Studies on the Phase Separation of Poly(Ether Imide)‐Modified Cyanate Ester Resin

Abstract

A high temperature thermosetting bisphenol‐A dicyanate (BADCy) was blended with a novel thermoplastic poly(ether imide) (PEI) at various composition. The phase separation behavior during isothermal curing was studied by differential scanning calorimeter (DSC), time‐resolved light scattering (TRLS), scanning electron microscopy (SEM), and rheological measurements. The results suggested that the phase structure changed from separated phase, via co‐continuous phase, to phase inversion with the increase of the PEI content. The curing conversion of BADCy was slightly affected by the composition in the blend and the curing rate was decreased with the increase of PEI content. The co‐continuous phase morphology was attributed to a spinodal decomposition. The initial concentration of PEI had an effect on the rheological behavior during phase separation. It was found by tensile test that the blend with 15 wt.% PEI had higher tensile strength and elongation at break than that without PEI.     

Correlative analysis between morphology and mechanical properties of poly-3-hydroxybutyrate (PHB) blended with polycarprolactone (PCL) using solid-state NMR

Blends of poly(3-hydroxybutyrate) (PHB) and poly(caprolactone) (PCL) were evaluated using multiscale instrumental analyses to reveal the effects of blend ratio and crosslinking reagent. In the multiscale instrumental analyses, molecular mobility from molecular to nano scales was examined by solid-state NMR, while the morphology at the micron scale was revealed by scanning electron microscopy (SEM). PHB-rich blends adopted a sea-island morphology and showed a larger maximum stress due to dispersed PHB filler. A PCL-rich blend also adopted a sea-island morphology but the sea domain consisted of PCL and showed a larger strain at break. An equal ratio PHB/PCL blend had a bicontinuous morphology which showed lower maximum stress and lower strain at break because of large hemispherical defects. The crosslinking reagent changes these heterogeneous morphologies of PHB/PCL blends to homogeneous at the micron scale, which improved tensile properties. Even though the molecular mobility changed with the polymer content and the crosslinking reagent, the bicontinuous and homogeneous morphologies more significantly affected the tensile properties of the PHB/PCL blends.     

PPEKK/PEI共混物的相容性及拉伸性能

作为相容体系 ,聚芳醚酮与聚醚酰亚胺 (ＰＥＩ)共混物体系的研究受到了研究者的重视[1～ 4] .由于现在已商品化的聚芳醚酮基本上都是半结晶型聚合物 ,所以有有关无定型聚芳醚酮与聚醚酰亚胺共混物的研究鲜见报道 .含二氮杂萘酮结构聚芳醚酮酮 (ＰＰＥＫＫ)是一种新型耐高温聚合物 ,相比于已经商品化的各种聚芳醚酮 ,ＰＰＥＫＫ除具有优异的综合性能外 ,它最大的特点表现在以下两方面 ,ＰＰＥＫＫ耐热性突出 ,玻璃化转变温度 (Ｔｇ)为 2 4 5℃左右 ,远高于各种商品化的聚芳醚酮 ;ＰＰＥＫＫ为无定型聚合物 ,易溶于多种有机极性溶剂 ,大大的扩…     

Poly(ethyleneimine) microcapsules: glutaraldehyde‐mediated assembly and the influence of molecular weight on their properties

Poly(ethyleneimine) (PEI) microcapsules were prepared via the method of glutaraldehyde (GA)‐mediated covalent layer‐by‐layer (LbL) assembly, which utilized GA to cross‐link the adsorbed PEI layer and to introduce free aldehyde group on the surface for the next PEI adsorption on MnCO₃ microparticles, followed by core removal. Evidenced by ellipsometry, the PEI multilayers grew nearly linearly along with the layer number and their thickness was controlled at the nanometer scale. The hollow structure, morphology, and wall thickness were characterized by scanning electron microscopy (SEM), scanning force microscopy (SFM), and confocal laser scanning microscopy (CLSM), revealing that the capsule structure as well as the cut‐off molecular weight of the capsule wall could be tuned by the molecular weight of PEI. This offers a general and novel pathway to fabricate single component capsules with pre‐designed structure (size, shape, and wall thickness) and properties. Copyright © 2007 John Wiley & Sons, Ltd.     

Blends of polycarbonate and ethylene-1-octylene copolymer

The mechanical properties and morphology of polycarbonate/ethylene-1-octylene copolymer (PC/POE) binary blends and PC/POE/ionomer ternary blends were investigated. The tensile strength and elongation at break of the PC/POE blends decreased with increasing the POE content. The impact strength of the PC/POE blends showed less dependence on thickness than that of PC. And the low-temperature impact strength of PC was modified effectively by addition of POE. The morphology of the PC/POE blends was observed by scanning electron microscope. The PC/POE weight ratio had a great effect on the morphology of the PC/POE blends. For the PC/POE (80/20)/ionomer ternary blends, low content (0.25 and 0.5 phr) of ionomer could increase the tensile properties of PC/POE (80/20) blend and had little effect on the impact strength. And 0.5 phr ionomer made the dispersed domain distribute more uniformly and finely than the blend without it. But with high content of ionomer, the degradation of PC made the mechanical properties of the blends deteriorate. Blending PC and ionomer proved the degradation of PC, and the molecular weight decreased with increasing the ionomer content.     

Unexpected molecular weight dependence of shish-kebab structure in the oriented linear low density polyethylene/high density polyethylene blends

In this study, highly oriented shish-kebab structure was achieved via imposing oscillatory shear on the melts of linear low density polyethylene (LLDPE)/high density polyethylene (HDPE) blends during the packing stage of injection molding. To investigate the effect of molecular weight of HDPE on the formation of shish-kebab structure, two kinds HDPE with large melt flow index (low molecular weight) and small melt flow index (high molecular weight) were added into LLDPE matrix. The structural characteristics of LLDPE/HDPE blends were systematically elucidated through two-dimensional wide-angle x-ray scattering, scanning electron microscopy, and differential scanning calorimetry. Interestingly, an unexpected molecular weight dependence of shish-kebab structure of the prepared samples was found that the addition of HDPE with low molecular weight resulted in an higher degree of orientation, better regularity of lamellar arrangement, thicker lamellar size, and higher crystal melting temperature than that adding HDPE with high molecular weight. Correspondingly, the blend containing low molecular weight HDPE had better tensile strength. A possible mechanism was suggested to elucidate the role of HDPE molecular weight on the formation of shish-kebab structure in the oriented blends, considering the change of chain mobility and entanglement density with change of molecular weight.     

聚醚聚氨酯-聚醚聚酰亚胺合金相结构的研究

通过不同分子量的对－氨基苯甲酸酯封端的聚（四次亚甲基）醚和均苯甲甲酸二酐反应,合成了聚醚聚酰胺酸;然后以不同重量比将聚醚聚氨酯和聚醚聚酰胺酸溶液混合反应亚胺化,制备了一系列不同硬段含量的聚醚聚氨酯－聚醚聚酰亚胺合金。用傅立叶变换红外光谱、动态力学分析、示差扫描量热、广角Ｘ－衍射、应力应变试验等分析测试方法对合金进行了研究,结果表明聚醚聚氨酯－聚醚聚酰亚胺合金具有很好的相分离结构,是一类新型耐高温、有韧性的热塑性弹性体。聚醚分子量相同的聚氨酯和聚酰亚胺形成的合金软段相容,合金具有两相结构;聚醚分子量不同的聚氨酯和聚酰亚胺形成的合金软段存在相分离,合金具有三相结构,表现在材料外观上分别为透明不透明的韧性膜,少量聚酰亚胺的掺入,能大大增加材料的耐热性能,而合金的材料力学性能没有明显变化。     

Properties of poly(<Emphasis Type="Italic">γ</Emphasis>-benzyl <Emphasis Type="SmallCaps">l</Emphasis>-glutamate) membrane modified by polyurethane containing carboxyl group

A series of poly(γ-benzyl l-glutamate) (PBLG)/polyurethane (PU) containing carboxyl group blend membranes was prepared by casting the polymer blend solution in dimethylformamide (DMF). The surface morphology of the PBLG/PU blend membranes was investigated by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Thermal, mechanical, and chemical properties of PBLG/PU blend membranes were studied by differential scanning calorimetry (DSC), tensile tests and other physical methods. It was revealed that the introduction of PU could exert outstanding effects on the morphology and the properties of PBLG membrane.     

多壁碳纳米管对环氧树脂/聚醚酰亚胺体系相分离的影响

通过溶液混合的方法制备了环氧树脂/聚醚酰亚胺(PEI)/多壁碳纳米管(MWCNTs)三元复合物,并使用扫描电镜(SEM)、原位红外分析(FTIR)、流变测试和非等温DSC等手段研究了MWCNTs的存在对体系相分离形貌和固化反应的影响.扫描电镜的结果显示,在固化后的样品中MWCNTs较均匀地分散在两相中.150℃下固化,不含MWCNTs和MWCNTs含量为0.75 pbw的体系相分离形貌呈海岛状结构,而进一步增大MWCNTs含量后相分离形貌呈双连续结构,且相区尺寸随MWCNTs含量的增加而减小.120℃下固化,不含MWCNTs和MWCNTs含量为0.75 pbw的体系相分离形貌呈双连续结构,而进一步增大MWCNTs含量后,体系相分离形貌呈相反转结构.FTIR和DSC的测试结果表明,MWCNTs表面的羟基对环氧树脂的固化反应起到催化作用,使得固化反应速度加快,反应活化能降低.而流变测试的结果表明,随着MWCNTs含量增加,一方面交叉跨越多个相区的碳纳米管使得体系黏度增大,对相分离起到了一定的抑制作用;另一方面使得体系凝胶化时间提前,导致体系相分离形貌被固定在相分离的较早阶段,起到有效调控相分离形貌的作用.     

聚酯／改性共聚酯共混体系的相分离及其共混纤维的结构和性能

本文研究聚酯(PET)和含3.5-二甲酸苯磺酸钠(SIPM)结构单元的改性共聚酯(PEI)的共混体系。差示扫描量热分析,X射线衍射分析,染色后的透射和扫描电镜照片等均表明该体系是一个热力学不相溶的体系。在加工成形过程中,特别是在结晶过程中,富PEI相中的SIPM结构单元被排斥在晶格之外形成集簇形态,利用这种相分离的结构形态以及改性共聚酯优先水解的机理,PET/PEI共混纤维经碱水解处理后可制得微孔型的高吸水吸湿纤维。本文讨论了相分离结构对该微孔型纤维的微孔尺寸分布,吸湿保水性能以及纤维力学性能的影响。     

Thermoplastic modification of monomeric and partially polymerized Bisphenol A dicyanate ester

Bisphenol A dicyanate ester (BADCy) was modified with different amounts of an engineering thermoplastic, polysulfone (PS) to improve impact strength of the parent resin. Differential scanning calorimetry of the blends suggested that addition of PS widens the curing exotherm of the BADCy considerably. FTIR of cured neat resins indicated total conversion of cyanate functional groups into triazine rings by cyclotrimerization. The cured neat resins showed phase separated morphology with cyanate ester as the continuous phase. The modified resins were shown to have better thermal, hygrothermal and impact strength properties. However, when glass fiber reinforced composites were made using partially polymerized BADCy and PS, very little or no phase separation in the resin was noticed. Flexural and impact strength measurement of composites showed that PS modification has compromised the flexural properties and only retained the impact strength of the parent resin containing composite. This study thus suggests that improvements realized in thermoplastic modification of monomeric BADCy are not directly transferable to composites using a partially prepolymerized BADCy.     

Properties of water-soluble carboxymethyl chitosan film modified by hydrophobic poly(propylene glycol)

A series of water-soluble carboxymethyl chitosan (CMCS)/poly(propylene glycol) (PPG) blend films with various CMCS/PPG mole ratios were prepared by the solution casting method. Morphology of the CMCS/PPG blend films was investigated by scanning electron microscopy (SEM). Thermal, mechanical, and chemical properties of the CMCS/PPG blend films were studied by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile tests, and contact angle tests. It was found that the introduction of PPG can markedly affect the morphology and the properties of CMCS films.     

Morphology and mechanical properties of ultra-high molecular weight polyethylene-poly(tetrafluoroethylene) blend films

This paper deals with the morphology and mechanical properties of blend films for polytetrafluoroethylene (PTFE) and ultra-high molecular weight polyethylene (UHMWPE) prepared by kneading techniques. This experiment was carried out for blend films, prepared with different compositions of PTFE and UHMWPE to improve thermal properties of PE. In spite of the incompatibility of the two polymers, the blend film with the PTFE/UHMWPE composition =75/25 was maintained under the measurement of complex modulus at temperature higher than 300°C. This indicates that the UHMWPE chains dispersed in PTFE fibrous texture were not separated by the melting flow of UHMWPE at 300°C. To check the origin of this interesting phenomenon, the morphology of the blend films was investigated by using scanning electron microscopy, X-ray diffraction, and¹³C nuclear magnetic resonance.     

Phase separation during synthesis of polyetherimide/epoxy semi-IPNs

The phase separation behavior and the morphology of polyetherimide (PEI)-modified diglycidyl ether of bisphenol A (DGEBA) epoxy resin were studied using scanning electron microscopy and light scattering. Reaction kinetics, cloud point and onset of gelation were determined by differential scanning calorimeter, optical microscope and physica rheometer, respectively. The mixture of partially cured epoxy and PEI showed bimodal upper critical solution temperature (UCST) behavior. For PEI content smaller than 10 wt%, the blends exhibited a sea-island morphology formed via nucleation and a growth mechanism. Above 25 wt% PEI content, the phase separation proceeded via a spinodal decomposition mechanism and a nodular structure was formed. With PEI content between 15 and 20 wt%, dual phase morphology was observed. This morphology was formed via primary spinodal decomposition and secondary phase separation within the dispersed phases and the matrix phases formed by the primary phase separation. This morphology was presumed to be formed in the reaction-induced phase separation mechanism with the mixture showing bimodal UCST behavior. The curing temperature had an effect on the final morphology, and the modulus of PEI-modified epoxy was influenced by the phase separation.     

Phase behavior and anisotropic optical properties of photoluminescent polarizers

The phase behavior and anisotropic optical properties of tensile deformed blends of a photoluminescent polymer guest in an ultra‐high molecular weight polyethylene matrix were studied on the level of single molecules by means of scanning confocal optical microscopy. It is shown that upon tensile deformation of the blends, the system transforms from a phase‐separated system into a quasi‐molecular solid solution. The influence of this phase transition on the anisotropic optical properties of oriented blend films was also investigated with polarized steady‐state photoluminescence spectroscopy. We show that well‐dissolved guest molecules tend to reach higher degrees of orientation at lower draw ratios of the blend films compared to guests that phase‐separate from the matrix polymer. Dichroic ratios in emission in the range of 50 were observed in optimized blend films based on photoluminescent oligomers and linear low density polyethylene.     

Surface modification of boron nitride by bio‐inspired polydopamine and different chain length polyethylenimine co‐depositing

We established a novel, easy, and versatile method of obtaining diverse and controllable interphases between epoxy resin and fillers. The method involved the co‐deposition of polydopamine (PDA) and polyethyleneimine (PEI) with different molecular lengths on boron nitride (BN) surface. The obtained PDA/PEI‐modified BN composites showed significantly improved mechanical properties, including tensile strength, toughness, and elongation at break. For example, the tensile strength, fracture toughness, and elongation at break of EP composite increased by 51%, 132%, and 170% compared with EP when the PEI molecular weight was 10 000, respectively. These results suggested that the interphases between BN and EP matrix can be adjusted by changing the molecular lengths of grafted modifiers, thereby offering a new method for the reasonable designing and exploitation of the BN‐based composite materials.     

聚左旋乳酸/聚氧化乙烯共混物的拉伸行为及结构转变

采用熔融共混方法制备了聚左旋乳酸(PLLA)和超高分子量聚氧化乙烯(PEO)共混物, 通过差示扫描量热(DSC)、 扫描电子显微镜(SEM)和二维广角X射线散射(2D-WAXS)等方法系统研究了PEO的加入对不同温度下PLLA拉伸行为及拉伸过程中微观结构变化的影响. 结果表明, PLLA/PEO共混物为非均相体系, PEO粒子均匀分布在PLLA中形成两相结构. PEO的加入能够显著降低PLLA的玻璃化转变温度(T_g), 在25～60 ℃范围内显著提高PLLA的拉伸性能. 在60 ℃拉伸时, PEO的加入提高了PLLA在拉伸过程中的结晶和形变能力. 在80 ℃拉伸时, 共混物的拉伸断裂伸长率下降, 但共混物的结晶速度仍高于纯PLLA样品.     

Effect of molecular weight on reaction-induced phase separation of epoxy resin modified with fluorocarbon chain terminated polyetherimide

Epoxy resins are currently used for many important applications such as adhesives, encapsulates and ad-vanced composite matrixes. However, the further use of epoxies is limited because of their inherent brittle-ness. Thus, the modifications of epoxy resin…     

Thermal and mechanical evaluation of cyanate ester resin modified with bismaleimide and diallyl phthalate

Cyanate ester resins have excellent dielectric, mechanical, and thermal properties; however, their major drawback is their brittleness. A high performance matrix blend was developed using bisphenol A dicyanate (BADCy), bismaleimide (BMI) and diallyl phthalate (DAP), and Cobalt (III) acetylacetonate dissolved in nonyl phenol (NP) as a complex catalyst system for BADCy. The properties of the BADCy/BMI/DAP blends, such as thermal and mechanical properties, were investigated in detail by dynamic mechanical analysis (DMA), thermogravimetric analysis (TGA), and mechanical measurement. The results show that the addition of the appropriate amount of DAP and BMI can improve the impact strength and the flexural strength and this possibly comes from forming an interpenetrating polymer network in the systems. However, the thermal stability of the blends was found to be lower than that of the unmodified BADCy resin. Copyright © 2009 John Wiley & Sons, Ltd.     

Miscibility of semirigid thermotropic liquid crystalline polycarbonate with poly(vinyl chloride)

Miscibility and morphology of polymer blends of semirigid thermotropic liquid crystalline (LC) polycarbonate (LCPC) with three commercial amorphous poly(vinyl chloride)s (PVC) having various molecular weights were investigated by means of differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). No phase separation was observed in the LCPC/PVC polymer blends. LCPC forms miscible polymer blends with the PVCs independent of molecular weight. The dynamic storage modulus of the LCPC/PVC polymer blends changes systematically with blend composition.