羟基自由基对多壁碳纳米管表面和结构的影响

碳纳米管纯化后，使用Fenton试剂产生羟基自由基对碳管进行改性处理，研究羟基自由基对碳管表面和结构的影响，并与碳管的混酸处理结果进行比较。FTIR结果表明：经Fenton试剂化学处理后，碳管表面主要引入羟基和羰基，而混酸能“剪切”碳管，产生大量羧基和羰基等官能团。根据Fenton试剂产生羟基自由基的机理，分析了Fenton试剂处理条件的影响因素，控制反应条件即过氧化氢与亚铁离子物质的量之比保持在10左右，而pH值则维持在3左右，对碳管进行改性处理。依据碳管Fenton试剂处理前后的FTIR谱图变化，初步探讨了羟基自由基与多壁碳纳米管作用的可能机理。机理分析表明，改性后碳管表面的羟基和羰基是羟基自由基对碳管上的不饱和键进行加成氧化的结果。     

CVD法制备单壁碳纳米管的纯化与表征

针对CVD法合成的单壁碳纳米管的特点提出了较为有效的纯化方法，并对纯化后碳管的存在形式进行了表征.结果表明,CVD法制备的单壁碳纳米管中所含的载体和催化剂绝大部分可以通过盐酸除去.在表面活性剂溶液中超声分散碳纳米管,可以使管与无定形碳及石墨状碎片进行有效的剥离.空气加热氧化法和稀硝酸回流法可有效地去除碳杂质,稀硝酸回流可以在纯化的同时对管的末端及侧壁进行功能化.     

液相氧化碳纳米管的氧化剂选择

研究了在不同氧化剂作用下,碳纳米管引入含氧官能团的情况,提出了利用Boehm滴定法对碳纳米管表面的羧基进行定量分析的方法。结合X-射线光电子能谱对含氧官能团的分析,进一步探讨了碳纳米管氧化的过程和机理。     

多壁碳纳米管的纯化及其表面含氧基团的表征

用兼具酸性和氧化性的HNO3水溶液可方便地除去残留在原生态多壁碳纳米管(CNT)上的Ni-MgO催化剂组分,同时在其表面产生某些含氧官能团,使原生态多壁碳纳米管的疏水性表面变为亲水性表面.采用Boehm中和滴定法以及X射线衍射(XRD)、热脱附谱(TPD)、傅里叶变换红外(FTIR)光谱和X射线光电子能谱(XPS)等技术对HNO3处理过的多壁碳纳米管的相组成和表面含氧官能团进行测量和表征.结果表明:所生成表面含氧官能团的总量以经7.0mol·L-1硝酸378K处理24h的CNT为最高;3种主要表面含氧官能团的含量高低顺序为,羧基内酯型羧基酚型羟基.     

恒电位氧化改性石墨毡及其氧还原电极的电化学性能

分别采用循环伏安改性法和恒电位氧化法对石墨毡进行改性处理,并采用循环伏安法对其电化学性能进行研究,实验结果表明,恒电位氧化改性较循环伏安改性的石墨毡有较好的氧还原活性。通过XRD、FTIR、接触角和CV针对恒电位氧化处理石墨毡进行了进一步的测试。测试结果显示,随恒电位氧化时间的增加,石墨毡表面亲水性含氧官能团增加,润湿性增强。恒电位氧化改性处理25 min的石墨毡氧还原峰电位及电流密度分别为~-0.43 V和~0.003 4 mA·cm^-2,显示出很好的电化学催化性能。基于以上结果,恒电位氧化法改性处理能够极大提高石墨毡的氧阴极活性。     

恒电位氧化改性石墨毡及其氧还原电极的电化学性能

分别采用循环伏安改性法和恒电位氧化法对石墨毡进行改性处理,并采用循环伏安法对其电化学性能进行研究,实验结果表明,恒电位氧化改性较循环伏安改性的石墨毡有较好的氧还原活性。通过XRD、FTIR、接触角和CV针对恒电位氧化处理石墨毡进行了进一步的测试。测试结果显示,随恒电位氧化时间的增加,石墨毡表面亲水性含氧官能团增加,润湿性增强。恒电位氧化改性处理25 min的石墨毡氧还原峰电位及电流密度分别为~-0.43 V和~0.003 4 mA·cm^-2,显示出很好的电化学催化性能。基于以上结果,恒电位氧化法改性处理能够极大提高石墨毡的氧阴极活性。     

Y型分支的碳纳米管的氧化铝模板法制备及其表征(英文)

利用两步氧化法,通过对氧化直流电压进行周期性调制可制备出带有Y型孔道的氧化铝模板;然后以金属钴为催化剂,乙炔为碳源,通过CVD法制取得到具有规则Y型分支的碳纳米管阵列.已制备出的碳管分支角度在20°～120°的范围内.实验表明,两段分支所成的角度以及分支的长度与合成氧化铝模板的脉冲电压调节规律有关,短脉冲,高氧化电压有利于生长出的短而密集的分支构型.     

石墨烯氧化程度对Ni(OH)_2赝电容性能的影响(英文)

基于密度泛函理论(DFT)设计了一系列不同氧化程度的还原氧化石墨烯片(rGNOs)并研究了其表面的氧化缺陷与吸附的氢氧化镍(Ni(OH)2)之间的相互作用.结果发现,rGNOs表面的含氧基团与Ni(OH)2之间的吸附能与含氧基团的氧化程度相关.在吸附Ni(OH)2后,rGNOs的原子间距和电荷分布的变化也都受rGNOs表面的含氧缺陷的氧化程度影响.理论计算的结果与实验观察的结果一致并能给出合理的解释.我们用简单的恒电位电化学沉积法有效地在rGNOs表面制备了粒径只有5 nm的Ni(OH)2纳米粒子.在Ni(OH)2/rGNOs制备过程中,氧化石墨烯的电化学还原是关键步骤.Ni(OH)2上吸附的Ni(OH)2因具有更高的吸附能而使其与在镍膜表面直接吸附的Ni(OH)2(在5 mV·s-1下比电容为656 F·g-1)相比具有更高的比电容值(在5 mV·s-1下为1591 F·g-1).rGNOs在吸附Ni(OH)2后构型和电荷分布的变化导致Ni(OH)2具有更低的等效串联电阻和更佳的频率响应.Ni(OH)2/rGNOs优异的赝电容特性表明其有潜力成为新型赝电容器材料.     

以吡啶为原料制备氮掺杂碳纳米管

在700～800 ℃,以吡啶为原料用CVD方法制备出了管径在20～40 nm的竹节状碳纳米管. EDX和XPS结果都表明氮掺杂到碳纳米管中. HRTEM研究发现掺氮碳纳米管的竹节由数层石墨片弯曲而成,纳米管外层石墨层逐渐消失.从Raman谱图的对照中发现,与相似条件下制备出的纯碳纳米管相比,氮掺杂碳纳米管的D谱带对G谱带的相对强度增加, TGA研究发现掺杂纳米管在较低温度下即被氧化,这些结果都说明氮掺杂使得纳米管的缺陷增加.     

恒电位氧化改性石墨毡及其氧还原电极的电化学性能（英文）

分别采用循环伏安改性法和恒电位氧化法对石墨毡进行改性处理,并采用循环伏安法对其电化学性能进行研究,实验结果表明,恒电位氧化改性较循环伏安改性的石墨毡有较好的氧还原活性。通过XRD、FTIR、接触角和CV针对恒电位氧化处理石墨毡进行了进一步的测试。测试结果显示,随恒电位氧化时间的增加,石墨毡表面亲水性含氧官能团增加,润湿性增强。恒电位氧化改性处理25 min的石墨毡氧还原峰电位及电流密度分别为~-0.43 V和~0.003 4 m A·cm~(-2),显示出很好的电化学催化性能。基于以上结果,恒电位氧化法改性处理能够极大提高石墨毡的氧阴极活性。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.