Synthesis of efficient TiO2-based photocatalysts by phosphate surface modification and the activity-enhanced mechanisms

A simple strategy to greatly increase the thermal stability of nanocrystalline anatase has been put forward to fabricate efficient TiO₂-based photocatalysts under ultraviolet irradiation, via the surface modification with phosphate anions. The results show that the increased anatase thermal stability is attributed to the roles of the phosphate modification effectively inhibiting the contacts among anatase nanocrystals. Compared to un-modified TiO₂, the modified TiO₂ calcined at high temperature (over 700 °C) exhibits much high photocatalytic activity for degrading Rhodamine B (or phenol) solution, even superior to the commercial P25 TiO₂. The activity enhancement is mainly attributed to the increased separation rate of photogenerated charge carriers on the basis of the measurements of steady state- and transient state-surface photovoltage spectroscopy. This work would provide a practical route to reasonably design and synthesize high-performance TiO₂-based nanostructured photocatalysts with high anatase thermal stability.     

Photoelectrocatalytic degradation of organic contaminants at Bi2O3/TiO2 nanotube array electrode

In the current work, TiO₂ nanotube array was prepared via electrochemical anode method. Then the Bi₂O₃ nanoparticles were deposited onto the TiO₂ nanotube array via dip-coating method from an amorphous complex precursor. The crystal structures were characterized via X-ray diffraction analysis. Their surface textures were observed via electron-scanning microscope. The prepared composite array electrode exhibited high photoelectrocatalytic activities towards degrading organic contaminants under visible light irradiation. High photoelectrocatalytic activities were also exhibited under UV light irradiation. The catalytic mechanism was discussed based on the analysis of electrochemical and degradation kinetics results. It is suggested a P (Bi₂O₃)-N (TiO₂) junction was formed to increase the catalytic activates. The stability of the electrode materials was confirmed finally.     

亚纳米厚的氧化铝包裹层可以显著提高负载型金纳米颗粒催化剂的热稳定性

负载型金纳米颗粒催化剂在许多催化反应中展现出非常好的催化活性,但是金纳米颗粒在高温等反应条件下容易烧结团聚,极大地限制了金催化剂的应用。利用原子层沉积技术在Au/TiO₂催化剂表面分别精确沉积了一层超薄的二氧化钛和氧化铝包裹层,并对比研究了包裹层对金纳米颗粒的热稳定性影响。原位红外漫反射CO吸附和x-射线光电子能谱数据证实了氧化物包裹层的存在。发现亚纳米厚的氧化铝包裹层能够在600 C完全避免金纳米颗粒的团聚;相反,二氧化钛包裹层对金纳米颗粒稳定性的提高没有明显效果。通过CO氧化探针反应的活性测试,发现随着煅烧温度的升高氧化铝包裹的Au/TiO₂ 催化剂的活性逐渐提高,表明高温处理可以促进被包裹金原子的暴露并表现出催化活性。提供了提高金纳米颗粒稳定性的有效方法,为拓展金催化剂在条件苛刻的反应中的应用奠定了技术基础.     

Mn,N共掺杂对锐钛矿相TiO2微观结构和性能的影响

采用第一性原理平面波超软赝势方法,系统研究了Mn,N共掺杂对锐钛矿相TiO₂的晶体结构、缺陷形成能、电子结构、光学性质以及氧化还原能力的影响.研究表明:Mn,N共掺杂锐钛矿相TiO₂后,TiO₂晶格发生了畸变,导致晶体八面体偶极矩增加,有利于光生电子-空穴对的有效分离;在TiO₂带隙中出现了杂质能级,使锐钛矿相TiO₂的光学吸收带边红移,可见光区的吸收系数明显增大,有利于光催化效率的提高;在不考虑 关键词： 2')" href="#">锐钛矿相TiO₂ 第一性原理 Mn和N共掺杂 光催化性能     

Preparation of photocatalytic Fe2O3-TiO2 coatings in one step by metal organic chemical vapor deposition

There are two major difficulties in the TiO₂ liquid-solid photocatalytic system: effective immobilization of the TiO₂ particles; and improving the catalytic activity under visible light. To simultaneously solve these two problems, Fe₂O₃-TiO₂ coatings supported on activated carbon fiber (ACF), have been prepared in one step by a convenient and efficient method—metal organic chemical vapor deposition (MOCVD). XRD results revealed that Fe₂O₃-TiO₂ coatings mainly composed of anatase TiO₂, α-Fe₂O₃ phases and little Fe₂Ti₃O₉. The pore structure of ACF was preserved well after loading with Fe₂O₃-TiO₂ coatings. UV-vis diffuse reflectance spectra showed a slight shift to longer wavelengths and an enhancement of the absorption in the visible region for Fe₂O₃-TiO₂ coatings, compared to the pure TiO₂ sample. A moderate Fe₂O₃-TiO₂ loading (13.7 wt%) was beneficial to mineralizing wastewater because the intermediates could be adsorbed onto the surface of photocatalyst following decomposition. The stable performance revealed that the Fe₂O₃-TiO₂ coatings were strongly adhered to the ACF surface, and the as prepared catalysts could be reused showing potential application for wastewater treatment.     

三元异质结构Ag-Bi2MoO6/BiPO4光催化剂高效降解苯酚红

多组分复合体系有利于电荷的有效分离,减少电子空穴对的复合几率。通过低温液相法首次合成Ag-Bi₂MoO₆/BiPO₄三元异质结构光催化剂。利用XRD、SEM、EDX及XPS等技术对样品进行了表征。结果表明,Ag纳米粒子光照积累在Bi₂MoO₆/BiPO₄的表面,通过表面等离子共振增加对可见光的吸收,同时作为电子受体促进了光生电子的转移。Ag、BiPO₄和Bi₂MoO₆形成三元异质结构有效地抑制了光生电子空穴对的复合。Ag-Bi₂MoO₆/BiPO₄表现出优异的光催化性能,其光催化活性较BiPO₄、Bi₂MoO₆和Bi₂MoO₆/BiPO₄样品有较大提高。并且对Ag-Bi₂MoO₆/BiPO₄三元异质结构的光催化机制进行了讨论。光催化过程中反应活性物种捕获实验结果表明h⁺和O₂^·-是主要的活性基团.     

Bi2MoO6纳米片/TiO2纳米棒阵列复合材料的制备及其可见光响应光电催化性能研究

Novel Bi₂MoO₆/TiO₂ heterojunction was fabricated by growing Bi₂MoO₆ nanosheets arrays on the vertically aligned TiO₂ nanorods arrays via a two-step solvothermal method. The obtained Bi₂MoO₆/TiO₂ hierarchical heterojunction showed excellent visible light photoelectrochemical performance. Compared with the pure TiO₂ and Bi₂MoO₆, the photocurrent density of the heterojunction was increased 57 and 29 times, respectively. Furthermore, the hydrogen generation rate of the Bi₂MoO₆/TiO₂ for photoelectrocatalytic water-splitting was about 6 times higher than that of the pure Bi₂MoO₆. The improved performance can be attributed to the synergistic effects of enhanced absorption of visible light, increase of migration rate and separation efficiency of photo-induced carriers.     

Electronic and optical properties of pure and Mo doped anatase TiO2 using GGA and GGA+U calculations

Comparative GGA and GGA+U calculations for pure and Mo doped anatase TiO₂ are performed based on first principle theory, whose results show that GGA+U calculation provide more reliable results as compared to the experimental findings. The direct band gap nature of the anatase TiO₂ is confirmed, both by using GGA and GGA+U calculations. Mo doping in anatase TiO₂ narrows the band gap of TiO₂ by introducing Mo 4d states below the conduction band minimum. Significant reduction of the band gap of anatase TiO₂ is found with increasing Mo doping concentration due to the introduction of widely distributed Mo 4d states below the conduction band minimum. The increase in the width of the conduction band with increasing doping concentration shows enhancement in the conductivity which may be helpful in increasing electron–hole pairs separation and consequently decreases the carrier recombination. The Mo doped anatase TiO₂ exhibits the n-type characteristic due to the shifting of Fermi level from the top of the valence band to the bottom of the conduction band. Furthermore, a shift in the absorption edge towards visible light region is apparent from the absorption spectrum which will enhance its photocatalytic activity. All the doped models have depicted visible light absorption and the absorption peaks shift towards higher energies in the visible region with increasing doping concentration. Our results describe the way to tailor the band gap of anatase TiO₂ by changing Mo doping concentration. The Mo doped anatase TiO₂ will be a very useful photocatalyst with enhanced visible light photocatalytic activity.     

Response improvement for In2O3-TiO2 thick film gas sensors

In₂O₃ is introduced into TiO₂ by sol-gel method to improve the response/recovery rate and expand the operating temperature, when the In₂O₃-TiO₂ mixed system is exposed to H₂/O₂. The sensor is fabricated by thick film technology. Influence of In₂O₃ on the film phase composition, microstructure and sensing characteristics is discussed. Dynamic response properties show that the operating temperature of the mixed system is at 500-800 °C, which is about 600-800 °C for pure TiO₂. Response time of the sensor is about 200-260 ms (millisecond) while recovery time is in a narrow range of 60-280 ms at 600-800 °C. The promoting mechanism is suggested to arise from the introduction of In₂O₃ and grain size effect of the sensing film. Then In₂O₃-TiO₂ thick films are surface-modified by Pt using chloroplatinic acid. The promoting effect of Pt dispersed on the mixed system is also investigated.     

Synthesis and characterization of TiO2/Fe2O3 core-shell nanocomposition film and their photoelectrochemical property

TiO₂/Fe₂O₃ core-shell nanocomposition film has been fabricated via two-step method. TiO₂ nanorod arrays are synthesized by a facile hydrothermal method, and followed by Fe₂O₃ nanoparticles deposited on TiO₂ nanorod arrays through an ordinary chemical bath deposition. The phase structures, morphologies, particle size, chemical compositions of the composites have been characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and ultraviolet-visible (UV-vis) spectrophotometer. The results confirm that Fe₂O₃ nanoparticles of mean size ca. 10 nm coated on the surface of TiO2 NRs. After depositing Fe₂O₃, UV-vis absorption property is induces the shift to the visible-light range, the annealing temperature of 600 °C is the best condition for UV-vis absorption property of TiO₂/Fe₂O₃ nanocomposite film, and increasing Fe content, optical activity are enhanced one by one. The photoelectrochemical (PEC) performances of the as-prepared composite nanorods are determined by measuring the photo-generated currents under illumination of UV-vis light. The TiO₂ NRs modified by Fe₂O₃ show the photocurrent value of 1.36 mA/cm² at 0 V vs Ag/AgCl, which is higher than those of unmodified TiO₂ NRs.     

N,Co共掺杂锐钛矿相YiO2光催化剂的第一性原理研究

采用第一性原理平面波超软赝势方法研究了N,Co共掺杂锐钛矿相TiO2的微观结构和光学性质.结果表明:N,Co共掺杂后TiO2晶格中产生的偶极矩使光生电子-空穴对更有效地分离;在TiO2导带和价带之间形成了新的杂质能级,一方面使吸收带边红移到可见光区,光吸收性能明显增强,另一方面有利于光生电子-空穴对的分离,提高TiO2的光量子效率;与纯TiO2相比,N,Co共掺杂锐钛矿相TiO2带边的氧化还原势只有微小的变化,共掺杂后TiO2的强氧化还原能力得以保持.     

Cocktail effect of Fe2O3 and TiO2 semiconductors for a high performance dye-sensitized solar cell

The bi-semiconductors of TiO₂ and Fe₂O₃ were used as a photoelectrode material in a high performance dye-sensitized solar cell due to cocktail effects from the two conduction bands. The size of the semiconductors was reduced by using a paint shaker to enlarge the contact area of the semiconductor with the dye or electrolyte. The fill factor and the efficiency of the prepared dye-sensitized solar cell were improved by over 16% and 300%, respectively; these parameters were measured from a current-voltage curve that was based on the effects of the Fe₂O₃ co-semiconductor and the size reduction. A mechanism is suggested wherein the conduction band of Fe₂O₃ works to prohibit the trapping effects of electrons in the conduction band of TiO₂. This result is attributed to the prevention of electron recombination between electrons in the TiO₂ conduction band with dye or electrolytes. The mechanism is suggested based on impedance results, which indicate improved electron transport at the interface of the TiO₂/dye/electrolyte.     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

Preparation and characterization of visible light responsive Fe2O3-TiO2 composites

In this study we present the effects of iron oxide (Fe₂O₃) on titanium dioxide (TiO₂) in synthesising visible-light reactive photocatalysts. A Fe₂O₃-TiO₂ composite photocatalyst was synthesized from Fe₂(SO₄)₃ and Ti(SO₄)₂ by a ethanol-assisted hydrothermal method. The preparation conditions were optimized through the investigation of the effects of hydrothermal temperature and time as well as molar ratio of Ti to Fe on the photocatalytic activity. The visual, physical and chemical properties of the Fe₂O₃-TiO₂ composites were investigated. The results showed that α-Fe₂O₃ and anatase TiO₂ were present in the composites. The Fe₂O₃-TiO₂ synthesized under optimum condition consisted of mesoporous structure with an average pore size of 4 nm and a surface area of 43 m²/g. Under visible and solar light irradiation, the photocatalytic activity of optimized sample was significantly higher than that of pure TiO₂. This sample led to a photodegradation efficiency of 90% and 40% of auramine under visible light and solar light, respectively.     

光沉积Ru和RuO2的锐钛矿TiO2纳米片的光解水产氧

采用水热法以HF作为结构调控剂合成了主要暴露（001）面的锐钛矿TiO₂纳米片,通过光沉积方法分别合成了负载Ru和RuO₂物种的光催化剂。利用X射线衍射、透射电镜和氢气程序升温还原等分析表征了催化剂的结构性质。通过光解水产氧反应来研究催化剂的催化性能,详细考察了Ru含量、负载方式以及氧化和还原处理等因素的影响,光解水产氧速率的差异证明了Ru物种在不同晶面的电荷-空穴分离效应。与负载单一助催化剂的Ru/TiO₂和RuO₂/TiO₂样品相比,活性最优的0.5%Ru-1.0%RuO₂/TiO₂样品由于负载了双助催化剂,其催化活性得到更大的提高,证实了在锐钛矿TiO₂上的晶面电荷-空穴分离效应.     

锐钛矿相和金红石相TiO2:Nb的光电性能研究

采用基于密度泛函理论的第一性原理计算了锐钛矿相和金红石相TiO₂:Nb的晶体结构、电子结构和光学性质. 结果表明, 在相等的摩尔掺杂浓度下(6.25%), 锐钛矿相TiO₂:Nb的导带底电子有效质量小于金红石相TiO₂:Nb, 且前者室温载流子浓度是后者的两倍左右, 即具有更大的施主杂质电离率, 从而解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb具有更优异电学性能的实验现象. 光学计算也表明锐钛矿相在可见光区有更大的透过率, 从而在理论上解释了锐钛矿相TiO₂:Nb比金红石相TiO₂:Nb更适于做透明导电材料的原因. 计算结果与实验数据能较好符合. 关键词： 2:Nb')" href="#">TiO₂:Nb 第一性原理 电子结构 光学性能     

大规模合成具有氧空位的多孔Bi2O3用于有效降解亚甲基蓝

光催化降解有机污染物由于其具有低能耗和绿色环保的特点，已经成为研究的热点. 氧化铋纳米晶体的带隙在2.0∽2.8 eV之间，利用它催化可见光降解有机污染物具有较高的活性，从而引起了越来越多的关注. 尽管近年来已经开发了几种制备Bi₂O₃基半导体材料的方法，但是仍然难以用简单的方法大规模地制备高活性的Bi₂O₃催化剂. 因此，开发简单可行的大规模制备Bi₂O₃纳米晶体的方法对于工业废水处理的潜在应用具有重要意义. 本文通过蚀刻商用BiSn粉末，然后进行热处理，成功地大规模制备了多孔Bi₂O₃. 获得的多孔Bi₂O₃在亚甲基蓝(MB)的光催化降解中表现出优异的活性和稳定性. 对该机理的进一步研究表明，多孔Bi₂O₃合适的能带结构允许生成活性氧物种，例如O₂^-·和·OH，可有效降解MB.     

Fabrication, characterization and photoelectrochemical properties of Fe2O3 modified TiO2 nanotube arrays

TiO₂ nanotube (NT) arrays modified by Fe₂O₃ with high sensibility in the visible spectrum were first prepared by annealing anodic titania NTs pre-loaded with Fe(OH)₃ which was uniformly clung to the titania NTs using sequential chemical bath deposition (S-CBD). The photoelectrochemical performances of the as-prepared composite nanotubes were determined by measuring the photo-generated currents and voltages under illumination of UV-vis light. The titania NTs modified by Fe₂O₃ showed higher photopotential and photocurrent values than those of unmodified titania NTs. The enhanced photoelectrochemical behaviors can be attributed to the modified Fe₂O₃ which increases the probability of charge-carrier separation and extends the range of the TiO₂ photoresponse from ultraviolet (UV) to visible region due to the low band gap of 2.2 eV of Fe₂O₃.     

Deposition and characterization of binary Al2O3/SiO2 coating layers on the surfaces of rutile TiO2 and the pigmentary properties

Binary Al₂O₃/SiO₂-coated rutile TiO₂ composites were prepared by a liquid-phase deposition method starting from Na₂SiO₃·9H₂O and NaAlO₂. The chemical structure and morphology of binary Al₂O₃/SiO₂ coating layers were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, TG-DSC, Zeta potential, powder X-ray diffraction, and transmission electron microscopy techniques. Binary Al₂O₃/SiO₂ coating layers both in amorphous phase were formed at TiO₂ surfaces. The silica coating layers were anchored at TiO₂ surfaces via Si-O-Ti bonds and the alumina coating layers were probably anchored at the SiO₂-coated TiO₂ surfaces via Al-O-Si bonds. The formation of continuous and dense binary Al₂O₃/SiO₂ coating layers depended on the pH value of reaction solution and the alumina loading. The binary Al₂O₃/SiO₂-coated TiO₂ composites had a high dispersibility in water. The whiteness and brightness of the binary Al₂O₃/SiO₂-coated TiO₂ composites were higher than those of the naked rutile TiO₂ and the SiO₂-coated TiO₂ samples. The relative light scattering index was found to depend on the composition of coating layers.     

Investigation into the effects of deposition parameters on TiO2 photocatalyst thin films by rf magnetron sputtering

Titanium dioxide (TiO₂) photocatalyst thin films were deposited on non-alkali glass substrates by radio frequency (rf) magnetron sputtering. The Taguchi method with orthogonal array, signal-to-noise ratio and analysis of variance were employed to study the performance characteristics. The experimental studies were conducted under different rf powers, sputtering pressures, O₂/(Ar+O₂) flow-rate ratios, and substrate temperatures. The deposited TiO₂ films were of the anatase phase with a (101) preferred orientation. We performed both photoinduced decomposition of methylene blue (MB) and photoinduced hydrophilicity under UV light illumination. With the optimized TiO₂ photocatalyst thin film deposition conditions, the water contact angle after 9 min UV illumination was approximately 5, the absorbance of MB was reduced to 0.2 for 240 min UV irradiation, and the deposition rate was 34.18 Å/min.