水溶性甲壳素及其膜的制备与表征

通过对高脱乙酰度壳聚糖进行均相乙酰化反应，制得脱乙酰度为51．7％的水溶性甲壳素，产物有很好的水溶性．通过红外光谱、X-射线衍射、差热分析等测试表征了水溶性甲壳素结构．结果表明，水溶性甲壳素的结构发生了较大变化，结晶性显著下降是导致水溶性增加的主要原因．     

含偶氮苯聚芳亚胺的合成、表征和光谱分析

以4,4＇-二溴二苯甲酮和4,4＇-二氨基偶氮苯为单体,通过钯催化的胺基化反应缩聚合成了含偶氮苯基团的新型结构聚芳亚胺（PAI-A）．PAI-A结构通过FT—IR,^1H NMR和元素分析测定,测试结果和目标产物吻合良好．在不同的条件下测定了聚合物的光学性能．     

ZnS微米花的水热合成及光催化性质研究

本文采用简便的水热法一步合成ZnS微米花,通过X射线衍射仪、扫描电子显微镜等表征手段研究了合成产物的形貌及微观结构,并考察了合成产物的光催化性质。合成产物的光催化测试结果表明,在紫外光辐照下,产物对亚甲基蓝、甲基橙和曙红都有很好的降解效果。为了测试产物循环利用的光催化能力,对其进行了5次降解实验,结果显示产物依然保持良好的光催化活性。     

均匀沉淀法制备一维结构的氧化锌

以硝酸锌和尿素为反应原料,利用均匀沉淀法在水溶液中直接制备了多种形貌的氧化锌．考察了反应物浓度,加热方式等对产物形貌和结构的影响,利用透射电子显微镜,X射线衍射仪等分析手段对所得产物的形貌和结构进行了表征．     

1，4-环己烷二甲醇改性生物可降解聚酯PBS的合成与性能表征

用熔融缩聚法合成了一系列聚（丁二酸丁二醇酯丁二酸-1,4-环己烷二甲醇酯）无规共聚物。通过。H—NMR、FT—IR、DSC、TGA、XRD、酶降解测试等方法表征了材料的结构与性能。结果表明：合成得到的共聚酯为预期产物;共聚酯的晶体结构发生了改变,并产生了共晶行为;随着1,4-环己烷二甲醇（CHDM）含量的增加,产物的熔点由113．7℃降至64．6℃,然后升至114．2℃,玻璃化转变温度由-33．8℃单调升高至5．4℃;CHDM的引入增强了共聚酯的热稳定性;酶降解测试得出产物P51、P31具有良好的生物降解性,且P51降解最快。     

Sb2O3／TiO2纳米复合物的合成及性质研究

以改进的溶胶-凝胶法制备了Sb2O3／TiO2纳米复合物,用扫描电镜、X射线粉末衍射、傅立叶红外光谱、紫外-可见光谱以及荧光等测试技术对产物进行了分析和表征．结果表明：所得纳米复合物颗粒分散均匀,具有锐钛矿相结构,平均粒径约为10nm．还研究了所得产物的光催化性质、电化学性质及电化学发光行为．结果表明：Sb2O3的掺入可以提高TiO2的光催化效果,当反应物中m（Sb2O3）／m（TiO2）=10％时,所得纳米复合物对亚甲基蓝和罗丹明B的光催化效果最好．     

磁场对天然植物粉与硅酸聚合的影响

本文对天然植物粉与硅酸聚合产物的磁场影响进行了研究 ,通过红外光谱和不同时间的粘度系数测试结果表明 :磁场的作用有利于提高聚合的速度和聚合产物的分子量 ,聚合物的结构也有一定的差异。     

硫酸亚铁铵实验不同结晶条件的探讨

硫酸亚铁铵的制备是大学基础化学实验的一个经典实验,结晶条件对目标产物的结构和形态影响较大,研究了在不同结晶条件下制备了硫酸亚铁铵,并对其进行了单晶结构测试和解析,探讨了硫酸亚铁铵的最佳结晶条件。     

反应温度对衣康酸掺杂聚苯胺性能的影响

以衣康酸为掺杂剂,过硫酸铵为引发剂,采用化学氧化聚合法在不同的反应温度下合成聚苯胺(PANI)。计算其产率和电导率,并测定掺杂态聚苯胺的各项性能指标。通过电阻测试、傅立叶红外光谱测试(FT-IR)、紫外-可见光谱测试(UV-vis)、电子探针分别对产物的导电性、化学结构、紫外可见光谱和微观形貌进行了表征。结果表明,低温有利于减缓链终止的速度使得产物分子链较长,从而使载流子的传输更容易进行,产物电导率高;而温度高于10℃会使聚苯胺氧化断链,使产物电导率下降。以反应温度为10℃时电导率最高,为1.29×10-2(S·cm-1),且具有最高的产率为111.2%,微观形貌为纳米棒状结构。     

LiCoO_2掺杂对锰酸锂结构和性能的影响

用固相反应合成了LiCoO2掺杂改性的LiMn2O4锂离子电池正极材料,优化了LiMn2O4的改性路径及制备条件.利用SEM、XRD对产物的结构进行了表征,并测试了产物的电化学性能.结果表明:所得产物均具有尖晶石型LiMn2O4结构.LiCoO2的掺入增加了尖晶石结构的稳定性,改善了尖晶石型LiMn2O4的充放电循环性能.     

Understanding the "tailoring synthesis" of CdS nanorods by O2

Parameters such as solution concentrations and composition of the ambient atmosphere are known to be important in phase and morphology control in the solvothermal synthesis of CdS semiconductor nanorods (NRs), but a clear understanding of the underlying mechanisms involved is lacking. In this work, a series of experiments were performed to demonstrate that the key factor affecting the phase and morphology of CdS NRs is the amount of O(2) in the space above the reaction solution in the sealed vessel relative to the amount of precursors in solution: O(2)-depleted conditions resulted in more cubic phase CdS and thick polycrystalline NRs with an aspect ratio usually less than 3, which have small blue shifts in band-edge emission and little surface trap emission, while O(2)-rich conditions resulted in more hexagonal-phase CdS and slim single-crystal NRs, which have significantly blue shifted band-edge emission and relatively strong surface trap emission. Thus, increasing the amount of solution in the vessel, changing the ambient atmosphere from air to N(2), and increasing the reagent concentration all lower the molar ratio of O(2) to reagents and lead to more cubic phase and thicker NRs. The results indicate that the composition of the "empty" section of the reaction vessel plays as important a role as the composition of the liquid in determining the phase and morphology, something that has been overlooked in earlier work. A mechanism to explain the effect of oxygen on the nucleation and growth stages has been proposed on the basis of those results and further supported by shaking experiments and ZnS NR synthesis manipulation. The CdS NRs synthesized under different conditions showed obvious differences in photocatalytic activity, which indicated that controlling the synthetic process can lead to materials with tailored photocatalytic activity.     

A low-temperature extraction-solvothermal route to the fabrication of micro-sized MoS2 spheres modified by Cyanex 301

Mono-dispersed molybdenum disulfide micro-spheres with the diameter of 1-3 μm have been successfully synthesized via extraction-solvothermal method at 150 °C. The extractant Cyanex 301 (di-(2,4,4-trimethylpentyl) dithiophosphinic acid) acted as phase transferring agent, reductant, sulfur source and morphology-controlling agent in the whole procedure. The obtained MoS₂ micro-spheres were characterized by XRD, EDS, SEM, TEM, HRTEM, IR, UV-Vis and TG, respectively. The influences of reaction conditions were discussed while a mechanism was proposed to explain the formation of the micro-spheres. Moreover, the tribological properties of liquid paraffin (LP) containing Cyanex 301-modified MoS₂ micro-spheres were also evaluated on a four-ball machine, showing that the obtained MoS₂ product was an excellent oil additive in LP and such lubricant had good anti-wear and friction-reducing properties.     

不同结构Cu_2O多晶的合成及其对高氯酸铵热分解的催化作用

利用均相反应器,在没有添加剂的条件下合成了具有多孔结构的Cu2O微球.考察了合成时间以及反应器旋转速度对Cu2O微球结构的影响.通过增加聚乙烯吡咯烷酮(PVP)的用量,使得Cu2O从多孔微球转变为立方体孪晶,最终形成十四面体孪晶结构.同时,将不同结构的Cu2O多晶应用于催化高氯酸铵(AP)的热分解,结果表明:多孔Cu2O微球较其它结构的Cu2O对AP的热分解具有更高的催化活性,使得AP的低温分解温度降低了37.4°C,而AP在低温阶段的分解量也由8.7%增加至49.0%.     

溶剂热合成Cu2O微球及其对高氯酸铵热分解的催化作用

以聚乙烯吡咯烷酮(PVP)为添加剂,利用溶剂热法合成了Cu2O微球.考察了PVP用量以及反应温度对产物形貌的影响,并在反应时间为2.5与4.5h时分别合成了直径为100-200nm和1μm的Cu2O微球.同时,利用差热分析(DTA)技术考察了不同直径的Cu2O微球对高氯酸铵(AP)热分解的催化效果,结果表明:添加2%(w)的直径为100-200nm和1μm的Cu2O微球使得AP的高温分解温度分别降低了116和118°C,AP在低温阶段的分解量也明显提高.     

Mono-dispersed cross-linked polystyrene micro-spheres prepared by seed swelling polymerization method

A two-step swelling procedure was adopted to synthesize mono-dispersed and highly cross-linked poly (St-divinylbenzene) particles with PSt micro-spheres (1.80 μm in diameter). The PSt micro-spheres were prepared by a dispersion polymerization method and used as seeds. The effects of monomer concentration, ratio of ethanol to water, swelling reagents, crosslinking reagents, swelling temperature and agitation speed on particle size were investigated in detail. The morphologies and size distributions of these micro-spheres were examined by SEM and particle size analysis (PSA). The T _g of the micro-spheres was measured by DSC. The results indicate that the particles (6.20 μm in diameter) exhibit excellent mono dispersed property and high crosslinking degree when the concentration of the swelling reagent was 25%, the concentration of the crosslinking reagents was 23%, the swelling temperature was 30°C and the stirring speed was 150 r/min. __________ Translated from Chinese Journal of Applied Chemistry, 2007, 24(11): 1289–1294     

单源前体合成水溶性的CdS和ZnS纳米晶

0引言量子点(QuantumDots)一般指半径小于或接近玻尔激子半径的半导体纳米晶颗粒。和有机染料分子相比,无机半导体纳米晶的带隙宽度可通过简单     

Biomolecule‐Assisted Construction of Cadmium Sulfide Hollow Spheres with Structure‐Dependent Photocatalytic Activity

In this study, we report the synthesis of monodispersive solid and hollow CdS spheres with structure‐dependent photocatalytic abilities for dye photodegradation. The monodispersive CdS nanospheres were constructed with the assistance of the soulcarboxymthyi chitosan biopolymer under hydrothermal conditions. The solid CdS spheres were corroded by ammonia to form hollow CdS nanospheres through a dissolution–reprecipitation mechanism. Their visible‐light photocatalytic activities were investigated, and the results show that both the solid and the hollow CdS spheres have visible‐light photocatalytic abilities for the photodegradation of dyes. The photocatalytic properties of the CdS spheres were demonstrated to be structure dependent. Although the nanoparticles comprising the hollow spheres have larger sizes than those comprising the solid spheres, the hollow CdS spheres have better photocatalytic performances than the solid CdS spheres, which can be attributed to the special hollow structure.     

Studies on optical absorption and structural properties of Fe doped CdS quantum dots

Fe doped CdS quantum dots have been prepared using simple precursors by chemical precipitation technique. Fe doped CdS quantum dots have been synthesized by mixing cadmium nitrate, sodium sulfide and adding Fe under suitable conditions. X-ray diffraction analysis reveals that undoped and Fe doped CdS crystallizes in hexagonal structure. The lattice constants of Fe doped CdS nanoparticles decreased slightly with incorporation of Fe and no secondary phase was observed. The average grain size of the nanoparticles is found to lie in the range of 2.8–4.2 nm. HRTEM results show that undoped and 3.75% Fe doped CdS nanoparticles exhibit a uniform size distribution and average size of the nanoparticles is about 2–3 nm. Raman spectra show that 1LO and 2LO peaks of the Fe doped CdS samples are slightly red shifted compared with those of undoped CdS. Optical absorption spectra of Fe doped CdS nanoparticles exhibited red shift.     

ITO/TiO2表面电沉积CdS纳米粒子及其薄膜的光电性能

采用阴极恒电位沉积方法, 在TiO2表面沉积制备出CdS纳米粒子. XRD和SEM测试结果表明, CdS粒子的结构以六方晶相为主, 粒径分布均匀, 表面形貌呈菜花状. 通过调节沉积电位和沉积时间等因素在一定程度上可以控制CdS纳米粒子的生长. 随着沉积电位变负, CdS粒子的粒径逐渐减小. 沉积时间越短, 粒子粒径越小. 紫外-可见吸收光谱测试结果表明, 不同条件下制备出来的CdS粒子表现出一定的量子尺寸效应. 此外, 沉积条件也会影响ITO/TiO2/CdS复合半导体薄膜的光电性能.     

碳酸钙微米球的制备与表征

采用醋酸钙和碳酸钠为原料,在反应温度为5℃和柠檬酸三钠质量百分浓度为15%的条件下,采用沉淀法合成出了粒度为1～4μm、分散性好的球形碳酸钙粉体。用扫描电子显微镜(SEM)、X射线衍射仪(XRD)、红外光谱仪(IR)、原子力扫描探针显微镜(ASPM)、光学显微镜、粒度分析仪等对样品进行了表征,并用光学显微镜跟踪考察了碳酸钙微米球的形成过程。结果表明,碳酸钙微米球是由大量纳米级颗粒组装而成。