Analysis and compensation of thermal lens effects in Tm：YAP lasers

The thermal lens effects in Tm：YAP laser are analyzed by solving the Poisson equation with finite difference method. The thermal focal lengths measured are in the range of 40-90 mm at the pump power of 16-34 W, consistent with the simulation results. The temperature contribution coefficient （the linear coefficient between the maximum temperature in the laser crystal and the pump power） of 1.19 K/W is also obtained. The convex lens and plano-concave mirror thermal lens compensation methods are proposed and applied to a high power pumped Tm：YAP laser.     

Nonlinear mid-IR radiation in two-frequency semiconductor lasers with a corrugated waveguide

The nonlinear generation of a difference frequency mode in an injection quantum-well semiconductor laser is considered. A laser based on the InGaAs/GaAs/InGaP heterostructure is proposed, which generates two modes in the 1-μm range and the difference mode in a corrugated waveguide in the range from 10 to 20 μm. It is shown that the power of the difference mode produced by a laser with a 100-μm-wide waveguide in the mid-IR range at room temperature can be as high as a few microwatts if the power of the short-wave modes is 10 W.     

A diode-pumped linear intracavity frequency doubled Nd:YAG rod laser with 40 ns pulse width and 73 W green output power

We analyzed a linear cavity for intracavity frequency doubling of a diode-pumped acousto-optic Q-switched Nd:YAG rod laser, and showed that a green laser beam with a short pulse width can be generated efficiently. A green laser output power of 73 W corresponding to the 83.9% of maximum IR output power was obtained with a 40 ns pulse width at a 10 kHz repetition rate. A green output power of 40 W with a 35 ns pulse width was measured at a 5 kHz repetition rate. Minimum laser pulse width of approximately 32 ns was obtained around 1 kHz repetition rate for both green and IR laser beams.     

All-solid-state continuous-wave frequency-doubled Nd:YAG-BiBO laser with 2.8-W output power at 473 nm

We report on a diode-pumped Nd:YAG laser with 4.6 W of linear polarized continuous-wave (cw) output power on the 4F3/2 --> 4I9/2 transitions at 946 nm. Three different crystals, cut for critical type I phase matching at room temperature, are used for the intracavity frequency doubling of the laser: 10-mm-long LiBaO5 (LBO), an 8-mm-long beta-BaB2O4 (BBO), and a 10.4-mm-long BiB3O6 (BiBO) grown by FEE GmbH. Up to 2.8 W of cw output power in the blue spectral range at 473 nm has been achieved with the BiBO crystal (2.1 W with BBO and 1.5 W with LBO).     

百瓦级近衍射极限VCSEL泵浦激光器

报道了高功率、高光束质量的垂直腔面发射半导体激光器(VCSEL)侧泵的Nd:YAG激光振荡器。从VCSEL泵浦源的主动冷却的热沉结构出发,设计了5个227 W的VCSEL线阵,并且通过优化侧面泵浦大口径激光棒的结构,研制成了具备480 W输出能力的棒状激光模块,相应的光-光效率为49.7%。在此基础上,设计了一种高功率、高光束质量的VCSEL侧面泵浦棒状Nd:YAG激光振荡器。腔内插入望远镜光学元件,并通过优化各光学元件的参数使其工作在热近非稳区域,以达到增大基横模体积和抑制高阶横模目的。最终,获得114 W的输出功率,相应的平均光束质量因子M2为1.42。由于VCSEL具备优秀的波长-温度稳定性,这种高功率、高光束质量的VCSEL泵浦的固体激光器在工业、空间等领域,具有极为广阔的应用前景。     

D. CCD视频技术、等离子体诊断和脉冲辐射摄影

本文对CCD摄象技术、等离子体诊断和脉冲辐射摄影的国内外最新发展作了评述,并涉及到在高技术领域的应用。     

连续激光辐照ZnSe/MgF2/K9滤光片的透射特性研究

 分析了连续激光辐照ZnSe/MgF₂/K9滤光片引起透射特性的变化。在室温条件下，用波长0.632 8μm激光作为探测光束，测量了1.06μm连续激光辐照ZnSe/MgF₂/K9滤光片温升引起薄膜折射率的改变，导致探测光束通过干涉滤光片后透过率的热致非线性变化。在光斑直径0.75mm条件下，测量了不同功率激光辐照ZnSe/MgF₂/K9滤光片引起温升随时间的变化。在激光功率30W，辐照时间2.52s条件下，实验观测到ZnSe/MgF₂/K9滤光片薄膜破坏温度约为90℃，辐照时间10s时干涉滤光片形成的薄膜龟裂形貌。     

LBO Ⅰ类临界相位匹配内腔和频555 nm激光器

报道了全固态连续波555 nm激光器.555 nm激光是分别由Nd:YAG和Nd:YVO4晶体的946 nm和1342 nm谱线非线性和频产生,两条谱线在各自晶体对应能级跃迁分别为4F3/2-4Ⅰ9/2和4F3/2-4Ⅰ13/2.实验中采用复合折叠腔结构,利用LBOI类临界相位进行腔内和频,当注入Nd:YAG和Nd:YVO4晶体的泵浦功率分别为20 W和10 W时,获得1.06 W的TEM00连续波555 nm激光输出.4小时功率稳定度优于±3.3%.实验结果表明采用两种激光晶体进行腔内和频是获得激光的高效方法,并可以应用到其它两种激光晶体进行腔内非线性和频,获得更多不同波长激光输出.     

Application of a broadband blue laser diode to trace NO2 detection using off-beam quartz-enhanced photoacoustic spectroscopy

We applied for the first time, to our knowledge, broadband off-beam quartz-enhanced photoacoustic spectroscopy (BB-OB-QEPAS) to trace NO2 detection using a broadband blue laser diode centered at 450?nm. A detection limit of 18?ppbv (parts in 10(9) by volume) for NO2 in N2 at atmospheric pressure was achieved with an average laser power of 7?mW at a 1?s integration time, which corresponds to a 1?σ normalized noise equivalent absorption coefficient of 4.1×10(-9) cm(-1)?W=Hz(1=2). An Allan variance analysis was performed to investigate the long-term stability of the BB-OB-QEPAS-based NO2 sensor.     

高功率二极管激光器寿命测试

 介绍了高功率激光二极管不同模式的失效机理，分析了激光二极管不同的寿命测试方法；在冷却水温20℃和实际工作温度下分别对封装的激光器进行了寿命测试。根据试验结果得出退化率，推算出准连续二极管激光器在水温20℃，电流90A，占空比为10%（500Hz，200μs）时，平均激光工作寿命为2.19×10⁹次脉冲；冷却水温35℃时，其平均激光工作寿命下降为1.65×10⁹次脉冲。由实验结果分析得出，高功率激光器封装工艺中的焊料沉积和多层焊接技术，以及工作环境温度是影响激光器可靠性和寿命的关键因素。     

采用解析法对Nd:YAG单晶光纤的温度场研究

采用解析法对Nd:YAG单晶光纤激光器热效应相关的光纤温度场分布进行研究。建立了Nd:YAG单晶光纤热模型,在单晶光纤所满足的边界条件下通过解析求解热传导方程,得到在高功率808 nm泵浦光抽运下产生946 nm激光的单晶光纤温度场分布,并与传统Nd∶YAG激光晶体的温度场进行比较,然后分别与同泵浦条件下的有限元数值方法的分析结果进行研究对比,最后分析泵浦光参数、单晶光纤参数等对温度场的影响。结果表明,功率为86 W的泵浦光入射至单晶光纤端面的最高温升仅为30.98℃,明显优于同泵浦条件下传统Nd∶YAG晶体的端面温升结果94.37℃,与有限元数值法得到的Nd:YAG单晶光纤19℃温升结果相比,该解析法结果更接近于实验的测量值31℃,能够更精确描述晶体光纤温度场。本文可对单晶光纤激光器热效应的精确研究提供一定参考,进而有利于提高单晶光纤激光器的性能。     

金属靶和绝缘靶对飞秒激光吸收的比较

利用脉宽为150fs、强度为8×10¹⁵W/cm²的P偏振飞秒激光研究了与 金属靶和绝缘靶 相互作用过程中的激光能量吸收、超热电子产额及超热电子能谱. 实验发现，由于绝缘靶电 导率小，因此其电荷分离势大于金属靶，从而导致绝缘靶比金属靶具有较小的激光能量吸收 、较少的超热电子发射和较高的超热电子温度. 关键词： 金属靶 绝缘靶 激光吸收 超热电子     

Experimental Investigation of Thermal Lensing in End-pumped Nd:YVO4 Crystal Using a New Simple Approach

The stability of linear planar resonators involved in solid-state lasers is entirely decided by the thermal lens of the laser crystal. There exists a critical point between stable state and unstable state at which the thermally focusing point falls on the surface of one end mirror. Based on this fact, a new method for measuring the thermal focal length has been presented, and applied to three different Nd3+-doped (2%, 0.8%, and 0.5% ) Nd:YVO4 crystals at various absorbed pump power levels up to 10 W, the results show a good agreement with those of theoretical calculation. It also indicates that the thermal lensing is strongly dependent on the Nd3+-doped concentration, and is affected by crystal surface temperature, especially in the situation of weak thermal lensing.     

Validity of reciprocity rule on mouse skin thermal damage due to CO2 laser irradiation

CO₂ laser (10.6 μm) is a well-known infrared coherent light source as a tool in surgery. At this wavelength there is a high absorbance coefficient (860 cm^?1), because of vibration mode resonance of H₂O molecules. Therefore, the majority of the irradiation energy is absorbed in the tissue and the temperature of the tissue rises as a function of power density and laser exposure duration. In this work, the tissue damage caused by CO₂ laser (1–10 W, ～40–400 W cm^?2, 0.1–6 s) was measured using 30 mouse skin samples. Skin damage assessment was based on measurements of the depth of cut, mean diameter of the crater and the carbonized layer. The results show that tissue damage as assessed above parameters increased with laser fluence and saturated at 1000 J cm^?2. Moreover, the damage effect due to high power density at short duration was not equivalent to that with low power density at longer irradiation time even though the energy delivered was identical. These results indicate the lack of validity of reciprocity (Bunsen-Roscoe) rule for the thermal damage.     

散射光信号与石墨-二氧化硅激光辐照烧蚀阈值的关系

石墨-二氧化硅作为无机添加材料,广泛应用于各类航空航天器烧蚀涂层领域,其在高温下具有较高的反应吸热焓,在高能激光烧蚀领域具有良好的应用前景。目前,关于石墨-二氧化硅的高能激光烧蚀研究较少,尤其在高能激光烧蚀中的反应时间和烧蚀阈值难以确定。针对此问题,利用近红外探测器对激光辐照样品表面的散射光进行实时探测,并对其散射光曲线进行微分拟合处理。基于此散射光信号,结合样品烧蚀后的形态结构分析,研究了石墨-二氧化硅在不同激光功率密度下的反应时间阈值。研究结果表明:在激光输出功率密度为500 W/cm~2持续辐照10 s时,散射光拟合曲线持续升高无突变,表明未发生明显的烧蚀;当激光功率密度升高至1 000~1 500 W/cm~2时,散射光微分拟合曲线出现明显转折点,对应的反应时间阈值分别为1.5 s和0.8 s。     

A 658-W VCSEL-pumped rod laser module with 52.6% optical efficiency

A high-efficiency and high-power vertical-cavity surface-emitting laser (VCSEL) side-pumped rod Nd:YAG laser with temperature adaptability are demonstrated. The VCSEL side-pumped laser module is designed and optimized. Five VCSEL arrays are symmetrically located around the laser rod and a large size diffused reflection chamber is designed to ensure a uniform pump distribution. Furthermore, the absorbed pump power distribution of the rod is simulated to verify the uniformity of the pump absorption. Finally, a proof-of-principle experiment is performed in short linear cavity laser with single laser module. A continuous-wave output power of 658 W at 1064 nm is obtained, the corresponding optical-to-optical efficiency is 52.6%, and the power variations are ±0.7% over 400 s and ±3.1% over the temperature range from 16 ℃ to 26 ℃. To the best of our knowledge, this is the highest output power and the highest optical-to-optical efficiency ever reported for VCSEL pumped solid-state lasers. By inserting a telescopic module into the cavity and optimizing the TEM₀₀ mode volume, the average beam quality is measured to be M²=1.34 under an output power of 102 W. The experimental results reveal that such a high power rod laser module with temperature stability is appropriate or field applications.     

基于LD双端面泵浦的Nd:YAG高效率倍频激光器

报道了一种利用激光二极管（LD）双端面泵浦的Nd：YAG激光晶体,Cr⁴⁺：YAG晶体被动调Q,LBO临界相位匹配腔内倍频的高转换效率的绿光激光器。分析了双端面泵浦YAG激光器的热效应,实验中LD双端面泵浦,采用U型平行平面腔结构对Nd：YAG进行传导冷却。当总泵浦光为33.8 W时,得到被动调Q频率10 KHz、功率8.21 W的线偏振基频光输出。6.72 W的绿光输出的倍频效率为86%,输出光束为基模,M²为1.4。实验表明双端面泵浦YAG倍频激光器具有很高的转换效率。     

Highly efficient in-band pumped Er:YAG laser with 60 W of output at 1645 nm

A high-power Er:YAG laser that is in-band pumped by a high-power cladding-pumped erbium-ytterbium codoped fiber laser operating at 1532 nm is reported. The Er:YAG laser produced 60.3 W of continuous-wave output at 1645.3 nm in a beam with M2 approximately equal to 3 for 82 W of incident pump power and 20 W of TEM00 output with M2 < 1.2 for 32.4 W of incident pump power. The slope efficiency with respect to incident pump power at pump powers of >20 W was approximately 81%. In the Q-switched mode of operation, a slightly modified resonator configuration incorporating an electro-optic Q switch produced pulses of approximately 4 mJ energy and approximately 100 ns (FWHM) duration, corresponding to a peak power of approximately 42 kW at a repetition rate of 1 kHz for an incident pump power of 16.8 W. The prospects for further improvement in continuous-wave and Q-switched performance are discussed.     

Ideal laser-beam propagation through high-temperature ignition Hohlraum plasmas

We demonstrate that a blue (3omega, 351 nm) laser beam with an intensity of 2 x 10(15) W cm(-2) propagates nearly within the original beam cone through a millimeter scale, T(e)=3.5 keV high density (n(e)=5 x 10(20) cm(-3)) plasma. The beam produced less than 1% total backscatter at these high temperatures and densities; the resulting transmission is greater than 90%. Scaling of the electron temperature in the plasma shows that the plasma becomes transparent for uniform electron temperatures above 3 keV. These results are consistent with linear theory thresholds for both filamentation and backscatter instabilities inferred from detailed hydrodynamic simulations. This provides a strong justification for current inertial confinement fusion designs to remain below these thresholds.     

High-efficiency multi-kilowatt Er3+:YAG solid-state heat-capacity laser

First results on a diode-pumped multikilowatt-class Er(3+):YAG solid-state heat-capacity laser (SSHCL) are reported. The laser achieves an output power of 4650 W and output energies in excess of 440 J. A moderate crystal temperature increase due to crystal heating of 56.7 K/s is measured at 11.3 kW of pump power and the temperature-related power drop is determined to 8.8 W/K. The presented work is believed to be the first multi-kilowatt-class resonantly diode-pumped Er(3+):YAG laser.