对乙酰氨基酚在多壁碳纳米管修饰电极上的电化学行为

制备了多壁碳纳米管修饰玻碳电极,研究了对乙酰氨基酚在多壁碳纳米管修饰电极上的循环伏安行为,并建立了测定对乙酰氨基酚含量的电化学分析方法。在pH为6.89的磷酸盐缓冲液中,多壁碳纳米管修饰电极对对乙酰氨基酚有明显的电催化作用,其氧化峰电流与对乙酰氨基酚浓度在1.0×10-6～1.0×10-4mol·L-1范围内呈良好的线性关系,检测限为2.0×10-7mol·L-1。     

肾上腺素在多壁碳纳米管修饰金电极上的电化学行为及测定

报道了一种测定肾上腺素的化学修饰电极和电化学分析方法。与裸金电极相比,刚果红改性的多壁碳纳米管修饰金电极可显著提高肾上腺素的氧化峰电流。实验优化了底液、pH值、修饰剂量、富集电位和富集时间等条件,建立了一种直接测定肾上腺素的高灵敏的电化学分析方法。该方法测定肾上腺素的线性范围为4.0×10-7~2.0×10-4mol.L-1;富集30 s后的检出限为8.5×10-8mol.L-1;对2.0×10-5mol.L-1的肾上腺素平行测定10次的相对标准偏差为4.9%。此方法已成功用于盐酸肾上腺素注射液中含量的测定。     

聚赖氨酸/多壁碳纳米管修饰电极测定大米中的铅

通过滴涂及电聚合方式分别将多壁碳纳米管和赖氨酸共修饰于玻碳电极上,制备出聚赖氨酸/多壁碳纳米管修饰电极,并建立了阳极溶出伏安法测定铅离子的新方法。采用线性扫描伏安法及循环伏安法研究了铅离子在修饰电极上的电化学行为,并考察了测定底液、底液p H值、富集电位、富集时间等条件的影响。在最佳实验条件下,铅离子的溶出峰电流与其浓度在2.0×10-7~8.0×10-5mol·L-1范围内呈良好的线性关系,检出限为1.0×10-7mol·L-1。利用所制备的修饰电极对大米样品进行加标回收实验,回收率为98%~102%。该方法具有良好的灵敏度和稳定性,已成功应用于大米样品中铅离子的测定。     

多壁碳纳米管修饰玻碳电极测定铜离子

以多壁碳纳米管(MWCNTs)修饰玻碳电极为工作电极,采用阳极溶出线性扫描法研究了铜离子的电化学测定方法。探讨了MWCNTs修饰层数、富集电位、富集时间、溶液pH、支持电解质对峰电流的影响。实验表明,铜离子浓度在1.0×10-8~1.0×10-5mol·L-1范围内与峰电流呈良好的线性关系,检测限为2.0×10-9mol·L-1,且该电极具有良好的稳定性和抗干扰能力。     

多壁碳纳米管修饰电极测定非那西汀

本文研究了非那西汀在羧基化多壁碳纳米管修饰电极上的电化学行为。在0.1 mol·L-1HAc-NaAc(pH5.3)溶液中,非那西汀在羧基化多壁碳纳米管修饰电极上有一对可逆的氧化还原峰和一个氧化峰。对各种实验条件进行了优化,测得峰电流I p与非那西汀浓度在4.0×10-6~1.0×10-4mol·L-1范围内呈良好的线性关系,检测限为1.0×10-6mol·L-1。此修饰电极具有较好的重现性和稳定性。利用优化后的条件对尼美舒利药片进行了测定,测量值与标示值符合,回收率在96.5%~104.2%。     

聚磺基水杨酸/碳纳米管修饰电极在抗坏血酸共存时测定多巴胺

研究了聚磺基水杨酸/多壁碳纳米管修饰玻碳电极的制备及多巴胺在此修饰电极上的电化学行为, 讨论了修饰条件、扫速、溶液 pH 以及抗坏血酸的干扰对多巴胺在这种复合物电极上响应的影响. 在 pH 7.4 磷酸盐缓冲溶液中, 在1.0×10-3 mol/L 抗坏血酸共存的条件下, 多巴胺氧化峰电流与其浓度在 5×10-7～10-4 mol/L 范围内分段呈线性关系, 检出限为 1.0×10-7 mol/L. 结果表明: 聚磺基水杨酸/多壁碳纳米管修饰电极结合了多壁碳纳米管灵敏度高和聚磺基水杨酸选择性好的优点, 可用于抗坏血酸共存条件下多巴胺的测定.     

碳纳米管-离子液体-木质素磺酸钠复合物修饰电极同位镀铋膜测定水中铅和镉

采用涂覆法制备多壁碳纳米管(MWCNTs)-离子液体([BMIM]PF6)-木质素磺酸钠(LSS)修饰玻碳电极(GCE),然后在其表面同位镀铋膜,研究Pb(Ⅱ)和Cd(Ⅱ)在该修饰电极上的阳极溶出伏安行为。实验表明,Pb、Cd在该修饰电极上分别于-0.44V、-0.73V产生灵敏的溶出峰,Pb(Ⅱ)和Cd(Ⅱ)分别在3.0×10-8～1.0×10-6mol·L-1和2.0×10-8～8.0×10-7mol·L-1浓度范围内与其溶出峰电流呈良好的线性关系,检出限分别为4.1×10-9mol·L-1、6.9×10-9mol·L-1。该修饰电极制备简单,重现性好,用于河水中铅和镉的测定,效果良好。     

呋喃唑酮在多壁碳纳米管修饰电极上的电化学行为及分析应用

本文采用循环伏安法(CV)和差分脉冲伏安法(DPV),研究了呋喃唑酮(FZ)在多壁碳纳米管修饰玻碳电极(MWNTs/GCE)上的电化学行为。对影响该修饰电极电流大小的主要条件,如底液的pH值、富集电位和富集时间等进行了优化。结果表明:FZ在MWNTs/GCE上呈现不可逆的还原峰。与裸电极相比,FZ在修饰电极上的还原峰电流明显增大。在最佳的实验条件下,其峰电流随着FZ浓度的增加而增大,在4.9×10-7～5.9×10-5 mol.L-1范围内成线性关系,检测限低至8.0×10-8 mol.L-1。该修饰电极对FZ的测定表现出良好的重现性和稳定性,可用于药物制剂中FZ的定量测定。     

多壁碳纳米管-离子液体凝胶修饰电极对放线菌素D的高灵敏检测

以多壁碳纳米管和离子液体1-正丁基-3-甲基咪唑六氟磷酸盐(BMIMPF6)为修饰剂,研制了多壁碳纳米管-离子液体凝胶修饰玻碳电极(MWNTs-BMIMPF6/GCE),并研究了放线菌素D在该电极上的电化学行为。实验结果表明,放线菌素D于-0.09 V处有一明显的氧化峰,在pH=4.8的HAc-NaAc缓冲溶液中,放线菌素D在该修饰电极上产生的氧化峰电流比在多壁碳纳米管修饰玻碳电极上显著增大。在选定实验条件下,放线菌素D的氧化峰电流与其浓度在2.0×10-8~8.0×10-7mol/L的范围内呈良好的线性关系,检出限为7.5×10-9mol/L。该方法可用于注射液中放线菌素D的测定。     

碳纳米管修饰电极上沙丁胺醇电催化氧化研究

将多壁碳纳米管(MWNT)分散在疏水性表面活性剂双十六烷基磷酸(DHP)溶液中形成稳定、均相的分散液,然后制备多壁碳纳米管-DHP复合膜修饰玻碳电极(MWNT-DHP/GCE).应用方波伏安法研究了沙丁胺醇在修饰电极上的电化学行为,结果表明,碳纳米管复合膜修饰电极对沙丁胺醇的氧化有良好的电催化活性,其氧化反应为一电子一质子过程,氧化电位比裸玻碳电极负移40 mV,峰电流增加了4.5倍.在最佳测试条件下,氧化峰电流与沙丁胺醇浓度在8.3×10-7~3.3×10-6mol/L范围内呈良好线性关系,开路富集2min,检出限达1.8×10-7mol/L.该修饰电极具有良好的重现性、稳定性.     

The Colloidal Stabilization of Carbon with Carbon: Carbon Nanobubbles as both Dispersant and Glue for Carbon Nanotubes

The superior physical properties of carbon nanotubes (CNTs) have led to their broad application. Intrinsically, CNTs tend to agglomerate from hydrophobic interactions, which is highly undesirable for solution processing and device fabrication. Commonly, a stabilizer consisting of organic surfactants or polymers is used to disperse CNTs. Recently, we synthesized nitrogen‐doped carbon hollow nanospheres (25–90 nm), termed carbon “nanobubbles”. They bear superior dispersability in water and distinctive graphitic order. Herein, we describe the nanobubble‐assisted dispersion of CNTs in aqueous solution upon sonication. This process relies on the π–π interaction between the two aromatic carbon nanostructures, which can process their carbon mixture in water into conductive filter membranes, ink, and discs. This stabilization can be extended to other aromatic carbons. In addition, the π–π interaction may create a new type of carbon p–n junction that can be used to improve charge separation.     

一维新型碳的同素异形体:碳链

碳链是一种完全一维的、具有电子轨道sp杂化结构的新型碳的同素异形体.正是由于碳链的独特的一维结构,使其拥有区别于富勒烯、石墨烯和碳纳米管的化学键,从而表现出更加优异的性能,如:理论预言碳链的机械强度是石墨烯的几倍;碳链的导热也类似于石墨烯和碳纳米管;碳链是具有直接带隙的半导体材料,且带隙的大小可以通过其长度来调控,其长...     

Adsorption of Carbon Dioxide on Activated Carbon

The adsorption of CO2 on a raw activated carbon A and three modified activated carbon samples B, C, and D at temperatures ranging from 303 to 333 K and the thermodynamics of adsorption have been investigated using a vacuum adsorption apparatus in order to obtain more information about the effect of CO2 on removal of organic sulfur-containing compounds in industrial gases. The active ingredients impregnated in the carbon samples show significant influence on the adsorption for CO2 and its volumes adsorbed on modified carbon samples B, C, and D are all larger than that on the raw carbon sample A. On the other hand, the physical parameters such as surface area, pore volume, and micropore volume of carbon samples show no influence on the adsorbed amount of CO2. The Dubinin-Radushkevich (D-R) equation was the best model for fitting the adsorption data on carbon samples A and B, while the Preundlich equation was the best fit for the adsorption on carbon samples C and D. The isosteric heats of adsorption on carbon samples A, B, C, and D derived from the adsorption isotherms using the Clapeyron equation decreased slightly increasing surface loading. The heat of adsorption lay between 10.5 and 28.4 kJ/mol, with the carbon sample D having the highest value at all surface coverages that were studied. The observed entropy change associated with the adsorption for the carbon samples A, B, and C (above the surface coverage of 7 ml/g) was lower than the theoretical value for mobile adsorption. However, it was higher than the theoretical value for mobile adsorption but lower than the theoretical value for localized adsorption for carbon sample D.     

Growth of Single-walled Carbon Nanotubes on Substrates Using Carbon Monoxide as Carbon Source

The growth of single-walled carbon nanotubes(SWCNTs) on substrates has attracted great interests because of the potential applications in various fields. Carbon monoxide(CO) was used as the carbon source for the growth of SWCNTs on silicon substrates. Random or oriented SWCNTs can be produced by varying the CO flow rate. When the flow rate of CO was as low as 20 sccm(sccm:standard cubic centimeter per minute), dense SWCNT networks with clean surface were produced. When the flow rate was above 50 sccm, vertically aligned SWCNT(VA-SWCNT) arrays were grown. Well-aligned VA-SWCNT arrays were obtained in the temperature range of 650-800℃ and the content of large-diameter(above 1.7 nm) tubes in the array increased with the temperature. The height of the array was affected by the growth temperature, the CO flow rate, and the growth time. These findings indicate CO can be used as an efficient carbon source for the growth of SWCNTs on substrates under low flow rates.     

埃洛石纳米管模板法一步法制备一维碳纳米管/碳纳米棒混合纳米碳材料

利用埃洛石纳米管(HNTs)特有的中空纳米结构,以及丰富的界面化学性质,以聚乙烯醇(PVA)为碳源,采用浸渍填充纳米孔方法实现了一步制备一维碳纳米管(CNTs)/碳纳米棒(CNRs)混合纳米碳材料。考察模板剂(HNTs)和碳源(PVA)之间的比例关系对混合纳米碳材料的结构影响,利用XRD、FTIR、Raman、N2吸附-脱附测试、TEM、SEM以及电阻率和分散性等表征手段分析混合纳米碳材料的结构变化。结果发现,PVA填充含量的增加将导致产物中CNRs的质量分数增加;当PVA和HNTs质量之比为1∶1时,所制备的CNTs/CNRs的孔体积达到最大值2.142 cm~3·g-1,比表面积达到583 m~2·g-1,并且表现出较好的电导率和分散性,表明低的PVA填充比例制备的混合碳材料中CNTs含量较高。     

Carbon clusters

Some of the most significant discoveries and achievements concerning the mass spectra and gas phase ion chemistry of carbon clusters are reviewed. These include (1) nanosecond and femtosecond laser ionizations; (2) ion structures through ion/molecule reactions, ion chromatography, and computational methods; (3) carbon cluster cooling through radiative decay, dissociative decay, and thermionic emission; (4) mechanisms and energetics of fragmentation reactions; (5) endohedral fullerenes including recent data on ion beam implantation, and (6) ion chemistry as a function of the fullerene charge state.     

二氧化碳与低碳经济发展

由于二氧化碳无色无味,又存在于大气中,因此它在植物生长中的重要性被人类忽略了。其实二氧化碳是光合作用的反应物,是植物生长的重要原料;又是一种新型绿色肥料。人类应该着力开发以二氧化碳为原料的新型肥料发展低碳经济。     

Ni/γ-Al2O3催化剂上CH4-CO2重整体系中积碳-消碳的研究

用动态热重技术和色谱技术联用以及XRD和TEM等表征手段,研究了Ni/γ-Al     

Palladium-Catalyzed Addition of Carbon Monoxide and Carbon Tetrachloride to 1-Octene in Supercritical Carbon Dioxide

The Pd-catalyzed addition of carbon monoxide and carbon tetrachloride to 1-octene gave coadduct [alkyl 2-( 2, 2, 2-trichloroethyl)octanoate] as the major product in supercritical carbon dioxide by using pyridine as the base. It was found that the selectivity and the yield of coadduct were greatly affected by the pressure of carbon dioxide, the reaction temperature and the amounts of alcohol and base used.     

碳纳米管含量对炭炭复合材料组织及力学性能的影响

炭纤维上原位合成了均匀生长且具有伸张形貌的碳纳米管,借助化学气相渗透制备了碳纳米管增强的炭炭复合材料,研究了不同含量的碳纳米管对炭炭复合材料组织和力学性能的影响。结果表明：炭纤维上生长碳纳米管改变了热解炭的沉积行为,诱导了各向同性热解炭的生成,且随着碳纳米管含量的增加,各向同性热解炭的厚度增加,但是复合材料的d002值却明显降低。微量的碳纳米管即可显著提高复合材料的力学强度,随着其含量的增加,复合材料的力学强度和模量迅速提高,但材料的断裂行为却急剧恶化,断裂模式由最初的假塑性断裂转变为脆性断裂。