用于液压传感的双芯光子晶体光纤

采用全矢量有限元方法进行光纤设计优化,得到横截面上失去两层空气洞的双芯光子晶体光纤,可用于液压传感.优化的双芯光子晶体光纤的模场半径和数值孔径与单模光纤基本一致,在优化的双芯光子晶体光纤和单模光纤之间有一个相对较低的熔接损耗.计算结果表明由模场半径和数值孔径导致的不匹配造成的总共损耗可低至0.026 dB,低于传统光子晶体光纤和单模光纤0.1 dB的直接熔接损耗.对基于20 cm双芯光子晶体光纤的液压传感器的性能进行研究,结果表明在0～500 MPa量程内的灵敏度为-1.6 pm/MPa.     

Guiding Properties of a Tapered Photonic Crystal Fiber Compared with Those of a Tapered Single-Mode Fiber

We have fabricated tapered photonic crystal fibers using a fusion splicer and experimentally observed the near-field mode distribution and the beam divergence of it. We have also compared characteristics of the tapered photonic crystal fiber with those of a tapered standard single-mode fiber. Unlike a tapered standard single-mode fiber, the mode field profile of a tapered photonic crystal fiber shows a good confinement of its field within the core region. The numerical apertures of tapered photonic crystal fibers are increased as the diameter of the fiber is decreased.     

应用于液压传感的光子晶体光纤特性

为实现结构紧凑、高灵敏度的光纤压力(液压)传感器,提出了一种应用于液压传感的边孔结构光子晶体光纤.基于全矢量有限元方法,研究了传统光子晶体光纤和边孔结构光子晶体光纤的有效折射、模式等特性以及在液压情况下的应力和应力特性.根据光弹效应给出了传统光子晶体光纤和边孔结构光子晶体光纤在液压情况下的折射率变化特性.模拟结果表明边孔结构光子晶体光纤可以获得更大的液压传感灵敏度,增大边孔半径可以提高液压传感灵敏度,因此结构优化的边孔结构光子晶体光纤可以实现高灵敏度的光纤压力(液压)压力传感器.     

Guiding Properties of a Tapered Photonic Crystal Fiber Compared with Those of a Tapered Single-Mode Fiber

We have fabricated tapered photonic crystal fibers using a fusion splicer and experimentally observed the near-field mode distribution and the beam divergence of it. We have also compared characteristics of the tapered photonic crystal fiber with those of a tapered standard single-mode fiber. Unlike a tapered standard single-mode fiber, the mode field profile of a tapered photonic crystal fiber shows a good confinement of its field within the core region. The numerical apertures of tapered photonic crystal fibers are increased as the diameter of the fiber is decreased.     

Impact of interstitial air holes on a wide-bandwidth rejection filter made from a photonic crystal fiber

We have investigated the spectral properties of a band rejection filter made with a long-period fiber grating written in photonic crystal fiber that has interstitial air holes. Experiments showed that only one mode was coupled strongly to the fundamental core mode over a 600 nm spectral range. The central wavelength of the filter could be tuned over that range without being appreciably affected by any other mode. By using the multipole method, we found that the interstitial air holes of the photonic crystal fiber played a critical role in limiting the number of modes that could strongly interact with the fundamental mode and in obtaining well-separated resonance peaks. Excellent agreement between theory and experiment was obtained.     

应用于液压传感的光子晶体光纤特性

为实现结构紧凑、高灵敏度的光纤压力(液压)传感器,提出了一种应用于液压传感的边孔结构光子晶体光纤.基于全矢量有限元方法,研究了传统光子晶体光纤和边孔结构光子晶体光纤的有效折射、模式等特性以及在液压情况下的应力和应力特性.根据光弹效应给出了传统光子晶体光纤和边孔结构光子晶体光纤在液压情况下的折射率变化特性.模拟结果表明边孔结构光子晶体光纤可以获得更大的液压传感灵敏度,增大边孔半径可以提高液压传感灵敏度,因此结构优化的边孔结构光子晶体光纤可以实现高灵敏度的光纤压力(液压)压力传感器.     

光子晶体光纤布拉格光栅传输谱特性的分析

研究光子晶体光纤中光纤光栅的传输谱特性对于研制基于光子晶体光纤的光纤光栅器件有着重要的意义。结合耦合模理论和光束传输相关函数方法,对一种典型光子晶体光纤中的布拉格光栅(FBG)传输谱进行了理论分析。比较了光子晶体光纤中布拉格光栅与常规布拉格光栅的传输谱。数值分析了光纤截面结构变化对于光栅传输谱的影响,并给出这种影响的定性解释。计算结果显示,与常规光纤光栅相比,包层模共振引起的损耗峰与正反向纤芯模耦合引起的损耗峰可以相比拟,而包层模共振的间隔也比常规光纤中光纤光栅的包层模共振间隔要大。同时给出了晶体光纤截面上空气孔的占空比,空气孔的排布层数对于传输谱影响的规律。     

矩形孔光子晶体光纤

采用全矢量有限元方法和完美匹配层条件,研究了一种在光纤包层中引入矩形孔的光子晶体光纤,提出一种实现高双折射光子晶体光纤的方法.模拟结果表明矩形孔光子晶体光纤具有椭圆孔光子晶体光纤类似的高双折射特性,其双折射高达0.01的量级,两种光子晶体光纤的模场、双折射、约束损耗等特性基本类似.     

一种高双折射光子晶体光纤模场和偏振特性的研究

采用平面波展开法分析一种填入了聚甲基丙稀酸甲酯并引入大空气孔的高双折射光子晶体光纤的模场和偏振特性,并研究其结构参数变化对偏振特性的影响。研究表明这种高双折射光纤的基模模场具有较强的线偏振特性,模式双折射比普通光子晶体保偏光纤有较大提高。研究结果为光子晶体保偏光纤的开发制作提供了理论基础。     

Efficient input and output fiber coupling to a photonic crystal waveguide

The efficiency of evanescent coupling between a silica optical fiber taper and a silicon photonic crystal waveguide is studied. A high-reflectivity mirror on the end of the photonic crystal waveguide is used to recollect, in the backward-propagating fiber mode, the optical power that is initially coupled into the photonic crystal waveguide. An outcoupled power in the backward-propagating fiber mode of 88% of the input power is measured, corresponding to a lower bound on the coupler efficiency of 94%.     

高双折射光子晶体光纤中均匀布拉格光栅的特性

研究了具有高双折射的光子晶体光纤(HB PCF)中均匀布拉格光栅(FBG)的光谱特性。利用紧凑的超格子模型,对光子晶体光纤的传输特性进行分析,研究正向传输和反向传输的模式之间的耦合规律,从而研究写入光子晶体光纤中的均匀布拉格光栅的特性。首先给出具有C6v对称性的零双折射光子晶体光纤中光纤布拉格光栅的布拉格波长λB随光纤结构参量的变化规律;然后分析一种高双折射光子晶体光纤中的光纤布拉格光栅的光谱特性,高双折射使两个不同偏振态的反射峰分开较大;最后分析了一种常用的双模双折射光子晶体光纤中光纤布拉格光栅的光谱特性,LP01模和LPe11模的两个偏振态对应的反射谱都由于高双折射而分开。     

高功率光纤激光器全内反射型大模场光子晶体光纤设计

在高功率密度下产生的非线性效应和材料损伤等问题限制了光纤激光器输出功率的进一步提高。利用大模场光纤降低光纤能量密度,提高非线性阈值是一种最为直接和有效的手段。以空气孔尺寸为光波长量级的全内反射型光子晶体光纤为对象,采用等效折射率模型分析了光子晶体光纤的单模特性,利用有限元法分析了结构参数对光子晶体光纤的模场面积和色散等光束质量参数的影响。设计了一种工作波长为0.40~1.55μm,模场面积为112.74~258.87μm2,且在1.27μm附近可补偿色散的大模场光子晶体光纤。该研究可为高功率光纤激光器大模场光纤的进一步参数优化设计及元件加工提供重要参考。     

Fiber in-line Mach-Zehnder interferometer constructed by selective infiltration of two air holes in photonic crystal fiber

A fiber in-line Mach-Zehnder interferometer is fabricated through selective infiltrating of two adjacent air holes of the innermost layer in the solid core photonic crystal fiber, assisted by femtosecond laser micromachining. The liquid infiltrated has higher refractive index than that of the background silica, and, hence, the two rods created can support a guide mode with lower effective refractive index than that of silica. The interference is produced by the fiber fundamental mode and the guide mode. The free spectral range (FSR) of the interferometer is found to be dependent on the photonic crystal fiber length, and a large FSR corresponds to a short photonic crystal fiber length. Such an interferometer device is robust and exhibits extremely high temperature sensitivity (～7.3?nm/°C for the photonic crystal fiber length of 3.4?cm) and flexible operation capability.     

激光泵浦碲化物产生中红外超连续谱数值模拟

对2 m波段脉冲激光泵浦碲化物光子晶体光纤产生中红外超连续谱进行了数值研究。通过材料的拉曼增益谱间接求得了对应的拉曼响应函数;由光子晶体光纤的材料折射率和波导结构,通过COMSOL软件获得了碲化物光子晶体光纤中基模等效折射率,计算了相应的色散曲线和限制损耗 ;利用自适应的分步傅里叶算法,模拟了中心波长为1.96m、峰值功率为20 kW的50 fs脉冲光泵浦碲化物光子晶体光纤时超连续谱的产生,当光纤长度为6 cm时,产生的中红外超连续谱波长范围为1.0~4.5 m。     

Influence of a holey cladding structure on spectral characteristics of side-polished endlessly single-mode photonic crystal fibers

We experimentally investigate the spectral characteristics of side-polished endlessly single-mode photonic crystal fibers of different polishing depths and radii of curvature that are important to mode field diameter, evanescent coupling, waveguide losses, higher-order mode excitation, and dispersion slopes of photonic crystal fiber components. A polished photonic crystal fiber with a greater polishing depth or a larger radius of curvature shows a more dispersive characteristic. In contrast to conventional single-mode fibers, in photonic crystal fibers the evanescent field is more strongly localized, and the propagating light can be more efficiently guided within the deformed core.     

仿真在光子晶体光纤教学中的应用

光子晶体光纤(PCF),为《现代光纤通信技术》的其中一节,因光子晶体光纤包层中空气孔灵活的排列结构使得其呈现出许多在传统光纤中难以实现的特性。为了研究光子晶体光纤的特性,提出了采用数值软件仿真的实验教学模式,实践验证了可以在光子晶体光纤教学过程中有效的提高学生综合应用能力。     

A colloidal crystal microstructure fiber: fabrication and characterization

A method of fabricating colloidal crystal microstructured fiber is presented. The proposed structure relies on partial etching of the cladding layer of a single-mode fiber and growth of colloidal photonic crystals inside eroded area. The photonic crystal cylindrical annulus embedded in fiber is characterized by optical and scanning electron microscopy. The optical characterization was analyzed by optical transmission spectroscopy. The measurement results show a about 1550-nm band gap. The results also reveal the possibility of cladding cylindrical fibers with three-dimensional photonic crystals.     

Modification of spontaneous emission rate of micrometer-sized light sources using hollow-core photonic crystal fibers

We investigate numerically and experimentally the modification of the spontaneous emission rate for micrometer-sized light sources embedded in a hollow-core photonic crystal fiber (HCPCF). The diameter of the light source is deliberately chosen such that they could be easily introduced into the central hole of the hollow-core photonic crystal fiber by capillary force. The photoluminescence from the microparticles is measured by using an inverted microscope in combination with a spectrometer. The modification of the spontaneous emission rate is observed in a wavelength region where there is no band gap. The experimental observations are consistent with the simulation results obtained by the plane wave expansion and finite-difference time-domain techniques.     

Heat Treatment of the Photonic Crystal Fiber

We report heat treatment of the photonic crystal fiber. As the temperature was increased, the transmission of the photonic crystal fiber was increased, unlike conventional single mode fiber. The transmission increase at short wavelength region was larger than long wavelength region for the various temperatures. After crystallization of the silica glass, the spectra of the photonic crystal fiber were just decreased at all wavelength regions, but, in case of the single mode fiber, the absorption in visible region around 450 nm increased with increasing temperature.     

单模低损耗光子晶体光纤的设计及特性分析

设计了几种特殊结构的带隙光子晶体光纤,采用平面波展开法和频域有限差分方法研究了基于不同结构光子晶体光纤的带、模式、色散和色散斜率。由平面波展开法和频域有限差分方法求解麦克斯韦方程组导出本征值方程,可以得到带隙光子晶体光纤中可能存在的不同模式的传播常数、电场分布、本征频率和磁场分布。分别给出了第二圈填充率取三种不同值时带、模式、色散和色散斜率的变化。结果表明,当第二圈填充率改变时其特性有明显的变化。随着填充率从0．75减小到0．45,其二阶模分裂成两个类LP01模,可降低损耗。计算结果对单模和低损耗的光子晶体光纤的设计有参考价值。