S掺杂对锐钛矿相TiO2电子结构与光催化性能的影响

采用基于第一性原理的平面波超软赝势方法研究了掺杂不同价态S的锐钛矿相TiO₂的晶体结构、杂质形成能、电子结构及光学性质.计算结果表明硫在掺杂体系中的存在形态与实验中的制备条件有关;掺杂后晶格发生畸变、原子间的键长及原子的电荷量也发生了变化,导致晶体中的八面体偶极矩增大; S 3p态与O 2p态、Ti 3d态杂化而使导带位置下移、价带位置上移及价带宽化,从而导致TiO₂的禁带宽度变窄、光吸收曲线红移到可见光区.这些结果很好地解释了S掺杂锐钛矿相TiO₂在可见光下具有优良的光催化性能的内在原因.根据计算结果分析比较了硫以不同离子价态掺杂对锐钛矿相TiO₂电子结构和光催化性能影响的差别. 关键词： 2')" href="#">锐钛矿相TiO₂ S掺杂 第一性原理 光催化性能     

Effects of native defects on the electronic structure and photocatalytic activity in anatase TiO2 by first principles calculations

The crystal structure, electronic structure, optical properties and photocatalytic activity of the native defects in anatase TiO₂ were investigated based on the density-functional theory (DFT). The results show that oxygen vacancies (V_O) have the lowest formation energy, and thus are easiest to form in the bulk structure. The conduction and valence band moves to the high or low energy region, and the energy gap becomes narrower for the native point defect models. In particular, oxygen interstitials (O_i) have a direct band gap, and new gap states appear in the band gap, which can be responsible for the high photocatalytic efficiency in anatase TiO₂. The phenomenon of “impurity compensation” takes place for the oxygen and titanium interstitials. Ti vacancy (V_Ti) can promote the utilization of solar light by analyzing the absorption spectra. All the calculated results show that O_i and V_Ti are beneficial in improving the photocatalytic activity of TiO₂ in the UV–visible light range.     

Concentration-dependent electronic structure and optical absorption properties of B-doped anatase TiO2

The concentration-dependent electronic structures and optical properties of B-doped anatase TiO₂ have been calculated using the density functional theory. The calculated results indicate that the electronic structures of B-doped TiO₂ have changed compared with those of pure TiO₂, which is mainly due to the new midgap states induced by B doping. As to the optical properties, we calculate the imaginary part of dielectric function ε₂(ω) and optical absorption spectra of pure and B-doped TiO₂. Two transitions E₁ and E₂ emerged after B doping. The intensity of absorption is enhanced by B doping both in the UV and visible regions. According to the results of imaginary part of dielectric function ε₂(ω) and DOS, it can be concluded that the two optical transitions correspond to the transitions from the O 2p states in the top of valence band to the midgap states and from the midgap states to the Ti 3d states in the bottom of conduction band, respectively. These results have important implications for the further development of photocatalytic materials.     

First-principles study on anatase TiO2 codoped with nitrogen and praseodymium

The crystal structures, electronic structures and optical properties of nitrogen or/and praseodymium doped anatase TiO₂ were calculated by first principles with the plane-wave ultrasoft pseudopotential method based on density functional theory. Highly efficient visible-light-induced nitrogen or/and praseodymium doped anatase TiO₂ nanocrystal photocatalyst were synthesized by a microwave chemical method. The calculated results show that the photocatalytic activity of TiO₂ can be enhanced by N doping or Pr doping, and can be further enhanced by N+Pr codoping. The band gap change of the codoping TiO₂ is more obvious than that of the single ion doping, which results in the red shift of the optical absorption edges. The results are of great significance for the understanding and further development of visible-light response high activity modified TiO₂ photocatalyst. The photocatalytic activity of the samples for methyl blue degradation was investigated under the irradiation of fluorescent light. The experimental results show that the codoping TiO₂ photocatalytic activity is obviously higher than that of the single ion doping. The experimental results accord with the calculated results.     

Mn,N共掺杂对锐钛矿相TiO2微观结构和性能的影响

采用第一性原理平面波超软赝势方法,系统研究了Mn,N共掺杂对锐钛矿相TiO₂的晶体结构、缺陷形成能、电子结构、光学性质以及氧化还原能力的影响.研究表明:Mn,N共掺杂锐钛矿相TiO₂后,TiO₂晶格发生了畸变,导致晶体八面体偶极矩增加,有利于光生电子-空穴对的有效分离;在TiO₂带隙中出现了杂质能级,使锐钛矿相TiO₂的光学吸收带边红移,可见光区的吸收系数明显增大,有利于光催化效率的提高;在不考虑 关键词： 2')" href="#">锐钛矿相TiO₂ 第一性原理 Mn和N共掺杂 光催化性能     

First-principles study of electronic structures and optical properties of Cu, Ag, and Au-doped anatase TiO2

We perform first-principles calculations to investigate the band structure, density of states, optical absorption, and the imaginary part of dielectric function of Cu, Ag, and Au-doped anatase TiO₂ in 72 atoms systems. The electronic structure results show that the Cu incorporation can lead to the enhancement of d states near the uppermost of valence band, while the Ag and Au doping cause some new electronic states in band gap of TiO₂. Meanwhile, it is found that the visible optical absorptions of Cu, Ag, and Au-doped TiO₂, are observed by analyzing the results of optical properties, which locate in the region of 400-1000 nm. The absorption band edges of Cu, Ag, and Au-doped TiO₂ shift to the long wavelength region compared with the pure TiO₂. Furthermore, according to the calculated results, we propose the optical transition mechanisms of Cu, Ag, and Au-doped TiO₂. Our results show that the visible light response of TiO₂ can be modulated by substitutional doping of Cu, Ag, and Au.     

IR and XPS investigation of visible-light photocatalysis—Nitrogen-carbon-doped TiO2 film

To use solar irradiation or interior lighting efficiently, we sought a photocatalyst with high reactivity under visible light. Nitrogen and carbon doping TiO_2−x−yN_xC_y films were obtained by heating the TiO₂ gel in an ionized N₂ gas and then were calcined at 500 °C. The TiO_2−x−yN_xC_y films have revealed an improvement over the TiO₂ films under visible light (wavelength, 500 nm) in optical absorption and photocatalytic activity such as photodegradation of methyl orange. X-ray photoemission spectroscopy, infrared spectrum and UV-visible (UV-vis) spectroscopy were used to find the difference of two kinds of films. Nitrogen and carbon doped into substitutional sites of TiO₂ has been proven to be indispensable for band-gap narrowing and photocatalytic activity.     

Nd高掺杂锐钛矿相TiO2电子结构和吸收光谱的第一原理研究

基于密度泛函理论平面波超软赝势方法, 采用第一原理研究未掺杂和不同浓度Nd高掺杂锐钛矿相TiO₂的电子结构和吸收光谱. 计算结果表明, 在本文限定的Nd高掺杂浓度范围内, Nd高掺杂浓度越小, 锐钛矿相TiO₂的禁带宽度越窄, 吸收光谱发生红移越显著. 计算结果与实验结果变化趋势相一致.     

N,Co共掺杂锐钛矿相YiO2光催化剂的第一性原理研究

采用第一性原理平面波超软赝势方法研究了N,Co共掺杂锐钛矿相TiO2的微观结构和光学性质.结果表明:N,Co共掺杂后TiO2晶格中产生的偶极矩使光生电子-空穴对更有效地分离;在TiO2导带和价带之间形成了新的杂质能级,一方面使吸收带边红移到可见光区,光吸收性能明显增强,另一方面有利于光生电子-空穴对的分离,提高TiO2的光量子效率;与纯TiO2相比,N,Co共掺杂锐钛矿相TiO2带边的氧化还原势只有微小的变化,共掺杂后TiO2的强氧化还原能力得以保持.     

Formation of impurity bands in iodine cation substitutionally doped TiO2 and its effects on photoresponse and photogenerated carriers

First-principles calculations based on the plane-wave pseudopotential (PWP) method were performed to investigate the electronic structure of iodine cation substitutionally doped anatase TiO₂ (referred to as I_sTiO₂). A 2×2×1 anatase supercell, in which one Ti atom was substituted by one iodine atom, was constructed for calculations. The calculated results reveal that iodine dopant contributes part of its 5s states to form one isolated impurity band in band gap and part of its 5p states to form some impurity bands at the bottom of conductive bands. The visible light response of I_sTiO₂ should be the consequence of the excitation between the two types of impurity bands (2.77 eV, about 450 nm). According to the distribution of impurity states, iodine dopant is considered to serve as a recombination center or an efficient trap for photogenerated carriers. This deduction was partly approved by water photosplitting under visible light irradiation.     

Doping mode, band structure and photocatalytic mechanism of B-N-codoped TiO2

The photocatalyst B and N codoped TiO₂ (B-N-TiO₂) was prepared via the sol-gel method by using boric acid and ammonia as B and N precursors. The doping mode, band structure and photocatalytic mechanism of B-N-TiO₂ were investigated well and elucidated in detail. B-N-TiO₂ showed the narrowed band gap and thus extended the optical absorption due to interstitial N and [NOB] species in the TiO₂ crystal lattice. The coexistence of interstitial N and [NOB] species in the TiO₂ crystal lattice and surface NO_x species allowed the more efficient utilization of visible light. Simultaneously, interstitial [NOB] and N species and surface B₂O₃ and NO_x species facilitated the separation of photo generated electrons and holes and suppress their recombination effectively. Hence, B-N-TiO₂ showed a higher photocatalytic activity than pure TiO₂, N-doped TiO₂ (N-TiO₂) and B-doped TiO₂ (B-TiO₂) under both UV and visible light irradiation.     

P掺杂锐钛矿相TiO2的第一性原理计算

利用基于密度泛函理论的第一性原理对不同P掺杂形式(P替位Ti, P替位O, 间隙P)的锐钛矿相TiO₂的晶格常数、电荷布居、能带结构、分态密度和吸收光谱进行了计算. 结果表明, P替位Ti时, TiO₂体积减小, P替位O和间隙P的存在使TiO₂的体积膨胀; 替位Ti的P和间隙P均有不同程度的氧化, 而替位O的P带有负电荷. 三种P掺杂形式均导致锐钛矿相TiO₂禁带宽度的增大, 并在TiO₂禁带之内引入了掺杂局域能级. P掺杂导致TiO₂禁带宽度增大的程度依次为: 间隙P>P替位Ti>P替位O. 吸收光谱的计算结果表明, P替位Ti并不能增强TiO₂的可见光吸收能力, 但间隙P的存在大幅提高了TiO₂的可见光光吸收能力, 间隙P有可能是造成实验上P掺杂增强锐钛矿相TiO₂光催化活性的重要原因. 关键词： P掺杂 2')" href="#">锐钛矿相TiO₂ 第一性原理     

Sm-N共掺杂对锐钛矿相TiO2的电子结构和吸收光谱影响的第一性原理研究

采用基于密度泛函理论框架下的第一性原理平面波超软赝势方法, 建立了N, Sm分别单掺杂以及Sm-N共掺杂的锐钛矿TiO₂超胞模型, 对其态密度、能带结构和吸收光谱进行了计算. 结果表明: N单掺杂的锐钛矿TiO₂的红移效果最强, 但Sm-N共掺杂锐钛矿TiO₂的载流子寿命更长, 且共掺杂形成的体系更加稳定.     

(Mo + N) codoped TiO2 for enhanced visible-light photoactivity

A series of Ti_1−xMo_xO_2−yN_y samples were prepared by using sol-gel method and characterized by X-ray diffraction, transmission electron microscopy and UV-vis absorption spectroscopy. All Ti_1−xMo_xO_2−yN_y samples are anatase phase. It is found that Mo, N mono-doping can increase visible light absorption, while (Mo + N) co-doping can greatly enhance absorption in whole visible region. Results of our first-principles band structure calculations reveal that (Mo + N)-doping, especially passivated co-doping can increase the up-limit of dopant concentration and create more impurity bands in the band gap of TiO₂, which leads to a greatly increase of its visible-light absorption without a decrease of its redox potential. It reveals that (Mo + N) co-doped TiO₂ is promising for a photocatalyst with high photocalystic activity under visible light.     

Properties of carbon and iron modified TiO2 photocatalyst synthesized at low temperature and photodegradation of acid orange 7 under visible light

The nanoparticles of TiO₂ modified with carbon and iron were synthesized by sol-gel followed solvothermal method at low temperature. Its chemical composition and optical absorption were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), photoluminescence emission spectroscopy (PL), UV-vis absorption spectroscopy, and electron paramagnetic resonance (EPR). It was found that carbon and iron modification causes the absorption edge of TiO₂ to shift the visible light region. Fe(III) cation could be doped into the matrix of TiO₂, by which could hinder the recombination rate of excited electrons/holes. Superior photocatalytic activity of TiO₂ modified with carbon and iron was observed for the decomposition of acid orange 7 (AO7) under visible light irradiation. The synergistic effects of carbon and iron in modified TiO₂ nanoparticles were responsible for improving visible light photocatalytic activity.     

3d过渡金属掺杂锐钛矿相TiO2的第一性原理研究

采用基于密度泛函理论的平面波超软赝势方法研究了纯锐钛矿相TiO₂及掺杂3d过渡金属TiO₂的几何、电子结构及光学性质. 计算结果表明掺杂能级的形成主要是掺杂过渡金属3d轨道的贡献，掺杂能级在禁带中的位置是决定TiO₂吸收带边能否出现红移的重要因素. Cr，Mn，Fe，Ni，Co，Cu掺杂使TiO₂的吸收带边产生红移，并在可见光区有一定的吸收系数； Sc，Zn掺杂使TiO₂的吸收带边产生蓝移，但在可见光区有较大的吸收系数；掺V不但使TiO₂的吸收带边产生红移，增强了在紫外光区的光吸收，而且在可见光区有非常大的吸收系数.     

First-principle calculations on optical properties of C-N-doped and C-N-codoped anatase TiO2

The electronic structures, dipole moment and optical properties of C-N-doped and C-N-codoped anatase titanium dioxide (TiO₂) are studied using the plane-wave ultrasoft pseudopotential method of density functional theory (DFT). The results revealed that the absorption coefficients of pure TiO₂ and N-doped TiO₂ are consistent with experimental values in the visible-light region. The bands originating from C/N-2p states lie in the band gap of doped TiO₂. A visible-light absorption edge red-shift can be observed. The atomic charges have changed, resulting in devation of the center of gravity of the negative electric charge from the positive electric charge in the super-cell, and their dipole moment would not be zero. The dipole moment has large influence on the optical responses in the visible region of TiO₂. Because of the small distance (0.531 nm) between C and N atoms, the covalent bond component was easily enhanced between C atom and adjacent O atom, the covalent bonds making it more difficult for the carrier transfer. Moreover, its optical absorption coefficient is going to reduce in the visible-light region. Under the condition of the larger distance (0.691 nm) between C and N atoms, their interaction can be reduced, which is beneficial to electrons transition; as a result, a significant improvement of the photocatalytic activity of TiO₂ has been found under the visible-light irradiation.     

Preparation and visible light photocatalytic activity of mesoporous N, S-codoped TiO2(B) nanobelts

The mesoporous N, S-codoped TiO₂(B) nanobelts are synthesized via hydrothermal synthesis and post-treatment, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements (BET), X-ray photoelectron spectra (XPS), and UV-vis diffuse reflectance spectra (DRS). The results show that the prepared samples are mesoporous structured and exhibit stronger absorption in the visible light region with red shift in the absorption edge. The photocatalytic activity of N, S-codoped mesoporous TiO₂(B) nanobelts is evaluated by the photocatalytic photodegradation of potassium ethyl xanthate (KEX) under visible light irradiation. It is found that the photocatalytic activity of the prepared samples increases with increasing the molar ratio of thiourea to Ti (R). At R = 3, the photocatalytic activity of the N, S-codoped TiO₂(B) sample TBLTS-3 reaches a maximum value. With further increasing R, the photocatalytic activity of the sample decreases. The high photocatalytic activity of N, S-codoped TiO₂(B) nanobelts can be attributed to the balance between strong absorption in visible light region and low recombination rate of electron/hole pairs.     

Synthesis and characterization of the Pd/InVO4-TiO2 co-doped thin films with visible light photocatalytic activities

Novel Pd/InVO₄-TiO₂ thin films with visible light photocatalytic activity were synthesized from the Pd and InVO₂ co-doped TiO₂ sol via sol-gel method. The photocatalytic activities of Pd/InVO₄-TiO₂ thin films were investigated based on the oxidative decomposition of methyl orange in aqueous solution. The as-prepared samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption spectroscopy (UV-vis). The results indicate that the Pd/InVO₄-TiO₂ thin films are compact, uniform and consist of sphere nanoparticles with diameters about 80-100 nm. The UV-vis spectra show that the Pd/InVO₄-TiO₂ thin films extend the light absorption spectrum toward the visible region. XPS results reveal that doped Pd exist in the form of metallic palladium. The photocatalytic experiments demonstrate that Pd doping can effectively enhance the photocatalytic activities of InVO₄-TiO₂ thin films in decomposition of aqueous methyl orange under visible light irradiation. It has been confirmed that Pd/InVO₄-TiO₂ thin films could be excited by visible light (E < 3.2 eV) due to the existence of the Pd and InVO₄ doped in the films.     

过渡金属(Fe,Co,Ni,Zn)掺杂金红石TiO2的电子结构和光学性质

采用基于密度泛函理论的第一性原理方法对未掺杂以及不同浓度过渡金属Fe,Co,Ni,Zn掺杂金红石TiO₂的超晶胞体系进行了几何优化,并讨论了其晶格常数,电子能带结构和光学性质.研究结果表明:掺杂前后的晶格参数与实验值偏差在3.6%以下;适量的过渡金属掺杂不但影响体系能带结构,拓宽光吸收范围,而且扮演着俘获电子的重要角色,有利于光生电子-空穴对的有效分离以及增强光吸收能力;Fe,Co,Ni,Zn最佳理论掺杂体系分别为Ti_0.75Fe_0.25O₂,Ti_0.75Co_0.25O₂,Ti_0.75Ni_0.25O₂,Ti_0.83Zn_0.17O₂;Fe,Co,Ni3d态分裂为t_2g和e_g态,分别贡献于价带高能级和导带低能级部分,促进了电子-空穴对的生成,从而可提高TiO₂的光催化性能;Zn3d态电子成对填满轨道,不易被激发,故光催化活性无明显提高.