高温高压方法合成碳包覆γ-Fe_2O_3纳米棒及其磁学性能

采用高温高压(HPHT)方法,以水热法制备的聚乙烯醇包覆FeOOH纳米棒为前驱体,合成了碳包覆γ-Fe2O3纳米棒.通过使用多种表征方法,研究了HPHT过程中合成温度对样品结构和形貌的影响,并对样品的生长机理进行了探讨.利用振动样品磁强计测量了样品的室温磁学性质.实验结果表明,反应温度为400?C,压强为1 GPa条件下制备的碳包覆γ-Fe2O3纳米棒具有较高的长径比(直径约为20 nm,长度约为150 nm),矫顽力可达到330 Oe(1 Oe=79.5775 A/m).该方法为制备具有核壳结构的一维纳米材料提供了新思路.     

高温高压处理对褐色CVD钻石谱学特征的影响

目前CVD法合成单晶钻石是超硬材料科学和宝石学关注的热点之一,该方法合成的单晶钻石常带有褐色调。通常采用高温高压法（HPHT）提高褐色CVD钻石的色级和透明度,在前期HPHT处理褐色CVD钻石实验基础上,选出颜色改善明显的三颗样品,对其处理前后谱学特征进行对比。采用紫外-可见吸收光谱、红外光谱、光致发光光谱、三维荧光光谱、激光拉曼光谱以及X射线摇摆曲线进行分析。结果表明,褐色和深褐色样品褪色温度较高,处理后样品紫外-可见吸收光谱吸收系数明显减小,透明度明显提高。样品中红外与近红外光谱显示,在1 332 cm-1处的吸收峰与N+中心有关,该中心是褐色CVD钻石常见特征。在3 124 cm-1处吸收峰与NVH0缺陷中心有关,该峰在CVD钻石和HPHT处理钻石中常见。另外在2 700~3 200 cm-1范围变化的一组吸收峰,与C-H键伸缩振动有关。高温对CVD钻石含H基团影响较大,在5~6 GPa压力下处理温度在1 500~1 700 ℃范围,会在近红外波段4 673,6 352,7 354,7 540,7 804和8 535 cm-1出现一组吸收峰,可指示样品经过较高温度处理。目前针对CVD钻石以及经过HPHT处理的CVD钻石近红外波段的论述较少,该研究可以为鉴定CVD钻石及HPHT处理CVD钻石提供依据。综合光致发光光谱和三维荧光光谱分析,处理后样品NV-缺陷比例减小,SiV-中心缺陷比例增加。在5~6 GPa压力下,仅当处理温度高于1 500 ℃时,样品三维荧光光谱在λ_ex/λ_em=500 nm/575 nm处荧光峰增强,在λ_ex/λ_em=490 nm/550 nm处荧光峰消失,从某种意义上该峰位变化可指示样品经过较高温度处理。物相分析结果显示,HPHT处理后CVD钻石在1 332 cm-1处拉曼位移半高宽和XRD摇摆曲线半高宽均减小,表现出了较好的一致性,说明经HPHT处理的褐色CVD钻石结晶质量变优。     

Photothermal-chemical synthesis of P-S-H ternary hydride at high pressures

The recent discovery of room temperature superconductivity (283 K) in carbonaceous sulfur hydride (C-S-H) has attracted much interest in ternary hydrogen rich materials. In this report, ternary hydride P-S-H was synthesized through a photothermal-chemical reaction from elemental sulfur (S), phosphorus (P) and molecular hydrogen (H₂) at high pressures and room temperature. Raman spectroscopy under pressure shows that H₂S and PH₃ compounds are synthesized after laser heating at 0.9 GPa, and a ternary van der Waals compound P-S-H is synthesized with further compression to 4.6 GPa. The P-S-H compound is probably a mixed alloy of PH₃ and (H₂S)₂H₂ with a guest-host structure similar to the C-S-H system. The ternary hydride can persist up to 35.6 GPa at least and shows two phase transitions at approximately 23.6 GPa and 32.8 GPa, respectively.     

Structural stability of ultra-high temperature refractory material MoSi_2 and Mo_5Si_3 under high pressure

In-situ angle dispersive x-ray diffraction(ADXRD) with synchrotron radiation source is performed on an ultra-high temperature refractory of MoSi_2 and Mo_5Si_3 by using a diamond anvil cell(DAC) at room temperature. While the pressureinduced volume reduction is almost constant, the value of the bulk modulus increases with the decrease of molybdenum content in the system. According to the Brich–Murnaghan equation, the bulk modulus 222.1(2.1) GPa with its pressure derivative 4 of MoSi_2, and the bulk modulus 308.4(7.6) GPa with its pressure derivative 0.7(0.1) of Mo_5Si_3 are obtained.The experimental data show that MoSi_2 has distinct anisotropic behavior, Mo_5Si_3 is less anisotropic than MoSi_2. The result shows that MoSi_2 and Mo_5Si_3 have the structural stabilities under high pressure. When the pressure reaches up to 41.1 GPa, they can still maintain their body-cantered tetragonal structures.     

Ceramic synthesis of 0.08BiGaO_3–0.90BaTiO_3–0.02LiNbO_3 under high pressure and high temperature

In this paper, the preparation of 0.08BiGaO_3–0.90BaTiO_3–0.02LiNbO_3 is investigated at pressure 3.8 GPa and temperature 1100–1200?C. Experimental results indicate that not only is the sintered rate more effective, but also the sintered temperature is lower under high pressure and high temperature than those of under normal pressure. It is thought that the adscititious pressure plays the key role in this process, which is discussed in detail. The composition and the structure of the as-prepared samples are recorded by XRD patterns. The result shows that the phases of Ba TiO_3, BaBiO_(2.77), and Ba_2Bi_4Ti_5O_(18) with piezoelectric ceramic performance generate in the sintered samples. Furthermore, the surface morphology characteristics of the typical samples are also investigated using a scanning electron microscope. It indicates that the grain size and surface structure of the samples are closely related to the sintering temperature and sintering time. It is hoped that this study can provide a new train of thought for the preparation of lead-free piezoelectric ceramics with excellent performance.     

宝石翡翠的合成、热行为和热稳定性的研究

 按硬玉分子组成配料，在1 350~1 550 ℃的高温下灼烧，然后淬火到室温得到具有硬玉组成的玻璃；在5.0 GPa，1 450 ℃下晶化，合成了宝石翡翠，其尺寸可达到Φ12 mm×6 mm，并通过差热分析及高压下的淬火分析研究了翡翠在常压下及高压下的熔点变化。利用淬火、退火及老化试验研究了人工翡翠宝石的稳定性。结果表明，人工翡翠宝石的热稳定性与天然翡翠相同。     

High pressure study on the superconducting transition temperature and Hall coefficient of Ba1−xKxBiO3 up to 8 GPa

The superconducting transition temperature (T_c) of Ba_0.62K_0.38Bio₃ (T_c=30 K) has been measured under high pressure up to 8 GPa. It is observed that T_c increases initially with pressure, as reported by Uwe et al., Shirber et al. and Huang et al., but decreases above 4 GPa. The Hall coefficient of Ba_0.62K_0.38BiO₃ has been measured up to 1.2 GPa. The absolute value of the Hall coefficient decreases with pressure by 10% GPa, the value of which is almost the same as that obtained in most CuO-based high-temperature superconductors.     

Different effect of NiMnCo or FeNiCo on the growth of type-Ⅱa large diamonds with Ti/Cu as nitrogen getter

In order to synthesize high-quality type-Ⅱa large diamond, the selection of catalyst is very important, in addition to the nitrogen getter. In this paper, type-IIa large diamonds are grown under high pressure and high temperature(HPHT) by using the temperature gradient method(TGM), with adopting Ti/Cu as the nitrogen getter in Ni_(70)Mn_(25)Co_5(abbreviated as NiMnCo) or Fe_(55)Ni_(29)Co_(16)(abbreviated FeNiCo) catalyst. The values of nitrogen concentration(N_c) in both synthesized high-quality diamonds are less than 1 ppm, when Ti/Cu(1.6 wt%) is added in the FeNiCo or Ti/Cu(1.8 wt%) is added in the NiMnCo. The difference in solubility of nitrogen between both catalysts at HPHT is the basic reason for the different effect of Ti/Cu on eliminating nitrogen. The nitrogen-removal efficiency of Ti/Cu in the NiMnCo catalyst is less than in the FeNiCo catalyst. Additionally, a high-quality type-Ⅱa large diamond size of 5.0 mm is obtained by reducing the growth rate and keeping the nitrogen concentration of the diamond to be less than 1 ppm, when Ti/Cu(1.6 wt%) is added in the FeNiCo catalyst.     

Evolution of superconductivity and charge order in pressurized RbV3Sb5

The kagome metals AV₃Sb₅(A=K,Rb,Cs)under ambient pressure exhibit an unusual charge order,from which superconductivity emerges.In this work,by applying hydrostatic pressure using a liquid pressure medium and carrying out electrical resistance measurements for RbV₃Sb₅,we find that the charge order becomes suppressed under a modest pressure pc(1.4 GPa3Sb₅.Our findings point to qualitatively similar temperature-pressure phase diagrams in KV₃Sb₅ and RbV₃Sb₅,{and suggest a close link}between the second superconducting dome and the high-pressure resistance anomalies.     

High thermal stability of diamond-cBN-B_4C-Si composites

Improving the thermal stability of diamond and other superhard materials has great significance in various applications. Here, we report the synthesis and characterization of bulk diamond–cBN–B_4C–Si composites sintered at high pressure and high temperature(HPHT, 5.2 GPa, 1620–1680 K for 3–5 min). The results show that the diamond, cBN, B_4C,B_xSiC, SiO_2 and amorphous carbon or a little surplus Si are present in the sintered samples. The onset oxidation temperature of 1673 K in the as-synthesized sample is much higher than that of diamond, cBN, and B_4C. The high thermal stability is ascribed to the covalent bonds of B–C, C–N, and the solid-solution of B_xSiC formed during the sintering process. The results obtained in this work may be useful in preparing superhard materials with high thermal stability.     

高温高压下翡翠宝石的人工合成

 本文通过1 350～1 550 ℃高温灼烧得到了具有翡翠成份的玻璃，在压力2.0～4.5 GPa、温度900～1 450 ℃下完成了翡翠由非晶态到晶态的转变，合成出Φ8×3 mm的翡翠。通过适量的Cr、Cu、Co等离子掺杂染色，得到了翠绿色、朱红色和蓝色的翡翠。本文还研究了压力和温度对翡翠合成的影响。     

高压熔渗生长法制备金刚石聚晶中碳的转化机制研究

在6 GPa和1500 ℃的压力和温度范围内, 利用高压熔渗生长法制备了纯金刚石聚晶, 深入研究了高温高压下金刚石聚晶生长过程中碳的转化机制. 利用光学显微镜、X-射线衍射、场发射扫描电子显微镜检测, 发现在熔渗过程中金刚石层出现了石墨化现象, 在烧结过程中金刚石颗粒表面形貌发生了变化. 根据实验现象分析, 在制备过程中存在三种碳的转化机制: 1)金属熔渗阶段金刚石颗粒表面石墨化产生石墨; 2)产生的石墨在烧结阶段很快转变为填充空隙的金刚石碳; 3)金刚石直接溶解在金属溶液中, 以金刚石形式在颗粒间析出, 填充空隙. 本文研究碳的转化机制为在高温高压金属溶剂法合成金刚石的条件下(6 GPa和1500 ℃的压力和温度范围内)工业批量化制备无添加剂、无空隙的纯金刚石聚晶提供了重要的理论指导.     

Synthesis of ternary compound in H-S-Se system at high pressures

The chemical reaction products of elemental sulfur (S), selenium (Se), and molecular hydrogen (H₂) at high pressures and room temperature are probed by Raman spectroscopy. Two known compounds H₂S and H₂Se can be synthesized after laser heating at pressures lower than 1 GPa. Under further compression at room temperature, an H₂S-H₂Se and an H₂S-H₂Se-H₂ van der Waals compounds are synthesized at 4 GPa and 6 GPa, respectively. The later is of guest-host structure and can be identified as (H₂S)_x(H₂Se)_(2-x)H₂. It can be maintained up to 37 GPa at least, and the stability of its H₂Se molecules is extended:the H-Se stretching mode can be detected at least to 36 GPa but disappears at 22 GPa in (H₂Se)₂H₂. The pressure dependence of S-H and Se-H stretching modes of this ternary compound is in line with that of (H₂S)₂H₂ and (H₂Se)₂H₂, respectively. However, its hydrogen subsystem only shows the relevance to (H₂S)₂H₂, indicating that this ternary compound can be viewed as H₂Se-replaced partial H₂S of (H₂S)₂H₂.     

Elastic properties of CaCO_3 high pressure phases from first principles

Elastic properties of three high pressure polymorphs of CaCO_3 are investigated based on first principles calculations.The calculations are conducted at 0 GPa–40 GPa for aragonite, 40 GPa–65 GPa for post-aragonite, and 65 GPa–150 GPa for the P2_1/c-h-CaCO_3 structure, respectively. By fitting the third-order Birch–Murnaghan equation of state(EOS), the values of bulk modulus K_0 and pressure derivative K~'_0 are 66.09 GPa and 4.64 for aragonite, 81.93 GPa and 4.49 for post-aragonite, and 56.55 GPa and 5.40 for P2_1/c-h-CaCO_3, respectively, which are in good agreement with previous experimental and theoretical data. Elastic constants, wave velocities, and wave velocity anisotropies of the three highpressure CaCO_3 phases are obtained. Post-aragonite exhibits 25.90%–32.10% V_P anisotropy and 74.34%–104.30% V_S splitting anisotropy, and P2_1/c-h-CaCO_3 shows 22.30%–25.40% V_Panisotropy and 42.81%–48.00% V_S splitting anisotropy in the calculated pressure range. Compared with major minerals of the lower mantle, CaCO_3 high pressure polymorphs have low isotropic wave velocity and high wave velocity anisotropies. These results are important for understanding the deep carbon cycle and seismic wave velocity structure in the lower mantle.     

InSe的高压电输运性质研究

高压下对InSe样品进行原位电阻率和霍尔效应测量. 电阻率测量结果显示, 样品在5–6 GPa区间呈现金属特性, 在12 GPa 的压力下发生由斜六方体层状结构到立方岩盐矿的结构相变, 且具有金属特性. 霍尔效应测量结果显示, 样品在6.6 GPa由p型半导体转变成n型半导体, 电阻率随着压力的升高而逐渐下降是由于载流子浓度升高引起的. 关键词： InSe 高压 电阻率 霍尔效应     

B2O3添加宝石级金刚石单晶的生长特性

利用温度梯度法, 在5.3-5.7 GPa压力、1200-1600 ℃的温度条件下, 将B₂O₃粉添加到FeNiMnCo+C合成体系内, 进行B₂O₃添加宝石级金刚石单晶的合成. 研究得到了FeNiMnCo触媒生长B₂O₃添加宝石级金刚石单晶的相图分布规律. 结果表明B₂O₃添加会使晶体生长的“V”形区上移和低温六面体单晶生长区间变宽. 通过晶体生长实验, 研究合成了不同形貌的B₂O₃添加宝石级金刚石单晶. 研究同时证实, B₂O₃的过量添加会对宝石级金刚石单晶生长带来不利影响. 当B₂O₃的添加量高于约3 wt‰、生长时间超过20 h时, 很难实现优质B₂O₃添加宝石级金刚石单晶的生长. 但B₂O₃的适量添加(不超过1 wt‰), 有助于提高低温板状六面体宝石级金刚石单晶的成品率. 通过对晶体生长速度的研究发现, B₂O₃的添加使得优质晶体的生长速度明显降低, 随着晶体生长时间的延长, B₂O₃添加剂对晶体生长的抑制作用会越发明显. 扫描电镜测试结果表明, 合成体系内B₂O₃添加剂的引入, 导致晶体表面的平整度明显下降.     

Pressure dependence of the thermal stability in LiMn2O4

Structural stability in terms of the decomposition temperature in LiMn₂O₄ was systematically investigated by a series of high-temperature and high-pressure experiments.LiMn₂O₄ was found to have structural stability up to 5 GPa at room temperature.Under ambient pressure,the compound decomposed at 1300℃.The decomposition temperature decreased with increasing pressure,yielding more complex decomposed products.Below the decomposition temperature,the crystal structure of LiMn₂O₄ varied with pressure.The presented results in this study offer new insights into the thermal and pressure stability of LiMn₂O₄ materials as a cathode for lithium-ion batteries that can operate under extreme conditions.Therefore,these findings may serve as a useful guide for future work for improving lithium-ion batteries.     

High-pressure dynamic,thermodynamic properties,and hardness of CdP_2

Using a pseudopotential plane-waves method,we calculate the phonon dispersion curves,thermodynamic properties,and hardness values of α-CdP_2 and β-CdP_2 under high pressure.From the studies of the phonon property and enthalpy difference curves,we discuss a phase transform from β-CdP_2 to a-CdP_2 in a pressure range between 20 GPa and 25 GPa.Then,the thermodynamic properties,Debye temperatures,and heat capacities are investigated at high pressures.What is more,we employ a semiempirical method to evaluate the pressure effects on the hardness for these two crystals.The results show that the hardness values of both α-CdP_2 and β-CdP_2 increase as pressure is increased.The influence mechanism of the pressure effect on the hardness of CdP_2 is also briefly discussed.     

硫酸锂钾的高压相及室温以上的P-T状态图

本文用改进了的高压下差热分析方法以及金刚石压砧加温下的X射线衍射方法研究了硫酸锂钾(LiKSO₄)在室温以上的高压相变,较精确地测定了在3GPa、800℃以下各相的平衡条件,作出了它的P-T状态图。本文发现LiKSO₄在1.65GPa以上压力存在一个高压结构,标定了它的晶体参数,测量了它在高压下的热膨胀行为,并研究了高压相在常压时的热稳定性。 关键词：     

Na2CO3的高压拉曼光谱研究

碳酸盐是碳在地球内部的重要载体之一,其在地幔高温高压条件下的晶体化学是理解地球深部碳的赋存状态和循环过程的关键,而结构稳定性和相变是晶体化学最基本的研究内容。碳酸钠（Na₂CO₃）是一种常见的碱性碳酸盐矿物,在产自地幔过渡带-下地幔的金刚石中已发现含钠的碳酸盐矿物包裹体,这成为碳酸钠能够俯冲进入地幔深部的直接矿物学证据。前人利用拉曼光谱技术研究了Na₂CO₃在常温常压下的晶格振动模式,但其在高压下的稳定性和结构变化却鲜有报道。利用金刚石压腔装置结合先进的共聚焦拉曼光谱技术,以硅油作为传压介质,在准静水压力条件下,在0.001～27.53 GPa压力区间对Na₂CO₃粉末在600~1 200 cm-1波段的振动特征进行了细致地分析。本次实验重点分析了[CO₃]2-基团振动模式在升压和卸压过程中的行为。结果表明,在0.001～11.88 GPa压力范围内,[CO₃]2-基团对称伸缩振动γ₁（1 088.06和1 070.76 cm-1）、反对称伸缩振动γ₃（865.10和797.50 cm-1）和面内弯曲振动γ₄（720.10和696.71 cm-1）都出现了振动峰的分裂。随着压力增加,所有振动峰都向高频率漂移,半高宽也逐渐增加。在13.40 GPa时,Na₂CO₃发生结构相变,具体表现为690.08 cm-1处出现1条新的拉曼峰,并且随着压力升高该峰的强度逐渐增大。同时反对称伸缩振动峰γ₃以及面内弯曲振动峰γ₄的强度持续减弱,半高宽也继续变大。这些现象表明Na₂CO₃结构相变源于[CO₃]2-内部晶格变化。当压力卸载到4.18 GPa时,[CO₃]2-的振动模式与常温常压下的完全吻合,相变出现的新峰也已经消失,表明该相变是由[CO₃]2-基团畸变引起的并且具有可逆性。继续升压至27.53 GPa,拉曼光谱继续蓝移,Na₂CO₃的拉曼谱线再没有变化,说明高压相在这一压强范围内保持稳定。在整个加压过程中,反对称伸缩振动γ₃和面内弯曲振动γ₄处的拉曼峰出现强度减弱现象。同时也计算了各个峰频率对压力的依赖系数dγ/dP,结果显示[CO₃]2-基团内各个振动模式对压力的响应是不同的,这很可能与Ｃ-Ｏ键的键长有关。最后,对比发现,对称伸缩振动γ₁峰的强度比反对称伸缩振动γ₃和面内弯曲振动γ₄峰的强度大,并且[CO₃]2-基团对称伸缩振动γ₁受压力影响相对较小,可以用来区别不同种类的碳酸盐矿物。