球磨改性对(Ti Cr)_(0.497)V_(0.42)Fe_(0.083)/30%(w)(LaRMg)(NiCoAl)_(3.5)合金复合电极材料储氢和电化学性能的影响

以钒基合金(Ti Cr)0.497V0.42Fe0.083为基体,添加30%(w)稀土系A2B7型合金(LaRMg)(NiCoAl)3.5为电催化活性材料,采用机械球磨改性制备了储氢合金复合电极材料,研究其储氢特性和电化学性能.X射线衍射(XRD)、扫描电镜(SEM)和透射电子显微镜(TEM)分析结果表明,随球磨时间增加(t=0,0.5,1,3,5,10h),复合材料颗粒逐渐细化,A2B7型合金颗粒分散并包覆在钒基合金表面上;当球磨时间t≥5h时,复合材料形成明显的复合纳米晶组织并伴有部分非晶化倾向,同时钒基合金BCC相结构的晶胞参数a和晶胞体积V均明显减小.合金储氢特性及电化学性能分析测试结果表明,铸态纯钒基合金的吸氢量为3.11%(w),而球磨复合材料的储氢量随球磨时间增加呈减小的规律,其最大储氢量为2.47%(w);球磨改性后,复合材料电极的电催化性能得到明显改善,当球磨时间t≥3h时最大放电容量达到425.8mAh·g-1,经100次充放电循环后该电极的容量保持率(C100/Cmax)为97%,表现出良好的电极循环稳定性.     

混合稀土对A_2B_7型储氢合金结构和电化学性能的影响

采用感应熔炼方法制备了A2B7型La0.83-0.5x(Pr0.1Nd0.1Sm0.1Gd0.2)xMg0.17Ni3.1Co0.3Al0.1(x=0~1.66)储氢合金,并在He+Ar气氛和1 173 K下进行退火处理。通过X射线衍射(XRD)、扫描电子显微镜(SEM)和电化学方法,研究了混合稀土(Pr,Nd,Sm,Gd)替代La元素对合金物相结构和电化学性能的影响。合金相结构分析表明,混合稀土含量对合金组成和相结构有重要的影响,随混合稀土含量x的增加,合金中主相A2B7型(2H-Ce2Ni7型+3R-Gd2Co7型)相丰度逐渐增多,其中2H-Ce2Ni7型相丰度先增多后减少,3RGd2Co7型相丰度则逐渐增加,主相晶胞参数随x增加而减小。电化学结果表明,随混合稀土含量增加,放氢平台压逐渐升高,合金电极的最大放电容量和循环稳定性均呈先增大后减小的规律,其中x=0.4合金电极具有最高的电化学放电容量(389.8 mAh·g-1)和最佳的循环寿命(S100=91.30%);合金电极的高倍率放电性能(HRD)则随x的增加获得显著提高。适量的混合稀土替代量可显著改善合金电极的综合电化学性能。     

稀土氧化镱对La-Mg-Ni系A2B7型储氢合金电极性能的影响

研究了分别添加纳米和微米级稀土氧化物Yb2O3(%,质量分数)后对La-Mg-Ni系A2B7型储氢合金电极电化学性能的影响。研究结果表明,添加Yb2O3能有效抑制合金电极表面La(OH)3和Mg(OH)2析出,随Yb2O3含量增加,La-Mg-Ni系A2B7型储氢合金电极的循环稳定性提高,但电极放电容量有所降低,电极动力学反应极化增加;Yb2O3粉末颗粒尺寸和团聚状态对合金电极性能影响比较明显,添加纳米级/微米级Yb2O3后均降低了合金电极放电容量,其中微米级Yb2O3对合金电极循环稳定性的改善效果更为明显。合金电极的循环稳定性与其放电过程的截止电位(-0.8～-0.6 V,相对Hg/HgO电极)有关,随截止电位减小,合金腐蚀倾向增加,电极循环寿命变差;Yb2O3在截止电位区间发生的电化学氧化-还原反应与储氢合金电极循环稳定性关系密切。     

钆对La-Mg-Ni系A_2B_7型储氢合金微观结构和电化学性能的影响

用高频感应熔炼方法制备了稀土系A2B7型La0.83-xGdxMg0.17N i3.05Co0.3A l0.15(x=0~0.5)储氢合金,在Ar气氛中和1173 K下对铸态合金进行退火处理,通过X射线衍射(XRD)、电子探针显微分析方法(EPMA)和电化学测试等分析方法系统研究了稀土Gd部分替代La元素对合金微观组织和电化学性能的影响规律。研究结果表明,合金退火组织主要由Ce2N i7型、Gd2Co7型、Pr5Co19型、PuN i3型和CaCu5型相组成,稀土Gd元素能有效减少和抑制退火组织中CaCu5型相的形成,随Gd含量x增加,合金相组成中A2B7型(Ce2N i7和Gd2Co7型)相丰度呈先增加后减小的规律,当x=0.2时其相丰度最大(91.0%)。合金的PCT吸氢平台压随Gd含量的增加而升高,x=0.5时吸氢平台压力接近0.1 MPa,x=0.2时合金的吸氢量达到最大值1.34%。电化学测试分析表明,随Gd含量x的增加,合金电极最大放电容量和容量保持率均呈先增加后减小的规律,适量的Gd元素可明显改善合金的综合电化学性能。当x=0.2时,合金电极放电容量达到最大值392.9 mAh.g-1,经100...     

Ti0.10Zr0.15V0.35Cr0.10Ni0.30+5wt% LaNi5复合储氢合金的电化学性能与协同效应

为了改善钛钒基固溶体合金的电化学性能,利用两步电弧熔炼法制备复合储氢合金Ti0.10Zr0.15V0.35Cr0.10Ni0.30+5wt%LaNi5,X-射线衍射(XRD)和场发射扫描电镜-能谱(FESEM-EDS)显示:复合储氢合金的主相是体心立方结构的钒基固溶体相和六方结构的C14 Laves相,复合过程中生成了第二相。电化学测试结果表明:复合合金电极的P-C-T特征、活化性能、最大放电容量、循环稳定性、低温放电性能和动力学特性均较母体合金有显著改善。复合合金电极的活化周期数为5,最大放电容量为353.9 mAh.g-1,233 K时低温放电能力为50.26%。该复合合金电极的最大储氢容量、平台压、电荷转移电阻和交换电流密度均存在协同效应;在任意循环、在高/低温下以及在高倍率放电过程中,该复合合金电极的放电容量均存在协同效应。     

无镁超点阵结构A_2B_7型La_(1-x)Y_xNi_(3.25)Mn_(0.15)Al_(0.1)合金的储氢和电化学性能

采用真空电弧熔炼和热处理(950℃×10 h)方法制备了新型无镁超点阵结构A_2B_7型La_(1-x)Y_xNi_(3.25)Mn_(0.15)Al_(0.1)(x=0,0.25,0.50,0.67,0.75,0.85,1.00)退火合金,研究了A端稀土Y元素对退火合金微观组织结构、储氢行为及电化学性能的影响.结果表明,退火合金微观组织的主相均由Ce_2Ni_7型结构组成,随稀土Y含量x增大,Ce_2Ni_7型主相丰度呈先增加后减小的规律,同时Ce_2Ni_7型主相的晶胞体积V逐渐减小.气体储氢时,x=0~0.25合金无压力-组成-温度(PCT)曲线平台且易形成氢致非晶化;当x≥0.50时,合金能有效抑制储氢时的氢致非晶化倾向且具有明显的吸/放氢平台特征,吸氢平台压范围为0.026~0.097 MPa,最大储氢量为1.418%~1.48%(质量分数),储氢性能得到极大改善.电化学测试结果表明,x=0.50~0.85的合金具有较高的电化学放电容量(350.4~381 mA·h/g),经100次充放电循环后容量保持率S100=52%~85%,其中稀土Y含量x=0.67~0.75时的合金具有良好的储氢性能及较好的综合电化学性能.合金电极的高倍率放电性能HRD900=64.5%~85.7%,氢原子在合金体相中的扩散是电极反应动力学过程的控制步骤.     

稀土元素对R-Y-Ni系A2B7型无镁储氢合金微观结构和电化学性能的影响

采用真空电弧熔炼及退火处理制备R-Y-Ni系A_2B_7型R0.3Y0.7Ni3.25Mn0.15Al0.1(R=Y,La,Pr,Ce,Nd,Gd,Sm)储氢合金,系统研究稀土元素R对合金微观组织与结构、储氢和电化学性能的影响。XRD和SEM-EDS分析表明,合金退火组织由Ce2Ni7型主相、PuNi3型及少量Ca Cu5型相组成,Ce2Ni7型主相的晶格常数a、c及晶胞体积V均随稀土R原子半径的减小而依次降低。该合金均具有明显的吸放氢平台,常温下最大吸氢容量为1.17%~1.48%(w/w),吸氢平台压Peq为0.037~0.194 MPa。电化学分析表明,退火合金电极的电化学活化性能优良,R=La合金具有最高的放电容量(389.2 mAh·g-1)和较佳的容量保持率(充放电循环100次后的S100=85.7%),其中合金微观组织的不均匀性及稀土元素的电化学腐蚀是影响电极循环稳定性的主要原因。合金电极的高倍率放电性能(电流密度为900 m A·g-1)HRD900=71.05%~86.94%,其电极反应动力学控制步骤主要由氢原子在合金体相中的扩散速率所控制。     

镁含量对RE-Mg-Ni系A2B7型储氢合金结构与性能的影响

采用感应熔炼方法制备了La0.8-xGd0.2MgxNi3.1Co0.3Al0.1(x=0, 0.1, 0.15, 0.2, 0.25, 0.3, 0.4)储氢合金, 并在氩气气氛和1173 K下进行退火处理. 合金相结构分析结果表明, 镁含量(x)较低时合金以Ce2Ni7型为主相结构, A2B7型相丰度(Ce2Ni7+Gd2Co7)达到98.8%; 镁含量较高时合金相由A2B7型、 CaCu5型和PuNi3型物相构成, 随着镁含量的增加, PuNi3型和CaCu5型相组成逐渐增多, 其晶胞参数随Mg含量的增加而减小, 同时合金的吸氢平台也随之升高. 电化学测试结果表明, 随着合金中Mg含量增加, 合金电极的最大放电容量和循环稳定性均呈先增大后减小的规律, 其中x=0.15时合金电极具有最高的电化学放电容量(393 mA·h/g)和最佳的循环寿命(S100=92.82%). 合金电极的高倍率放电性能(HRD)随Mg含量的增加先减小再增大然后又减小, 适量的Mg元素改善了合金电极的动力学性能.     

La15Fe77B8型储氢合金的结构和电化学性能

研究了快淬和退火态La15Fe77B8型储氢合金的组织结构和电化学性能。应用中频感应熔炼-快淬方法制备了La15Fe77B8型储氢合金,其组成为La15Fe2Ni72Mn7B2Al2。结构分析表明:快淬La15Fe2Ni72Mn7B2Al2合金为多相结构,包括LaNi5相、La3Ni13B2相和(Fe,Ni)相,快淬合金经1223 K保温3 h,然后在873 K保温3 h退火处理后,LaNi5相增加,La3Ni13B2相几乎消失,(Fe,Ni)相增加且形态变大。电化学测试表明,退火合金的最大容量(307 mAh.g-1)略小于快淬合金(309 mAh.g-1),而循环稳定性有所改善。退火合金电极的倍率放电能力(HRD)低于快淬合金,原因在于交换电流密度(I0)及氢在合金中的扩散系数(D)降低。快淬和退火合金电极在低温233 K时均能放出55%的容量。     

La0.7-xNdxMg0.3Ni3.4Al0.1(x=0～0.4)储氢合金的相结构及电化学性能

采用真空烧结方式制备了AB3.5型La0.7-xNdxMg0.3Ni3.4Al0.1(x=0,0.1,0.2,0.3和0.4)储氢合金.XRD分析表明,所有合金均由LaNi5,La2Ni7和LaNi3三相组成.当Nd含量增加时,合金中的LaNi5和La2Ni7相含量有不同程度的增加,而LaNi3相相应减少.电化学性能测试表明,添加适量的Nd能改善合金电极的循环稳定性,其中La0.6Nd0.1Mg0.3Ni3.4Al0.1合金具有相对较好的综合性能,其最大放电容量达到322.4 mAh·g-1,循环50周的容量保持率(S50)达到89.98%.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.