纤维增强复合材料圆柱型界面裂纹分析

以裂纹面上的位错函数为未知量将圆柱型界面裂纹问题化成一组奇异积分方程的求解问题．应用Ｍｕｓｋｈｅｌｉｓｈｖｉｌｉ的奇异积分方程理论，分析了圆柱型界面裂纹尖端应力场．针对裂纹尖端分别存在和不存在接触区两种情况，确定了裂纹尖端应力场的奇异性．利用数值方法计算了圆柱型界面裂纹尖端接触区尺寸对剪应力强度因子的影响．     

两相材料界面裂纹的起裂方向及断裂参量研究

采用FRANC2D软件研究了两相材料含界面裂纹的断裂特性。通过在材料界面利用CASCA手动生成界面裂纹并在裂纹尖端附近设置1/4奇异等参元,得到了界面裂纹的复应力强度因子;数值模拟得到了界面裂纹的起裂方向,并分析了界面裂纹的破坏特征。计算结果表明:1/4奇异等参元很好地描述了裂纹尖端场的1/r(1/2)奇异性,FRANC2D软件能够模拟界面裂纹的扩展方向,可以得到界面裂纹尖端的应力场和复应力强度因子,为界面裂纹的断裂特性的进一步分析提供依据。     

周期界面裂纹反平面问题的动态应力强度因子

在研究动载荷作用下复合材料层板结构的安全与可靠性问题以及在抗震设计中关于地层裂缝的运动等问题中,都与界面裂纹有关。本文研究了分布于两个半空间之间的周期界面裂纹在反平面剪切波作用下裂纹尖端应力强度因子的动态特性。文中利用有限 Pourier变换,将在一个周期带内的边值问题转化成求解一个带周期性奇异核的积分方程,再借助于Chebyshev 多项式求得问题的级数解,最后分析了应力场在裂纹尖端的奇异性,得到了裂纹尖端动态应力强度因子的计算公式,并通过数值计算给出了应力强度因子随入射波频率变化的特性曲线。     

纤维端部的界面裂纹分析

基于弹性力学空间轴对称问题的通解,研究了短纤维增强复合材料中纤维端部的轴对称币形和柱形界面裂纹尖端的应力奇异性,得到了裂纹尖端附近的奇异应力场．研究结果表明,这两种轴对称界面裂纹尖端的应力奇异性相同,并且与平面应变状态下相应模型的应力奇异性一致,材料性能对裂纹尖端附近奇异应力场的影响可用三个组合参数描述     

垂直于界面V型缺口尖端的应力奇异性及其应用

基于双材料垂直于界面V型缺口理论,给出了单一材料和双材料裂纹问题、V型缺口问题应力强度因子的统一定义,得到了应力外推法计算双材料K_I的公式,数值算例验证了本文方法的有效性.以双材料单向拉伸和三点弯曲模型为对象,深入研究了双材料中弹性模量、泊松比、缺口深度、缺口张角对缺口尖端奇异应力场的影响,获得了一定范围内各种参数变化对缺口尖端奇异应力场的影响规律,为异体材料形成的V型缺口在应力断料中的应用提供了必要的参考依据.     

尖端具有吸附性接触的界面裂纹对瞬态弹性波作用下的动态响应

建立并研究一类接触型界面裂纹模型对瞬态弹性波作用下的动态响应问题。文中利用积分变换和积分方程法推导了确定这类问题的奇异积分方程组。采用围道积分技术和切比雪夫多项式展开技术，得到了待定系数的非线性代数方程组。最后给出了裂纹尖端接触区大小和接触应力随时间变化的数值结果，揭示了这种接触裂纹的动力学特性及物理上的合理性。     

可压缩粘弹性材料Ⅱ型动态扩展裂纹尖端场

为了研究粘性效应作用下的动态扩展裂纹尖端渐近场,建立了可压缩粘弹性材料II型动态扩展裂纹的力学模型,推导了可压缩材料Ⅱ型动态扩展裂纹的本构方程.在稳态蠕变阶段,弹性变形和粘性变形同时在裂纹尖端场中占主导地位,应力和应变具有相同的奇异量级r-1/(n-1).通过渐近分析求得了裂纹尖端应力、应变和位移分离变量形式的渐近解,并采用打靶法求得了裂纹尖端应力、应变和位移的数值结果,给出了应力、应变和位移随各种参数的变化曲线.数值计算表明,弹性变形部分的可压缩性对Ⅱ型裂尖应力场影响甚微,而对应变场和位移场影响较大.裂尖场主要受材料的蠕变指数n和马赫数M的控制.当泊松比ν =0.5时,可以退化为不可压缩粘弹性材料Ⅱ型动态扩展裂纹.     

双材料界面裂纹复应力强度因子的正则化边界元法

双材料界面裂纹渐近位移和应力场表现出剧烈的振荡特性, 许多用于表征经典平方根($r^{1/2})$和负平方根($r^{-1/2})$渐近物理场的传统数值方法失效, 给界面裂纹复应力强度因子($K_{1} +{i}K_{2} )$的精确求解增加了难度. 引入一种含有复振荡因子的新型"特殊裂尖单元", 可精确表征裂纹尖端渐近位移和应力场的振荡特性, 在避免裂尖区域高密度网格剖分的情况下, 可实现双材料界面裂纹复应力强度因子的精确求解. 此外, 结合边界元法中计算近奇异积分的正则化算法, 成功求解了大尺寸比(超薄)双材料界面裂纹的断裂力学参数. 数值算例表明, 所提算法稳定, 效率高, 在不增加计算量的前提下, 显著提高了裂尖近场力学参量和断裂力学参数的求解精度和数值稳定性.      

刚性-粘弹性材料界面Ⅰ型动态扩展裂纹的尖端场

裂纹尖端渐近场的研究是断裂力学研究的重要课题之一。为了研究粘性效应作用下的界面动态扩展裂纹尖端渐近场,建立了刚性.粘弹性材料界面Ⅰ型动态扩展裂纹的力学模型;在稳态蠕变阶段,弹性变形和粘性变形同时在裂纹尖端场中占主导地位,应力和应变具有相同的奇异量级,即(σ,ε)∝r-1/(n-1)。当n→∞,幂硬化粘弹性材料动态扩展裂纹尖端场与Freund给出的理想塑性材料动态扩展裂纹尖端场具有相近的奇异量级;结合运动和协调方程,推导出粘弹性材料动态扩展裂尖场的控制方程。根据问题的边界条件和连续条件,通过数值计算,得到了裂纹尖端连续的分离变量形式的应力、应变和位移场。数值计算表明,裂纹尖端场主要受材料的蠕变指数n和马赫数M的控制,这为解决工程实践中所遇到的相应的问题和建立材料的破坏准则提供理论的参考。     

三维界面裂纹的奇性应力场和应力强度因子分析

使用有限部积分概念和极限方法得到了三维平片界面裂纹的超奇异积分－微分方程组后,进一步利用二维超奇异积分主部分析方法,对裂纹前沿的应力场作了理论分析,并获得了其奇性应力场和裂纹面位移间断表示复位应力强度因子的精确表达式,为三维平片界面裂纹的超奇异积分－微分方程组的求解建立了数值方法,并分析了界面椭圆平片裂纹问题,和现有解比较,所得数值结果令人满意。     

The singularity behavior of an interface crack under a dynamic load

The singularity behavior of a crack on the interface of two different media under dynamic load is investigated. By introducing a small region in which the crack faces make frictionless contact and making use of a kind of integral equations with moving boundaries, it is proved that there are only square-root singularities near the interface crack tips in case that a dynamic load acts on it. Numerical results show that the normal stress in the contact region remains negative. The results of the stress intensity factor and the length of the crack face contact region are given to illustrate the dynamic behavior of the interface crack.This work is supported by the National Natural Science Foundation of China.     

Elastic-viscoplastic field at mixed-mode interface crack-tip under compression and shear

For a compression-shear mixed mode interface crack, it is difficult to solve the stress and strain fields considering the material viscosity, the crack-tip singularity, the frictional effect, and the mixed loading level. In this paper, a mechanical model of the dynamic propagation interface crack for the compression-shear mixed mode is proposed using an elastic-viscoplastic constitutive model. The governing equations of propagation crack interface at the crack-tip are given. The numerical analysis is performed for the interface crack of the compression-shear mixed mode by introducing a displacement function and some boundary conditions. The distributed regularities of stress field of the interface crack-tip are discussed with several special parameters. The final results show that the viscosity effect and the frictional contact effect on the crack surface and the mixed-load parameter are important factors in studying the mixed mode interface crack- tip fields. These fields are controlled by the viscosity coefficient, the Mach number, and the singularity exponent.     

Thermal stress intensity factors for an interface crack in a functionally graded layered structures

The fracture behavior of a functionally graded layered structure (FGLS) with an interface crack under thermal loading is investigated. Considering new boundary conditions, it is assumed that interface crack is partly insulated, and the temperature drop across the crack surfaces is the result of the thermal resistance due to the heat conduction through the crack region. The problem is formulated in terms of a system of singular integral equations. Numerical results are presented to show the influence of the material nonhomogeneity parameters and the dimensionless thermal resistance on the thermal stress intensity factors (TSIFs).     

弹性波与单侧界裂纹相互作用问题的边界元法

措助边界元法设计了一种迭代修正方法来求解单侧界面裂纹模型与弹性波的相互作用问题,作为对算法的检验,用这种方法我们具体地分析了平面简谐弹性波对一个则界面裂纹的入射,给出了裂纹面的接触形态及应力场。     

有限长界面裂纹对冲击载荷的响应

本文研究了受冲击载荷作用下界面裂纹的瞬态特性。通过引入裂纹尖端附近裂纹面无摩擦接触区,消除了界面裂纹问题中存在的振荡奇异性。由于产生了随时间变化的运动边界,应用积分变换及路径积分方法进行反演,在时间-空间域上给出了问题的控制积分方程。应用chebyshev多项式展开,将问题转化为非线性微分-积分方程组的求解。给出了剪切应力强度因子和裂纹面接触区尺寸的数值结果。所得结果表明,拉伸场中界面裂纹的扩展和剪切失效有密切关系。     

Dynamic behavior of two unequal parallel permeable interface cracks in a piezoelectric layer bonded to two half piezoelectric materials planes

IntroductionDuetotheintrinsicelectro_mechanicalcouplingbehavior,piezoelectricmaterialsareveryusefulinelectronicdevices.However,mostpiezoelectricmaterialsarebrittlesuchasceramicsandcrystals.Therefore ,piezoelectricmaterialshaveatendencytodevelopcriticalcracksduringthemanufacturingandthepolingprocesses.So ,itisimportanttostudytheelectro_elasticinteractionandfracturebehaviorsofpiezoelectricmaterials.Theincreasingattentiontothestudyofcrackproblemsinpiezoelectricmaterialshasledtoalotofsignificantw…     

移动接触下求解二维闭合裂纹的双重迭代边界元法

使用子域边界元法对受移动接触弹性体作用下的二维闭合裂纹问题进行了数值计算。由于两弹性体的接触界面和裂纹表面的接触范围的大小和接触状态事先是未知的 ,对此 ,在两个接触表面同时采用迭代的方法进行了求解。在裂纹的每个裂尖上都采用了四分之一的奇异单元以保证裂尖位移场和应力场奇异性的满足。用我们编制的二维裂纹问题程序对一些中心裂纹问题进行了计算 ,计算结果与经典断裂力学的理论值比较吻合。在无摩擦的条件下 ,对一些具有不同角度且受移动接触弹性体作用下的闭合裂纹问题进行了数值计算 ,得到了一些耦合作用下的应力强度因子的计算结果     

On a moving interface crack with a contact zone in a piezoelectric bimaterial

An inplane problem for a crack moving with constant subsonic speed along the interface of two piezoelectric materials is considered. A mechanically frictionless and electrically permeable contact zone is assumed at the right crack tip whilst for the open part of the crack both electrically permeable and electrically insulated conditions are considered. In the first case a moving concentrated loading is prescribed at the crack faces and in the second case an additional electrical charge at the crack faces is prescribed as well. The main attention is devoted to electrically permeable crack faces. Introducing a moving coordinate system at the leading crack tip the corresponding inhomogeneous combined Dirichlet–Riemann problem is formulated and solved exactly for this case. All electromechanical characteristics at the interface are presented in a closed form for arbitrary contact zone lengths, and further, the transcendental equation for the determination of the real contact zone length is derived. As a particular case of the obtained solution a semi-infinite crack with a contact zone is considered. The numerical analysis performed for a certain piezoelectric bimaterial showed an essential increase of the contact zone length and the associated stress intensity factor especially for the near-critical speed region. Similar investigations have been performed for an electrically insulated crack and the same behavior of the above mentioned parameters is observed.     

Energy release rate and contact zone in a cohesive and an interface crack by hypersingular integral equations

Solution of Cauchy-type singular integral equations permits the evaluation of the fracture parameters at the crack tips very accurately. However, it does not permit the determination of the crack opening and sliding displacements while ensuring no crack surface interpenetration unless the location of the contact zone is known a priori. In order to circumvent this shortcoming, this study presents a solution method based on the Hadamard-type singular integral equations to obtain the crack opening and sliding displacements directly while enforcing the appropriate conditions to prevent interpenetration. Furthermore, the crack opening displacements are physically more meaningful and readily validated against the finite element analysis predictions. The numerical solutions of the hypersingular integral equations provide not only crack opening and sliding displacements directly but also the stress intensity factors and energy release rates. Also, the behavior of the energy release rate is examined as the cohesive crack located parallel to the interface approaches the interface from either the soft or the stiff side of the interface. The limiting value of the energy release rate is established by considering an interface crack. As the cohesive crack approaches the interface from either side of the interface, the energy release rate approaches to that of the interface crack. However, the length of contact zone between the cohesive crack surfaces under uniform shear loading does not approach to that of the interface crack.     

A Peierls perspective on mechanisms of atomicfriction

Stick-slip behavior observed from nanoscale asperity friction experiments are often modeled by the one-degree-of-freedom Tomlinson model, which is unable to explain the effects of lattice structure and interface defects, or by molecular simulations which suffer temporal limitations in modeling the velocity- and temperature-dependent frictional behavior. A Peierls-type model developed in this work views the atomic frictional process as the initiation and gliding passage of dislocations with diffused cores on the interface. As a consequence of loss-of-ellipticity instability, the occurrence of stick-slip behavior relies on the interaction among interface slip field, contact stress fields, and existing defects. The friction stress for commensurate interface under large contact area can be approximated from the Rice model of screw-dislocation nucleation from a planar crack tip. The spatially inhomogeneous nature of rate-limiting processes and the coupling effects between contact size and interface incommensurability are successfully determined, which cannot otherwise be tackled in the Tomlinsonmodel.