大孔吸附树脂纯化迷迭香脂溶性总酚酸的研究

从X-5、D4020、AB-8、H1020、NKA-Ⅱ、HPD-100A、SIPI、HPD800和D3520大孔吸附树脂中筛选出H1020树脂,研究了其对迷迭香脂溶性总酚酸的静态与动态吸附和解吸性能.结果表明,H1020树脂对迷迭香脂溶性总酚酸的饱和吸附量为19.84mg/g干树脂,饱和吸附时间为3h,适宜的解吸荆为体积分数90%的乙醇溶液;以质量浓度为4.45m/mL的迷迭香提取液上柱,流速为1.0mL/min,当吸附平衡后,2.7BV体积分数90%的乙醇溶液可将吸附的总酚酸完全洗脱.经动态纯化后,脂溶性总酚酸质量分数从47.74%提高到70.46%,该组分清除DPPH自由基的IC50值为0.0469mg/mL.     

离子交换法去除有机二胺吸收剂PA-A中SO42-的工艺研究

采用单因素实验法,考察了3种树脂对有机二胺吸收剂PA-A水溶液中SO42-的动态吸附-解吸性能,优化了树脂动态吸附-再生工艺.结果表明,D296型树脂具有良好的吸附选择性和较高的吸附容量;当流速为8.08BV/h、高径比为5.64、初始SO42-浓度为96.94g/L时,D296型树脂对PA-A水溶液中的SO42-动态饱和吸附量可达430.06mg/g干树脂;采用4％ NaOH水溶液在4.04BV/h的流速下对吸附饱和的树脂进行洗脱,再生率可达95％左右;树脂重复使用10次后其吸附-解吸性能基本不变.     

西索米星在大孔弱酸树脂上的吸附研究与传质系数的测定

对西索米星在大孔弱酸树脂上吸附平衡与动力学进行研究。建立了间歇吸附表面有效扩散模型,利用实验测定了吸附平衡曲线和吸附速率曲线,结合正交配置法、遗传算法直接拟合出固相粒内表面有效扩散系数Dc和液相传质系数kf,其拟合均方根误差不大于0.025。研究结果表明,西索米星在D113树脂上的吸附平衡符合Langmiur方程,吸附速率实验数据与吸附模型数值解拟合良好,表面有效扩散模型能够很好地描述西索米星在弱酸树脂D113上的吸附行为。在实验条件下,表面有效扩散系数Dc约为2.00×10-8~4.09×10-8cm2/s,液相传质系数kf约为9.00×10-5~2.95×10-4cm/s。     

西索米星在大孔弱酸树脂上的吸附研究与传质系数的测定

对西索米星在大孔弱酸树脂上吸附平衡与动力学进行研究。建立了间歇吸附表面有效扩散模型,利用实验测定了吸附平衡曲线和吸附速率曲线,结合正交配置法、遗传算法直接拟合出固相粒内表面有效扩散系数Dc和液相传质系数kf,其拟合均方根误差不大于0.025。研究结果表明,西索米星在D113树脂上的吸附平衡符合Langmiur方程,吸附速率实验数据与吸附模型数值解拟合良好,表面有效扩散模型能够很好地描述西索米星在弱酸树脂D113上的吸附行为。在实验条件下,表面有效扩散系数Dc约为2.00×10-8～4.09×10-8cm2/s,液相传质系数kf约为9.00×10-5～2.95×10-4cm/s。     

大孔阳离子交换树脂对井冈霉素的吸附研究

比较了5种大孔树脂与常用的001×4凝胶树脂对井冈霉素的静态和动态吸附的性能实验,并选择了其中几种有代表性的树脂,研究其对井冈霉素的吸附特性及其机理.采用正交试验筛选出具有较大吸附量的大孔强酸性阳离子树脂HD-8,并对其工艺条件进行了优化,其较优吸附能力为15.34mg/ml树脂h;同时考察了HD-8树脂的解吸行为,发现用1mol/L的氨水:80%乙醇=1:1洗脱率为98.8%,洗脱效果明显.     

丙烯酸Fe3+型树脂在非水介质中对鞣酸的配位吸附及洗脱性能

将Fe3 载于丙烯酸树脂上,制备了在非水介质中对鞣酸具有良好吸附性能的配位吸附树脂.在甲醇中,树脂对鞣酸的吸附符合Langmuir单分子层吸附模型,静态饱和吸附量为34mg/g,吸附为粒扩散控制过程.动态吸附中,树脂对鞣酸的泄漏吸附量为25mg/g,饱和吸附量32mg/g.采用5%的甲胺乙醇溶液作洗脱剂,洗脱率95%.树脂在吸附及洗脱过程中未见Fe3 脱落.     

酚醛型吸附树脂对茶碱的吸附性能研究

研究了酚醛型吸附树脂对茶碱的静态和动态吸附。结果表明3种树脂对茶碱的吸附量均达117－204mg/g，明显优于DuoliteS-761;酚醛型吸附树脂等温吸附茶碱的平衡吸附数据符合Langmuir方程，相关系数在0．99以上，因此，酚醛型吸附树脂吸附茶碱属单分子层吸附；用1mol/LHCl和W甲醇为80％复合溶液作为吸附树脂的洗脱剂，效果很好。     

D301R树脂吸附-解吸钼的行为研究

对D301R型阴离子交换树脂吸附-解吸钼的条件进行了研究，采用静态法试验了pH值、钼的浓度等因素对该树脂吸附钼的影响；采用动态法讨论了该树脂对钼的饱和吸附量、解吸剂及其浓度对解吸钼的影响。结果表明在pH2．5，钼的浓度为20g/L时吸附效果最好，树脂对钼的饱和吸附量为1020mg／g，而采用150g/L NaOH溶液解吸钼效果最佳。     

离子交换树脂的选择及柠檬酸溶液循环使用研究

用离子交换树脂法吸附柠檬酸溶液中的金属离子,苯乙烯系阳离子交换树脂的吸附性能较好,它对镍、铝离子的吸附容量均较大,且吸附前后柠檬酸溶液的浓度变化较小.静态条件下树脂对镍的吸附容量为16.83mg Ni/g干树脂,对铝为21.36mg Al/g干树脂;动态条件下树脂对镍的吸附容量为6.78mg Ni/g干树脂,对铝为31.8mgAl/g干树脂,吸附液流速为1m/h～3m/h.吸附后的柠檬酸溶液可循环使用.当用1mol/L硫酸解吸时,树脂对镍铝的解吸率可达90%以上.当硫酸中Ni2 为1.70mmol/L,Al3 为7.40mmol/L时,树脂的解吸率仍可达80%以上.     

酚醛型吸附树脂对咖啡因和茶碱吸附性能的研究

用静态和动态方法研究了酚醛型吸附树脂JDW-2和DuoliteS-761对咖啡因和茶碱的吸附行为.结果表明,自制树脂JDW-2对咖啡因和茶碱的吸附性能明显优于DuoliteS-761.树脂的比表面积、含水量、酚羟基的含量与吸附关系密切,尽管JDW-2的比表面积比DuoliteS-761小,但前者比后者具有更高的含水量(42%)和酚羟基含量(3.72mmol/g).在静态条件下,JDW-2吸附咖啡因的速率比DuoliteS-761快,JDW-2树脂对咖啡因和茶碱饱和吸附量分别为246和127mg/g干树脂,而DuoliteS-761树脂对它们的吸附量分别为121和53mg/g干树脂;JDW-2和DuoliteS-761吸附咖啡因的初始阶段是粒扩散控制过程;酚醛型吸附树脂等温吸附咖啡因和茶碱的平衡吸附数据符合Langmuir方程.酚醛型吸附树脂吸附咖啡因和茶碱属单分子层吸附.在动态条件下,1mol/LHCl和40%甲醇溶液以1.5BV/h来洗脱吸附咖啡因的JDW-2,在4～5个床体积的洗脱率分别是88%和93%,而1mol/LHCl和80%甲醇溶液以1.5BV/h来洗脱吸附茶碱的JDW-2,在3～4个床体积的洗脱率分别是91%和96%,表明酚醛型吸附树脂具有良好的洗脱性能,用1mol/LHCl和40%(或80%)甲醇溶液作复合洗脱剂从JDW-2中洗脱咖啡因(或茶碱),效     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.