ATRP occurred even at a catalyst/initiator molar ratio as low as 0.001 with copper concentration in the produced polymers as low as 6-8 ppm (catalyst/monomer molar ratio = 10(-5)). The catalyst structures were studied by X-ray diffraction and NMR spectroscopy. The activator CuIBr/TPEN existed in solution as binuclear and mononuclear complexes in equilibrium but as a binuclear complex in its single crystals. The deactivator CuIIBr2/TPEN complex was mononuclear. High stability and appropriate KATRP (ATRP equilibrium constant) were found crucial for the catalyst working under high dilution or in coordinating solvents/monomers. This provides guidance for further design of highly active ATRP catalysts.     

镧对固体超强酸SO4^2-／TiO2／甜交联膨润土的改性研究

采用镧对固体超强酸SO4^2-／TiO2／铝交联膨润土（SO4^2-／TiO2／Al—PILC）进行改性，制备了La-SO4^2-／TiO2／Al—PILC稀土超强酸，并采用XRD、低温N2吸附法及吡啶吸附红外等方法对其进行了结构、表面性能及酸性的表征。实验结果表明，镧引入SO4^2-／TiO2／Al—FILC超强酸，对TiO2锐钛矿晶相的形成没有影响，但对锐钛矿晶相向金红石相的转变有抑制作用，镧的引入使催化剂的酸强度及酸中心的数量有所增加，镧能有效地减少催化剂表面SO4^2-的流失量，从而提高催化剂的活性稳定性。     

Kinetics of synthesizing polymer-supported quaternary ammonium catalysts

This study attempted to synthesize the optimum quaterary ammonium poly(styrene-co-methylstyrene) catalyst using the combinatorial chemistry method. The catalyst was synthesized by a mix-split method. A phase-transfer catalyst library with 25 kinds of polystyrene-supported quaternary ammonium salt catalyst was the the result of the reaction of five kinds of chloromethylated crosslinked polystyrene with five tert-amines. The allylation of phenol and the oxidation of benzyl alcohol were used as the probing reaction to screen out the most active catalyst for the reaction using the iterative deconvolution method. The screening conditions included teritary amine and organic solvent. The structure of the most active catalyst in the allylation of phenol shows 20 mol % ring substitution and 0.177-0.25-mm pellet size activated with trihexylamine. For oxidation of benzyl alcohol, the reaction conditions of the most active catalyst included a resin of 20% ring substitution and pellet size of 0.177-0.25 mm, activated with triethylamine reacting in an organic solvent of n-hexane.     

Preparation, Characterization and Catalytic Properties of S2O2-8/ZrO2 Supported by Tungsten Carbide

A WC-supported S2O2-8/ZrO2(PSZ) catalyst was prepared and characterized by means of XRD, BET, FTIR and XPS. The isomerization of n-pentane over the catalyst was investigated as well. The results show that the skeletal isomerization and the crack of n-pentane proceed simultaneously on WC-supported S2O2-8/ZrO2 catalyst. The addition of tungsten carbide showed a significant enhancement in the activity and stability of the catalyst for n-pentane isomerization. The catalyst showed evidently a better activity than S2O2-8/ZrO2 supported by Pt and WO3. The results can be interpreted by the existence of the tungsten oxycarbide compound(WCxOy) with carbidic, oxide and acidic sites.     

Efficient catalyst turnover in the phosphitylation of alcohols with phosphoramidites

We report a method for catalytic phosphitylation utilizing phosphoramidites. Traditionally, this reaction is inefficient unless an excess of catalyst is present due to catalyst deactivation by an amine by-product. Isocyanate additives have been evaluated for scavenging the amine to facilitate catalyst turnover. A variety of alcohols and phosphoramidites were screened with 5 mol % catalyst. In the presence of additive, 83-97% conversion was achieved in contrast to 7-31% conversion without additive.     

Preparation of mesoporous carbon from commercial activated carbon with steam activation in the presence of cerium oxide

Mesoporous carbon was prepared from the commercial activated carbon by steam activation with cerium oxide as catalyst. Steam activation with a catalyst loading of 0.5-2.0 wt% at 680-870 degrees C was examined. The surface area and pore size were evaluated by nitrogen adsorption at 77 K, and the structure of cerium oxide was characterized by XRD, XPS, and TEM. The results showed that the catalyst promoted the development of a mesopore at lower temperature (680-740 degrees C), and the mesopore was concentrated around 4-10 nm. The noncatalytic activation was advantageous in mesopore development and the catalyst would restrict the formation of mesopores at high temperature (800-870 degrees C). Higher loading of cerium oxide and higher activation temperature caused the aggregation of cerium oxide and then resulted in scattered pore size distribution.     

甲烷氧化偶联Mn_2O_3-Na_2WO_4/SiO_2催化剂——Ⅲ.高温(700—800℃)XRD和XPS研究

在本工作的研究报导Ⅰ和Ⅱ(见本期477页和481页)中,已对Mn_2O_3-Na_2WO_4/SiO_2催化剂活性相的表面分散状态、表面氧种和表面结构进行了详细表征。但甲烷氧化偶联反应在高温(700—800℃)下进行。本文进一步对该催化剂在此反应高温下的XRD和XPS研究表明,其表面状态较室温下有显著变化,结合前文的室温下表征结果,使我们对高温反应条件下该催化剂组分间协同作用、表面活性氧种和活性位结构性质有了进一步的理解,并有可能对其甲烷催化活化机理进行较为深入的探讨。     

Modular synthesis of optically active lactones by Ru-catalyzed asymmetric allylic carboxylation and ring-closing metathesis reaction

A new synthetic route to optically active unsaturated γ- and δ-lactones has been demonstrated via asymmetric allylic carboxylation with a planar-chiral Cp'Ru catalyst and ring-closing metathesis reaction with a Grubbs II catalyst, and successfully applied to the enantioselective synthesis of (R)-(-)-massoialactone.     

Preparation and Catalytic Activity of SO42-/TiO-La2O3 in Synthesis of Butyl Butyrate

Butyl butyrate is a very important compound, which is transparent liquid and has the pear,apple flavor. Natural exist is in the fruit, such as apple, pear, banana, grape and strawberry, etc.Primarily used for to prepare the edible spice and is also widely used in industrial intermediate product, solvent and synthetic perfumery. Until now, there are many methods to synthesize it.Conventionally H2SO4 was reported, but it causes many problems, such as the erosion of equipment,easily causes the vice-reaction, difficulty for after-treatment, environment pollution etc. A new environmentally friendly catalyst, SO42-/TiO2-La2O3 was prepared. And catalytic activity of catalyst in esterification of n-butanoic acid and n-butyl alcohol with SO42-/TiO2-La2O3 as catalyst has been no report up to now. Therefore, studying on the synthetic catalyst has theoretical and practical significances. The catalytic activity of catalyst in esterification of n-butanoic acid and n-butyl alcohol was measured.In this paper, we fast reported the preparation of SO42-/riO2-La2O3 and discussed the factors influencing the synthesis catalyst. The catalyst rare earth solid superacid SO42-/TiO2-La2O3 was The precipitate was filtered and washed thoroughly with distilled water until chloride ions were free.furnace at 480 ℃ for 3 h, and finally stored in a desiccator until use.The factors influencing the synthesis were discussed and the best conditions were found out. The experiment indicated that this catalyst has the following advantage. The amount of catalyst was little and getting high yield, its product has a good quanlity and is favour of reducing erosion of equipment, avoiding environment pollution. The optimum conditions are: molar ratio of n-butanoic acid to n-butyl alcohol was 1:1.5, the quantity of catalyst was equal to 1.5% of feed stocks, the reaction temperature was 93-114 ℃, and the reaction time was 1.0 h. Rare earth solid superacid SO42-/TiO2-La2O3 is an excellent catalyst for synthetizing butyl butyrate and its yield can reach over 90.0%.A good catalyst should be able to be used repeatedly. The reusing of the catalyst was studied. We found that the catalytic activities of our catalyst are almost unchanged after it had been used five times. From the above results and discussion, we can see that the synthesis of n-butyl butyrate by SO42-/TiO2-La2O3 instead of H2SO4 has a great prospect of application. It has a good applied foreground.     

Highly active Pd containing EMT zeolite catalyst for indirect oxidative carbonylation of methanol to dimethyl carbonate

Palladium containing EMT zeolite catalyst(Pd/EMT) was prepared and used for the indirect oxidative carbonylation of methanol to dimethyl carbonate(DMC).The EMT zeolite was employed as a new catalyst support and compared with the conventional Pd containing FAU zeolite catalyst(Pd/FAU).The Pd/EMT in contrast to the Pd/FAU catalyst exhibited high intrinsic activity with the turnover frequency of 0.25 s^-1 vs.0.11 s^-1.The Pd/EMT catalyst showed high CO conversion of 82% and DMC selectivity of 79%,that maintained for at least 130 h,while the activity of the Pd/FAU catalyst rapidly deteriorated within 12 h.The enhanced interactions between Pd and EMT zeolite inhibited the sintering of palladium clusters and maintained the Pd2+ active sites in the Pd/EMT catalyst.The stabilization of the mono-dispersed Pd clusters within the EMT zeolite is paramount to the excellent performance of the catalyst for the indirect oxidative carbonylation of methanol to DMC.     

用双重孔模型计算变换催化剂内扩散效率因子

本文将双重孔模型应用于WB～2、B109变换催化剂多组分反应系统内扩散效率因子的计算,并与平行交联孔模型进行比较。对WB-2加压变换催化剂用双重孔模型计算,计算值与实验值相对偏差在3.86%～53.94%;对B109变换催化剂,计算值与实验值偏差在-28.24%～-3.31%。     

Product oriented oxidative bromination of methane over Rh/SiO_2 catalysts

Rh/SiO2 was prepared for the oxidative bromination of methane. The catalyst was prepared by calcination at different temperatures and for different times to obtain catalysts with different specific surface areas for the purposes of producing either CH3Br or CH3Br and CO. It was found that the catalyst having a low specific surface area (calcined at relatively high temperature) favors the selective oxidation of methane to prepare CH3Br, while the catalyst having a high specific surface area favors the deeper partial oxidation of methane, which is good for CH3Br and CO preparation.The 650 h on stream life-time test revealed that the catalytic performance of the 0.4Rh/SiO2-900-10 catalyst was excellent.Both methane conversion and CH3Br selectivity kept increasing trends during the life-time test.No matter how serious was the Rh leaching during the reaction,the 0.4Rh/SiO2-900-10 catalyst did not deactivate at all.     

镝对固体超强酸催化剂ZrO2-Dy2O3/SO42--HZSM-5的酸性和稳定性的影响

合成了固体超强酸催化剂ＺｒＯ２－Ｄｙ２Ｏ３／ＳＯ４＾２－,并将其负载于分子筛ＨＺＳＭ－５上,制成复合型固体超强酸催化剂ＺｒＯ２－Ｄｙ２Ｏ３／ＳＯ４＾２－ＨＺＳＭ－５）以下简称催化剂ＺＤＳＨ）,采用Ｈａｍｍｅｔｔ批示剂法,吸附吡淀的ＴＰＤ法,考察催化剂ＺＤＳＨ的酸强度及其分布;通过热重分析（ＴＧＡ）、差热分析（ＤＴＡ）方法,考察镝对催化剂ＺＤＳＨ稳定性的作用;运用红外光谱（ＩＲ）法,分析催化剂ＺＤＳ     

载体对合成气制甲烷镍基催化剂性能的影响

考察了A12O3-1,Al2O3-2和SiO2负载的Ni基催化剂上合成气制甲烷的反应活性和稳定性.结果表明,Ni/Al2O3-2和Ni/SiO2催化剂表现出较高的催化活性和稳定性,而Ni/Al2O3-1催化剂稳定性极差.采用X射线衍射、透射电镜、程序升温还原、N2吸附-脱附和热重分析等技术对催化剂进行了表征.结果显示,...