悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

高固含量微乳液聚合的研究进展

微乳液聚合能够制备透明稳定的微胶乳,在涂料、催化及药物输送等领域具有许多潜在的应用.本文综述了高固含量微乳液聚合的研究现状,主要介绍了两类方法:高效乳化剂体系的应用和聚合工艺的改进,并对今后的发展方向进行了展望.     

新型乳液聚合制备疏松PMMA树脂及成粒机理

采用以水相为分散相、甲基丙烯酸甲酯 (MMA) 环己烷混合物为连续相的新型乳液聚合制备PMMA树脂 .发现 ,在未加乳化剂和加入少量Tween2 0乳化剂时 ,均可制备由初级粒子凝聚而成、无明显皮膜结构的疏松PMMA粒子 ,初级粒子粒径小于环己烷存在下MMA悬浮聚合得到的PMMA粒子的初级粒子 .根据聚合体系相构成、PMMA在MMA 环己烷混合液的溶解性及PMMA粒子粒径分布和形态的演变 ,提出了在分散水滴内乳液聚合形成初级粒子 生长 凝聚的新型乳液聚合成粒机理     

超声辐照引发MMA微乳液聚合

研究了超声波引发甲基丙烯酸甲酯(MMA)的微乳液聚合.辐照40min时单体转化率高达90%.透射电镜观察发现,PMMA微乳液平均粒径为36.5nm,粒径分布窄,表明超声波引发是制备PMMA微乳液的有效方法.采用分光光度计对微乳液聚合过程中乳胶粒的形成和大小进行了间接表征,研究了超声功率输出、乳化剂、助乳化剂、单体和引发剂对MMA微乳液聚合的影响.     

含C60聚苯乙烯微球的制备及光电导性能研究

目前,多功能、高性能聚合物微球的合成及应用已成为研究热点.制备聚合物微球的方法有乳液聚合法、分散聚合法、无皂乳液聚合法、超微乳液聚合法和悬浮聚合法等.制备微米级微球通常采用乳液聚合法和分散聚合法.     

聚甲基丙烯酸甲酯/聚甲基丙烯酸-2-羟乙酯复合微球的合成及药物吸放性能

采用在甲基丙烯酸甲酯（MMA）悬浮聚合过程中滴加甲基丙烯酸-2-羟乙酯（HEMA）乳液聚合组分的悬浮-乳液耦合聚合方法,制备了大粒径聚甲基丙烯酸甲酯／聚甲基丙烯酸-2-羟乙酯（PMMA／PHEMA）复合微球。PMMA／PHEMA复合微球表面以HEMA乳液聚合物为主,且具有微孔结构。PMMA／PHEMA复合微球在水和苄醇中的平衡溶胀率大于PMMA微球。PMMA／PHEMA复合微球48h异丁苯丙酸负载百分比为35．6％,PMMA为27．6％。在磷酸盐缓冲液中释放时间达到360h,释放量占负载总量的82％;而PMMA微球的释放时间为216h,释放量仅占负载总量的60％。     

MMA接枝改性PVC/CaCO3纳米复合材料的力学性能

采用熔融共混法制备PMMA接枝改性纳米CaCO3增韧PVC（PVC/CaCO3）复合材料,并研究了复合材料的力学性能.结果表明,通过表面PMMA的接枝改性,可以显著提高纳米CaCO3增韧聚氯乙烯复合材料的拉伸强度和拉伸模量,在纳米CaCO3颗粒表面PMMA包覆层厚度为2nm时,复合材料的拉伸强度和拉伸模量达到极大值.对比于未处理纳米CaCO3和钛酸酯偶联剂处理纳米CaCO3,PMMA接枝改性纳米CaCO3增韧PVC复合材料的拉伸强度得到较大幅度提高.SEM显示,经过PMMA接枝改性后的碳酸钙在PVC基体中分散均匀,与基体界面结合良好.     

超浓乳液聚合制备PU/PS的SIPN粉状树脂研究

将聚氨酯予聚体 (PU ) 苯乙烯 (St)的复合体系 ,用超浓乳液聚合方法制备了半互穿聚合物网络(SIPN)复合聚合物 ,得到了用聚氨酯予聚体改性的聚苯乙烯 (PU/PS)SIPN粉状树脂 .研究了分散相的比例(α)和聚合温度对聚合稳定性及聚合转化率 -时间的关系 ;测定了聚合物胶乳粒子的大小、形态 ,玻璃化温度 ,动态力学性能等 .结果表明 ,超浓乳液聚合较之本体聚合具有较高的聚合速率 ,容易控制所制备的胶乳粒径 ,能够制得PU/PS复合聚合物的SIPN粉状树脂 .该粉状树脂便于加工 ,具有良好的强韧性 ,有利于扩大应用     

无皂乳液聚合法制备聚甲基丙烯酸甲酯包覆厚度可控的纳米核-壳二氧化硅微球

用改进的Stöber法和无皂乳液聚合法制备窄分布的二氧化硅/PMMA核-壳纳米微球. 用改进的Stöber法将3-乙氧基甲基丙烯酸丙基硅烷(MPS)修饰在纳米的二氧化硅表面后, 用无皂乳液聚合法制备核-壳纳米微球. 该法简单有效且得到厚度均匀的聚合物包覆层. 随着单体MMA用量的增加, 用动态光散射法测量, PMMA壳层的厚度从6.4 nm增加到96.3 nm. 热重分析表明, PMMA的含量从22.25%增加到93.41%. 扫描电子显微镜和透射电子显微镜结果表明, 得到的是包覆良好、表面光滑的核-壳无机/聚合物纳米微球.     

聚甲基丙烯酸甲酯接枝多壁碳纳米管的制备及表征

采用原位聚合的方法,分别在本体及超临界CO2介质中将聚甲基丙烯酸甲酯(PMMA)接枝到多壁碳纳米管(MWNTs)表面,通过GPC、拉曼光谱、TGA等手段对样品进行表征.聚合产物的GPC结果表明,体系中的PMMA存在游离和接枝两种状态;拉曼光谱中峰的红移以及D峰与G峰强度比值的增加证明PMMA与MWNTs之间存在化学键作用;TGA结果表明PMMA在本体和超临界CO2中的接枝率分别为39 %和27%.     

聚氯乙烯/纳米水滑石复合材料的形态与力学性能

对由原位悬浮聚合制备的聚氯乙烯(PVC)纳米水滑石复合树脂加工得到的纳米复合材料的形态和力学性能进行了研究,并与直接熔融加工得到的PVC纳米水滑石复合材料进行比较.发现由前一方法得到的PVC纳米水滑石复合材料中纳米水滑石的分散性明显优于由后一方法得到的PVC纳米水滑石复合材料,水滑石以初级粒子形式存在,分散良好,无明显团聚体;与之对应,由前一方法得到的PVC纳米水滑石复合材料的力学性能也明显优于由后一方法得到的PVC纳米水滑石复合材料,当纳米水滑石含量小于5wt%时,复合材料的杨氏摸量、拉伸强度和缺口冲击强度均随水滑石含量增加而增大;纳米水滑石的引入可显著提高复合树脂的热稳定性;PVC纳米水滑石复合材料的储能和损耗模量略大于纯PVC材料,而损耗因子和玻璃化温度变化不大.     

本体聚合制备Sm(OPr~i)(TTA)_2/PMMA光致发光材料

合成了(异丙氧基)二(α-噻吩甲酰三氟丙酮基)钐[Sm(OPri)(TTA)2]配合物,并通过本体聚合制备Sm(OPri)(TTA)2/PMMA光致发光材料,采用IR1、H-NMR、XRD、DMTA、FS、ESEM对其进行表征.结果表明,Sm-(OPri)(TTA)2/PMMA在396 nm波长激发下在562、598、644 nm处发射很强的Sm3+离子4G5/2→6H5/2,4G5/2→6H7/2,4G5/2→6H9/2跃迁的特征荧光,其发光强度与Sm(TTA)3/PMMA相当;其储能模量E′、玻璃化温度Tg和粘流温度Tf均比PMMA有所提高;Sm(OPri)3/PMMA形成类似交联结构聚合物,而Sm(OPri)(TTA)2/PMMA为线型无定型结构聚合物.     

Polyethylene-Montmorillonite Nanocomposites: Preparation,Characterization and Properties

Polyethylene(PE)/clay nanocomposites have been successfully prepared by in situ polymerization with an intercalation catalyst titanium-montmorillonite (Ti-MMT) and analyzed by X-ray diffraction analysis (XRD), Fourier transform infrared analysis (FT-IR), Transmission electron microscopy (TEM), differentail scanning calorimetry (DSC), thermal gravimetric analysis (TGA) and tensile testing. XRD and TEM indicate that the clay is exfoliated into nanometer size and disorderedly dispersed in the PE matrix, and the PE crystallinity of PE/clay nanocomposite declines to 15∼30%. Compared with pure PE, PE/clay nanocomposites behave higher thermal, physical and mechanical properties; the layer structure of the clay decreases the polymerization activity and produce polymer with a high molecular weight. For PE/clay nanocomposites, the highest tensile strength of 33.4 MPa and Young's modulus of 477.4 MPa has been achieved when clay content is 7.7 wt %. The maximum thermal decomposition temperature is up to 110 °C higher, but the thermal decomposition temperature of the PE/clay nanocomposites decreases with the increases of the clay contents in the PE matrix.     

Synthesis,characterization of layered double hydroxide‐poly(methylmethacrylate) graft copolymers via activators regenerated by electron transfer for atom transfer radical polymerization and its effect on the performance of poly(lactic acid)

Layered double hydroxide‐poly(methylmethacrylate) (LDH‐PMMA) graft copolymers were prepared via activators regenerated by electron transfer for atom transfer radical polymerization. The results showed that the hydrophobicity of LDH‐PMMA was improved by the incorporation of hydrophilic groups. Moreover, poly(lactic acid) (PLA)/LDH‐PMMA nanocomposites were prepared by melt blending to enhance the performances of PLA. The crystallization and mechanical properties of the PLA/LDH‐PMMA nanocomposites were studied by differential scanning calorimetry, tensile testing, and polarized optical microscopy, respectively. Results of mechanical testing showed that the tensile strength, elongation at break, and impact strength of PLA/LDH‐PMMA nanocomposites were increased by 5.64%, 37.95%, and 49.70%, respectively, compared with PLA. The differential scanning calorimetry results indicated that LDH‐PMMA eliminated the cold crystallization of PLA matrix and improved the crystallinity of PLA by 37.26%. The polarized optical microscopy of PLA/LDH‐PMMA nanocomposites demonstrated that LDH‐PMMA increased the crystallization rate of PLA. It was also found that the rheological behaviors of the PLA nanocomposites were significantly enhanced. Based on these results, a new choice for modified LDHs was provided and used as a nucleating agent to improve the properties of PLA.     

非水凝胶原位聚合法制备三异丙氧基钕/PMMA杂化材料的研究

通过三异丙氧基钕直接掺入MMA单体 ,迅速形成凝胶后进行原位聚合的方法制得三异丙氧基钕 /PMMA杂化材料 ,采用IR、TG、WAXD、DMTA、SEM等手段对其进行表征 .结果表明 ,三异丙氧基钕与MMA中的羰基因配位并导致交联形成了交联网状结构的杂化材料 .与PMMA相比 ,这种杂化材料具有优良的耐热性、耐溶剂性 ,高贮能模量 ,同时 ,该制备方法克服了稀土离子易缔合的缺点 ,获得了高稀土含量且均匀分布的三异丙氧基钕 /PMMA杂化材料     

Coupled atom transfer radical coupling and atom transfer radical polymerization approach for controlled grafting from poly(vinylidene fluoride) backbone

A new “grafting from” strategy for grafting of different monomers (methacrylates, acrylates, and acrylamide) on poly(vinylidene fluoride) (PVDF) backbone is designed using atom transfer radical coupling (ATRC) and atom transfer radical polymerization (ATRP). 4‐Hydroxy TEMPO moieties are anchored on PVDF backbone by ATRC followed by attachment of ATRP initiating sites chosen according to the reactivity of different monomers. High graft conversion is achieved and grafting of poly(methyl methacrylate) (PMMA) exhibits high degree of polymerization (DPn = 770) with a very low graft density (0.18 per hundred VDF units) which has been increased to 0.44 by regenerating the active catalyst with the addition of Cu(0). A significant impact on thermal and stress–strain property of graft copolymers on the graft density and graft length is noted. Higher tensile strain and toughness are observed for PVDF‐g‐PMMA produced from model initiator but graft copolymer from pure PVDF exhibits higher tensile strength and Young's modulus. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 995–1008     

The disorderly exfoliated LDHs/PMMA nanocomposites synthesized by in situ bulk polymerization: The effects of LDH-U on thermal and mechanical properties

The disorderly exfoliated layered double hydroxides/poly(methyl methacrylate) (LDHs/PMMA) nanocomposites were obtained in a two-stage process by the in situ bulk polymerization of methyl methacrylate (MMA) in the presence of 10-undecenoate intercalated LDH (LDH-U). The dispersed behavior of the LDH-U in the PMMA matrix was identified by using X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV/visible transmission spectroscopy. All these nanocomposites showed significantly enhancement of glass transition temperature (T_g) and the decomposition temperatures compared to pristine PMMA, as identified in differential scanning calorimetry (DSC) and thermogravimetric (TGA) analysis. The tensile modulus of these nanocomposites was also enhanced by incorporating the LDH-U into the PMMA matrix and increased as the amount of LDH-U increased. According to the analytical method of Ozawa-Flynn, the degradation activation energies of these nanocomposites are higher than that of pristine PMMA.     

非水凝胶原位聚合法制备含钐PMMA材料的研究

将无水三异丙氧基钐直接加入甲基丙烯酸甲酯（MMA）中会迅速形成凝胶,通过原位聚合可获得含钐的PMMA固体材料.研究表明,随钐含量的提高,含钐PMMA的结构逐渐由线型向交联网状体型转变,并使材料耐热性、耐溶剂性及贮能模量提高;ESEM表明,含钐PMMA呈交联网络蜂窝结构,未见聚集体,钐元素在体系中均匀分布;同时该材料呈现钐离子的特征荧光,在所测定的浓度范围内,荧光强度随钐含量增加而提高.     

Effect of Organic Nano Carboncapsule Incorporated Modified Clay on Fire‐Retardancy of PMMA Nanocomposites

Here we investigate a new type of highly flame retardant poly(methyl methacrylate) (PMMA) nanocomposite by bulk polymerization of methyl methacrylate (MMA) in the presence of organic nano carboncapsule (OCNC/NCNC)‐incorporated modified montmorillonites (CL120, CL42). The morphology of the modified clay was confirmed by X‐ray diffraction (XRD), and Fourier transform infrared (FT‐IR) spectroscopy was used to identify the functional groups in the clay. The nano morphological characterization of the clay in the PMMA matrix was confirmed by XRD and transmission electron microscopy (TEM). The thermal and mechanical properties of the PMMA nanocomposites were investigated by thermogravimetry and dynamic mechanical analysis, respectively. PMMA containing organo nano carboncapsule‐doped CL42 modified cocoamphodipropionate (K2) (P‐O‐CL42) could achieve very high thermal stability compared to pristine PMMA. The 5% thermal decomposition temperature (T _5d) increased by 63.2°C. Storage modulus of PMMA nanocomposites measured by DMA analysis. An enhancement of storage modulus and significant reduction in the peak heat release (PHR) rate were observed in the almost all PMMA nanocomposites as compared to pristine PMMA. Moreover, these results suggest that PMMA nanocomposites can have potential applications in the building industry and the medical field.     

Synthesis and characterization of polyaniline filled PU/PMMA interpenetrating polymer networks

A series of conducting interpenetrating polymer networks (IPNs), are prepared by sequential polymerization of castor oil based polyurethane (PU) with poly(methyl methacrylate) (PMMA) and polyaniline doped with camphor sulphonic acid (PAni)_CSA. The effect of different amount of PAni (varies from 2.5-12.5%) on the properties of PU/PMMA (50/50) IPNs such as electrical properties like conductivity, dielectric constant and dissipation factor; mechanical properties like tensile strength and percentage elongation at break have been reported. (PAni)_CSA filled IPNs shows improved tensile strength than the unfilled IPN system. The thermal stability and surface morphology of unfilled and (PAni)_CSA filled PU/PMMA (50/50) IPN sheets were investigated using a thermogravimetric analyzer (TGA) and a scanning electron microscope (SEM). TGA thermograms of (PAni)_CSA filled PU/PMMA (50/50) IPNs show a three-step thermal degradation process. SEM micrograms of filled PU/PMMA IPN system shows spherulitic structure at higher concentration of (PAni)_CSA.