High-power diode-bar end-pumped Nd:YLF laser at 1.053 microm

We describe efficient cw operation of a Nd:YLF laser end pumped by two beam-shaped 20-W diode bars on the 1.053-microm transition. Fundamental transverse-mode operation with output power of 11.1 W for ~29.5 W of incident pump power was demonstrated. In Q-switched operation 8.4 W of average power at a pulse repetition frequency of 40 kHz and ~2.6-mJ pulse energy at a pulse repetition frequency of 1 kHz were achieved.     

Q-switched operation of an in-band-pumped Ho:LuAG laser with kilohertz pulse repetition frequency

We report continuous-wave (CW) and repetitively Q-switched operation of an in-band-pumped Ho:LuAG laser at room temperature. End-pumped by a Tm:YLF solid-state laser with emission wavelength of 1.91 μm, the CW Ho:LuAG laser generated 5.4-W output at 2100.7 nm with beam quality factor of M ²～1.03 for an incident pump power of 14.1 W, corresponding to slope efficiency of 67% with respect to absorbed pump power. Up to 1.5-mJ energy per pulse at pulse repetition frequency (PRF) of 3 kHz and 4.5-W average power with FWHM pulse width of 28 ns at 5 kHz were demonstrated in repetitively Q-switched operation.     

High-power diode-pumped Yb3+:CaF2 femtosecond laser

We report what is believed to be the first demonstration of a high-power passively mode-locked diode-pumped femtosecond laser based on an Yb3+:CaF2 single crystal, directly pumped by a 15-W fiber-coupled laser diode. With a 5-at. % Yb3+ -doped sample and prisms for dispersion compensation we obtained pulses as short as 150 fs, with 880 mW of average power and up to 1.4-W average output power, with a pulse duration of 220 fs, centered at 1049 nm. The laser wavelength could be tuned from 1040 to 1053 nm in the femtosecond regime. Using chirped mirrors for dispersion compensation, the oscillator provided up to 1.74 W of average power, with a pulse duration of 230 fs, corresponding to a pulse energy of 20 nJ and a peak power of 85 kW.     

Efficient 1645-nm Er:YAG laser

We report a resonantly fiber-laser-pumped Er:YAG laser operating at the eye-safe wavelength of 1645 nm, exhibiting 43% optical efficiency and 54% incident slope efficiency and emitting 7-W average power when repetitively Q switched at 10 kHz. To our knowledge, this is the best performance (conversion efficiency and average power) obtained from a bulk solid-state Q-switched erbium laser. At a 1.1-kHz pulse repetition frequency the laser produces 3.4-mJ pulses with a corresponding peak power of 162 kW. Frequency doubling to produce 822.5-nm, 4.7-kW pulses at 10 kHz was performed to demonstrate the laser's utility.     

Directly diode-pumped millijoule subpicosecond Yb:glass regenerative amplifier

An Yb:glass regenerative amplifier directly side pumped by four 20-W diodes is demonstrated. By use of a novel pumping scheme and introduction of cylindrical optics into the cavity, a free-running average output power as great as 4 W with a TEM(00) -like mode was achieved from the bare cavity, with a 0.56 pump duty cycle. When the regenerative amplifier injected, 1-mJ 200-fs FWHM pulses were obtained following compression by use of 2-ms pump pulses and up to a 150-Hz repetition rate.     

Fiber based high repetition rate, high energy laser source applying chirped pulse amplification

We demonstrate the potential of a high-gain Yb-fiber amplifier system to provide ultrashort pulses with high energies. 100 μJ pulses generated at a repetition rate of 32 kHz exhibit nearly diffraction limited output (M²≈1.7) at a 1060 nm center wavelength. Using chirped pulse amplification, temporally streched laser pulses from a femtosecond oscillator could be compressed after amplification to subpicosecond pulse duration. The achievable intensities are high enough to create plasmas which can efficiently convert laser light to the extreme ultraviolet radiation. In a multimode Yb-doped fiber amplifier we obtained average powers of up to 22 W and single pulse energies up to 130 μJ.     

Fiber-coupled diode end-pumped Q-switched Tm,Ho:YLiF4 laser

At liquid-nitrogen temperature, at 10-kHz pulse repetition rate, Q-switched 36-ns pulses with average output power of 4 W at 2.05 μm and 4.5-W continuous wave output power with a total optical-optical conversion efficiency of 30%, were achieved from a 6% Tm, 0.5% Ho:YLiF4 laser. This laser was endpumped by a fiber-coupled laser diode emitting up to 15 W around 792 nm. The 1-m-long optical fiber carrying the pump radiation has a core diameter of 700 μm with a numerical aperture of 0.22.     

High-power tunable diode-pumped Yb3+:CaF2 laser

Results of diode-pumped cw laser operation of an Yb3+:CaF2 single crystal are reported for what is to our knowledge the first time. With a 5-at.% Yb3+ -doped sample we obtained 5.8-W output power at 1053 nm for 15 W of incident power at 980 nm. The laser wavelength could be tuned from 1018 to 1072 nm, and a small-signal gain as high as 1.8 was achieved, showing the great potential of Yb3+:CaF2 as an amplifier medium for femtosecond pulses.     

Femtosecond oscillator on Yb:KYW crystal pumped by laser diode with fiber output

A femtosecond laser based on an Yb:KYW crystal with direct longitudinal pumping by a high-power semiconductor injection laser with a fiber output is described. Femtosecond pulses were generated in the self-longitudinal-mode-locking operating condition due to the use of a semiconductor saturable absorber. The average power of the oscillator was as high as 3.5 W at a central wavelength of 1035 nm, the pulse length and pulse repetition rate being 200 fs and 85.5 MHz, respectively. The product of the pulse length and the radiation spectrum width was 1.3 times higher than the theoretical limit for the pulse shape described by the function sech². The designed master oscillator can be also used as a stand-alone source of femtosecond radiation pulses for material microprocessing and primary source for femtosecond laser amplification systems.     

16.2-W average power from a diode-pumped femtosecond Yb:YAG thin disk laser

We demonstrate a power-scalable concept for high-power all-solid-state femtosecond lasers, based on passive mode locking of Yb:YAG thin disk lasers with semiconductor saturable-absorber mirrors. We obtained 16.2 W of average output power in pulses with 730-fs duration, 0.47-muJ pulse energy, and 560-kW peak power. This is to our knowledge the highest average power reported for a laser oscillator in the subpicosecond regime. Single-pass frequency doubling through a 5-mm-long lithium triborate crystal (LBO) yields 8-W average output power of 515-nm radiation.     

Femtosecond 5-W Yb:KGW slab laser oscillator pumped by a single broad-area diode and its application as supercontinuum source

We demonstrate a novel and very simple design for an efficient high-power femtosecond Yb:KGW slab laser oscillator. The laser is capable of producing output powers of more than 5 W at 44-MHz repetition rate and pulse widths as short as 161 fs with a nearly diffraction limited beam and an optical-to-optical efficiency of more than 28%. The laser is pumped by a single broad-area laser diode and employs simple pump optics consisting of three lenses. The laser output power is distributed between two beams and single or combined outputs are discussed. In combination with a tapered fiber the laser was used to generate femtosecond supercontinua with up to 1.3-W average power and spectra spanning from 420 to over 1750 nm.     

Several hundred kHz repetition rate nanosecond pulses amplification in Er–Yb co-doped fiber amplifier

We have experimentally investigated several hundred kHz repetition rate 1,550-nm nanosecond pulses amplification in Er–Yb co-doped fiber amplifier (EYDFA). The experimental setup has three stage fiber amplifiers. At the output of the second stage EYDFA, Yb³⁺ ions induced amplified spontaneous emission (Yb-ASE) is not observed owing to the low pump power. In the third stage EYDFA, a simultaneously seeded 1,064-nm continuous-wave laser is used to control Yb-ASE. Without any additional 1,064-nm signal, significantly backward Yb-ASE which caused loss-induced heat accumulation at the input port of the pump combiner can be observed. The monitored temperature at the input port of the pump combiner rapidly grows from 30 to 80 °C when the pump power is turned from 20 to 32 W. When a 196-mW forward 1,064-nm laser is added, the monitored backward Yb-ASE power is significantly declined, and the monitored temperature is kept below 35 °C. But, the additional signal caused a large power fraction at 1,064 nm in the output laser. In our experiment at the maximum pump power of 48.5 W, the total output power is 20 W with ~6.4-W 1,550-nm pulsed laser and ~13-W 1,064-nm continuous-wave laser.     

High average power,all-solid-state external resonator Raman laser

As much as 3 W of average power at 1064 nm from a diode-pumped Nd:YAG laser, Q switched at 4 kHz, was used to pump an external-resonator, crystalline Ba(NO3)2 Raman laser generating a maximum of 1.3-W output at the first Stokes wavelength of 1197 nm. The slope efficiency was 63% with respect to the fundamental power incident on the Ba(NO3)2 crystal. A reduction in the beam quality of the Stokes output from M2 approximately 1.4 at lower Stokes powers to M2 approximately 3.4 at higher powers is attributed to thermal loading of the Raman-active crystal.     

Core area scaling of Nd:Al-doped silica depressed clad hollow optical fiber and Q-switched laser operation at 0.9 microm

We demonstrate a Q-switched, cladding-pumped, Nd:Al-doped silica depressed clad hollow optical fiber (DCHOF) laser, which generated up to 133 microJ of pulse energy at a repetition rate of 5 kHz and 0.9 W of average output power at a high repetition rate (>20 kHz) in a diffraction-limited beam (M(2)=1.08) at 927 nm. The laser was tunable from 919 to 935 nm. This result shows the potential of the DCHOF structure for the suppression of unwanted long-wavelength radiation in large-area cores suitable for high-power Q-switched laser operation.     

High-average-power kilohertz-repetition-rate sub-100-fs Ti:sapphire amplifier system

We report on a femtosecond Ti:sapphire laser amplifier system that generates pulse energies >5 mJ at a 1-kHz repetition rate. The system consists of regenerative and multipass amplifiers and uses the technique of chirped-pulse amplification. When the system was seeded with 70-fs pulses at 800 nm from a self-mode-locked Ti:sapphire oscillator, amplified pulses of 94-fs duration at a repetition rate of 1 kHz and an average output power of 5.4 W were produced. The amplified pulse-repetition rate is variable from 250 Hz to 3 kHz. Pulse energies of >7.5 mJ were obtained at 500 and 250 Hz.     

End-pumped, passively Q-switched Yb:YAG double-clad waveguide laser

We present a diode-pumped, double-clad Yb:YAG waveguide laser that contains an integrated section of a Cr(4+): YAG saturable absorber for passive Q switching. Using two 4-W polarization-coupled, broad-striped diode-pumped lasers, we obtained 30-microJ pulses of 1.6-ns duration at repetition rates of as much as 77 kHz. The slope efficiency was ~50% with respect to absorbed pump power, with a maximum output average power of 2.3 W and a peak power of ~18 kW . The output beam was single lobed, with M(2) values as great as 1.5x1.3 . We also demonstrate a passively Q -switched Nd:YAG waveguide laser of similar design, operating at 1.064 microm and 946 nm.     

High-gain Tm-doped fluoride fiber amplifier

A diode-pumped Tm-doped fiber-optic amplifier that has a small-signal gain of >30 dB at 1870 nm is reported. Output pulses of up to 3-W peak power at a 1-60-kHz repetition rate can be generated by amplification of 20-40-ns laser diode pulses of up to 2-mW launched peak power. The output signal quality, i.e., the ratio of the output pulse energy and the total amplified spontaneous emission (ASE) output energy between two pulses, depends on the relative propagation direction of pump and signal and can be dramatically increased by choice of the correct propagation scheme. In the optimum pump geometry the pulse energy can be raised to as much as 20 times the ASE energy. This is the first report to the author's knowledge of fiber-optic amplification of short diode laser pulses near 1.9 microm with high repetition rates in Tm-doped fibers.     

0.2-TW laser system at 1kHz

We have developed a 1-kHz repetition-rate Ti:sapphire laser system that can simultaneously generate high peak and average powers of 0.2TW and 4W, respectively. The laser system generates 4-mJ energy pulses with a 20-fs pulse width. We eliminated thermal lensing in the system by cooling the Ti:sapphire crystal to 125K. The output 20-fs pulses were fully characterized by use of the new technique of transient-grating frequency-resolved optical gating. We demonstrate experimentally that the pulse duration at the output is limited only by fifth-order dispersion.     

Efficient high-power diode-end-pumped TEM(00) Nd:YVO(4) laser with a planar cavity

We demonstrate a compact and efficient diode-end-pumped TEM>(00) laser with output power of 30 W for 48 W of incident pump power by use of two coated Nd:YVO> (4) crystals to form a thermally stabilized flat-flat cavity. In Q -switched operation 25 W of average power at a pulse-repetition rate of 100 kHz and ~0.9-mJ pulse energy at a pulse-repetition rate of 10 kHz were produced.     

Simultaneous all-solid-state multi-wavelength lasers --- a promising pump source for generating highly coherent terahertz waves

A diode-end-pumped Nd:YAG dual-wavelength laser operating at 1319 and 1338 nm is demonstrated. The maximum average output power of the quasi-continuous wave linearly polarized dual-wavelength laser is obtained to be 2.1 W at a repetition rate of 50 kHz with an output power instability of less than 0.38% and beam quality factor M² of 1.45. Using the two lines, the highly coherent and narrow linewidth terahertz radiation of 3.23 THz can be generated in an organic 4-N, N-dimethylamino--methyl-stilbazolium tosylate (DAST) crystal. Meanwhile, the multi-wavelength red laser at 659.5, 664 and 669 nm is generated by frequency doubling and sum frequency processes in a lithium triborate (LBO) crystal. The average red laser output power is enhanced up to 1.625 W at a repetition rate of 15 kHz with an output power instability of better than 0.53% and beam quality factor M² of 6.05. Using the three lines, it is possible to generate the multi-wavelength THz radiation of 3.3, 3.43 and 6.73 THz in an appropriate difference frequency crystal.