Preparation and Pb (II) adsorption in aqueous of 2D/2D g‐C3N4/MnO2 composite

A novel g‐C₃N₄/MnO₂ composite was prepared by in situ deposition of MnO₂ on graphitic carbon nitride (g‐C₃N₄) nanosheets, and its adsorption properties were evaluated for removal of Pb (II) in aqueous. Fourier transform‐infrared, spectrometer scanning electron microscopy and transmission electron microscopy characterization showed the g‐C₃N₄/MnO₂ composite had a two‐dimensional/two‐dimensional (2D/2D) structure with ample active sites. The Brunauer–Emmett–Teller specific surface area of g‐C₃N₄/MnO₂ composites (234.9 m²/g) was 13.5 times larger than that of g‐C₃N₄ (17.37 m²/g), providing better conditions for adsorption. The adsorption kinetic data were better fitted with the pseudo‐second‐order model. The Langmuir model was more suitable for describing the experimental equilibrium data of g‐C₃N₄/MnO₂, and the maximum adsorption capacity was 204.1 mg/g for Pb (II). The adsorption of g‐C₃N₄/MnO₂ composite for Pb (II) was an endothermic and spontaneous process, and reached adsorption equilibrium rapidly within initial 150 min. This composite was an excellent adsorbent because of its higher adsorption capacity and facile preparation progress.     

Adsorption characteristics of Titan yellow and Congo red on CoFe2O4 magnetic nanoparticles

This paper assesses the adsorption characteristics of Titan yellow and Congo red on CoFe₂O₄ magnetic nanoparticles. The adsorption behavior of Titan yellow and Congo red from aqueous solution onto CoFe₂O₄ magnetic nanoparticles has been determined by investigating the effects of pH, concentration of the dye, amount of adsorbent, contact time, ionic strength and temperature. Experimental results indicated that CoFe₂O₄ nanoparticles can remove more than 98 % of each dye under optimum operational conditions of a dosage of 15.0 mg CoFe₂O₄, pH 3.0, initial dye concentration of 22–140 mg L^?1, and contact times of 2.0 and 15.0 min for Congo red and Titan yellow, respectively. Langmuir and Freundlich isotherm models have been used to evaluate the ongoing adsorption kinetic equations. Regeneration of the saturated adsorbent was possible by NaCl/acetone solution as eluent. The maximum adsorption capacities were 200.0 and 212.8 mg dye per gram adsorbent for Congo red and Titan yellow, respectively. With the help of adsorption isotherm, thermodynamic parameters such as free energy, enthalpy and entropy have been calculated. On the basis of pseudo-first-order and pseudo-second-order kinetic equations, different kinetic parameters have been obtained.     

Enhanced specific energy of silver-doped MnO2/graphene oxide electrodes as facile fabrication symmetric supercapacitor device

The present work is about the preparation of silver (Ag)-doped manganese oxide (MnO₂)/graphene oxide (GO) composite thin films are deposited by a facile and binder-free successive ionic layer adsorption and reaction (SILAR) method for the first time. The Brunauer-Emmett-Teller (BET) study revealed the nanosheets of MnO₂–Ag3/GO exhibit high specific surface area of 192 m² g^?1. The tailored flower-like morphology and interconnected nanosheets of MnO₂–Ag3/GO electrodes achieved high electrochemical performance. The maximum specific capacitance (Cs) of 877 F g^?1 at the scan rate of 5 mV s^?1 is obtained for MnO₂–Ag3/GO electrode tested in 1 M sodium sulfate (Na₂SO₄) electrolyte with capacity retention of 94.57% after 5000 cycling stability. The MnO₂–Ag3/GO composite-based flexible solid state symmetric supercapacitor (FSS-SSC) device delivered Cs as 164 F g^?1 with specific energy of 57 Wh kg^?1 at specific power of 1.6 kW kg^?1 and capacitive retention of 94% after 10,000 cycles.     

基于医用纱布负载的二氧化锰纳米颗粒用于亚甲蓝染料的去除

以医用纱布(medical gauze,MG)同时作为模板和还原剂,通过原位氧化还原反应,简便地制备了MG负载的MnO₂纳米颗粒(MnO₂ NPs/MG),并对其形貌、成分进行表征。结果表明,MnO₂ NPs均匀地分散于MG纤维表面。结合MnO₂纳米材料的吸附性能和MG复合材料的操作便捷性,将MnO₂ NPs/MG进一步应用于亚甲蓝染料的去除。结果表明,在中性条件下,通过简单的浸泡搅拌,MnO₂ NPs/MG对亚甲蓝的去除率可达85.09%,并且可以通过增大吸附材料用量与染料初始浓度的比例提高去除率。等温吸附和动力学研究证明,MnO₂ NPs/MG对亚甲蓝的吸附符合Langmuir吸附等温模型和拟二级动力学模型。     

基于医用纱布负载的二氧化锰纳米颗粒用于亚甲蓝染料的去除

以医用纱布（medical gauze,MG）同时作为模板和还原剂,通过原位氧化还原反应,简便地制备了MG负载的MnO₂纳米颗粒（MnO₂ NPs/MG）,并对其形貌、成分进行表征。结果表明,MnO₂ NPs均匀地分散于MG纤维表面。结合MnO₂纳米材料的吸附性能和MG复合材料的操作便捷性,将MnO₂ NPs/MG进一步应用于亚甲蓝染料的去除。结果表明,在中性条件下,通过简单的浸泡搅拌,MnO₂ NPs/MG对亚甲蓝的去除率可达85.09%,并且可以通过增大吸附材料用量与染料初始浓度的比例提高去除率。等温吸附和动力学研究证明,MnO₂ NPs/MG对亚甲蓝的吸附符合Langmuir吸附等温模型和拟二级动力学模型。     

Thermodynamics and kinetics of adsorption of Cu(II) from aqueous solutions onto a new cation exchanger derived from tamarind fruit shell

A novel cation exchanger (TFS-CE) having carboxylate functionality was prepared through graft copolymerization of hydroxyethylmethacrylate onto tamarind fruit shell (TFS) in the presence of N,N′-methylenebisacrylamide as a cross-linking agent using K₂S₂O₈/Na₂S₂O₃ initiator system, followed by functionalisation. The TFS-CE was used for the removal of Cu(II) from aqueous solutions. At fixed solid/solution ratio the various factors affecting adsorption such as pH, initial concentration, contact time, and temperature were investigated. Kinetic experiments showed that the amount of Cu(II) adsorbed increased with increase in Cu(II) concentration and equilibrium was attained at 1 h. The kinetics of adsorption follows pseudo-second-order model and the rate constant increases with increase in temperature indicating endothermic nature of adsorption. The Arrhenius and Eyring equations were used to obtain the kinetic parameters such as activation energy (E_a) and enthalpy (ΔH^#), entropy (ΔS^#) and free energy (ΔG^#) of activation for the adsorption process. The value of E_a for adsorption was found to be 10.84 kJ · mol^?1 and the adsorption involves diffusion controlled process. The equilibrium data were well fitted to the Langmuir isotherm. The maximum adsorption capacity for Cu(II) was 64 · 10 mg · g^?1 at T = 303 K. The thermodynamic parameters such as changes in free energy (ΔG^°), enthalpy (ΔH^°), and entropy (ΔS^°) were derived to predict the nature of adsorption process. The isosteric heat of adsorption increases with increase in surface loading indicating some lateral interactions between the adsorbed metal ions.     

Nanostructured spinel-type M(M = Mg,Co, Zn)Cr2O4 oxides: novel adsorbents for aqueous Congo red removal

Nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides with novel adsorbents for aqueous Congo red removal were synthesized by a polyacrylamide gel method and studied for their phase structure, microstructure, adsorption performance, and multiferroic behavior. The phase structure and purity analysis revealed that the nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides presented a spinel-type cubic structure, and the formation of a secondary phase such as Cr₂O₃, MgO, ZnO, or Co₃O₄ was not observed. The microstructure characterization confirmed that the spinel-type MCr₂O₄ oxides grew from fine spherical particles to large rhomboid particles. Adsorption experiments of spinel-type MCr₂O₄ oxides for adsorption of Congo red dye were fitted well with the pseudo-second-order kinetics. The adsorption capacity of the ZnCr₂O₄ oxide (44.038 mg/g, pH 7, temperature 28 °C, initial dye concentration 30 mg/L) was found to be higher than that of MgCr₂O₄ oxide (43.592 mg/g, pH 7, temperature 28 °C) and CoCr₂O₄ oxide (28.718 mg/g, pH 7, temperature 28 °C). The effects of initial adsorbent concentration, initial dye concentration, pH, and temperature between the ZnCr₂O₄ oxide and Congo red dye at which optimal removal occurs, were performed. The thermodynamic studies confirmed that a high temperature favors the adsorption of Congo red dye onto ZnCr₂O₄ oxide studied. The nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides that exhibited high adsorption performance for adsorption of Congo red dye can be ascribed to the synergistic effect of electrostatic interaction, pore filling, and ion exchange. The present work suggested that the nanostructured spinel-type M(M = Mg, Co, Zn)Cr₂O₄ oxides have excellent adsorption performance and multiferroic behavior, which shows potential applications for removal of the Congo red dye from wastewater, magnetic memory recording media, magnetic sensor, energy collection and conversion device, and read/write memory.     

Insight from adsorption properties of Xylidyl Blue embedded hydrogel for effective removal of uranyl: Experimental and theoretical approaches

Applications of a hybrid material consisting of polyacrylamide (PAA) and Xylidyl Blue (XB) for the removal of uranyl ions from aqueous solutions has been investigated with all details. Adsorption experiments were performed at batch mode and constant temperature. Experimental parameters affecting adsorption process such as pH, initial uranyl concentration, time and temperature were studied on the removal of the uranyl ions. The isotherms assays were carried out with synthetic solutions and adsorption data were evaluated by using Langmuir, Freundlich and Dubinin–Radushkevich (D–R) isotherm models. Morphological and chemical characterizations of new synthesized material were investigated by UV-VIS-NIR spectroscopy and SEM/EDX techniques and pH_pzc experiments. The results of the kinetic experiments are consistent with pseudo-second-order models and intra-particle diffusion models with a slightly better fit to the latter. Equilibrium was achieved within 3 h. The value of rate constant for adsorption process was calculated as 1.055 mol⁻¹ kg min⁻¹ at 318 K. The calculated thermodynamic parameters (ΔG°, ΔH° and ΔS°) indicated that the adsorption of uranyl ions onto XB@PAA was feasible, spontaneous and endothermic nature under the studied temperature. The developed material has also a potential as a sensor because its color turn from pink to red by adsorption of uranyl ions.     

银纳米颗粒掺杂的活性微孔炭球：一种高效吸附/催化去除刚果红的双功能材料

以载银纳米颗粒壳聚糖溶液为前驱体,联合喷雾干燥法、高温碳化法和KOH活化法制备出银纳米颗粒掺杂的活性微孔炭球(Ag/AMCSs)。基于一系列表征和性能研究发现,银纳米颗粒均匀分布于Ag/AMCSs结构中,Ag/AMCSs不仅表现出优异的染料吸附性能,而且可以有效催化NaBH₄还原刚果红(CR)的反应。此外,通过研究pH值、接触时间和染料初始浓度对Ag/AMCSs吸附性能的影响,发现Ag/AMCSs对CR的吸附过程符合准二级动力学模型和Langmuir模型,最大吸附量(q_e)可达445mg·g^-1。Ag/AMCSs催化NaBH₄还原CR,反应速率常数k可达0.311min^-1,5次循环利用后,染料催化转化率仍可高达95%。     

Quartzite an efficient adsorbent for the removal of anionic and cationic dyes from aqueous solutions

Quartzite obtained from local source was investigated for the removal of anionic dye congo red (CR) and cationic dye malachite green (MG) as an adsorbent from aqueous solution in batch experiment. The adsorption process was studied as a function of dye concentration, contact time, pH and temperature. Adsorption process was described well by Langmuir and Freundlich isotherms. The adsorption capacity remained 666.7 mg/g for CR dye and 348.125 mg/g for MG dye. Data was analyzed thermodynamically, ΔH⁰ and ΔG⁰ values proved that adsorption of CR and MG is an endothermic and spontaneous process. Adsorption data fitted best in the pseudo-first order kinetic model. The adsorption data proved that quartzite exhibits the best adsorption capacity and can be utilized for the removal of anionic and cationic dyes.     

Adsorption of tetracycline using CuCoFe2O4@Chitosan as a new and green magnetic nanohybrid adsorbent from aqueous solutions: Isotherm,kinetic and thermodynamic study

Utilizing a new microwave-assisted method, CuCoFe₂O₄@Chitosan (Ch) was synthesized as a very strong, magnetically separable nano-adsorbent. The magnetic nanohybrid adsorbent was characterized by FESEM (Field emission scanning electron microscopy), EDS (energy dispersive X-ray), Mapping & Linescan, BET (Brunauer-Emmett-Teller), FTIR (Fourier-transform infrared spectroscopy), XRD (X-ray diffraction analysis), TGA (Thermogravimetric analysis), and VSM (Vibrating Sample Magnetometer) techniques. Then, the adsorption process of Tetracycline (TC) was investigated. The highest percentage of pollutant adsorption on the synthetic and real samples was recorded at an initial concentration of 5 mg/L, pH 3.5, contact time of 20 min, the dose of 0.4 g/L, and temperature of 25 °C, 93.07 %, and 67%, respectively. The TC adsorption process via the synthesized magnetic nanocomposite was consistent with the Freundlich isotherm model (R² = 0.992) and pseudo-second-order kinetic (K₂ = 0.267). The outcomes of thermodynamic analyses, which included entropy changes (ΔS = 10.122 J/mol.k), enthalpy changes (ΔH = ?1.975 kJ/mol), and the Gibbs negative free energy (ΔG = ?4.992 kJ/mol), revealed that the adsorption process was spontaneous, favorable, and exothermic. The good magnetic properties allow easy separation after the adsorption operation. Finally, the efficiency of the nano-adsorbent in the removal process was 82.16% after four adsorption–desorption cycles. Some advantages of this research are a fast and green method for synthesis of adsorbent, fast kinetic, and magnetic properties to easy separation.     

Adsorptive removal of phenol by bagasse fly ash and activated carbon: Equilibrium,kinetics and thermodynamics

Present study deals with the adsorption of phenol on carbon rich bagasse fly ash (BFA) and activated carbon-commercial grade (ACC) and laboratory grade (ACL). BFA is a solid waste obtained from the particulate collection equipment attached to the flue gas line of the bagasse-fired boilers of cane sugar mills. Batch studies were performed to evaluate the influences of various experimental parameters like initial pH (pH₀), contact time, adsorbent dose and initial concentration (C₀) on the removal of phenol. C₀ varied from 75 to 300 mg/l for the adsorption isotherm studies and the effect of temperature on adsorption. Optimum conditions for phenol removal were found to be pH₀ ≈ 6.5, adsorbent dose ≈10 g/l of solution and equilibrium time ≈5 h. Adsorption of phenol followed pseudo-second order kinetics with the initial sorption rate for adsorption on ACL being the highest followed by those on BFA and ACC. The effective diffusion coefficient of phenol is of the order of 10⁻¹⁰ m²/s. Equilibrium isotherms for the adsorption of phenol on BFA, ACC and ACL were analysed by Freundlich, Langmuir, Temkin, Redlich–Peterson, Radke–Prausnitz and Toth isotherm models using non-linear regression technique. Redlich–Peterson isotherm was found to best represent the data for phenol adsorption on all the adsorbents. The change in entropy (ΔS°) and heat of adsorption (ΔH°) for phenol adsorption on BFA were estimated as 1.8 MJ/kg K and 0.5 MJ/kg, respectively. The high negative value of change in Gibbs free energy (ΔG°) indicates the feasible and spontaneous adsorption of phenol on BFA. The values of isosteric heat of adsorption varied with the surface loading of phenol.     

Oxidative degradation of dipeptide (glycyl–glycine) by water-soluble colloidal manganese dioxide in the aqueous and micellar media

The kinetics of the oxidative degradation of dipeptide glycyl–glycine (Gly-Gly) by water-soluble colloidal MnO₂ in acidic medium has been studied by employing visible spectrophotometer in the aqueous and micellar media at 35 °C. To obtain the rate constants as functions of [Gly-Gly], [MnO₂] and [HClO₄], pseudo-first-order conditions were maintained in each kinetic run. The first-order-rate is observed with respect to [MnO₂], whereas fractional-order-rates are determined in both [Gly-Gly] and [HClO₄]. The addition of sodium pyrophosphate and sodium fluoride has composite effects (catalytic and inhibition). The reaction proceeds through the fast adsorption of Gly-Gly on the surface of the colloidal MnO₂. The observed results are discussed in terms of Michaelis–Menten/Langmuir–Hinshelwood model. The Arrhenius and Eyring equations are found valid for the reaction over a range of temperatures and different activation parameters have been evaluated. A probable reaction mechanism, in agreement with the observed kinetic results, has been proposed and discussed. The influence of changes in the surfactant concentrations on the observed rate constant is also investigated and the reaction followed the same type of kinetic behavior in micellar media. The pseudo-first-order rate constant (k_ψ) is found to increase about two-fold with increase in [TX-100]. The catalytic effect of nonionic surfactant TX-100 is explained in terms of the mathematical model proposed by Tuncay et al.     

CoFe2O4@Methylcellulose/AC as a New,Green, and Eco-friendly Nano-magnetic adsorbent for removal of Reactive Red 198 from aqueous solution

Methylcellulose (MC) is the most common commercial cellulose ether and the most attractive biopolymer due to its cheap cost of biodegradability, biocompatibility, hydrophilicity, and lack of toxicity. In this study, CoFe₂O₄@MC/activated carbon (AC) was synthesized as a unique magnetic nano-adsorbent in the presence of MC biopolymer for Reactive Red 198 (RR198) dye removal. The nano-magnetic adsorbent was characterized by FESEM (Field emission scanning electron microscopy), EDS (Energy-dispersive X-ray spectroscopy), Mapping, Linescan, BET (Brunauer–Emmett–Teller), FTIR (Fourier Transform Infrared Spectroscopy), XRD (X-Ray Diffraction), and VSM (Vibrating-Sample magnetometer). For simple separation by external magnetic fields, the Ms value was 57.91 emu/g. According to XRD analysis, the nano-adsorbent maintains its crystal structure, with an average crystal size of 11 nm. The maximum removal efficiencies of RR198 for synthetic and real wastewater samples under optimal conditions (an initial concentration of 10 mg/L, pH 3, contact time of 10 min, nanocomposite dose of 1.5 g/L, and a temperature of 25 °C) were 92.2% and 78%, respectively. The adsorption experiments were fitted well with the Freundlich isotherm (R² = 0.989) and pseudo-second-order kinetic (R² = 0.995). The values of entropy changes (ΔS = 35.087 kJ/mol.k), enthalpy changes (ΔH = -9.862 kJ/mol), and negative Gibbs free energy changes (ΔG) showed that the adsorption process was exothermic. Finally, the reusability findings showed that after six recovery cycles, the efficiency decreased slightly (90.1%). In the end, it can be concluded that the prepared CoFe₂O₄@Methylcellulose/AC can be used as an efficient adsorbent for the removal of RR198 from an aqueous solution.     

Rapid removal of anionic organic dye from contaminated water using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite low-cost adsorbent via adsorption techniques

This research study aims to remove hazardous anionic azo dyes (Congo red (CR)) from aqueous solutions via a simple adsorption method using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite (P3ABA/GO/CoFe₂O₄) as a novel and low-cost nanoadsorbent, as synthesized by a simple and straightforward polymerization method. Typically, 3-aminobenzoic acid (3ABA), as monomer, was chemically polymerized with graphene oxide (GO) and cobalt ferrite (CoFe₂O₄) in an aqueous acidic medium containing an ammonium persulfate initiator. The adsorbent P3ABA/GO/CoFe₂O₄ nanocomposite was characterized using various techniques such as Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, transmission electron microscopy, scanning electron microscopy, energy-dispersive analysis by X-ray and Brunauer–Emmett–Teller, vibrating sample magnetometer, and zeta potential techniques. These techniques confirmed the interaction between the poly(3-aminobenzoic acid) with GO and CoFe₂O₄ due to the presence of π-π interactions, hydrogen bonding, and electrostatic forces. Herein, the removal efficiency of dye from aqueous solution by the adsorbent was studied according to several parameters such as the pH of the solution, dye concentration, dosage of adsorbent, contact time, and temperature. The adsorption of the dye was fitted using a Langmuir model (R² between 0.9980 and 0.9995) at different temperatures, and a kinetic model that was pseudo-second order (R² = between 0.9993 and 0.9929) at various initial concentrations of CR dye. In addition, the data revealed that the P3ABA/GO/CoFe₂O₄ nanocomposite exhibited a high adsorption capacity (153.92 mg/g) and removal for CR dye (98 %) at pH 5. Thermodynamic results showed the adsorption process was an endothermic and spontaneous reaction. It was found that, in terms of reusability, the P3ABA/GO/CoFe₂O₄ adsorbent can be used for up to six cycles. In this study, P3ABA/GO/CoFe₂O₄ nanocomposites were found to be low cost, and have an excellent removal capability and fast adsorption rate for CR from wastewater via a simple adsorption method. Moreover, this adsorbent nanocomposite could be simply separated from the resultant solution and recycled.     

Adsorption of acid blue on synthesized polymeric nanocomposites,PPy/MCM-41 and PAni/MCM-41: Isotherm,thermodynamic and kinetic studies

In the this research, removal of acid blue 62 from aqueous solution using mesoporous crystalline material-41 (MCM-41) loaded by polypyrrole (PPy) and polyaniline (PAni) was investigated. Synthesized composites were characterized by SEM, TEM, FTIR, XRD and BET analysis. Langmuir adsorption isotherm showed the best compatibility with the experimental data in comparison with other isotherm models (q_m = 55.55 mg/L). Kinetic studies proved that the adsorption process is compatible with the pseudo-second-order kinetic model. Thermodynamic parameters such as Gibbs free energy changes (ΔG^o), Enthalpy changes (ΔH^o) and Entropy changes (ΔS^o) were calculated. Negative value of ΔG^o and positive value of ΔH^o show that adsorption of Acid blue 62 on PPy/MCM-41 nanocomposite is a spontaneous process also endothermic.     

Adsorption of cationic methylene blue dye using microwave-assisted activated carbon derived from acacia wood: Optimization and batch studies

This study assesses the performance of optimized acacia wood-based activated carbon (AWAC) as an adsorbent for methylene blue (MB) dye removal in aqueous solution. AWAC was prepared via a physicochemical activation process that consists of potassium hydroxide (KOH) treatment, followed by carbon dioxide (CO₂) gasification under microwave heating. By using response surface methodology (RSM), the optimum preparation conditions of radiation power, radiation time, and KOH-impregnation ratio (IR) were determined to be 360 W, 4.50 min, and 0.90 g/g respectively, which resulted in 81.20 mg/g of MB dye removal and 27.96% of AWAC’s yield. Radiation power and IR had a major effect on MB dye removal while radiation power and radiation time caused the greatest impact on AWAC’s yield. BET surface area, mesopore surface area, and pore volume of optimized AWAC were found to be 1045.56 m²/g, 689.77 m²/g, and 0.54 cm³/g, respectively. Adsorption of MB onto AWAC followed Langmuir and pseudo-second order for isotherm and kinetic studies respectively, with a Langmuir monolayer adsorption capacity of 338.29 mg/g. Mechanism studies revealed that the adsorption process was controlled by film diffusion mechanism and indicated to be thermodynamically exothermic in nature.     

Adsorption of fluoride on synthetic siderite from aqueous solution

The study has investigated the feasibility of using synthetic siderite for F⁻ removal from aqueous solution. Batch experiments were performed to test effects of adsorbent dosage, contact time, initial F⁻ concentration, temperature, solution pH, and coexisting anions on F⁻ removal. Results show that the kinetic rate of F⁻ adsorption was high in the first 2 h, and thereafter significantly decreased. The kinetic data was better fitted to the pseudo-second order kinetic model than the pseudo-first order kinetic model. In comparison with Langmuir isotherm, both Freundlich and Redlich-Peterson isotherms better described the adsorption process, which indicates that the multilayer adsorption should be involved in the process of F⁻ removal. Thermodynamic study manifests that F⁻ adsorption on synthetic siderite was spontaneous and exothermic in nature. The synthetic siderite had high adsorption capacity for F⁻ removal, which was up to 1.775 mg/g in the batch with an adsorbent dosage of 5 g/L and an initial F⁻ concentration of 20 mg/L at 25 °C. The adsorption was relatively independent on solution pH between 4 and 9. The presence of Cl⁻ and NO₃⁻ had less impact on F⁻ adsorption, while PO₄³⁻ significantly affected F⁻ removal from aqueous solution. Results of X-ray diffraction (XRD) and scanning electron microscopy (SEM) suggest that the high adsorption capacity possibly arose from both coprecipitation of ferric hydroxide with F⁻ and adsorption of F⁻ on the fresh goethite.     

Removal of Thiram from Aqueous Solutions

In this study activated carbon was used for the removal of thiram from aqueous solutions. Adsorption experiments were carried out as a function of time, initial thiram concentration and temperature. Equilibrium data fitted well to the Freundlich and Langmuir equilibrium models in the studied concentration range. Adsorption kinetics followed a pseudo second‐order kinetic model rather than pseudo first‐order model. The results from kinetic experiments were used to describe the adsorption mechanism. Both boundary layer and intraparticle diffusion played important role in the adsorption mechanism of thiram. Thermodynamic parameters (ΔG₀, ΔH₀, and ΔS₀) were determined and the adsorption process was found to be an endothermic one. The negative values of ΔG⁰ at different temperatures were indicative of the spontaneity of the adsorption process.     

Adsorption properties of amine modified lignin-hydrogel composite for uranyl ions: Theoretical and experimental insights

A new modified material was synthesized and characterized as ethylene diamine modified (EA) Polyacrylamide (PAA)-Lignin (L). The adsorption features of EA modified PAA-L were studied for uranyl ions. The characterization experiments were evaluated by FT-IR spectroscopic techniques, scanning electron microscopy (SEM), and PZC analysis. Adsorption of UO₂²⁺ ions as a function of concentration, pH, temperature, and time of adsorption were studied. The adsorption phenomenon of UO₂²⁺ ions onto PAA-L-EA from aqueous medium was successfully evaluated by various equilibrium models such as Langmuir, Freundlich, and Dubinin-Radushkevich (DR). The (Qe) maximum adsorption capacity values for Langmuir model was calculated as 0.792 kg mol^?1 by using experimental data. The constant values of thermodynamic parameters such as (ΔG°), (ΔH°) and (ΔS°) were calculated and it has observed that the mechanism of adsorption was found compatible with endothermic and spontaneous owing to increasing disorderliness at solution/solid system. The adsorption mechanism is compatible with Elovich and intraparticle diffusion models. The power of the interaction between modified lignin and uranyl ?on was explained in the light of Hard and Soft Acid-Base Principle.