Ni/Fe物质的量的比对Ni-Fe催化剂表面性质和二硝基甲苯加氢活性的影响

采用Fe粉置换氯化镍溶液中的Ni²⁺制备了Ni-Fe催化剂, 并应用于催化二硝基甲苯加氢合成甲苯二胺的反应中。运用XRD、低温氮吸附-脱附、H₂-TPD、XPS和TEM等技术手段对不同Ni/Fe物质的量的比(n_Ni/n_Fe)下催化剂进行了表征。结果表明, n_Ni/n_Fe对Ni-Fe催化剂表面性质影响显著。当n_Ni/n_Fe为1:4时, Fe抑制Ni氧化的作用达到最大, Ni-Fe催化剂化学氢吸附量和活性物种Ni的分散度分别达到了0.16 mmol·g^-1和23%, 催化剂性能得到较大的提升。在优化的催化剂制备条件下, DNT(二硝基甲苯)的转化率和TDA(甲苯二胺)的选择性分别达到了~100%和99%。另外, 对Ni-Zn漆原镍(Urushibara Ni)催化剂和Ni-Fe催化剂催化DNT加氢反应进程进行了研究, 发现它们有相同的加氢中间产物, 但反应不同阶段的催化速率存在差异。     

Ni/Fe物质的量的比对Ni-Fe催化剂表面性质和二硝基甲苯加氢活性的影响

采用Fe粉置换氯化镍溶液中的Ni²⁺制备了Ni-Fe催化剂,并应用于催化二硝基甲苯加氢合成甲苯二胺的反应中。运用XRD、低温氮吸附-脱附、H₂-TPD、XPS和TEM等技术手段对不同Ni/Fe物质的量的比(n_Ni/n_Fe)下催化剂进行了表征。结果表明,n_Ni/n_Fe对Ni-Fe催化剂表面性质影响显著。当n_Ni/n_Fe为1:4时,Fe抑制Ni氧化的作用达到最大,Ni-Fe催化剂化学氢吸附量和活性物种Ni的分散度分别达到了0.16 mmol·g^-1和23%,催化剂性能得到较大的提升。在优化的催化剂制备条件下,DNT(二硝基甲苯)的转化率和TDA(甲苯二胺)的选择性分别达到了~100%和99%。另外,对Ni-Zn漆原镍(Urushibara Ni)催化剂和Ni-Fe催化剂催化DNT加氢反应进程进行了研究,发现它们有相同的加氢中间产物,但反应不同阶段的催化速率存在差异。     

助剂对Ni/SiO_2催化剂微观结构及二硝基甲苯催化加氢性能的影响

采用等体积浸渍法制备了负载型Ni/SiO2催化剂,研究了Ce、Zr、La、Co和Fe助剂对催化剂微观结构及其催化二硝基甲苯(DNT,C6H3CH3(NO2)2)加氢制备甲苯二胺(TDA,C6H3CH3(NH2)2)性能的影响。通过XRD,BET,H2-TPD、H2-TPR和XPS技术对催化剂进行了表征。结果表明,助剂的引入促进了Ni物种在载体表面的分散,减小了Ni晶粒的尺寸,使得NiO晶粒更易还原。添加La、Fe和Zr助剂增加了有效的Ni活性中心数,有利于催化活性的提高,其中,添加La助剂制备的催化剂催化性能最优,DNT转化率和TDA选择性分别为98.1%和99.1%。但Co和Ce助剂的加入降低了化学氢吸附量,使得有效的Ni活性中心数降低,降低了催化剂的催化活性。     

助剂对Ni/SiO2催化剂微观结构及二硝基甲苯催化加氢性能的影响

采用等体积浸渍法制备了负载型Ni/SiO₂催化剂,研究了Ce、Zr、La、Co和Fe助剂对催化剂微观结构及其催化二硝基甲苯（DNT,C₆H₃CH₃（NO₂）₂）加氢制备甲苯二胺（TDA,C₆H₃CH₃（NH₂）₂）性能的影响。通过XRD,BET,H₂-TPD、H₂-TPR和XPS技术对催化剂进行了表征。结果表明,助剂的引入促进了Ni物种在载体表面的分散,减小了Ni晶粒的尺寸,使得NiO晶粒更易还原。添加La、Fe和Zr助剂增加了有效的Ni活性中心数,有利于催化活性的提高,其中,添加La助剂制备的催化剂催化性能最优,DNT转化率和TDA选择性分别为98.1%和99.1%。但Co和Ce助剂的加入降低了化学氢吸附量,使得有效的Ni活性中心数降低,降低了催化剂的催化活性。     

Mo含量对Ni-Mo-B非晶态合金催化剂结构及催化二硝基甲苯加氢性能的影响

采用化学还原法制备Ni-Mo-B非晶态合金催化剂, 研究了Mo含量对二硝基甲苯加氢制备甲苯二胺催化性能的影响. 结果表明, 当Mo含量(摩尔分数)≤6%时, Mo助剂使Ni-B非晶态合金催化剂的催化活性显著提高, 选择性均达到100%. 通过XRD, TEM, DSC, XPS, ICP和H₂-TPD技术对催化剂微观结构进行了表征, 结果表明, 随着Mo助剂含量的增加, Ni-Mo-B非晶态合金催化剂中不仅非晶态结构的无序程度增大, 催化剂粒径逐渐由60 nm左右减小至15 nm左右, 而且分布更加均匀, Ni吸附中心的H₂吸附强度变弱, 使氢物种更易于在催化剂表面流动并参与反应, 同时Mo助剂还显著提高了催化剂的热稳定性和抗氧化性. 当Mo含量为6%时, Ni-Mo-B非晶态合金催化剂的催化性能最好, 在2 MPa和110℃反应条件下, 二硝基甲苯转化率达99.8%, 甲苯二胺选择性为100%.     

二硝基甲苯低压加氢Ni-La-B非晶态合金催化剂的制备及结构表征

用化学还原法制备了Ni-La-B非晶态合金催化剂,并采用X射线衍射、透射电镜、差热分析、X射线光电子能谱、电感耦合等离子光谱和H2程序升温脱附技术对催化剂进行了表征,研究了La含量对催化剂微观结构及其催化二硝基甲苯(DNT)加氢制二氨基甲苯(DAT)性能的影响.结果表明,随着助剂La含量的增加,Ni-La-B催化剂中非晶态结构的长程无序程度增大,催化剂平均粒径逐渐由70nm左右减小至10nm左右,分布更加均匀;同时降低了Ni吸附H2的强度,使H2吸附物种更易于在催化剂表面流动并参与反应.另外,La助剂还显著提高了催化剂的热稳定性和抗氧化性.在二硝基甲苯加氢反应中,催化剂性能随着La加入量提高至6%(摩尔分数)时,1MPa低压条件下DNT转化率和DAT选择性均达100%.当La加入量为8%时,催化剂的Ni活性中心数明显减少,其活性下降.     

制备方法对Ni/ZnO催化丙三醇重整-氢解性能的影响

采用浸渍法、共沉淀法、水热法和碳微球硬模板法制备了Ni/ZnO催化剂,运用X射线衍射、程序升温还原、透射电子显微镜和氢滴定等手段对其进行了表征,并用于连续固定床反应器中无外加氢气条件下的丙三醇重整-氢解反应.结果表明,在较低空速下,生成的1,2-丙二醇(1,2-PDO)易在Ni分散度较高的催化剂上进一步裂解为乙醇和气相产物;而在较高空速下,其选择性受制于中间产物丙酮醇的加氢.在优化的空速下,Ni分散度越高越有利于1,2-PDO的生成.在Ni分散度最高的Ni/ZnO催化剂上,当丙三醇质量空速为0.84h-1时,1,2-PDO选择性最高,为54.9%,丙三醇转化率为85.4%.     

Ni-Fe/La2O2CO3催化乙醇水蒸气重整制氢的研究

采用La2(CO3)3空气焙烧法制备了La2O2CO3载体、采用浸渍法制备了Ni,Fe不同比例的Ni-Fe双金属催化剂及Ni/La2O2CO3,Fe/La2 O2 CO3催化剂,考察了各催化剂从300～700℃催化乙醇水蒸气重整反应的性能,并用BET,XRD,TPR等技术对催化剂进行表征。结果表明,相对单一金属催化剂,Ni-Fe双金属催化剂均表现出更高的活性,这可能是因为高分散的Ni,Fe和LaFeyNi1-yO3的共存作用。其中Ni含量为10%,Fe含量为5%时的Ni-Fe/La2O2CO3表现出最高的活性,400℃时乙醇的转化率为100%,H2的选择性最高达到94.1%,而CO的选择性则低至1.2%。     

Ni-Fe/蒙脱土催化剂催化乙醇水蒸气重整制氢的研究

采用浸渍法制备了一系列Ni-Fe/蒙脱土(MMT)催化剂,并应用于乙醇水蒸气重整制氢反应(ESR)。采用X射线衍射(XRD)、N_2吸附脱附分析和H_2-程序升温还原(H_2-TPR)表征手段对催化剂的物理化学性质、还原性能、碳沉积等进行了研究。结果表明,Ni-Fe/MMT催化剂中,Ni、Fe高度分散在载体MMT层间及表面,而且Fe的加入降低了Ni颗粒的粒径,增强了Ni~(2+)与载体的相互作用力。以10Ni5Fe/MMT为催化剂,在反应温度为500℃、水醇比为3∶1、空速为12 h~(-1),反应进行30 h后,乙醇转化率为100%,氢气选择性仍保持72%,副产物CO和CH_4含量明显降低。这是因为催化助剂Fe的引入,一方面,提高了Ni的分散度,使得ESR低温活性较好;另一方面,减小了Ni颗粒粒径,小颗粒的Ni有利于抑制甲烷的生成,并且Fe的加入加强了甲烷重整和水煤气变换反应,提高产物中氢气的选择性。     

微波辅助Ni-B/SiO2非晶态催化剂的制备及其在硝基苯加氢中催化性能的研究

采用微波辐射干燥浸渍法获得的Ni2 /SiO2,再由液相KBH4还原制备Ni-B/SiO2非晶态催化剂,在液相硝基苯加氢反应中,该催化剂对苯胺的选择性为100%,催化活性显著高于由传统加热法制备的Ni-B/SiO2.根据XRD、XPS、SEM和氢吸附等表征,两种催化剂具有相似的活性中心本质,催化性能的不同主要归因于分散度的区别.与传统加热法相比,微波加热具有受热均匀以及增强Ni2 与载体SiO2相互结合力的特点,导致Ni-B/SiO2(MW)分散度增加,并能减少催化反应过程中活性相的脱落流失,延长催化剂使用寿命.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.