Solid‐state NMR as a tool to describe and quantify the morphology of photoactive layers used in plastic solar cells

The optimization and control of the nanomorphology of thin films used as active layer in bulk heterojunction (BHJ) plastic solar cells is of key importance for a better understanding of the photovoltaic mechanisms and for increasing the device performances. Hereto, solid‐state NMR relaxation experiments have been evaluated to describe the film morphology of one of the “work‐horse” systems poly(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene‐vinylene)/[6, 6]‐phenyl‐C₆₁butyric acid methyl ester (MDMO‐PPV/PCBM) in a quantitative way. Attention is focused on the influence of the processing solvent (toluene vs. chlorobenzene), the blend composition, and the casting technique, that is, spin coating versus doctor blading. It is demonstrated that independently of the solvent and casting technique, part of the PCBM becomes phase separated from the mixed phase. Whereas casting from toluene results in the development of well‐defined PCBM crystallites, casting from chlorobenzene leads to the formation of PCBM‐rich domains that contain substructures of weakly organized PCBM nanoclusters. The amount and physico‐chemical state of the phase separated PCBM is quantified by solid‐state NMR relaxation times experiments. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Morphology and Performance of Poly(2-methoxy-5-(20-ethyl-hexyloxy)-p-phenylenevinylene) (MEH-PPV)∶(6,6)-Phenyl-C61-butyric Acid Methyl Ester (PCBM) Based Polymer Solar Cells

Polymer solar cells were fabricated based on composite films of poly(2‐methoxy‐5‐(2′‐ethyl‐hexyloxy)‐1,4‐phenylenevinylene) (MEH‐PPV):fullerene derivative (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) with weight blend ratio of 1:3, 1:4 and 1:5, spin‐coated from chloroform (CF), chlorobenzene (CB), and o‐dichlorobenzene (ODCB) solutions, respectively. Photoinduced current and power conversion efficiency (PCE) of the devices show a dependence on the solvents. The solar cells have the highest PCE at 1:5 blend ratio. Transmission electron microscopy (TEM) morphology reveals that there are some voids in MEH‐PPV:PCBM films. The void number decreases with the solvent from CF to CB and ODCB. We found the voids are located at the bottom of the films through electron tomography technique by TEM and film bottom‐side morphology study by atomic force microscopy. The charge carrier transport efficiency and collection efficiency should decrease greatly due to the voids, and the more voids the film has, the more degree the efficiencies decrease. PCE of the solar cell prepared from CF is lower than that of the solar cells prepared from CB and ODCB. The void phenomenon of MEH‐PPV:PCBM based solar cell and method to investigate the void position provide an experimental evidence and research mentality to fabricate polymer solar cell with high performance.     

Polymer BHJ solar cell performance tuning by C60 fullerene derivative alkyl side‐chain length

A systematic study on the influence of the alkyl side‐chain length of C₆₀ based fullerene derivatives in polymer solar cells based on an anthracene‐containing poly(p‐phenylene‐ethynylene)‐alt‐poly(p‐phenylene‐vinylene) (PPE‐PPV) copolymer (AnE‐PV) is reported. It is shown that the alkyl side‐chain length of the fullerene derivative strongly correlates with the individual photovoltaic parameters. The most pronounced dependence on the side‐chain length is found for the fill factor, spanning the range between 50–72%, which dominantly controls in combination with the short‐circuit current the power conversion efficiency. The maximum performance of 4.8% was found for an ethyl terminated side‐chain, whereas larger alkyl groups resulted in a gradually decreasing power conversion efficiency. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Decreased domain size and improved crystallinity by adjusting solvent–polymer interaction parameters in all‐polymer solar cells

We have investigated the effect of solvent–polymer interaction on the morphology, crystallinity, and device performance of poly‐(3‐hexylthiophene) (P3HT) and poly{2,7‐(9,9‐didodecyl‐fluorene)‐alt‐5,5‐[4′,7′‐bis(2‐thienyl)‐2′,1′,3′‐benzothia‐diaole]} (PF12TBT) blend system. 3‐Hexylthiophene (3‐HT), which had the similar structural units with both donor and acceptor materials, was chosen as the solvent additive to be added into the main solvent chlorobenzene (CB), to adjust the solvent–polymer interaction. With the 3‐HT percentage increasing from 5 to 30% in CB solution, the solvent–polymer interaction between polymer and solvent molecules decreased slightly according to the calculated solubility parameters (δ) and interaction parameters (χ₁₂). As a result, nanoscale phase‐separated and interconnected morphology with decreased domain size of both donor and acceptor was formed. Meanwhile, the order of P3HT molecule was enhanced which resulted from the extended film drying time and increased molecular planarity after incorporation of 3‐HT. The power conversion efficiency (PCE) had a gradual improvement to 1.08% as the 3‐HT percentage reached 10%, which can be attributed to the enhanced short‐circuit current (J_sc) and fill factor (FF). However, when the 3‐HT percentage exceeded 20%, the decreased J_sc and FF ultimately decreased the PCE. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 288–296     

Copoly(p‐phenylene)s containing bipolar triphenylamine and 1,2,4‐triazole groups: Synthesis,optoelectronic properties,and applications

Two novel copoly(p‐phenylene)s ( P1 – P2 ) containing bipolar groups (12.8 and 6.8 mol %, respectively), directly linked hole transporting triphenylamine and electron transporting aromatic 1,2,4‐triazole, were synthesized to enhance electroluminescence (EL) of poly(p‐phenylene vinylene) (PPV) derivatives. The bipolar groups not only enhance thermal stability but also promote electron affinity and hole affinity of the resulting copoly(p‐phenylene)s. Blending the bipolar copoly‐(p‐phenylene)s ( P1 – P2 ) with PPV derivatives ( d6‐PPV ) as an emitting layer effectively improve the emission efficiency of its electroluminescent devices [indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene) (PEDOT):poly(styrenesulfonate) (PSS)/polymer blend/Ca (50 nm)/Al (100 nm)]. The maximum luminance and maximum luminance efficiency were significantly enhanced from 310 cd m^?2 and 0.03 cd A^?1 ( d6‐PPV ‐based device) to 1450 cd m^?2 and 0.20 cd A^?1 (blend device with d6‐PPV / P1 = 96/4 containing ～0.5 wt % of bipolar groups), respectively. Our results demonstrate the efficacy of the copoly(p‐phenylene)s with bipolar groups in enhancing EL of PPV derivatives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

NMR study of the nanomorphology in thin films of polymer blends used in organic PV devices: MDMO‐PPV/PCBM

The disclosure of the nanomorphology of thin films in organic solar cells, prepared from blends of conjugated polymers and PCBM, is of key importance for a better understanding of the occurring photovoltaic (PV) mechanisms. Hereto solid‐state NMR relaxometry has been evaluated as a complementary technique to traditional microscopic techniques like atomic force microscopy and transmission electron microscopy. It is demonstrated that proton wide‐line solid‐state NMR relaxometry is a useful and innovative tool to study the phase morphology of blends used in semi‐conducting polymer based PV devices. Attention is focused on the influence of the blend composition and casting conditions on the resulting phase morphology. Two different casting techniques, i.e. spincoating and Doctor Blading, were compared. To demonstrate the applicability of NMR relaxometry in this field, MDMO‐PPV/PCBM blends where used, since these are known for their significant phase separation behavior in combination with toluene as solvent. In films prepared from blends in toluene with a PCBM content ≥70 wt %, a fraction of the PCBM is phase separated into crystalline domains, whereas the remaining part remains homogeneously mixed with the MDMO‐PPV. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 138–145, 2008     

Studies on molecular composite. I. Processing of molecular composites using a precursor polymer for poly(p‐phenylene benzobisthiazole)

The blending of a precursor polymer for poly(p‐phenylene benzobisthiazole) (PBZT) with various matrix polymers was attempted, followed by heat conversion of the PBZT precursor polymer to obtain molecular composites consisting of PBZT and the matrix polymers. A higher concentration of mixed solution using organic solvent and milder conditions to remove the solvent could be applied to blend the polymers using the precursor polymer in place of rodlike PBZT. The dispersibility of PBZT in the matrix polymer in the blended materials obtained depended on the ability to form intermolecular hydrogen bridges between the PBZT precursor and the matrix polymer. In particular, the blended material, obtained using a nonthermoplastic aromatic polyamide as the matrix polymer having a molecular structure similar to that of the PBZT prepolymer, was transparent and showed excellent reinforcing efficiency of PBZT. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 189–197, 1999     

Synthesis of all‐conjugated poly(3‐hexylthiophene)‐block‐ poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) and its blend for photovoltaic applications

New all‐conjugated block copolythiophene, poly(3‐hexylthiophene)‐block‐poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) (P3HT‐b‐P3PyT) was successfully prepared by Grignard metathesis polymerization. The supramolecular interaction between [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and P3PyT was proposed to control the aggregated size of PCBM and long‐term thermal stability of the photovoltaic cell, as evidenced by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and optical microscopy. The effect of different solvents on the electronic and optoelectronic properties was studied, including chloroform (CL), dichlorobenzene (DCB), and mixed solvent of CL/DCB. The optimized bulk heterojunction solar cell devices using the P3HT‐b‐P3PyT/PCBM blend showed a power conversion efficiency of 2.12%, comparable to that of P3HT/PCBM device despite the fact that former had a lower crystallinity or absorption coefficient. Furthermore, P3HT‐b‐P3PyT could be also used as a surfactant to enhance the long‐term thermal stability of P3HT/PCBM‐based solar cells by limiting the aggregated size of PCBM. This study represents a new supramolecular approach to design all‐conjugated block copolymers for high‐performance photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

4,9‐Dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione functionalized copolymers for organic photovoltaic devices

The synthesis of conjugated polymers 1 – 5 functionalized with 4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione in the backbone is reported and their use in the construction of organic solar cells is demonstrated. Increasing the molar ratio of 2,7‐dibromo‐3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione, relative to 4,4′‐dihexyl‐5,5′‐dibromo‐2,2′‐bithiophene, in the copolymer synthesis significantly lowers the solubility of these polymers. The incorporation of highly conjugated 3,8‐dihexyl‐4,9‐dihydro‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene‐4,9‐dione unit into the polymer backbone has been confirmed by UV–vis absorption. The observation of decreasing quantum yield for the emission in the order of 1 , 2 , 3 is consistent with copolymers with different comonomer content. The power conversion efficiencies of solar cells using blends of these polymers with PCBM ([6,6]‐phenyl C₆₁‐butyric acid methyl ester) were determined to be 0.11% for polymer 1 , 0.33% for 2 , and 0.26% for 3 , respectively. Under identical white light illumination, the power conversion efficiency of the device based on polymer 2 /PCBM as the active layer was three times higher compared to that of device based on polymer 1 /PCBM. Owing to the limited solubility and poor film‐forming ability of polymer 3 , the power conversion efficiency of solar cell based on 3 /PCBM blend is lower than that of 2 /PCBM blend, but is still larger than that of 1 /PCBM blend. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2680–2688, 2008     

Understanding of morphology evolution in local aggregates and neighboring regions for organic photovoltaics

Fluorescence intensity and its ratio mapping combined with time-dependent optical microscopy and atomic force microscopy (AFM) were used to understand morphology evolution of local aggregates and neighboring regions for organic solar cells. Three solvents with different boiling points including chlorobenzene (CB), 1,3-dichlorobenzene (1,3-DCB) and 1,2-dichlorobenzene (1,2-DCB) were used to engineer morphology. These solvents affected morphology evolution factors such as solvent evaporation rate, formation (e.g., growth rate, size and/or quantity) of (6,6)-phenyl-C61-butric-acid methyl ester (PCBM)-rich aggregates, and packing/ordering of poly(3-hexylthiophene) (P3HT). Three local regions (1, 2 and 3) including microscale aggregates and their surrounding areas were identified to explore the mechanism of morphology evolution. Region 1 was the PCBM-rich aggregates; region 2 was the PCBM-deficient area; and region 3 was the area composed of a relatively normal P3HT/PCBM composite beyond region 2 for each solvent. The intensity of fluorescence spectra decreased as region 1 > region 2 > region 3 in thermally annealed (140 °C, 20 min) P3HT/PCBM blend film from each solvent. The highest fluorescence intensity in region 1 was probably caused by the relatively poor phase separation where both PCBM and P3HT formed large isolated domains. The higher fluorescence intensity ratio (720 nm/650 nm) suggested a larger relative amount of PCBM molecules, supported by similar morphologies in fluorescence intensity ratio mapping compared to those in optical images. The fluorescence intensity ratio was with the order of region 1 > region 3 > region 2 in both CB and 1,3-DCB based films, but with region 1 > region 2 > region 3 for the 1,2-DCB based film. The order of effective area taken up by aggregates was CB > 1,3-DCB > 1,2-DCB in annealed (140 °C, 10 min) bulk blend films. The final solar cell performance agreed with morphology results. This work is imperative with regards to revealing the mechanism of morphology evolution in local aggregates and surrounding regions for organic photovoltaic films.     

Structure modification and annealing effect of polymer bulk heterojunction solar cells based on polyfluorene derivatives

Three low bandgap polyfluorene copolymers containing a donor–acceptor–donor moiety have been synthesized via Suzuki and Stille polymerization reactions. Their bandgaps and molecular energy levels (highest occupied molecular orbital and lowest unoccupied molecular orbital) varied with different polymerization methods. The molecular weight of the copolymer increased significantly through copolymerizing with a monomer having a long alkyl side chain. In order to investigate their photovoltaic properties, polymer solar cell devices based on the copolymers were fabricated with a structure of indium tin oxide/poly(styrene sulfonic acid)‐doped poly(ethylene dioxythiophene)/copolymers:[6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM)/LiF/Al under the illumination of AM 1.5G, 100 mW/cm². We found that the annealing temperature had a profound effect on the power conversion efficiency (PCE) of the devices with a blend of poly[9,9‐didodecylfluorene‐alt‐(bis‐thienylene) benzothiadiazole] (PF12‐TBT) and PCBM. The PCE of the solar cell based on PF12‐TBT/PCBM (1:4) annealing at 70 °C for 20 min was 4.13% with an open‐circuit voltage (V_oc) of 1.02 V, fill factor of 55.9%, and a short‐circuit current (J_sc) of 7.24 mA/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of low‐bandgap cyclopentadithiophene‐biselenophene copolymer and its use in field‐effect transistor and polymer solar cells

Novel series of conjugated copolymers, incorporating cyclopentadithiophene (CPDT) and the biselenophene ( R‐CPDT‐Se2 ), were synthesized by Pd‐catalyzed Stille coupling polymerization. The optical, electrochemical, field‐effect carrier mobilities, and photovoltaic properties of the R‐CPDT‐Se2 were investigated and compared with cyclopentadithiophene (CPDT) and the bithiophene ( EHex‐CPDT‐T2 ). The highest hole mobility of thin film transistor devices fabricated with new p‐type polymer semiconductors, Oct‐CPDT‐Se2 , was 1.3 × 10^?3 cm²/Vs with an on/off ratio of about 10⁵. The maximum power conversion efficiency of polymer solar cell fabricated with the blend of EHex‐CPDT‐Se2 /C₇₁‐PCBM reached 1.86% with an open circuit voltage (V_OC) of 0.55 V, a short circuit current density (J_sc) of 7.27 mA/cm², and a fill factor (FF) of 0.47 under AM 1.5G irradiation (100 mW/cm²). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Dual length morphological model for bulk‐heterojunction,polymer‐based solar cells

We present a dual length morphological model for the active layer of bulk‐heterojunction, polymer‐based solar cells using results from neutron and X‐ray scattering techniques. Two critical characteristic lengths are found in the mixtures composed of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C61‐butyric acid methyl ester (PCBM). A characteristic length at 15 nm is the local characteristic of the P3HT crystals and PCBM agglomerations, which is independent of the bulk composition upon relaxation by thermal annealing. Conversely, a larger bicontinuous structure described by Teubner–Strey model with phase distances between 23 and 35 nm forms only after thermal annealing, which is highly correlated to the bulk compositions. These results suggest phase separation between the polymer and fullerene can only be partially manipulated by simple processing techniques such as coating conditions and annealing, and a more rigorous design of the morphology should be implemented in the future. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym. Phys. 2014 , 52, 387–396     

Effects of amorphous poly(3‐hexylthiophene) on active‐layer structure and solar cells performance

A key challenge to the development of polymer‐based organic solar cells is the issue of long‐term stability, which is mainly caused by the unstable time‐dependent morphology of active layers. In this study, poly(3‐hexylthiophene) (P3HT)/[6,6]‐phenyl C60‐butyric acid methyl ester (PCBM) blend is used as a model system to demonstrate that the long‐term stability of power conversion efficiency can be significantly improved by the addition of a small amount of amorphous regiorandom P3HT into semicrystalline regioregular one. The optical properties measured by UV–vis absorption and photoluminescence reveal that regiorandom P3HT can intimately mix with PCBM and prevent the segregation of PCBM. In addition, X‐ray scattering techniques were adopted to evidence the retardation of phase separation between P3HT and PCBM when regiorandom P3HT is added, which is further confirmed by optical microscopy that shows a reduction of large PCBM crystals after annealing at high temperature in the presence of regiorandom P3HT. The improvement of the long‐term stability is attributed to the capability of amorphous P3HT to be thermodynamically miscible with PCBM, which allows the active layer to form a more stable structure that evolves slower and hence decelerates the device decay. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 975–985     

Poly(p‐phenylene methylene)‐based block copolymers by mechanistic transformation

The synthesis of poly(p‐phenylene methylene) (PPM)‐based block copolymers such as poly(p‐phenylene methylene)‐b‐poly(ε‐caprolactone) and poly(p‐phenylene methylene)‐b‐polytetrahydrofuran by mechanistic transformation was described. First, precursor PPM was synthesized by acid‐catalyzed polymerization of tribenzylborate at 16 °C. Then, this polymer was used as macroinitiators in either ring‐opening polymerization of ε‐caprolactone or cationic ring‐opening polymerization of tetrahydrofuran to yield respective block copolymers. The structures of the prepolymer and block copolymers were characterized by GPC and ¹H NMR investigations. The composition of block copolymers as determined by ¹H NMR and TGA analysis was found to be in very good agreement. The thermal behavior and surface morphology of the copolymers were also investigated, respectively, by differential scanning calorimetry and atomic force microscopy measurements, and the contribution of the major soft segment has been observed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Porphyrin–diindenothieno[2,3‐b]thiophene alternating copolymer—a blue‐light harvester in ternary‐blend polymer solar cells

Porphyrin, despite chosen by Nature as light harvesting units, hasn't revealed its full potentials as a structural unit in porphyrin‐incorporated polymers (PPors). A novel PPor was synthesized to investigate the origins of the low performances of PPor‐based polymer solar cells (PSCs). The polymer features broad absorption in the blue‐light region, because the diindenothieno[2,3‐b]thiophene (DITT) unit extended the conjugation in the polymer backbone. PPor‐DITT/PC₇₁BM based PSCs have a high V_oc (0.79 V). Their low J_sc and fill factor (FF) were attributed to the un‐optimized morphology, as indicated by the photoluminescence quenching and atomic force microscopy (AFM) experiments. Using PPor‐DITT as a blue‐light harvesting dopant in an amorphous host leverage the strong 400–550 nm absorption of PPor‐DITT and circumvent the difficulties in reaching optimized morphology in the PPor/PCBM thin films. An addition of 2 wt % of PPor‐DITT in ternary‐blend PSCs resulted in a 10 % increase of external quantum efficiency (EQE) in the blue‐light region. However, in a crystalline host, the dopant decreased the crystallinity of the host and led to large drops in FF and power conversion efficiencies (PCEs). The study provides an alternative route and expands the application of PPors in PSCs as a blue‐light harvester in ternary‐blend PSCs using amorphous polymers as host. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Controlled self‐assembly of porphyrin/fullerene donor–acceptor complex in a polymer thin film

Thin films composed of polycyclohexane (PCHE), zinc(II)‐5,10,15,20‐tetra‐(2‐naphthyl)porphyrin (ZnTNpP), and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) blends are prepared to investigate their potential for the controlled self‐assembly of a porphyrin/fullerene donor–acceptor complex in a polymer thin film. The compatibilities of PCHE/PCBM (p), PCHE/ZnTNpP (q), and ZnTNpP/PCBM (r) in these blends have a significant effect on the dispersion of the ZnTNpP/PCBM donor–acceptor complex in the PCHE thin film. When the compatibilities are p << q, r, and q ≈ r, the ZnTNpP/PCBM donor–acceptor complex is formed between the PCHE and PCBM phases. This concept to form a controlled self‐assembly of the ZnTNpP/PCBM donor–acceptor complex may be applied to various combinations of porphyrin/fullerene systems in polymer thin film solar cells to achieve excellent performance. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 743–746     

Molecular orientation and composition at the surface of spin‐coated polyfluorene:Fullerene blend films

The surface composition in spin‐coated films of polyfluorene:fullerene blends was determined quantitatively by near‐edge X‐ray absorption fine structure (NEXAFS) spectroscopy. By comparing partial and total electron yield spectra, we found vertical compositional differences in the surface region. Furthermore, the orientation of the polymer chains was investigated by variable‐angle NEXAFS. Blend films of poly[(9,9‐dioctylfluorenyl‐2,7‐diyl)‐co‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole] with [6,6]‐phenyl‐C61‐butyric acid methyl ester in two different blend ratios were studied. Results showed polymer enrichment of the surfaces for films with a polymer:fullerene weight ratio of 20:80 and of 50:50, spin‐coated from both chlorobenzene and chloroform solutions. The angular dependence of the NEXAFS spectra of the pure polymer films showed a preferential plane‐on orientation, which was slightly stronger in the subsurface region than at the surface. In blend films, this orientational preference was less pronounced and the difference between surface and subsurface vanished. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Comparison of two types of vertically aligned ZnO NRs for highly efficient polymer solar cells

Vertically aligned ZnO nanorods (NR) are prepared by two different syntheses methods and applied on polymer solar cells (PSCs). The ZnO electrodes work as the electron transport layer with the P3HT:PCBM blend acting as the active material. Several organic blend solution conditions are optimized: concentration, solvent, and deposition speed. The effect of different NR electrode morphologies is analyzed on the solar cell performance and characterized by current–voltage curves and IPCE analyses. The photovoltaic performance of the solar cells was observed to be influenced by many factors, among them infiltration of the organic P3HT:PCBM blend within the ZnO NR layer. The infiltration of the active layer was monitored by cross section SEM and energy dispersive X-ray spectroscopy analyses. Our results show that higher power conversion efficiencies are achieved when shorter NRs lengths are applied. The best power conversion efficiency obtained was 2.0% for a 400 nm ZnO NR electrode. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Effect of multiple adduct fullerenes on charge generation and transport in photovoltaic blends with poly(3‐hexylthiophene‐2,5‐diyl)

The effect of replacing [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) by its multiadduct analogs (bis‐PCBM and tris‐PCBM) in bulk heterojunction organic solar cells with poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) is studied in terms of blend film microstructure, photophysics, electron transport properties, and device performance. Although the power conversion efficiency of the blend with bis‐PCBM is similar to the blend with PCBM, the performance of the devices with tris‐PCBM is considerably lower as a result of small photocurrent. Despite the lower electron affinity of the fullerene multiadducts, μs‐ms transient absorption measurements show that the charge generation efficiency is similar for all three fullerenes. The annealed blend films with multiadducts show a lower degree of fullerene aggregation and lower P3HT crystallinity than the annealed blend films with PCBM. We conclude that the reduction in performance is due largely to poorer electron transport in the blend films from higher adducts, due to the poorer fullerene network formation as well as the slower electron transport within the fullerene phase, confirmed here by field effect transistor measurements. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010